ARM: i.MX: Remove i.MX1 ADS board support
Subsystems (5)
PATCH 1/2 ARM: i.MX: Remove i.MX1 ADS board support
mx1ads.c can be replaced with devicetree equivalent: imx1-ads.dts, so remove the board file.
Signed-off-by Alexander Shiyan <[email protected]>
--- arch/arm/configs/imx_v4_v5_defconfig | 1 - arch/arm/mach-imx/Kconfig | 11 --- arch/arm/mach-imx/Makefile | 1 - arch/arm/mach-imx/mach-mx1ads.c | 154 ----------------------------------- 4 files changed, 167 deletions(-) delete mode 100644 arch/arm/mach-imx/mach-mx1ads.c
arch/arm/configs/imx_v4_v5_defconfig +0 -1
@@ -22,7 +22,6 @@ CONFIG_ARCH_MULTI_V5=y # CONFIG_ARCH_MULTI_V7 is not set CONFIG_ARCH_MXC=y CONFIG_MXC_IRQ_PRIOR=y -CONFIG_ARCH_MX1ADS=y CONFIG_MACH_SCB9328=y CONFIG_MACH_APF9328=y CONFIG_MACH_MX21ADS=y
arch/arm/mach-imx/Kconfig +0 -11
@@ -109,17 +109,6 @@ config SOC_IMX35 if ARCH_MULTI_V4T comment "MX1 platforms:" -config MACH_MXLADS - bool - -config ARCH_MX1ADS - bool "MX1ADS platform" - select IMX_HAVE_PLATFORM_IMX_I2C - select IMX_HAVE_PLATFORM_IMX_UART - select MACH_MXLADS - select SOC_IMX1 - help - Say Y here if you are using Motorola MX1ADS/MXLADS boards config MACH_SCB9328 bool "Synertronixx scb9328"
arch/arm/mach-imx/Makefile +0 -1
@@ -41,7 +41,6 @@ obj-y += ssi-fiq-ksym.o endif # i.MX1 based machines -obj-$(CONFIG_ARCH_MX1ADS) += mach-mx1ads.o obj-$(CONFIG_MACH_SCB9328) += mach-scb9328.o obj-$(CONFIG_MACH_APF9328) += mach-apf9328.o obj-$(CONFIG_MACH_IMX1_DT) += imx1-dt.o
arch/arm/mach-imx/mach-mx1ads.c deleted +0 -154
154 lines not on this page · raw message
Signature · 1 line
1.8.5.5
PATCH 2/2 ARM: dts: Add support for the i.MX1 Armadeus APF9328 board
This patch adds support for the i.MX1 APF9328 from Armadeus. This change is intended to further remove non-DT support for this board.
Signed-off-by Alexander Shiyan <[email protected]>
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx1-apf9328.dts | 129 +++++++++++++++++++++++++++++++++++++ 2 files changed, 130 insertions(+) create mode 100644 arch/arm/boot/dts/imx1-apf9328.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -162,6 +162,7 @@ dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb dtb-$(CONFIG_ARCH_MXC) += \ imx1-ads.dtb \ + imx1-apf9328.dtb \ imx25-eukrea-mbimxsd25-baseboard.dtb \ imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb \ imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb \
arch/arm/boot/dts/imx1-apf9328.dts new file +129 -0
129 lines not on this page · raw message
Signature · 1 line
1.8.5.5
Shawn Guo
AppliedPATCH 1/2 ARM: i.MX: Remove i.MX1 ADS board support
In reply to Alexander ShiyanQuoted 4 lines · Alexander Shiyan
mx1ads.ccan be replaced with devicetree equivalent:imx1-ads.dts, so remove the board file.Signed-off-by Alexander Shiyan <[email protected]>
Applied both, thanks.