Skip to contentSkip to conversation

mfd: lpc_sch: Intel Quark support

PATCH Applied Andy Shevchenko 2 participants 9 messages Sep 2, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover mfd: lpc_sch: Intel Quark support

This brings support of the LPC SCH device found on Intel Quark SoC. Patches were compile tested, and driver runs on actual hardware.

Please, note that PCI ID will be used in future in the gpio-sch driver.

Changelog v2:
- squash patches 1/5 and 2/5 into 1/4
- add Acked-by Bjorn
- address Lee's comments against 3/4 (former 4/5)
- rebase on newest linux-next

Andy Shevchenko (3):
mfd: lpc_sch: reduce duplicate code and improve manageability
mfd: lpc_sch: Add support for Intel Quark X1000
mfd: lpc_sch: remove FSF address

Josef Ahmad (1):
pci_ids: add support for Intel Quark ILB

 drivers/mfd/lpc_sch.c   | 211 ++++++++++++++++++++++++++++--------------------
 include/linux/pci_ids.h |   1 +
 2 files changed, 126 insertions(+), 86 deletions(-)
Signature · 1 line
2.1.0
#1 lore raw

PATCH v2 1/4 mfd: lpc_sch: reduce duplicate code and improve manageability

This patch refactors the driver to use helper functions instead of copy'n'pasted pieces of code.

It also introduces an additional struct to hold a chipset info. The chipset info will be used to store features that are supported by specific processor or chipset. LPC_SCH supports SMBUS, GPIO and WDT features. As this code base might expand further to support more processors, this implementation will help to keep code base clean and manageable.

The patch is partially based on the work done by Chang Rebecca Swee Fun.

---
 drivers/mfd/lpc_sch.c | 181 +++++++++++++++++++++++++++-----------------------
 1 file changed, 99 insertions(+), 82 deletions(-)
drivers/mfd/lpc_sch.c +99 -82
index 4ee7550..bde070a 100644
@@ -40,120 +40,137 @@
 #define WDTBASE		0x84
 #define WDT_IO_SIZE	64
 
-static struct resource smbus_sch_resource = {
-		.flags = IORESOURCE_IO,
+enum sch_chipsets {
+	LPC_SCH = 0,		/* Intel Poulsbo SCH */
+	LPC_ITC,		/* Intel Tunnel Creek */
+	LPC_CENTERTON,		/* Intel Centerton */
 };
 
-static struct resource gpio_sch_resource = {
-		.flags = IORESOURCE_IO,
+struct lpc_sch_info {
+	unsigned int io_size_smbus;
+	unsigned int io_size_gpio;
+	unsigned int io_size_wdt;
 };
 
-static struct resource wdt_sch_resource = {
-		.flags = IORESOURCE_IO,
-};
-
-static struct mfd_cell lpc_sch_cells[3];
-
-static struct mfd_cell isch_smbus_cell = {
-	.name = "isch_smbus",
-	.num_resources = 1,
-	.resources = &smbus_sch_resource,
-	.ignore_resource_conflicts = true,
-};
-
-static struct mfd_cell sch_gpio_cell = {
-	.name = "sch_gpio",
-	.num_resources = 1,
-	.resources = &gpio_sch_resource,
-	.ignore_resource_conflicts = true,
-};
-
-static struct mfd_cell wdt_sch_cell = {
-	.name = "ie6xx_wdt",
-	.num_resources = 1,
-	.resources = &wdt_sch_resource,
-	.ignore_resource_conflicts = true,
+static struct lpc_sch_info sch_chipset_info[] = {
+	[LPC_SCH] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE,
+	},
+	[LPC_ITC] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE,
+		.io_size_wdt = WDT_IO_SIZE,
+	},
+	[LPC_CENTERTON] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE_CENTERTON,
+		.io_size_wdt = WDT_IO_SIZE,
+	},
 };
 
 static const struct pci_device_id lpc_sch_ids[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB) },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC), LPC_SCH },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC), LPC_ITC },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB), LPC_CENTERTON },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, lpc_sch_ids);
 
-static int lpc_sch_probe(struct pci_dev *dev,
-				const struct pci_device_id *id)
+#define LPC_NO_RESOURCE		1
+#define LPC_SKIP_RESOURCE	2
+
+static int lpc_sch_get_io(struct pci_dev *pdev, int where, const char *name,
+			  struct resource *res, int size)
 {
 	unsigned int base_addr_cfg;
 	unsigned short base_addr;
-	int i, cells = 0;
-	int ret;
 
-	pci_read_config_dword(dev, SMBASE, &base_addr_cfg);
+	if (size == 0)
+		return LPC_NO_RESOURCE;
+
+	pci_read_config_dword(pdev, where, &base_addr_cfg);
 	base_addr = 0;
 	if (!(base_addr_cfg & (1 << 31)))
-		dev_warn(&dev->dev, "Decode of the SMBus I/O range disabled\n");
+		dev_warn(&pdev->dev, "Decode of the %s I/O range disabled\n",
+			 name);
 	else
 		base_addr = (unsigned short)base_addr_cfg;
 
 	if (base_addr == 0) {
-		dev_warn(&dev->dev, "I/O space for SMBus uninitialized\n");
-	} else {
-		lpc_sch_cells[cells++] = isch_smbus_cell;
-		smbus_sch_resource.start = base_addr;
-		smbus_sch_resource.end = base_addr + SMBUS_IO_SIZE - 1;
+		dev_warn(&pdev->dev, "I/O space for %s uninitialized\n", name);
+		return LPC_SKIP_RESOURCE;
 	}
 
-	pci_read_config_dword(dev, GPIOBASE, &base_addr_cfg);
-	base_addr = 0;
-	if (!(base_addr_cfg & (1 << 31)))
-		dev_warn(&dev->dev, "Decode of the GPIO I/O range disabled\n");
-	else
-		base_addr = (unsigned short)base_addr_cfg;
+	res->start = base_addr;
+	res->end = base_addr + size - 1;
+	res->flags = IORESOURCE_IO;
 
-	if (base_addr == 0) {
-		dev_warn(&dev->dev, "I/O space for GPIO uninitialized\n");
-	} else {
-		lpc_sch_cells[cells++] = sch_gpio_cell;
-		gpio_sch_resource.start = base_addr;
-		if (id->device == PCI_DEVICE_ID_INTEL_CENTERTON_ILB)
-			gpio_sch_resource.end = base_addr + GPIO_IO_SIZE_CENTERTON - 1;
-		else
-			gpio_sch_resource.end = base_addr + GPIO_IO_SIZE - 1;
-	}
+	return 0;
+}
 
-	if (id->device == PCI_DEVICE_ID_INTEL_ITC_LPC
-	    || id->device == PCI_DEVICE_ID_INTEL_CENTERTON_ILB) {
-		pci_read_config_dword(dev, WDTBASE, &base_addr_cfg);
-		base_addr = 0;
-		if (!(base_addr_cfg & (1 << 31)))
-			dev_warn(&dev->dev, "Decode of the WDT I/O range disabled\n");
-		else
-			base_addr = (unsigned short)base_addr_cfg;
-		if (base_addr == 0)
-			dev_warn(&dev->dev, "I/O space for WDT uninitialized\n");
-		else {
-			lpc_sch_cells[cells++] = wdt_sch_cell;
-			wdt_sch_resource.start = base_addr;
-			wdt_sch_resource.end = base_addr + WDT_IO_SIZE - 1;
-		}
-	}
+static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
+				 const char *name, int size, int id,
+				 struct mfd_cell *cell)
+{
+	struct resource *res;
+	int ret;
 
-	if (WARN_ON(cells > ARRAY_SIZE(lpc_sch_cells))) {
-		dev_err(&dev->dev, "Cell count exceeds array size");
-		return -ENODEV;
-	}
+	res = devm_kzalloc(&pdev->dev, sizeof(*res), GFP_KERNEL);
+	if (!res)
+		return -ENOMEM;
+
+	ret = lpc_sch_get_io(pdev, where, name, res, size);
+	if (ret)
+		return ret;
+
+	memset(cell, 0, sizeof(*cell));
+
+	cell->name = name;
+	cell->resources = res;
+	cell->num_resources = 1;
+	cell->ignore_resource_conflicts = true;
+	cell->id = id;
+
+	return 0;
+}
+
+static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	struct mfd_cell lpc_sch_cells[3];
+	struct lpc_sch_info *info = &sch_chipset_info[id->driver_data];
+	unsigned int cells = 0;
+	int ret;
+
+	ret = lpc_sch_populate_cell(dev, SMBASE, "isch_smbus",
+				    info->io_size_smbus,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
+
+	ret = lpc_sch_populate_cell(dev, GPIOBASE, "sch_gpio",
+				    info->io_size_gpio,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
+
+	ret = lpc_sch_populate_cell(dev, WDTBASE, "ie6xx_wdt",
+				    info->io_size_wdt,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
 
 	if (cells == 0) {
 		dev_err(&dev->dev, "All decode registers disabled.\n");
 		return -ENODEV;
 	}
 
-	for (i = 0; i < cells; i++)
-		lpc_sch_cells[i].id = id->device;
-
 	ret = mfd_add_devices(&dev->dev, 0, lpc_sch_cells, cells, NULL, 0, NULL);
 	if (ret)
 		mfd_remove_devices(&dev->dev);
Signature · 1 line
2.1.0
Applied
#2 lore raw

Re: [PATCH v2 1/4] mfd: lpc_sch: reduce duplicate code and improve manageability

Quoted 9 lines · Andy Shevchenko

This patch refactors the driver to use helper functions instead of copy'n'pasted pieces of code.

It also introduces an additional struct to hold a chipset info. The chipset info will be used to store features that are supported by specific processor or chipset. LPC_SCH supports SMBUS, GPIO and WDT features. As this code base might expand further to support more processors, this implementation will help to keep code base clean and manageable.

Quoted 7 lines

The patch is partially based on the work done by Chang Rebecca Swee Fun.

---
 drivers/mfd/lpc_sch.c | 181 +++++++++++++++++++++++++++-----------------------
 1 file changed, 99 insertions(+), 82 deletions(-)

Applied, thanks.

Quoted 224 lines
drivers/mfd/lpc_sch.c +99 -82
index 4ee7550..bde070a 100644
@@ -40,120 +40,137 @@
 #define WDTBASE		0x84
 #define WDT_IO_SIZE	64
 
-static struct resource smbus_sch_resource = {
-		.flags = IORESOURCE_IO,
+enum sch_chipsets {
+	LPC_SCH = 0,		/* Intel Poulsbo SCH */
+	LPC_ITC,		/* Intel Tunnel Creek */
+	LPC_CENTERTON,		/* Intel Centerton */
 };
 
-static struct resource gpio_sch_resource = {
-		.flags = IORESOURCE_IO,
+struct lpc_sch_info {
+	unsigned int io_size_smbus;
+	unsigned int io_size_gpio;
+	unsigned int io_size_wdt;
 };
 
-static struct resource wdt_sch_resource = {
-		.flags = IORESOURCE_IO,
-};
-
-static struct mfd_cell lpc_sch_cells[3];
-
-static struct mfd_cell isch_smbus_cell = {
-	.name = "isch_smbus",
-	.num_resources = 1,
-	.resources = &smbus_sch_resource,
-	.ignore_resource_conflicts = true,
-};
-
-static struct mfd_cell sch_gpio_cell = {
-	.name = "sch_gpio",
-	.num_resources = 1,
-	.resources = &gpio_sch_resource,
-	.ignore_resource_conflicts = true,
-};
-
-static struct mfd_cell wdt_sch_cell = {
-	.name = "ie6xx_wdt",
-	.num_resources = 1,
-	.resources = &wdt_sch_resource,
-	.ignore_resource_conflicts = true,
+static struct lpc_sch_info sch_chipset_info[] = {
+	[LPC_SCH] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE,
+	},
+	[LPC_ITC] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE,
+		.io_size_wdt = WDT_IO_SIZE,
+	},
+	[LPC_CENTERTON] = {
+		.io_size_smbus = SMBUS_IO_SIZE,
+		.io_size_gpio = GPIO_IO_SIZE_CENTERTON,
+		.io_size_wdt = WDT_IO_SIZE,
+	},
 };
 
 static const struct pci_device_id lpc_sch_ids[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB) },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC), LPC_SCH },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC), LPC_ITC },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB), LPC_CENTERTON },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, lpc_sch_ids);
 
-static int lpc_sch_probe(struct pci_dev *dev,
-				const struct pci_device_id *id)
+#define LPC_NO_RESOURCE		1
+#define LPC_SKIP_RESOURCE	2
+
+static int lpc_sch_get_io(struct pci_dev *pdev, int where, const char *name,
+			  struct resource *res, int size)
 {
 	unsigned int base_addr_cfg;
 	unsigned short base_addr;
-	int i, cells = 0;
-	int ret;
 
-	pci_read_config_dword(dev, SMBASE, &base_addr_cfg);
+	if (size == 0)
+		return LPC_NO_RESOURCE;
+
+	pci_read_config_dword(pdev, where, &base_addr_cfg);
 	base_addr = 0;
 	if (!(base_addr_cfg & (1 << 31)))
-		dev_warn(&dev->dev, "Decode of the SMBus I/O range disabled\n");
+		dev_warn(&pdev->dev, "Decode of the %s I/O range disabled\n",
+			 name);
 	else
 		base_addr = (unsigned short)base_addr_cfg;
 
 	if (base_addr == 0) {
-		dev_warn(&dev->dev, "I/O space for SMBus uninitialized\n");
-	} else {
-		lpc_sch_cells[cells++] = isch_smbus_cell;
-		smbus_sch_resource.start = base_addr;
-		smbus_sch_resource.end = base_addr + SMBUS_IO_SIZE - 1;
+		dev_warn(&pdev->dev, "I/O space for %s uninitialized\n", name);
+		return LPC_SKIP_RESOURCE;
 	}
 
-	pci_read_config_dword(dev, GPIOBASE, &base_addr_cfg);
-	base_addr = 0;
-	if (!(base_addr_cfg & (1 << 31)))
-		dev_warn(&dev->dev, "Decode of the GPIO I/O range disabled\n");
-	else
-		base_addr = (unsigned short)base_addr_cfg;
+	res->start = base_addr;
+	res->end = base_addr + size - 1;
+	res->flags = IORESOURCE_IO;
 
-	if (base_addr == 0) {
-		dev_warn(&dev->dev, "I/O space for GPIO uninitialized\n");
-	} else {
-		lpc_sch_cells[cells++] = sch_gpio_cell;
-		gpio_sch_resource.start = base_addr;
-		if (id->device == PCI_DEVICE_ID_INTEL_CENTERTON_ILB)
-			gpio_sch_resource.end = base_addr + GPIO_IO_SIZE_CENTERTON - 1;
-		else
-			gpio_sch_resource.end = base_addr + GPIO_IO_SIZE - 1;
-	}
+	return 0;
+}
 
-	if (id->device == PCI_DEVICE_ID_INTEL_ITC_LPC
-	    || id->device == PCI_DEVICE_ID_INTEL_CENTERTON_ILB) {
-		pci_read_config_dword(dev, WDTBASE, &base_addr_cfg);
-		base_addr = 0;
-		if (!(base_addr_cfg & (1 << 31)))
-			dev_warn(&dev->dev, "Decode of the WDT I/O range disabled\n");
-		else
-			base_addr = (unsigned short)base_addr_cfg;
-		if (base_addr == 0)
-			dev_warn(&dev->dev, "I/O space for WDT uninitialized\n");
-		else {
-			lpc_sch_cells[cells++] = wdt_sch_cell;
-			wdt_sch_resource.start = base_addr;
-			wdt_sch_resource.end = base_addr + WDT_IO_SIZE - 1;
-		}
-	}
+static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
+				 const char *name, int size, int id,
+				 struct mfd_cell *cell)
+{
+	struct resource *res;
+	int ret;
 
-	if (WARN_ON(cells > ARRAY_SIZE(lpc_sch_cells))) {
-		dev_err(&dev->dev, "Cell count exceeds array size");
-		return -ENODEV;
-	}
+	res = devm_kzalloc(&pdev->dev, sizeof(*res), GFP_KERNEL);
+	if (!res)
+		return -ENOMEM;
+
+	ret = lpc_sch_get_io(pdev, where, name, res, size);
+	if (ret)
+		return ret;
+
+	memset(cell, 0, sizeof(*cell));
+
+	cell->name = name;
+	cell->resources = res;
+	cell->num_resources = 1;
+	cell->ignore_resource_conflicts = true;
+	cell->id = id;
+
+	return 0;
+}
+
+static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	struct mfd_cell lpc_sch_cells[3];
+	struct lpc_sch_info *info = &sch_chipset_info[id->driver_data];
+	unsigned int cells = 0;
+	int ret;
+
+	ret = lpc_sch_populate_cell(dev, SMBASE, "isch_smbus",
+				    info->io_size_smbus,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
+
+	ret = lpc_sch_populate_cell(dev, GPIOBASE, "sch_gpio",
+				    info->io_size_gpio,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
+
+	ret = lpc_sch_populate_cell(dev, WDTBASE, "ie6xx_wdt",
+				    info->io_size_wdt,
+				    id->device, &lpc_sch_cells[cells]);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		cells++;
 
 	if (cells == 0) {
 		dev_err(&dev->dev, "All decode registers disabled.\n");
 		return -ENODEV;
 	}
 
-	for (i = 0; i < cells; i++)
-		lpc_sch_cells[i].id = id->device;
-
 	ret = mfd_add_devices(&dev->dev, 0, lpc_sch_cells, cells, NULL, 0, NULL);
 	if (ret)
 		mfd_remove_devices(&dev->dev);
Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
#3 lore raw

PATCH v2 2/4 pci_ids: add support for Intel Quark ILB

In reply to Andy Shevchenko

From: Josef Ahmad <[email protected]>

This patch adds the PCI id for Intel Quark ILB. It will be used for GPIO and Multifunction device driver.

---
 include/linux/pci_ids.h | 1 +
 1 file changed, 1 insertion(+)
include/linux/pci_ids.h +1 -0
index 6ed0bb7..4e82195 100644
@@ -2557,6 +2557,7 @@
 #define PCI_DEVICE_ID_INTEL_MFD_EMMC0	0x0823
 #define PCI_DEVICE_ID_INTEL_MFD_EMMC1	0x0824
 #define PCI_DEVICE_ID_INTEL_MRST_SD2	0x084F
+#define PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB	0x095E
 #define PCI_DEVICE_ID_INTEL_I960	0x0960
 #define PCI_DEVICE_ID_INTEL_I960RM	0x0962
 #define PCI_DEVICE_ID_INTEL_CENTERTON_ILB	0x0c60
Signature · 1 line
2.1.0
Applied
#4 lore raw

Re: [PATCH v2 2/4] pci_ids: add support for Intel Quark ILB

Quoted 11 lines · Andy Shevchenko

From: Josef Ahmad <[email protected]>

This patch adds the PCI id for Intel Quark ILB. It will be used for GPIO and Multifunction device driver.

---
 include/linux/pci_ids.h | 1 +
 1 file changed, 1 insertion(+)

Applied, thanks.

Quoted 12 lines
include/linux/pci_ids.h +1 -0
index 6ed0bb7..4e82195 100644
@@ -2557,6 +2557,7 @@
 #define PCI_DEVICE_ID_INTEL_MFD_EMMC0	0x0823
 #define PCI_DEVICE_ID_INTEL_MFD_EMMC1	0x0824
 #define PCI_DEVICE_ID_INTEL_MRST_SD2	0x084F
+#define PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB	0x095E
 #define PCI_DEVICE_ID_INTEL_I960	0x0960
 #define PCI_DEVICE_ID_INTEL_I960RM	0x0962
 #define PCI_DEVICE_ID_INTEL_CENTERTON_ILB	0x0c60
Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
#5 lore raw

PATCH v2 3/4 mfd: lpc_sch: Add support for Intel Quark X1000

In reply to Andy Shevchenko

Intel Quark X1000 SoC supports IRQ based GPIO. This patch will enable MFD support for Quark X1000 and provide IRQ resources to Quark X1000 GPIO device driver.

---
 drivers/mfd/lpc_sch.c | 37 +++++++++++++++++++++++++++++++------
 1 file changed, 31 insertions(+), 6 deletions(-)
drivers/mfd/lpc_sch.c +31 -6
index bde070a..ae614b2 100644
@@ -37,6 +37,9 @@
 #define GPIO_IO_SIZE	64
 #define GPIO_IO_SIZE_CENTERTON	128
 
+/* Intel Quark X1000 GPIO IRQ Number */
+#define GPIO_IRQ_QUARK_X1000	9
+
 #define WDTBASE		0x84
 #define WDT_IO_SIZE	64
 
@@ -44,28 +47,37 @@ enum sch_chipsets {
 	LPC_SCH = 0,		/* Intel Poulsbo SCH */
 	LPC_ITC,		/* Intel Tunnel Creek */
 	LPC_CENTERTON,		/* Intel Centerton */
+	LPC_QUARK_X1000,	/* Intel Quark X1000 */
 };
 
 struct lpc_sch_info {
 	unsigned int io_size_smbus;
 	unsigned int io_size_gpio;
 	unsigned int io_size_wdt;
+	int irq_gpio;
 };
 
 static struct lpc_sch_info sch_chipset_info[] = {
 	[LPC_SCH] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE,
+		.irq_gpio = -1,
 	},
 	[LPC_ITC] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE,
 		.io_size_wdt = WDT_IO_SIZE,
+		.irq_gpio = -1,
 	},
 	[LPC_CENTERTON] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE_CENTERTON,
 		.io_size_wdt = WDT_IO_SIZE,
+		.irq_gpio = -1,
+	},
+	[LPC_QUARK_X1000] = {
+		.io_size_gpio = GPIO_IO_SIZE,
+		.irq_gpio = GPIO_IRQ_QUARK_X1000,
 	},
 };
 
@@ -73,6 +85,7 @@ static const struct pci_device_id lpc_sch_ids[] = {
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC), LPC_SCH },
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC), LPC_ITC },
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB), LPC_CENTERTON },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB), LPC_QUARK_X1000 },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, lpc_sch_ids);
@@ -110,13 +123,13 @@ static int lpc_sch_get_io(struct pci_dev *pdev, int where, const char *name,
 }
 
 static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
-				 const char *name, int size, int id,
-				 struct mfd_cell *cell)
+				 const char *name, int size, int irq,
+				 int id, struct mfd_cell *cell)
 {
 	struct resource *res;
 	int ret;
 
-	res = devm_kzalloc(&pdev->dev, sizeof(*res), GFP_KERNEL);
+	res = devm_kcalloc(&pdev->dev, 2, sizeof(*res), GFP_KERNEL);
 	if (!res)
 		return -ENOMEM;
 
@@ -132,6 +145,18 @@ static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
 	cell->ignore_resource_conflicts = true;
 	cell->id = id;
 
+	/* Check if we need to add an IRQ resource */
+	if (irq < 0)
+		return 0;
+
+	res++;
+
+	res->start = irq;
+	res->end = irq;
+	res->flags = IORESOURCE_IRQ;
+
+	cell->num_resources++;
+
 	return 0;
 }
 
@@ -143,7 +168,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	int ret;
 
 	ret = lpc_sch_populate_cell(dev, SMBASE, "isch_smbus",
-				    info->io_size_smbus,
+				    info->io_size_smbus, -1,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
@@ -151,7 +176,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		cells++;
 
 	ret = lpc_sch_populate_cell(dev, GPIOBASE, "sch_gpio",
-				    info->io_size_gpio,
+				    info->io_size_gpio, info->irq_gpio,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
@@ -159,7 +184,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		cells++;
 
 	ret = lpc_sch_populate_cell(dev, WDTBASE, "ie6xx_wdt",
-				    info->io_size_wdt,
+				    info->io_size_wdt, -1,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
Signature · 1 line
2.1.0
Applied
#6 lore raw

Re: [PATCH v2 3/4] mfd: lpc_sch: Add support for Intel Quark X1000

Quoted 10 lines · Andy Shevchenko

Intel Quark X1000 SoC supports IRQ based GPIO. This patch will enable MFD support for Quark X1000 and provide IRQ resources to Quark X1000 GPIO device driver.

---
 drivers/mfd/lpc_sch.c | 37 +++++++++++++++++++++++++++++++------
 1 file changed, 31 insertions(+), 6 deletions(-)

Applied, thanks.

Quoted 123 lines
drivers/mfd/lpc_sch.c +31 -6
index bde070a..ae614b2 100644
@@ -37,6 +37,9 @@
 #define GPIO_IO_SIZE	64
 #define GPIO_IO_SIZE_CENTERTON	128
 
+/* Intel Quark X1000 GPIO IRQ Number */
+#define GPIO_IRQ_QUARK_X1000	9
+
 #define WDTBASE		0x84
 #define WDT_IO_SIZE	64
 
@@ -44,28 +47,37 @@ enum sch_chipsets {
 	LPC_SCH = 0,		/* Intel Poulsbo SCH */
 	LPC_ITC,		/* Intel Tunnel Creek */
 	LPC_CENTERTON,		/* Intel Centerton */
+	LPC_QUARK_X1000,	/* Intel Quark X1000 */
 };
 
 struct lpc_sch_info {
 	unsigned int io_size_smbus;
 	unsigned int io_size_gpio;
 	unsigned int io_size_wdt;
+	int irq_gpio;
 };
 
 static struct lpc_sch_info sch_chipset_info[] = {
 	[LPC_SCH] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE,
+		.irq_gpio = -1,
 	},
 	[LPC_ITC] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE,
 		.io_size_wdt = WDT_IO_SIZE,
+		.irq_gpio = -1,
 	},
 	[LPC_CENTERTON] = {
 		.io_size_smbus = SMBUS_IO_SIZE,
 		.io_size_gpio = GPIO_IO_SIZE_CENTERTON,
 		.io_size_wdt = WDT_IO_SIZE,
+		.irq_gpio = -1,
+	},
+	[LPC_QUARK_X1000] = {
+		.io_size_gpio = GPIO_IO_SIZE,
+		.irq_gpio = GPIO_IRQ_QUARK_X1000,
 	},
 };
 
@@ -73,6 +85,7 @@ static const struct pci_device_id lpc_sch_ids[] = {
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC), LPC_SCH },
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC), LPC_ITC },
 	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CENTERTON_ILB), LPC_CENTERTON },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB), LPC_QUARK_X1000 },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, lpc_sch_ids);
@@ -110,13 +123,13 @@ static int lpc_sch_get_io(struct pci_dev *pdev, int where, const char *name,
 }
 
 static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
-				 const char *name, int size, int id,
-				 struct mfd_cell *cell)
+				 const char *name, int size, int irq,
+				 int id, struct mfd_cell *cell)
 {
 	struct resource *res;
 	int ret;
 
-	res = devm_kzalloc(&pdev->dev, sizeof(*res), GFP_KERNEL);
+	res = devm_kcalloc(&pdev->dev, 2, sizeof(*res), GFP_KERNEL);
 	if (!res)
 		return -ENOMEM;
 
@@ -132,6 +145,18 @@ static int lpc_sch_populate_cell(struct pci_dev *pdev, int where,
 	cell->ignore_resource_conflicts = true;
 	cell->id = id;
 
+	/* Check if we need to add an IRQ resource */
+	if (irq < 0)
+		return 0;
+
+	res++;
+
+	res->start = irq;
+	res->end = irq;
+	res->flags = IORESOURCE_IRQ;
+
+	cell->num_resources++;
+
 	return 0;
 }
 
@@ -143,7 +168,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	int ret;
 
 	ret = lpc_sch_populate_cell(dev, SMBASE, "isch_smbus",
-				    info->io_size_smbus,
+				    info->io_size_smbus, -1,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
@@ -151,7 +176,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		cells++;
 
 	ret = lpc_sch_populate_cell(dev, GPIOBASE, "sch_gpio",
-				    info->io_size_gpio,
+				    info->io_size_gpio, info->irq_gpio,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
@@ -159,7 +184,7 @@ static int lpc_sch_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		cells++;
 
 	ret = lpc_sch_populate_cell(dev, WDTBASE, "ie6xx_wdt",
-				    info->io_size_wdt,
+				    info->io_size_wdt, -1,
 				    id->device, &lpc_sch_cells[cells]);
 	if (ret < 0)
 		return ret;
Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
#7 lore raw

PATCH v2 4/4 mfd: lpc_sch: remove FSF address

In reply to Andy Shevchenko

This patch removes FSF address because it can be changed. While here, update the copyright lines by adding Intel Corp. to them.

There is no functional change.

---
 drivers/mfd/lpc_sch.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/mfd/lpc_sch.c +1 -4
index ae614b2..c980da4 100644
@@ -7,6 +7,7 @@
  *  Configuration Registers.
  *
  *  Copyright (c) 2010 CompuLab Ltd
+ *  Copyright (c) 2014 Intel Corp.
  *  Author: Denis Turischev <[email protected]>
  *
  *  This program is free software; you can redistribute it and/or modify
@@ -17,10 +18,6 @@
  *  but WITHOUT ANY WARRANTY; without even the implied warranty of
  *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; see the file COPYING.  If not, write to
- *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
 #include <linux/kernel.h>
Signature · 1 line
2.1.0
Applied
#8 lore raw

Re: [PATCH v2 4/4] mfd: lpc_sch: remove FSF address

Quoted 9 lines · Andy Shevchenko

This patch removes FSF address because it can be changed. While here, update the copyright lines by adding Intel Corp. to them.

There is no functional change.

---
 drivers/mfd/lpc_sch.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

Applied, thanks.

Quoted 23 lines
drivers/mfd/lpc_sch.c +1 -4
index ae614b2..c980da4 100644
@@ -7,6 +7,7 @@
  *  Configuration Registers.
  *
  *  Copyright (c) 2010 CompuLab Ltd
+ *  Copyright (c) 2014 Intel Corp.
  *  Author: Denis Turischev <[email protected]>
  *
  *  This program is free software; you can redistribute it and/or modify
@@ -17,10 +18,6 @@
  *  but WITHOUT ANY WARRANTY; without even the implied warranty of
  *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; see the file COPYING.  If not, write to
- *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
 #include <linux/kernel.h>
Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog