spi: davinci: add support for adding delay between word's transmissions
Subsystems (2)
PATCH RESEND v3 1/1 spi: davinci: add support for adding delay between word's transmissions
From: Murali Karicheri <[email protected]>
This patch adds ability to configure delay between transmission of words over SPI bus if it's required by SPI slave devices.
New optional SPI slave property:
- ti,spi-word-delay : delay between transmission of words (SPIFMTn.WDELAY, SPIDAT1.WDEL)
---
Rebased on top of:
spi.git/for-next +
"[PATCH] spi: davinci: remove empty function davinci_spi_cleanup"
http://www.spinics.net/lists/arm-kernel/msg362811.html
v3:
http://www.spinics.net/lists/devicetree/msg49141.html
v2:
http://www.spinics.net/lists/devicetree/msg48514.html
v1:
http://www.spinics.net/lists/linux-spi/msg01609.html
.../devicetree/bindings/spi/spi-davinci.txt | 30 ++++++++++++ drivers/spi/spi-davinci.c | 55 +++++++++++++++++++--- 2 files changed, 78 insertions(+), 7 deletions(-)
Documentation/devicetree/bindings/spi/spi-davinci.txt +30 -0
@@ -1,5 +1,10 @@ Davinci SPI controller device bindings +Links on DM: +Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf +dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf +OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf + Required properties: - #address-cells: number of cells required to define a chip select address on the SPI bus. Should be set to 1.
@@ -24,6 +29,30 @@ Optional: cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; where first three are internal CS and last two are GPIO CS. +Optional properties for slave devices: +SPI slave nodes can contain the following properties. +Not all SPI Peripherals from Texas Instruments support this. +Please check SPI peripheral documentation for a device before using these. + +- ti,spi-wdelay : delay between transmission of words + (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module + clock periods. + + delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period + +Below is timing diagram which shows functional meaning of +"ti,spi-wdelay" parameter. + + +-+ +-+ +-+ +-+ +-+ +-+ +-+ +-+ +SPI_CLK | | | | | | | | | | | | | | | | + +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +- + +SPI_SOMI/SIMO+-----------------+ +----------- + +----------+ word1 +---------------------------+word2 + +-----------------+ +----------- + WDELAY + <--------------------------> + Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus.
@@ -43,6 +72,7 @@ spi0:spi at 20BF0000 { compatible = "st,m25p32"; spi-max-frequency = <25000000>; reg = <0>; + ti,spi-wdelay = <8>; partition at 0 { label = "u-boot-spl";
drivers/spi/spi-davinci.c +48 -7
116 lines not on this page · raw message
Signature · 1 line
1.9.1
Mark Brown
maintainerPATCH RESEND v3 1/1 spi: davinci: add support for adding delay between word's transmissions
Quoted 4 lines · Grygorii Strashko
From: Murali Karicheri <[email protected]>
This patch adds ability to configure delay between transmission of words over SPI bus if it's required by SPI slave devices.
Applied, thanks.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140916/7bca97c8/attachment.sig>