Skip to contentSkip to conversation

iio: adc: at91: don't use the last converted data register

PATCH RESEND Superseded Ludovic Desroches 3 participants 5 messages Sep 3, 2014 – Sep 8, 2014

Subsystems (2)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/1 iio: adc: at91: don't use the last converted data register

If touchscreen mode is enabled and a conversion is requested on another channel, the result in the last converted data register can be a touchscreen relative value. Starting a conversion involves to do a conversion for all active channel. It starts with ADC channels and ends with touchscreen channels. Then if ADC_LCD register is not read quickly, its content may be a touchscreen conversion.
To remove this temporal constraint, the conversion value is taken from the channel data register.

---

Sorry for the noise, there was a typo in the CC list.

 drivers/iio/adc/at91_adc.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/iio/adc/at91_adc.c +9 -5
index 3b5bacd..dde22cb 100644
@@ -196,6 +196,7 @@ struct at91_adc_state {
 	bool			done;
 	int			irq;
 	u16			last_value;
+	int			chnb;
 	struct mutex		lock;
 	u8			num_channels;
 	void __iomem		*reg_base;
@@ -274,7 +275,7 @@ void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
 		disable_irq_nosync(irq);
 		iio_trigger_poll(idev->trig, iio_get_time_ns());
 	} else {
-		st->last_value = at91_adc_readl(st, AT91_ADC_LCDR);
+		st->last_value = at91_adc_readl(st, AT91_ADC_CHAN(st, st->chnb));
 		st->done = true;
 		wake_up_interruptible(&st->wq_data_avail);
 	}
@@ -348,10 +349,11 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	unsigned int reg;
 
 	status &= at91_adc_readl(st, AT91_ADC_IMR);
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91RL_ADC_IER_PEN) {
@@ -413,12 +415,13 @@ static irqreturn_t at91_adc_9x5_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	const uint32_t ts_data_irq_mask =
 		AT91_ADC_IER_XRDY |
 		AT91_ADC_IER_YRDY |
 		AT91_ADC_IER_PRDY;
 
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91_ADC_IER_PEN) {
@@ -689,9 +692,10 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&st->lock);
 
+		st->chnb = chan->channel;
 		at91_adc_writel(st, AT91_ADC_CHER,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IER, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IER, 1 << chan->channel);
 		at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_START);
 
 		ret = wait_event_interruptible_timeout(st->wq_data_avail,
@@ -708,7 +712,7 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 
 		at91_adc_writel(st, AT91_ADC_CHDR,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IDR, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IDR, 1 << chan->channel);
 
 		st->last_value = 0;
 		st->done = false;
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH RESEND 1/1 iio: adc: at91: don't use the last converted data register

Quoted 10 lines · Ludovic Desroches

If touchscreen mode is enabled and a conversion is requested on another channel, the result in the last converted data register can be a touchscreen relative value. Starting a conversion involves to do a conversion for all active channel. It starts with ADC channels and ends with touchscreen channels. Then if ADC_LCD register is not read quickly, its content may be a touchscreen conversion.
To remove this temporal constraint, the conversion value is taken from the channel data register.

I wondering whether we should get rid of drdy in the trigger path too. Maybe this can be done in a follow-up patch. Else,

Quoted 80 lines

---

Sorry for the noise, there was a typo in the CC list.

 drivers/iio/adc/at91_adc.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/iio/adc/at91_adc.c +9 -5
index 3b5bacd..dde22cb 100644
@@ -196,6 +196,7 @@ struct at91_adc_state {
 	bool			done;
 	int			irq;
 	u16			last_value;
+	int			chnb;
 	struct mutex		lock;
 	u8			num_channels;
 	void __iomem		*reg_base;
@@ -274,7 +275,7 @@ void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
 		disable_irq_nosync(irq);
 		iio_trigger_poll(idev->trig, iio_get_time_ns());
 	} else {
-		st->last_value = at91_adc_readl(st, AT91_ADC_LCDR);
+		st->last_value = at91_adc_readl(st, AT91_ADC_CHAN(st, st->chnb));
 		st->done = true;
 		wake_up_interruptible(&st->wq_data_avail);
 	}
@@ -348,10 +349,11 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	unsigned int reg;
 
 	status &= at91_adc_readl(st, AT91_ADC_IMR);
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91RL_ADC_IER_PEN) {
@@ -413,12 +415,13 @@ static irqreturn_t at91_adc_9x5_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	const uint32_t ts_data_irq_mask =
 		AT91_ADC_IER_XRDY |
 		AT91_ADC_IER_YRDY |
 		AT91_ADC_IER_PRDY;
 
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91_ADC_IER_PEN) {
@@ -689,9 +692,10 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&st->lock);
 
+		st->chnb = chan->channel;
 		at91_adc_writel(st, AT91_ADC_CHER,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IER, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IER, 1 << chan->channel);
 		at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_START);
 
 		ret = wait_event_interruptible_timeout(st->wq_data_avail,
@@ -708,7 +712,7 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 
 		at91_adc_writel(st, AT91_ADC_CHDR,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IDR, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IDR, 1 << chan->channel);
 
 		st->last_value = 0;
 		st->done = false;
Signature · 1 line
1.7.9.5
Signature · 3 lines
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#2 lore raw

PATCH RESEND 1/1 iio: adc: at91: don't use the last converted data register

Quoted 10 lines · Alexandre Belloni
Quoted 9 lines · Ludovic Desroches

If touchscreen mode is enabled and a conversion is requested on another channel, the result in the last converted data register can be a touchscreen relative value. Starting a conversion involves to do a conversion for all active channel. It starts with ADC channels and ends with touchscreen channels. Then if ADC_LCD register is not read quickly, its content may be a touchscreen conversion.
To remove this temporal constraint, the conversion value is taken from the channel data register.

Quoted 3 lines
Quoted 1 line

I wondering whether we should get rid of drdy in the trigger path too.

Yes we can, then we have to use other interrupts. It could be interesting because when conversion is done, it is done on all active channels and touchscreen (if touchscreen mode is enabled of course). Enabling drdy will cause to receive an interrupt after each conversion (usually we are not fast enough to process irqs one by one, when we get the first drdy irq and when we read the status register, others conversions have already been completed). So getting rid of drdy is a good idea but choosing the appropriate interrupt is a bit more complicated:
- if using touchscreen with pressure measurement, we can rely on prdy
- if using touchscreen without pressure measurement, we can rely on yrdy
- if not using touchscreen, we can rely on EOCx where x is the higher channel number.

Quoted 89 lines

Maybe this can be done in a follow-up patch. Else,

Quoted 80 lines

---

Sorry for the noise, there was a typo in the CC list.

 drivers/iio/adc/at91_adc.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/iio/adc/at91_adc.c +9 -5
index 3b5bacd..dde22cb 100644
@@ -196,6 +196,7 @@ struct at91_adc_state {
 	bool			done;
 	int			irq;
 	u16			last_value;
+	int			chnb;
 	struct mutex		lock;
 	u8			num_channels;
 	void __iomem		*reg_base;
@@ -274,7 +275,7 @@ void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
 		disable_irq_nosync(irq);
 		iio_trigger_poll(idev->trig, iio_get_time_ns());
 	} else {
-		st->last_value = at91_adc_readl(st, AT91_ADC_LCDR);
+		st->last_value = at91_adc_readl(st, AT91_ADC_CHAN(st, st->chnb));
 		st->done = true;
 		wake_up_interruptible(&st->wq_data_avail);
 	}
@@ -348,10 +349,11 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	unsigned int reg;
 
 	status &= at91_adc_readl(st, AT91_ADC_IMR);
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91RL_ADC_IER_PEN) {
@@ -413,12 +415,13 @@ static irqreturn_t at91_adc_9x5_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	const uint32_t ts_data_irq_mask =
 		AT91_ADC_IER_XRDY |
 		AT91_ADC_IER_YRDY |
 		AT91_ADC_IER_PRDY;
 
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91_ADC_IER_PEN) {
@@ -689,9 +692,10 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&st->lock);
 
+		st->chnb = chan->channel;
 		at91_adc_writel(st, AT91_ADC_CHER,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IER, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IER, 1 << chan->channel);
 		at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_START);
 
 		ret = wait_event_interruptible_timeout(st->wq_data_avail,
@@ -708,7 +712,7 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 
 		at91_adc_writel(st, AT91_ADC_CHDR,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IDR, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IDR, 1 << chan->channel);
 
 		st->last_value = 0;
 		st->done = false;
Signature · 1 line
1.7.9.5
Signature · 3 lines
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#3 lore raw

PATCH RESEND 1/1 iio: adc: at91: don't use the last converted data register

In reply to Ludovic Desroches
Quoted 8 lines · Ludovic Desroches

If touchscreen mode is enabled and a conversion is requested on another channel, the result in the last converted data register can be a touchscreen relative value. Starting a conversion involves to do a conversion for all active channel. It starts with ADC channels and ends with touchscreen channels. Then if ADC_LCD register is not read quickly, its content may be a touchscreen conversion.
To remove this temporal constraint, the conversion value is taken from the channel data register.

I would recommend to drop eoc_mask and use GENMASK instead. Also, using BIT(chan->channel) would be a good idea.

Quoted 78 lines

---

Sorry for the noise, there was a typo in the CC list.

 drivers/iio/adc/at91_adc.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/iio/adc/at91_adc.c +9 -5
index 3b5bacd..dde22cb 100644
@@ -196,6 +196,7 @@ struct at91_adc_state {
 	bool			done;
 	int			irq;
 	u16			last_value;
+	int			chnb;
 	struct mutex		lock;
 	u8			num_channels;
 	void __iomem		*reg_base;
@@ -274,7 +275,7 @@ void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
 		disable_irq_nosync(irq);
 		iio_trigger_poll(idev->trig, iio_get_time_ns());
 	} else {
-		st->last_value = at91_adc_readl(st, AT91_ADC_LCDR);
+		st->last_value = at91_adc_readl(st, AT91_ADC_CHAN(st, st->chnb));
 		st->done = true;
 		wake_up_interruptible(&st->wq_data_avail);
 	}
@@ -348,10 +349,11 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	unsigned int reg;
 
 	status &= at91_adc_readl(st, AT91_ADC_IMR);
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91RL_ADC_IER_PEN) {
@@ -413,12 +415,13 @@ static irqreturn_t at91_adc_9x5_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	const uint32_t ts_data_irq_mask =
 		AT91_ADC_IER_XRDY |
 		AT91_ADC_IER_YRDY |
 		AT91_ADC_IER_PRDY;
 
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91_ADC_IER_PEN) {
@@ -689,9 +692,10 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&st->lock);
 
+		st->chnb = chan->channel;
 		at91_adc_writel(st, AT91_ADC_CHER,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IER, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IER, 1 << chan->channel);
 		at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_START);
 
 		ret = wait_event_interruptible_timeout(st->wq_data_avail,
@@ -708,7 +712,7 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 
 		at91_adc_writel(st, AT91_ADC_CHDR,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IDR, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IDR, 1 << chan->channel);
 
 		st->last_value = 0;
 		st->done = false;
#4 lore raw

PATCH RESEND 1/1 iio: adc: at91: don't use the last converted data register

Quoted 10 lines · Hartmut Knaack
Quoted 8 lines · Ludovic Desroches

If touchscreen mode is enabled and a conversion is requested on another channel, the result in the last converted data register can be a touchscreen relative value. Starting a conversion involves to do a conversion for all active channel. It starts with ADC channels and ends with touchscreen channels. Then if ADC_LCD register is not read quickly, its content may be a touchscreen conversion.
To remove this temporal constraint, the conversion value is taken from the channel data register.

I would recommend to drop eoc_mask and use GENMASK instead. Also, using BIT(chan->channel) would be a good idea.

Thanks for your advice, I'll use these macros for v2.

Quoted 79 lines
Quoted 78 lines

---

Sorry for the noise, there was a typo in the CC list.

 drivers/iio/adc/at91_adc.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/iio/adc/at91_adc.c +9 -5
index 3b5bacd..dde22cb 100644
@@ -196,6 +196,7 @@ struct at91_adc_state {
 	bool			done;
 	int			irq;
 	u16			last_value;
+	int			chnb;
 	struct mutex		lock;
 	u8			num_channels;
 	void __iomem		*reg_base;
@@ -274,7 +275,7 @@ void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
 		disable_irq_nosync(irq);
 		iio_trigger_poll(idev->trig, iio_get_time_ns());
 	} else {
-		st->last_value = at91_adc_readl(st, AT91_ADC_LCDR);
+		st->last_value = at91_adc_readl(st, AT91_ADC_CHAN(st, st->chnb));
 		st->done = true;
 		wake_up_interruptible(&st->wq_data_avail);
 	}
@@ -348,10 +349,11 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	unsigned int reg;
 
 	status &= at91_adc_readl(st, AT91_ADC_IMR);
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91RL_ADC_IER_PEN) {
@@ -413,12 +415,13 @@ static irqreturn_t at91_adc_9x5_interrupt(int irq, void *private)
 	struct iio_dev *idev = private;
 	struct at91_adc_state *st = iio_priv(idev);
 	u32 status = at91_adc_readl(st, st->registers->status_register);
+	const u32 eoc_mask = (1 << st->num_channels) - 1;
 	const uint32_t ts_data_irq_mask =
 		AT91_ADC_IER_XRDY |
 		AT91_ADC_IER_YRDY |
 		AT91_ADC_IER_PRDY;
 
-	if (status & st->registers->drdy_mask)
+	if (status & eoc_mask)
 		handle_adc_eoc_trigger(irq, idev);
 
 	if (status & AT91_ADC_IER_PEN) {
@@ -689,9 +692,10 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&st->lock);
 
+		st->chnb = chan->channel;
 		at91_adc_writel(st, AT91_ADC_CHER,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IER, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IER, 1 << chan->channel);
 		at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_START);
 
 		ret = wait_event_interruptible_timeout(st->wq_data_avail,
@@ -708,7 +712,7 @@ static int at91_adc_read_raw(struct iio_dev *idev,
 
 		at91_adc_writel(st, AT91_ADC_CHDR,
 				AT91_ADC_CH(chan->channel));
-		at91_adc_writel(st, AT91_ADC_IDR, st->registers->drdy_mask);
+		at91_adc_writel(st, AT91_ADC_IDR, 1 << chan->channel);
 
 		st->last_value = 0;
 		st->done = false;