watchdog: imx2_wdt: add restart handler support
Subsystems (2)
PATCH 1/1 watchdog: imx2_wdt: add restart handler support
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the driver instead of providing the restart in machine desc.
This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
--- drivers/watchdog/imx2_wdt.c | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
drivers/watchdog/imx2_wdt.c +37 -0
@@ -22,14 +22,17 @@*/ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/init.h> #include <linux/io.h> #include <linux/jiffies.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/moduleparam.h> +#include <linux/notifier.h> #include <linux/of_address.h> #include <linux/platform_device.h> +#include <linux/reboot.h> #include <linux/regmap.h> #include <linux/timer.h> #include <linux/watchdog.h>
@@ -59,6 +62,7 @@ struct imx2_wdt_device {struct regmap *regmap;struct timer_list timer;/* Pings the watchdog when closed */ struct watchdog_device wdog; +struct notifier_block restart_handler; };static bool nowayout =WATCHDOG_NOWAYOUT ;
@@ -77,6 +81,31 @@ static const struct watchdog_info imx2_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE, }; +static int imx2_restart_handler (struct notifier_block *this,unsigned long mode, +void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ; +struct imx2_wdt_device *wdev =container_of (this, + struct imx2_wdt_device, + restart_handler); +/* Assert SRS signal */ +regmap_write (wdev->regmap,0 , wcr_enable); +/* +* Due to imx6q errata ERR004346 (WDOG: WDOG SRS bit requires to be +* written twice), we add another two writes to ensure there must be at +* least two writes happen in the same one 32kHz clock period. We save +* the target check here, since the writes shouldn't be a huge burden +* for other platforms. +*/ +regmap_write (wdev->regmap,0 , wcr_enable); +regmap_write (wdev->regmap,0 , wcr_enable); + +/* wait for reset to assert... */ +mdelay (500 ); + +return NOTIFY_DONE ; +} +static inline void imx2_wdt_setup (struct watchdog_device *wdog) {struct imx2_wdt_device *wdev =watchdog_get_drvdata (wdog);
@@ -257,6 +286,12 @@ static int __init imx2_wdt_probe(struct platform_device *pdev)return ret; } + wdev->restart_handler.notifier_call = imx2_restart_handler; + wdev->restart_handler.priority =128 ; + ret =register_restart_handler (&wdev->restart_handler); +if (ret) +dev_err (&pdev->dev,"cannot register restart handler\n" ); +dev_info (&pdev->dev,"timeout %d sec (nowayout=%d)\n" , wdog->timeout, nowayout);
@@ -268,6 +303,8 @@ static int __exit imx2_wdt_remove(struct platform_device *pdev)struct watchdog_device *wdog =platform_get_drvdata (pdev);struct imx2_wdt_device *wdev =watchdog_get_drvdata (wdog); +unregister_restart_handler (&wdev->restart_handler); +watchdog_unregister_device (wdog);if (imx2_wdt_is_running (wdev)) {
Signature · 1 line
1.8.0
Guenter Roeck
maintainerPATCH 1/1 watchdog: imx2_wdt: add restart handler support
Quoted 42 lines · Jingchang Lu
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the driver instead of providing the restart in machine desc.
This restart handler function is from themxc_restart()
inarch/arm/mach-imx/system.cSigned-off-by Jingchang Lu <[email protected]>--- drivers/watchdog/imx2_wdt.c | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)drivers/watchdog/imx2_wdt.c +4
-0@@ -22,14 +22,17 @@*/ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/init.h> #include <linux/io.h> #include <linux/jiffies.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/moduleparam.h> +#include <linux/notifier.h> #include <linux/of_address.h> #include <linux/platform_device.h> +#include <linux/reboot.h> #include <linux/regmap.h> #include <linux/timer.h> #include <linux/watchdog.h> @@ -59,6 +62,7 @@ struct imx2_wdt_device {struct regmap *regmap;struct timer_list timer;/* Pings the watchdog when closed */ struct watchdog_device wdog; +struct notifier_block restart_handler; };static bool nowayout =WATCHDOG_NOWAYOUT ;
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 87
Quoted 7 lines
drivers/watchdog/imx2_wdt.c +4
-0@@ -77,6 +81,31 @@ static const struct watchdog_info imx2_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE, }; +static int imx2_restart_handler (struct notifier_block *this,unsigned long mode, +void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ;
In the original code this value is conditional depending on cpu_is_mx1(). Are there any implications for this reset mechanism ? Does mx1 have a different watchdog driver ?
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 90
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+struct imx2_wdt_device *wdev =container_of (this, + struct imx2_wdt_device, + restart_handler);
Please align second lines with '('.
Quoted 50 lines
drivers/watchdog/imx2_wdt.c +26
-0+/* Assert SRS signal */ +regmap_write (wdev->regmap,0 , wcr_enable); +/* +* Due to imx6q errata ERR004346 (WDOG: WDOG SRS bit requires to be +* written twice), we add another two writes to ensure there must be at +* least two writes happen in the same one 32kHz clock period. We save +* the target check here, since the writes shouldn't be a huge burden +* for other platforms. +*/ +regmap_write (wdev->regmap,0 , wcr_enable); +regmap_write (wdev->regmap,0 , wcr_enable); + +/* wait for reset to assert... */ +mdelay (500 ); + +return NOTIFY_DONE ; +} +static inline void imx2_wdt_setup (struct watchdog_device *wdog) {struct imx2_wdt_device *wdev =watchdog_get_drvdata (wdog);@@ -257,6 +286,12 @@ static int __init imx2_wdt_probe(struct platform_device *pdev)return ret; } + wdev->restart_handler.notifier_call = imx2_restart_handler; + wdev->restart_handler.priority =128 ; + ret =register_restart_handler (&wdev->restart_handler); +if (ret) +dev_err (&pdev->dev,"cannot register restart handler\n" ); +dev_info (&pdev->dev,"timeout %d sec (nowayout=%d)\n" , wdog->timeout, nowayout);@@ -268,6 +303,8 @@ static int __exit imx2_wdt_remove(struct platform_device *pdev)struct watchdog_device *wdog =platform_get_drvdata (pdev);struct imx2_wdt_device *wdev =watchdog_get_drvdata (wdog); +unregister_restart_handler (&wdev->restart_handler); +watchdog_unregister_device (wdog);if (imx2_wdt_is_running (wdev)) {Signature · 6 lines
1.8.0 -- To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in the body of a message to majordomo at vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH 1/1 watchdog: imx2_wdt: add restart handler support
Quoted 56 lines
-----Original Message-----
From: Guenter Roeck [mailto:groeck7 at gmail.com] On Behalf Of Guenter Roeck
Sent: Thursday, September 11, 2014 11:55 PM
To: Lu Jingchang-B35083
Cc: wim at iguana.be; Guo Shawn-R65073; arnd at arndb.de; linux- watchdog at vger.kernel.org; linux-arm-kernel at lists.infradead.org
Subject: Re: [PATCH] watchdog:imx2_wdt: add restart handler supportQuoted 42 lines · Jingchang Lu
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the driver instead of providing the restart in machine desc.
This restart handler function is from themxc_restart()
inarch/arm/mach-imx/system.cSigned-off-by Jingchang Lu <[email protected]>--- drivers/watchdog/imx2_wdt.c | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)drivers/watchdog/imx2_wdt.c +4
-0@@ -22,14 +22,17 @@*/ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/init.h> #include <linux/io.h> #include <linux/jiffies.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/moduleparam.h> +#include <linux/notifier.h> #include <linux/of_address.h> #include <linux/platform_device.h> +#include <linux/reboot.h> #include <linux/regmap.h> #include <linux/timer.h> #include <linux/watchdog.h> @@ -59,6 +62,7 @@ struct imx2_wdt_device {struct regmap *regmap;struct timer_list timer;/* Pings the watchdog when closed */ struct watchdog_device wdog; +struct notifier_block restart_handler; };static bool nowayout =WATCHDOG_NOWAYOUT ;drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 84
Quoted 4 lines
drivers/watchdog/imx2_wdt.c +1
-0@@ -77,6 +81,31 @@ static const struct watchdog_info imx2_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE, }; +static int imx2_restart_handler(struct notifier_block *this, unsignedlong mode,
Quoted 8 lines
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 87
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+ void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ;In the original code this value is conditional depending on
cpu_is_mx1(). Are there any implications for this reset mechanism ? Does mx1 have a different watchdog driver ?
Hi, Shawn, is this driver also used by the mx1 SoC?
The imx2_wdt.c says it is for IMX2 and later processors, so when moving the restart function, I removed the cpu_is_mx1() condition determination, Thanks.
Quoted 5 lines
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 90
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+struct imx2_wdt_device *wdev =container_of (this, + struct imx2_wdt_device, + restart_handler);Please align second lines with '('.
Ok, thanks.
Best Regards,
Jingchang
Guenter Roeck
maintainerPATCH 1/1 watchdog: imx2_wdt: add restart handler support
Quoted 64 lines · Jingchang Lu
Quoted 56 lines
-----Original Message-----
From: Guenter Roeck [mailto:groeck7 at gmail.com] On Behalf Of Guenter Roeck
Sent: Thursday, September 11, 2014 11:55 PM
To: Lu Jingchang-B35083
Cc: wim at iguana.be; Guo Shawn-R65073; arnd at arndb.de; linux- watchdog at vger.kernel.org; linux-arm-kernel at lists.infradead.org
Subject: Re: [PATCH] watchdog:imx2_wdt: add restart handler supportQuoted 42 lines · Jingchang Lu
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the driver instead of providing the restart in machine desc.
This restart handler function is from themxc_restart()
inarch/arm/mach-imx/system.cSigned-off-by Jingchang Lu <[email protected]>--- drivers/watchdog/imx2_wdt.c | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)drivers/watchdog/imx2_wdt.c +4
-0@@ -22,14 +22,17 @@*/ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/init.h> #include <linux/io.h> #include <linux/jiffies.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/moduleparam.h> +#include <linux/notifier.h> #include <linux/of_address.h> #include <linux/platform_device.h> +#include <linux/reboot.h> #include <linux/regmap.h> #include <linux/timer.h> #include <linux/watchdog.h> @@ -59,6 +62,7 @@ struct imx2_wdt_device {struct regmap *regmap;struct timer_list timer;/* Pings the watchdog when closed */ struct watchdog_device wdog; +struct notifier_block restart_handler; };static bool nowayout =WATCHDOG_NOWAYOUT ;drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 84
Quoted 4 lines
drivers/watchdog/imx2_wdt.c +1
-0@@ -77,6 +81,31 @@ static const struct watchdog_info imx2_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE, }; +static int imx2_restart_handler(struct notifier_block *this, unsignedlong mode,
Quoted 8 lines
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 87
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+ void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ;In the original code this value is conditional depending on
cpu_is_mx1(). Are there any implications for this reset mechanism ? Does mx1 have a different watchdog driver ?
Quoted 4 lines
Hi, Shawn, is this driver also used by the mx1 SoC?
Theimx2_wdt.csays it is for IMX2 and later processors, so when moving the restart function, I removed thecpu_is_mx1()condition determination, Thanks.
I assumed that the original code would be removed. If you have to keep it around for mx1, the conversion doesn't seem to make much sense as you just end up having the code twice. Am I missing something ?
Thanks,
Guenter
PATCH 1/1 watchdog: imx2_wdt: add restart handler support
Quoted 84 lines
-----Original Message-----
From: Guenter Roeck [mailto:linux at roeck-us.net]
Sent: Friday, September 12, 2014 10:49 AM
To: Lu Jingchang-B35083
Cc: wim at iguana.be; Guo Shawn-R65073; arnd at arndb.de; linux- watchdog at vger.kernel.org; linux-arm-kernel at lists.infradead.org
Subject: Re: [PATCH] watchdog:imx2_wdt: add restart handler supportQuoted 16 lines · Jingchang Lu
Quoted 16 lines
-----Original Message-----
From: Guenter Roeck [mailto:groeck7 at gmail.com] On Behalf Of Guenter Roeck
Sent: Thursday, September 11, 2014 11:55 PM
To: Lu Jingchang-B35083
Cc: wim at iguana.be; Guo Shawn-R65073; arnd at arndb.de; linux- watchdog at vger.kernel.org; linux-arm-kernel at lists.infradead.org
Subject: Re: [PATCH] watchdog:imx2_wdt: add restart handler supportQuoted 6 lines · Jingchang Lu
Register the watchdog as the system restart function to the new
introducing kernel restart call chain in the driver instead of providing the restart in machine desc.
This restart handler function is from themxc_restart()inarch/arm/mach-imx/system.cQuoted 3 lines
Quoted 3 lines
Quoted 3 lines
Signed-off-by Jingchang Lu <[email protected]>--- drivers/watchdog/imx2_wdt.c | 37+++++++++++++++++++++++++++++++++++++
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
1 file changed, 37 insertions(+)(quoted diff) +0
-0
b/drivers/watchdog/imx2_wdt.cindex 68c3d37..fa723e8 100644drivers/watchdog/imx2_wdt.c +2
-0@@ -22,14 +22,17 @@*/ #include <linux/clk.h> +#include <linux/delay.h> #include <linux/init.h> #include <linux/io.h> #include <linux/jiffies.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/moduleparam.h> +#include <linux/notifier.h> #include <linux/of_address.h> Quoted 8 lines
Quoted 8 lines
drivers/watchdog/imx2_wdt.c struct imx2_wdt_device { · line 63
Quoted 8 lines
drivers/watchdog/imx2_wdt.c +1
-0#include <linux/platform_device.h> +#include <linux/reboot.h> #include <linux/regmap.h> #include <linux/timer.h> #include <linux/watchdog.h> @@ -59,6 +62,7 @@ struct imx2_wdt_device {struct regmap *regmap;struct timer_list timer;/* Pings the watchdog when closed */
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
drivers/watchdog/imx2_wdt.c +1
-0struct watchdog_device wdog; +struct notifier_block restart_handler; }; static bool nowayout = WATCHDOG_NOWAYOUT; @@ -77,6 +81,31 @@static const struct
watchdog_infoimx2_wdt_info= {
.options =WDIOF_KEEPALIVEPING|WDIOF_SETTIMEOUT|
WDIOF_MAGICCLOSE,Quoted 10 lines
Quoted 10 lines
drivers/watchdog/imx2_wdt.c
Quoted 4 lines
};drivers/watchdog/imx2_wdt.c +2
-0+static int imx2_restart_handler (struct notifier_block *this, +unsignedlong mode,
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 87
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+ void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ;In the original code this value is conditional depending on
cpu_is_mx1().Quoted 6 lines
Quoted 3 lines
Are there any implications for this reset mechanism ? Does mx1 have a different watchdog driver ?
Hi, Shawn, is this driver also used by the mx1 SoC?
Theimx2_wdt.csays it is for IMX2 and later processors, so when moving the restart function, I removed thecpu_is_mx1()condition
Quoted 8 lines
determination, Thanks.
Quoted 1 line
I assumed that the original code would be removed. If you have to keep it around for mx1, the conversion doesn't seem to make much sense as you just end up having the code twice. Am I missing something ?
Thanks,
Guenter
Do you mean removing the code of mxc_restart() in arch/arm/mach-imx/system.c ? Yes, when this patch is accepted, all platform compatible with the imx2_wdt can migrate to the restart handler. I only add the restart handler for imx2_wdt and reserve the original code for that still uses it currently. Thanks.
Best Regards,
Jingchang
PATCH 1/1 watchdog: imx2_wdt: add restart handler support
In reply to Jingchang LuQuoted 14 lines · On Fri, Sep 12, 2014 at 10:42:10AM +0800, Lu Jingchang-B35083 wrote:
Quoted 6 lines
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 84
Quoted 5 lines
drivers/watchdog/imx2_wdt.c +1
-0@@ -77,6 +81,31 @@ static const struct watchdog_info imx2_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE, }; +static int imx2_restart_handler(struct notifier_block *this, unsignedlong mode,
Quoted 8 lines
drivers/watchdog/imx2_wdt.c static const struct watchdog_info imx2_wdt_info = { · line 87
Quoted 3 lines
drivers/watchdog/imx2_wdt.c +3
-0+ void *cmd) +{ +unsigned int wcr_enable =IMX2_WDT_WCR_WDE ;In the original code this value is conditional depending on
cpu_is_mx1(). Are there any implications for this reset mechanism ? Does mx1 have a different watchdog driver ?
Quoted 3 lines
Hi, Shawn, is this driver also used by the mx1 SoC?
Theimx2_wdt.csays it is for IMX2 and later processors, so when moving the restart function, I removed thecpu_is_mx1()condition determination, Thanks.
I think the driver only works for i.MX2 and later ones.
Shawn