ARM: dts: cm-t54: enable video out, touchscreen and USB3.0
cover ARM: dts: cm-t54: enable video out, touchscreen and USB3.0
Add CM-T54 DT nodes:
* enable HDMI/DVI/LCD video output support
* add ADS7846 touchscreen support
* enchance DWC3 setup to enable power supply for USB3.0 OTG port
Dmitry Lifshitz (4):
ARM: dts: cm-t54: add HDMI/DVI display data
ARM: dts: cm-t54: add Startek LCD support
ARM: dts: cm-t54: add ADS7846 touchscreen support
ARM: dts: cm-t54: setup omap_dwc3
arch/arm/boot/dts/omap5-cm-t54.dts | 268 ++++++++++++++++++++++++++++++++++++ 1 files changed, 268 insertions(+), 0 deletions(-)
Signature · 1 line
1.7.5.4
PATCH 1/4 ARM: dts: cm-t54: add HDMI/DVI display data
Add DSS related pinmux and display data nodes required to support HDMI and DVI video out on CM-T54.
--- arch/arm/boot/dts/omap5-cm-t54.dts | 158 ++++++++++++++++++++++++++++++++++++ 1 files changed, 158 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +158 -0
@@ -66,6 +66,69 @@ default-state = "off"; }; }; + + aliases { + display0 = &hdmi0; + display1 = &dvi0; + }; + + hdmi0: connector at 0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_conn_pins>; + + hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; + + tfp410: encoder at 0 { + compatible = "ti,tfp410"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + + tfp410_in: endpoint at 0 { + remote-endpoint = <&dpi_dvi_out>; + }; + }; + + port at 1 { + reg = <1>; + + tfp410_out: endpoint at 0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector at 1 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c2>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; }; &omap5_pmx_core {
@@ -88,6 +151,13 @@ >; }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
@@ -144,6 +214,53 @@ OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ >; }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ + OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ + >; + }; + + hdmi_conn_pins: pinmux_hdmi_conn_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* dispc_data15 */ + OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* dispc_data14 */ + OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* dispc_data13 */ + OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* dispc_data12 */ + OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* dispc_data11 */ + OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* dispc_data10 */ + OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* dispc_data9 */ + OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* dispc_data8 */ + OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* dispc_data7 */ + OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* dispc_data6 */ + OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* dispc_data5 */ + OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* dispc_data4 */ + OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* dispc_data3 */ + OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* dispc_data2 */ + OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* dispc_data1 */ + OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* dispc_data0 */ + OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* dispc_vsync */ + OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* dispc_hsync */ + OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* dispc_de */ + OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* dispc_pclk */ + OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* dispc_data17 */ + OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* dispc_data16 */ + OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* dispc_data18 */ + OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* dispc_data19 */ + OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* dispc_data20 */ + OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* dispc_data21 */ + OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* dispc_data22 */ + OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* dispc_data23 */ + >; + }; }; &mmc1 {
@@ -398,6 +515,13 @@ }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + &usbhshost { port2-mode = "ehci-hsic"; port3-mode = "ehci-hsic";
@@ -410,3 +534,37 @@ &cpu0 { cpu0-supply = <&smps123_reg>; }; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_dvi_out: endpoint at 0 { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + }; +}; + +&dsi2 { + status = "ok"; + vdd-supply = <&ldo4_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo4_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + lanes = <1 0 3 2 5 4 7 6>; + }; + }; +};
Signature · 1 line
1.7.5.4
PATCH 1/4 ARM: dts: cm-t54: add HDMI/DVI display data
Quoted 13 lines · Dmitry Lifshitz
Add DSS related pinmux and display data nodes required to support HDMI and DVI video out on CM-T54.
Signed-off-by Dmitry Lifshitz <[email protected]>--- arch/arm/boot/dts/omap5-cm-t54.dts | 158 ++++++++++++++++++++++++++++++++++++ 1 files changed, 158 insertions(+), 0 deletions(-)arch/arm/boot/dts/omap5-cm-t54.dts +0
-0
arch/arm/boot/dts/omap5-cm-t54.dts line 73
Quoted 8 lines
arch/arm/boot/dts/omap5-cm-t54.dts +5
-0@@ -66,6 +66,69 @@ default-state = "off"; }; }; + + aliases { + display0 = &hdmi0; + display1 = &dvi0; + };
Should probably maintain all the aliases in one place at the top of the dts?
Quoted 182 lines
arch/arm/boot/dts/omap5-cm-t54.dts +153
-0+ + hdmi0: connector at 0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_conn_pins>; + + hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; + + tfp410: encoder at 0 { + compatible = "ti,tfp410"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + + tfp410_in: endpoint at 0 { + remote-endpoint = <&dpi_dvi_out>; + }; + }; + + port at 1 { + reg = <1>; + + tfp410_out: endpoint at 0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector at 1 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c2>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; }; &omap5_pmx_core {@@ -88,6 +151,13 @@ >; }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */@@ -144,6 +214,53 @@ OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ >; }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ + OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ + >; + }; + + hdmi_conn_pins: pinmux_hdmi_conn_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* dispc_data15 */ + OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* dispc_data14 */ + OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* dispc_data13 */ + OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* dispc_data12 */ + OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* dispc_data11 */ + OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* dispc_data10 */ + OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* dispc_data9 */ + OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* dispc_data8 */ + OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* dispc_data7 */ + OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* dispc_data6 */ + OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* dispc_data5 */ + OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* dispc_data4 */ + OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* dispc_data3 */ + OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* dispc_data2 */ + OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* dispc_data1 */ + OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* dispc_data0 */ + OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* dispc_vsync */ + OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* dispc_hsync */ + OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* dispc_de */ + OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* dispc_pclk */ + OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* dispc_data17 */ + OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* dispc_data16 */ + OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* dispc_data18 */ + OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* dispc_data19 */ + OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* dispc_data20 */ + OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* dispc_data21 */ + OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* dispc_data22 */ + OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* dispc_data23 */ + >; + }; }; &mmc1 {@@ -398,6 +515,13 @@ }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + &usbhshost { port2-mode = "ehci-hsic"; port3-mode = "ehci-hsic";@@ -410,3 +534,37 @@ &cpu0 { cpu0-supply = <&smps123_reg>; }; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_dvi_out: endpoint at 0 { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + }; +}; + +&dsi2 { + status = "ok"; + vdd-supply = <&ldo4_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo4_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + lanes = <1 0 3 2 5 4 7 6>; + }; + }; +};
Signature · 2 lines
Regards, Nishanth Menon
PATCH 2/4 ARM: dts: cm-t54: add Startek LCD support
In reply to Dmitry LifshitzAdd DT support for Startek KD050C LCD 800x480 panel.
--- arch/arm/boot/dts/omap5-cm-t54.dts | 44 ++++++++++++++++++++++++++++++++++++ 1 files changed, 44 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +44 -0
@@ -70,8 +70,41 @@ aliases { display0 = &hdmi0; display1 = &dvi0; + display2 = &lcd0; }; + lcd0: display { + compatible = "startek,startek-kd050c", "panel-dpi"; + label = "lcd"; + + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + + enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>; + + panel-timing { + clock-frequency = <33000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <43>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_lcd_out>; + }; + }; + }; + hdmi0: connector at 0 { compatible = "hdmi-connector"; label = "hdmi";
@@ -223,6 +256,12 @@ >; }; + lcd_pins: pinmux_lcd_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */ + >; + }; + hdmi_conn_pins: pinmux_hdmi_conn_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
@@ -546,6 +585,11 @@ remote-endpoint = <&tfp410_in>; data-lines = <24>; }; + + dpi_lcd_out: endpoint at 1 { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; }; };
Signature · 1 line
1.7.5.4
PATCH 3/4 ARM: dts: cm-t54: add ADS7846 touchscreen support
In reply to Dmitry LifshitzAdd ADS7846 touchscreen support.
--- arch/arm/boot/dts/omap5-cm-t54.dts | 61 ++++++++++++++++++++++++++++++++++++ 1 files changed, 61 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +61 -0
@@ -45,6 +45,13 @@ enable-active-high; }; + ads7846reg: ads7846-reg { + compatible = "regulator-fixed"; + regulator-name = "ads7846-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv";
@@ -164,6 +171,15 @@ }; }; +&omap5_pmx_wkup { + + ads7846_pins: pinmux_ads7846_pins { + pinctrl-single,pins = < + 0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ + >; + }; +}; + &omap5_pmx_core { pinctrl-names = "default"; pinctrl-0 = <
@@ -300,6 +316,51 @@ OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* dispc_data23 */ >; }; + + mcspi2_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk.mcspi2_clk */ + OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo.mcspi2_simo */ + OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi.mcspi2_somi */ + OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0.mcspi2_cs0 */ + >; + }; +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; + + /* touch controller */ + ads7846 at 0 { + pinctrl-names = "default"; + pinctrl-0 = <&ads7846_pins>; + + compatible = "ti,ads7846"; + vcc-supply = <&ads7846reg>; + + reg = <0>; /* CS0 */ + spi-max-frequency = <1500000>; + + interrupt-parent = <&gpio1>; + interrupts = <15 0>; /* gpio1_wk15 */ + pendown-gpio = <&gpio1 15 0>; + + + ti,x-min = /bits/ 16 <0x0>; + ti,x-max = /bits/ 16 <0x0fff>; + ti,y-min = /bits/ 16 <0x0>; + ti,y-max = /bits/ 16 <0x0fff>; + + ti,x-plate-ohms = /bits/ 16 <180>; + ti,pressure-max = /bits/ 16 <255>; + + ti,debounce-max = /bits/ 16 <30>; + ti,debounce-tol = /bits/ 16 <10>; + ti,debounce-rep = /bits/ 16 <1>; + + linux,wakeup; + }; }; &mmc1 {
Signature · 1 line
1.7.5.4
PATCH 4/4 ARM: dts: cm-t54: setup omap_dwc3
In reply to Dmitry LifshitzAdd "extcon" and "vbus-supply" properties of DWC3 node.
--- arch/arm/boot/dts/omap5-cm-t54.dts | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +5 -0
@@ -631,6 +631,11 @@ phys = <0 &hsusb2_phy &hsusb3_phy>; }; +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + &cpu0 { cpu0-supply = <&smps123_reg>; };
Signature · 1 line
1.7.5.4
v2 cover ARM: dts: cm-t54: enable video out, touchscreen and USB3.0
In reply to Dmitry LifshitzAdd CM-T54 DT nodes:
* enable HDMI/DVI/LCD video output support
* add ADS7846 touchscreen support
* enchance DWC3 setup to enable power supply for USB3.0 OTG port
v2: * Fixed comment style issue for mux mode.
Follow the convention mode0_name.modeX_name for pins which mux mode differs from MUX_MODE0
* Moved aliases node to the top of dts file
Dmitry Lifshitz (6):
ARM: dts: sbc-t54: fix mux mode comment style
ARM: dts: cm-t54: fix mux mode comment style
ARM: dts: cm-t54: add HDMI/DVI display data
ARM: dts: cm-t54: add Startek LCD support
ARM: dts: cm-t54: add ADS7846 touchscreen support
ARM: dts: cm-t54: setup omap_dwc3
arch/arm/boot/dts/omap5-cm-t54.dts | 272 ++++++++++++++++++++++++++++++++++- arch/arm/boot/dts/omap5-sbc-t54.dts | 4 +- 2 files changed, 272 insertions(+), 4 deletions(-)
Signature · 1 line
1.7.5.4
PATCH v2 1/6 ARM: dts: sbc-t54: fix mux mode comment style
Follow the comment style of mode0_name.modeX_name for pins which mux mode differs from MUX_MODE0.
---
v2: New patch
arch/arm/boot/dts/omap5-sbc-t54.dts | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/omap5-sbc-t54.dts +2 -2
@@ -19,8 +19,8 @@ mmc1_aux_pins: pinmux_mmc1_aux_pins { pinctrl-single,pins = < - OMAP5_IOPAD(0x0174, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_228 */ - OMAP5_IOPAD(0x0176, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_229 */ + OMAP5_IOPAD(0x0174, PIN_INPUT_PULLUP | MUX_MODE6) /* timer5_pwm_evt.gpio8_228 */ + OMAP5_IOPAD(0x0176, PIN_INPUT_PULLUP | MUX_MODE6) /* timer6_pwm_evt.gpio8_229 */ >; }; };
Signature · 1 line
1.7.5.4
PATCH v2 2/6 ARM: dts: cm-t54: fix mux mode comment style
In reply to Dmitry LifshitzFollow the comment style of mode0_name.modeX_name for pins which mux mode differs from MUX_MODE0.
---
v2: New patch
arch/arm/boot/dts/omap5-cm-t54.dts | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +2 -2
@@ -127,8 +127,8 @@ wlan_gpios_pins: pinmux_wlan_gpios_pins { pinctrl-single,pins = < - OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */ - OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */ + OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */ + OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */ >; };
Signature · 1 line
1.7.5.4
PATCH v2 3/6 ARM: dts: cm-t54: add HDMI/DVI display data
In reply to Dmitry LifshitzAdd DSS related pinmux and display data nodes required to support HDMI and DVI video out on CM-T54.
---
v2: * Fixed comment style issue for mux mode.
Follow the convention mode0_name.modeX_name for pins which mux mode differs from MUX_MODE0
* Moved aliases node to the top of dts file
arch/arm/boot/dts/omap5-cm-t54.dts | 158 ++++++++++++++++++++++++++++++++++++ 1 files changed, 158 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +158 -0
@@ -16,6 +16,11 @@ reg = <0x80000000 0x7F000000>; /* 2048 MB */ }; + aliases { + display0 = &hdmi0; + display1 = &dvi0; + }; + vmmcsd_fixed: fixed-regulator-mmcsd { compatible = "regulator-fixed"; regulator-name = "vmmcsd_fixed";
@@ -66,6 +71,64 @@ default-state = "off"; }; }; + + hdmi0: connector at 0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_conn_pins>; + + hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; + + tfp410: encoder at 0 { + compatible = "ti,tfp410"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + + tfp410_in: endpoint at 0 { + remote-endpoint = <&dpi_dvi_out>; + }; + }; + + port at 1 { + reg = <1>; + + tfp410_out: endpoint at 0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector at 1 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c2>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; }; &omap5_pmx_core {
@@ -88,6 +151,13 @@ >; }; + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + >; + }; + mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
@@ -144,6 +214,53 @@ OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ >; }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */ + OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */ + OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */ + >; + }; + + hdmi_conn_pins: pinmux_hdmi_conn_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */ + OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */ + OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */ + OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */ + OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */ + OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */ + OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */ + OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */ + OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */ + OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */ + OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */ + OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */ + OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */ + OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */ + OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */ + OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */ + OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */ + OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */ + OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */ + OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */ + OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */ + OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */ + OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */ + OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */ + OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */ + OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */ + OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */ + OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */ + >; + }; }; &mmc1 {
@@ -398,6 +515,13 @@ }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + &usbhshost { port2-mode = "ehci-hsic"; port3-mode = "ehci-hsic";
@@ -410,3 +534,37 @@ &cpu0 { cpu0-supply = <&smps123_reg>; }; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_dvi_out: endpoint at 0 { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + }; +}; + +&dsi2 { + status = "ok"; + vdd-supply = <&ldo4_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo4_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + lanes = <1 0 3 2 5 4 7 6>; + }; + }; +};
Signature · 1 line
1.7.5.4
PATCH v2 4/6 ARM: dts: cm-t54: add Startek LCD support
In reply to Dmitry LifshitzAdd DT support for Startek KD050C LCD 800x480 panel.
---
v2: Rebased on top of the previous patch changes
arch/arm/boot/dts/omap5-cm-t54.dts | 44 ++++++++++++++++++++++++++++++++++++ 1 files changed, 44 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +44 -0
@@ -19,6 +19,7 @@ aliases { display0 = &hdmi0; display1 = &dvi0; + display2 = &lcd0; }; vmmcsd_fixed: fixed-regulator-mmcsd {
@@ -72,6 +73,38 @@ }; }; + lcd0: display { + compatible = "startek,startek-kd050c", "panel-dpi"; + label = "lcd"; + + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + + enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>; + + panel-timing { + clock-frequency = <33000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <43>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_lcd_out>; + }; + }; + }; + hdmi0: connector at 0 { compatible = "hdmi-connector"; label = "hdmi";
@@ -223,6 +256,12 @@ >; }; + lcd_pins: pinmux_lcd_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */ + >; + }; + hdmi_conn_pins: pinmux_hdmi_conn_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
@@ -546,6 +585,11 @@ remote-endpoint = <&tfp410_in>; data-lines = <24>; }; + + dpi_lcd_out: endpoint at 1 { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; }; };
Signature · 1 line
1.7.5.4
PATCH v2 5/6 ARM: dts: cm-t54: add ADS7846 touchscreen support
In reply to Dmitry LifshitzAdd ADS7846 touchscreen support.
---
v2: Fixed comment style issue for mux mode.
arch/arm/boot/dts/omap5-cm-t54.dts | 61 ++++++++++++++++++++++++++++++++++++ 1 files changed, 61 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +61 -0
@@ -51,6 +51,13 @@ enable-active-high; }; + ads7846reg: ads7846-reg { + compatible = "regulator-fixed"; + regulator-name = "ads7846-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv";
@@ -164,6 +171,15 @@ }; }; +&omap5_pmx_wkup { + + ads7846_pins: pinmux_ads7846_pins { + pinctrl-single,pins = < + 0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ + >; + }; +}; + &omap5_pmx_core { pinctrl-names = "default"; pinctrl-0 = <
@@ -300,6 +316,51 @@ OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */ >; }; + + mcspi2_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */ + OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */ + >; + }; +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; + + /* touch controller */ + ads7846 at 0 { + pinctrl-names = "default"; + pinctrl-0 = <&ads7846_pins>; + + compatible = "ti,ads7846"; + vcc-supply = <&ads7846reg>; + + reg = <0>; /* CS0 */ + spi-max-frequency = <1500000>; + + interrupt-parent = <&gpio1>; + interrupts = <15 0>; /* gpio1_wk15 */ + pendown-gpio = <&gpio1 15 0>; + + + ti,x-min = /bits/ 16 <0x0>; + ti,x-max = /bits/ 16 <0x0fff>; + ti,y-min = /bits/ 16 <0x0>; + ti,y-max = /bits/ 16 <0x0fff>; + + ti,x-plate-ohms = /bits/ 16 <180>; + ti,pressure-max = /bits/ 16 <255>; + + ti,debounce-max = /bits/ 16 <30>; + ti,debounce-tol = /bits/ 16 <10>; + ti,debounce-rep = /bits/ 16 <1>; + + linux,wakeup; + }; }; &mmc1 {
Signature · 1 line
1.7.5.4
PATCH v2 6/6 ARM: dts: cm-t54: setup omap_dwc3
In reply to Dmitry LifshitzAdd "extcon" and "vbus-supply" properties of DWC3 node.
---
v2: No changes
arch/arm/boot/dts/omap5-cm-t54.dts | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
arch/arm/boot/dts/omap5-cm-t54.dts +5 -0
@@ -631,6 +631,11 @@ phys = <0 &hsusb2_phy &hsusb3_phy>; }; +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + &cpu0 { cpu0-supply = <&smps123_reg>; };
Signature · 1 line
1.7.5.4
v2 cover ARM: dts: cm-t54: enable video out, touchscreen and USB3.0
In reply to Dmitry LifshitzQuoted 20 lines · Dmitry Lifshitz
Add CM-T54 DT nodes:
* enable HDMI/DVI/LCD video output support
* add ADS7846 touchscreen support
* enchance DWC3 setup to enable power supply for USB3.0 OTG portv2: * Fixed comment style issue for mux mode.
Follow the convention mode0_name.modeX_name for pins which mux mode differs fromMUX_MODE0* Moved aliases node to the top of dts file
Dmitry Lifshitz (6):
ARM: dts: sbc-t54: fix mux mode comment style
ARM: dts: cm-t54: fix mux mode comment style
ARM: dts: cm-t54: add HDMI/DVI display data
ARM: dts: cm-t54: add Startek LCD support
ARM: dts: cm-t54: add ADS7846 touchscreen support
ARM: dts: cm-t54: setupomap_dwc3
Quoted 3 lines
arch/arm/boot/dts/omap5-cm-t54.dts | 272 ++++++++++++++++++++++++++++++++++- arch/arm/boot/dts/omap5-sbc-t54.dts | 4 +- 2 files changed, 272 insertions(+), 4 deletions(-)
Applying all into omap-for-v3.18/dt thanks.
Tony