ARM: dts: add board dts file for Exynos3250-based Monk board
Subsystems (3)
PATCH 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCH 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board[1]
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
[1] http://www.spinics.net/lists/arm-kernel/msg366849.html
Signed-off-by Youngjun Cho <[email protected]>
Signed-off-by Chanwoo Choi <[email protected]>
Signed-off-by Inki Dae <[email protected]>
Signed-off-by Seung-Woo Kim <[email protected]>
Signed-off-by Jaehoon Chung <[email protected]>
Signed-off-by Kyungmin Park <[email protected]>
--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 592 ++++++++++++++++++++++++++++++++++ 2 files changed, 594 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dts
arch/arm/boot/dts/Makefile +2 -1
@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \
arch/arm/boot/dts/exynos3250-monk.dts new file +592 -0
592 lines not on this page · raw message
Signature · 1 line
1.8.0
PATCH 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
+ Adding ARM maintainers.
I know it's too late. just to know we trying to push product board support at mainline.
Thank you,
Kyungmin Park
Quoted 654 lines · YoungJun Cho
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCH 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board[1]
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key[1] http://www.spinics.net/lists/arm-kernel/msg366849.html
Signed-off-by Youngjun Cho <[email protected]>Signed-off-by Chanwoo Choi <[email protected]>Signed-off-by Inki Dae <[email protected]>Signed-off-by Seung-Woo Kim <[email protected]>Signed-off-by Jaehoon Chung <[email protected]>Signed-off-by Kyungmin Park <[email protected]>--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 592 ++++++++++++++++++++++++++++++++++ 2 files changed, 594 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dtsarch/arm/boot/dts/Makefile +2
-1@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \arch/arm/boot/dts/exynos3250-monk.dts new file +592
-1@@ -0,0 +1,592 @@ +/* + * Samsung's Exynos3250 based Monk board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Device tree source file for Samsung's Monk board which is based on + * Samsung Exynos3250 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos3250.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung Monk board"; + compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3"; + + aliases { + i2c7 = &i2c_max77836; + }; + + memory { + reg = <0x40000000 0x08000000 + 0x48000000 0x08000000 + 0x50000000 0x08000000 + 0x58000000 0x07F00000>; + }; + + chosen { + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5"; + }; + + firmware at 0205F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0205F000 0x1000>; + } ; + + gpio_keys { + compatible = "gpio-keys"; + + power_key { + interrupt-parent = <&gpx2>; + interrupts = <7 0>; + gpios = <&gpx2 7 1>; + linux,code = <KEY_POWER>; + label = "power key"; + debounce-interval = <10>; + gpio-key,wakeup; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vemmc_reg: voltage-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "V_EMMC_2.8V-fixed"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpk0 2 0>; + enable-active-high; + }; + }; + + i2c_max77836: i2c-gpio-0 { + compatible = "i2c-gpio"; + gpios = <&gpd0 2 0>, <&gpd0 3 0>; + #address-cells = <1>; + #size-cells = <0>; + + max77836: subpmic at 25 { + compatible = "maxim,max77836"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x25>; + wakeup; + + muic: max77836-muic { + compatible = "maxim,max77836-muic"; + }; + + regulators { + compatible = "maxim,max77836-regulator"; + safeout_reg: SAFEOUT { + regulator-name = "SAFEOUT"; + }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <45000>; + regulator-max-microamp = <475000>; + regulator-boot-on; + }; + + motor_reg: LDO1 { + regulator-name = "MOT_2.7V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <2700000>; + }; + + LDO2 { + regulator-name = "UNUSED_LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + }; + }; + + charger { + compatible = "maxim,max77836-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <225000>; + maxim,eoc-uamp = <7500>; + maxim,ovp-uvolt = <6500000>; + }; + }; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; + assigned-clocks = <&cmu CLK_SCLK_TSADC>; + assigned-clock-rates = <6000000>; + + thermistor-ap { + compatible = "ntc,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <100000>; + io-channels = <&adc 0>; + }; + + thermistor-battery { + compatible = "ntc,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <100000>; + io-channels = <&adc 1>; + }; +}; + +&i2c_0 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + status = "okay"; + + s2mps14_pmic at 66 { + compatible = "samsung,s2mps14-pmic"; + interrupt-parent = <&gpx0>; + interrupts = <7 0>; + reg = <0x66>; + wakeup; + + s2mps14_osc: clocks { + compatible = "samsung,s2mps14-clk"; + #clock-cells = <1>; + clock-output-names = "s2mps14_ap", "unused", + "s2mps14_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VAP_ALIVE_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "VAP_M1_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "VCC_AP_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "VAP_AVDD_PLL1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "VAP_PLL_ISO_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "VAP_MIPI_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo7_reg: LDO7 { + regulator-name = "VAP_AVDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "VAP_USB_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo9_reg: LDO9 { + regulator-name = "V_LPDDR_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "UNUSED_LDO10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo11_reg: LDO11 { + regulator-name = "V_EMMC_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + ldo12_reg: LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + ldo13_reg: LDO13 { + regulator-name = "VSENSOR_2.85V"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "UNUSED_LDO14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo15_reg: LDO15 { + regulator-name = "TSP_AVDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo16_reg: LDO16 { + regulator-name = "LCD_VDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo17_reg: LDO17 { + regulator-name = "UNUSED_LDO17"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "UNUSED_LDO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo19_reg: LDO19 { + regulator-name = "TSP_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo20_reg: LDO20 { + regulator-name = "LCD_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo21_reg: LDO21 { + regulator-name = "UNUSED_LDO21"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo22_reg: LDO22 { + regulator-name = "UNUSED_LDO22"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo23_reg: LDO23 { + regulator-name = "UNUSED_LDO23"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo24_reg: LDO24 { + regulator-name = "UNUSED_LDO24"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo25_reg: LDO25 { + regulator-name = "UNUSED_LDO25"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "VAP_MIF_1.0V"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "VAP_ARM_1.0V"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "VAP_INT3D_1.0V"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "VCC_SUB_1.95V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "VCC_SUB_1.35V"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c_1 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + status = "okay"; + + fuelgauge at 36 { + compatible = "maxim,max77836-battery"; + interrupt-parent = <&gpx1>; + interrupts = <2 8>; + reg = <0x36>; + }; +}; + +&i2s2 { + status = "okay"; +}; + +&mshc_0 { + #address-cells = <1>; + #size-cells = <0>; + num-slots = <1>; + broken-cd; + non-removable; + cap-mmc-highspeed; + desc-num = <4>; + mmc-hs200-1_8v; + card-detect-delay = <200>; + vmmc-supply = <&vemmc_reg>; + clock-frequency = <100000000>; + clock-freq-min-max = <400000 100000000>; + samsung,dw-mshc-ciu-div = <1>; + samsung,dw-mshc-sdr-timing = <0 1>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; + bus-width = <8>; + status = "okay"; +}; + +&serial_0 { + assigned-clocks = <&cmu CLK_SCLK_UART0>; + assigned-clock-rates = <100000000>; + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&tmu { + vtmu-supply = <&ldo7_reg>; + status = "okay"; +}; + +&rtc { + clocks = <&cmu CLK_RTC>, <&s2mps14_osc 0>; + clock-names = "rtc", "rtc_src"; + status = "okay"; +}; + +&xusbxti { + clock-frequency = <24000000>; +}; + +&pinctrl_0 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + sleep0: sleep-state { + PIN_SLP(gpa0-0, INPUT, DOWN); + PIN_SLP(gpa0-1, INPUT, DOWN); + PIN_SLP(gpa0-2, INPUT, DOWN); + PIN_SLP(gpa0-3, INPUT, DOWN); + PIN_SLP(gpa0-4, INPUT, DOWN); + PIN_SLP(gpa0-5, INPUT, DOWN); + PIN_SLP(gpa0-6, INPUT, DOWN); + PIN_SLP(gpa0-7, INPUT, DOWN); + + PIN_SLP(gpa1-0, INPUT, DOWN); + PIN_SLP(gpa1-1, INPUT, DOWN); + PIN_SLP(gpa1-2, INPUT, DOWN); + PIN_SLP(gpa1-3, INPUT, DOWN); + PIN_SLP(gpa1-4, INPUT, DOWN); + PIN_SLP(gpa1-5, INPUT, DOWN); + + PIN_SLP(gpb-0, PREV, NONE); + PIN_SLP(gpb-1, PREV, NONE); + PIN_SLP(gpb-2, PREV, NONE); + PIN_SLP(gpb-3, PREV, NONE); + PIN_SLP(gpb-4, INPUT, DOWN); + PIN_SLP(gpb-5, INPUT, DOWN); + PIN_SLP(gpb-6, INPUT, DOWN); + PIN_SLP(gpb-7, INPUT, DOWN); + + PIN_SLP(gpc0-0, INPUT, DOWN); + PIN_SLP(gpc0-1, INPUT, DOWN); + PIN_SLP(gpc0-2, INPUT, DOWN); + PIN_SLP(gpc0-3, INPUT, DOWN); + PIN_SLP(gpc0-4, INPUT, DOWN); + + PIN_SLP(gpc1-0, INPUT, DOWN); + PIN_SLP(gpc1-1, INPUT, DOWN); + PIN_SLP(gpc1-2, INPUT, DOWN); + PIN_SLP(gpc1-3, INPUT, DOWN); + PIN_SLP(gpc1-4, INPUT, DOWN); + + PIN_SLP(gpd0-0, INPUT, DOWN); + PIN_SLP(gpd0-1, INPUT, DOWN); + PIN_SLP(gpd0-2, INPUT, NONE); + PIN_SLP(gpd0-3, INPUT, NONE); + + PIN_SLP(gpd1-0, INPUT, NONE); + PIN_SLP(gpd1-1, INPUT, NONE); + PIN_SLP(gpd1-2, INPUT, NONE); + PIN_SLP(gpd1-3, INPUT, NONE); + }; +}; + +&pinctrl_1 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep1>; + + sleep1: sleep-state { + PIN_SLP(gpe0-0, PREV, NONE); + PIN_SLP(gpe0-1, PREV, NONE); + PIN_SLP(gpe0-2, INPUT, DOWN); + PIN_SLP(gpe0-3, INPUT, DOWN); + PIN_SLP(gpe0-4, PREV, NONE); + PIN_SLP(gpe0-5, INPUT, DOWN); + PIN_SLP(gpe0-6, INPUT, DOWN); + PIN_SLP(gpe0-7, INPUT, DOWN); + + PIN_SLP(gpe1-0, INPUT, DOWN); + PIN_SLP(gpe1-1, PREV, NONE); + PIN_SLP(gpe1-2, INPUT, DOWN); + PIN_SLP(gpe1-3, INPUT, DOWN); + PIN_SLP(gpe1-4, INPUT, DOWN); + PIN_SLP(gpe1-5, INPUT, DOWN); + PIN_SLP(gpe1-6, INPUT, DOWN); + PIN_SLP(gpe1-7, INPUT, NONE); + + PIN_SLP(gpe2-0, INPUT, NONE); + PIN_SLP(gpe2-1, INPUT, NONE); + PIN_SLP(gpe2-2, INPUT, NONE); + + PIN_SLP(gpk0-0, INPUT, DOWN); + PIN_SLP(gpk0-1, INPUT, DOWN); + PIN_SLP(gpk0-2, OUT0, NONE); + PIN_SLP(gpk0-3, INPUT, DOWN); + PIN_SLP(gpk0-4, INPUT, DOWN); + PIN_SLP(gpk0-5, INPUT, DOWN); + PIN_SLP(gpk0-6, INPUT, DOWN); + PIN_SLP(gpk0-7, INPUT, DOWN); + + PIN_SLP(gpk1-0, PREV, NONE); + PIN_SLP(gpk1-1, PREV, NONE); + PIN_SLP(gpk1-2, INPUT, DOWN); + PIN_SLP(gpk1-3, PREV, NONE); + PIN_SLP(gpk1-4, PREV, NONE); + PIN_SLP(gpk1-5, PREV, NONE); + PIN_SLP(gpk1-6, PREV, NONE); + + PIN_SLP(gpk2-0, INPUT, DOWN); + PIN_SLP(gpk2-1, INPUT, DOWN); + PIN_SLP(gpk2-2, INPUT, DOWN); + PIN_SLP(gpk2-3, INPUT, DOWN); + PIN_SLP(gpk2-4, INPUT, DOWN); + PIN_SLP(gpk2-5, INPUT, DOWN); + PIN_SLP(gpk2-6, INPUT, DOWN); + + PIN_SLP(gpl0-0, INPUT, DOWN); + PIN_SLP(gpl0-1, INPUT, DOWN); + PIN_SLP(gpl0-2, INPUT, DOWN); + PIN_SLP(gpl0-3, INPUT, DOWN); + + PIN_SLP(gpm0-0, INPUT, DOWN); + PIN_SLP(gpm0-1, INPUT, DOWN); + PIN_SLP(gpm0-2, INPUT, DOWN); + PIN_SLP(gpm0-3, INPUT, DOWN); + PIN_SLP(gpm0-4, INPUT, DOWN); + PIN_SLP(gpm0-5, INPUT, DOWN); + PIN_SLP(gpm0-6, INPUT, DOWN); + PIN_SLP(gpm0-7, INPUT, DOWN); + + PIN_SLP(gpm1-0, INPUT, DOWN); + PIN_SLP(gpm1-1, INPUT, DOWN); + PIN_SLP(gpm1-2, INPUT, DOWN); + PIN_SLP(gpm1-3, INPUT, DOWN); + PIN_SLP(gpm1-4, INPUT, DOWN); + PIN_SLP(gpm1-5, INPUT, DOWN); + PIN_SLP(gpm1-6, INPUT, DOWN); + + PIN_SLP(gpm2-0, INPUT, DOWN); + PIN_SLP(gpm2-1, INPUT, DOWN); + PIN_SLP(gpm2-2, INPUT, DOWN); + PIN_SLP(gpm2-3, INPUT, DOWN); + PIN_SLP(gpm2-4, INPUT, DOWN); + + PIN_SLP(gpm3-0, INPUT, DOWN); + PIN_SLP(gpm3-1, INPUT, DOWN); + PIN_SLP(gpm3-2, INPUT, DOWN); + PIN_SLP(gpm3-3, INPUT, DOWN); + PIN_SLP(gpm3-4, INPUT, DOWN); + PIN_SLP(gpm3-5, INPUT, DOWN); + PIN_SLP(gpm3-6, INPUT, DOWN); + PIN_SLP(gpm3-7, INPUT, DOWN); + + PIN_SLP(gpm4-0, INPUT, DOWN); + PIN_SLP(gpm4-1, INPUT, DOWN); + PIN_SLP(gpm4-2, INPUT, DOWN); + PIN_SLP(gpm4-3, INPUT, DOWN); + PIN_SLP(gpm4-4, INPUT, DOWN); + PIN_SLP(gpm4-5, INPUT, DOWN); + PIN_SLP(gpm4-6, INPUT, DOWN); + PIN_SLP(gpm4-7, INPUT, DOWN); + }; +}; --1.8.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
In reply to YoungJun ChoQuoted 75 lines · YoungJun Cho
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCH 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board[1]
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key[1] http://www.spinics.net/lists/arm-kernel/msg366849.html
Signed-off-by Youngjun Cho <[email protected]>Signed-off-by Chanwoo Choi <[email protected]>Signed-off-by Inki Dae <[email protected]>Signed-off-by Seung-Woo Kim <[email protected]>Signed-off-by Jaehoon Chung <[email protected]>Signed-off-by Kyungmin Park <[email protected]>--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 592 ++++++++++++++++++++++++++++++++++ 2 files changed, 594 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dtsarch/arm/boot/dts/Makefile +2
-1@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \arch/arm/boot/dts/exynos3250-monk.dts new file +21
-0@@ -0,0 +1,592 @@ +/* + * Samsung's Exynos3250 based Monk board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Device tree source file for Samsung's Monk board which is based on + * Samsung Exynos3250 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos3250.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung Monk board"; + compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3";
arch/arm/boot/dts/exynos3250-monk.dts line 31
Quoted 10 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +10
-0+ + aliases { + i2c7 = &i2c_max77836; + }; + + memory { + reg = <0x40000000 0x08000000 + 0x48000000 0x08000000 + 0x50000000 0x08000000 + 0x58000000 0x07F00000>;
Nit: please bracket list entries individually.
That said, it looks like this could be coalesced into:
memory at 40000000 {
reg = <0x40000000 0x1ff00000>;
};arch/arm/boot/dts/exynos3250-monk.dts line 41
Quoted 10 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +10
-0+ }; + + chosen { + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5"; + }; + + firmware at 0205F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0205F000 0x1000>; + } ;
Nit: useless space before the ';'.
Quoted 19 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +19
-0+ + gpio_keys { + compatible = "gpio-keys"; + + power_key { + interrupt-parent = <&gpx2>; + interrupts = <7 0>; + gpios = <&gpx2 7 1>; + linux,code = <KEY_POWER>; + label = "power key"; + debounce-interval = <10>; + gpio-key,wakeup; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>;
arch/arm/boot/dts/exynos3250-monk.dts line 70
Quoted 10 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +10
-0+ + vemmc_reg: voltage-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "V_EMMC_2.8V-fixed"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpk0 2 0>; + enable-active-high; + }; + };
Why not put this directly under the root node? There's no reason to group regulators simply because they're regulators, and there's only one anyhow.
Mark.
PATCH v2 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
Changes from v1:
- The 'memory' entries coalesce into one entry
- Removes useless space
- Puts voltage-regulator-0 under the root node
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by Youngjun Cho <[email protected]>
Signed-off-by Chanwoo Choi <[email protected]>
Signed-off-by Inki Dae <[email protected]>
Signed-off-by Seung-Woo Kim <[email protected]>
Signed-off-by Jaehoon Chung <[email protected]>
Signed-off-by Kyungmin Park <[email protected]>
--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 583 ++++++++++++++++++++++++++++++++++ 2 files changed, 585 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dts
arch/arm/boot/dts/Makefile +2 -1
@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \
arch/arm/boot/dts/exynos3250-monk.dts new file +583 -0
583 lines not on this page · raw message
Signature · 1 line
1.9.0
PATCH v2 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
Dear Kukjin,
Could you please review or pick this patchset?
Best Regards,
Chanwoo Choi
Quoted 641 lines · YoungJun Cho
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
Changes from v1:
- The 'memory' entries coalesce into one entry
- Removes useless space
- Puts voltage-regulator-0 under the root nodeThis dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power keySigned-off-by Youngjun Cho <[email protected]>Signed-off-by Chanwoo Choi <[email protected]>Signed-off-by Inki Dae <[email protected]>Signed-off-by Seung-Woo Kim <[email protected]>Signed-off-by Jaehoon Chung <[email protected]>Signed-off-by Kyungmin Park <[email protected]>--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 583 ++++++++++++++++++++++++++++++++++ 2 files changed, 585 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dtsarch/arm/boot/dts/Makefile +2
-1@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \arch/arm/boot/dts/exynos3250-monk.dts new file +583
-0@@ -0,0 +1,583 @@ +/* + * Samsung's Exynos3250 based Monk board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Device tree source file for Samsung's Monk board which is based on + * Samsung Exynos3250 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos3250.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung Monk board"; + compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3"; + + aliases { + i2c7 = &i2c_max77836; + }; + + memory { + reg = <0x40000000 0x1ff00000>; + }; + + chosen { + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5"; + }; + + firmware at 0205F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0205F000 0x1000>; + }; + + gpio_keys { + compatible = "gpio-keys"; + + power_key { + interrupt-parent = <&gpx2>; + interrupts = <7 0>; + gpios = <&gpx2 7 1>; + linux,code = <KEY_POWER>; + label = "power key"; + debounce-interval = <10>; + gpio-key,wakeup; + }; + }; + + vemmc_reg: voltage-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "V_EMMC_2.8V-fixed"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpk0 2 0>; + enable-active-high; + }; + + i2c_max77836: i2c-gpio-0 { + compatible = "i2c-gpio"; + gpios = <&gpd0 2 0>, <&gpd0 3 0>; + #address-cells = <1>; + #size-cells = <0>; + + max77836: subpmic at 25 { + compatible = "maxim,max77836"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x25>; + wakeup; + + muic: max77836-muic { + compatible = "maxim,max77836-muic"; + }; + + regulators { + compatible = "maxim,max77836-regulator"; + safeout_reg: SAFEOUT { + regulator-name = "SAFEOUT"; + }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <45000>; + regulator-max-microamp = <475000>; + regulator-boot-on; + }; + + motor_reg: LDO1 { + regulator-name = "MOT_2.7V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <2700000>; + }; + + LDO2 { + regulator-name = "UNUSED_LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + }; + }; + + charger { + compatible = "maxim,max77836-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <225000>; + maxim,eoc-uamp = <7500>; + maxim,ovp-uvolt = <6500000>; + }; + }; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; + assigned-clocks = <&cmu CLK_SCLK_TSADC>; + assigned-clock-rates = <6000000>; + + thermistor-ap { + compatible = "ntc,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <100000>; + io-channels = <&adc 0>; + }; + + thermistor-battery { + compatible = "ntc,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <100000>; + io-channels = <&adc 1>; + }; +}; + +&i2c_0 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + status = "okay"; + + s2mps14_pmic at 66 { + compatible = "samsung,s2mps14-pmic"; + interrupt-parent = <&gpx0>; + interrupts = <7 0>; + reg = <0x66>; + wakeup; + + s2mps14_osc: clocks { + compatible = "samsung,s2mps14-clk"; + #clock-cells = <1>; + clock-output-names = "s2mps14_ap", "unused", + "s2mps14_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VAP_ALIVE_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "VAP_M1_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "VCC_AP_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "VAP_AVDD_PLL1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "VAP_PLL_ISO_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "VAP_MIPI_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo7_reg: LDO7 { + regulator-name = "VAP_AVDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "VAP_USB_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo9_reg: LDO9 { + regulator-name = "V_LPDDR_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "UNUSED_LDO10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo11_reg: LDO11 { + regulator-name = "V_EMMC_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + ldo12_reg: LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + ldo13_reg: LDO13 { + regulator-name = "VSENSOR_2.85V"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "UNUSED_LDO14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo15_reg: LDO15 { + regulator-name = "TSP_AVDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo16_reg: LDO16 { + regulator-name = "LCD_VDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo17_reg: LDO17 { + regulator-name = "UNUSED_LDO17"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "UNUSED_LDO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo19_reg: LDO19 { + regulator-name = "TSP_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo20_reg: LDO20 { + regulator-name = "LCD_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo21_reg: LDO21 { + regulator-name = "UNUSED_LDO21"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo22_reg: LDO22 { + regulator-name = "UNUSED_LDO22"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo23_reg: LDO23 { + regulator-name = "UNUSED_LDO23"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo24_reg: LDO24 { + regulator-name = "UNUSED_LDO24"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo25_reg: LDO25 { + regulator-name = "UNUSED_LDO25"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "VAP_MIF_1.0V"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "VAP_ARM_1.0V"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "VAP_INT3D_1.0V"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "VCC_SUB_1.95V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "VCC_SUB_1.35V"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c_1 { + #address-cells = <1>; + #size-cells = <0>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + status = "okay"; + + fuelgauge at 36 { + compatible = "maxim,max77836-battery"; + interrupt-parent = <&gpx1>; + interrupts = <2 8>; + reg = <0x36>; + }; +}; + +&i2s2 { + status = "okay"; +}; + +&mshc_0 { + #address-cells = <1>; + #size-cells = <0>; + num-slots = <1>; + broken-cd; + non-removable; + cap-mmc-highspeed; + desc-num = <4>; + mmc-hs200-1_8v; + card-detect-delay = <200>; + vmmc-supply = <&vemmc_reg>; + clock-frequency = <100000000>; + clock-freq-min-max = <400000 100000000>; + samsung,dw-mshc-ciu-div = <1>; + samsung,dw-mshc-sdr-timing = <0 1>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; + bus-width = <8>; + status = "okay"; +}; + +&serial_0 { + assigned-clocks = <&cmu CLK_SCLK_UART0>; + assigned-clock-rates = <100000000>; + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&tmu { + vtmu-supply = <&ldo7_reg>; + status = "okay"; +}; + +&rtc { + clocks = <&cmu CLK_RTC>, <&s2mps14_osc 0>; + clock-names = "rtc", "rtc_src"; + status = "okay"; +}; + +&xusbxti { + clock-frequency = <24000000>; +}; + +&pinctrl_0 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + sleep0: sleep-state { + PIN_SLP(gpa0-0, INPUT, DOWN); + PIN_SLP(gpa0-1, INPUT, DOWN); + PIN_SLP(gpa0-2, INPUT, DOWN); + PIN_SLP(gpa0-3, INPUT, DOWN); + PIN_SLP(gpa0-4, INPUT, DOWN); + PIN_SLP(gpa0-5, INPUT, DOWN); + PIN_SLP(gpa0-6, INPUT, DOWN); + PIN_SLP(gpa0-7, INPUT, DOWN); + + PIN_SLP(gpa1-0, INPUT, DOWN); + PIN_SLP(gpa1-1, INPUT, DOWN); + PIN_SLP(gpa1-2, INPUT, DOWN); + PIN_SLP(gpa1-3, INPUT, DOWN); + PIN_SLP(gpa1-4, INPUT, DOWN); + PIN_SLP(gpa1-5, INPUT, DOWN); + + PIN_SLP(gpb-0, PREV, NONE); + PIN_SLP(gpb-1, PREV, NONE); + PIN_SLP(gpb-2, PREV, NONE); + PIN_SLP(gpb-3, PREV, NONE); + PIN_SLP(gpb-4, INPUT, DOWN); + PIN_SLP(gpb-5, INPUT, DOWN); + PIN_SLP(gpb-6, INPUT, DOWN); + PIN_SLP(gpb-7, INPUT, DOWN); + + PIN_SLP(gpc0-0, INPUT, DOWN); + PIN_SLP(gpc0-1, INPUT, DOWN); + PIN_SLP(gpc0-2, INPUT, DOWN); + PIN_SLP(gpc0-3, INPUT, DOWN); + PIN_SLP(gpc0-4, INPUT, DOWN); + + PIN_SLP(gpc1-0, INPUT, DOWN); + PIN_SLP(gpc1-1, INPUT, DOWN); + PIN_SLP(gpc1-2, INPUT, DOWN); + PIN_SLP(gpc1-3, INPUT, DOWN); + PIN_SLP(gpc1-4, INPUT, DOWN); + + PIN_SLP(gpd0-0, INPUT, DOWN); + PIN_SLP(gpd0-1, INPUT, DOWN); + PIN_SLP(gpd0-2, INPUT, NONE); + PIN_SLP(gpd0-3, INPUT, NONE); + + PIN_SLP(gpd1-0, INPUT, NONE); + PIN_SLP(gpd1-1, INPUT, NONE); + PIN_SLP(gpd1-2, INPUT, NONE); + PIN_SLP(gpd1-3, INPUT, NONE); + }; +}; + +&pinctrl_1 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep1>; + + sleep1: sleep-state { + PIN_SLP(gpe0-0, PREV, NONE); + PIN_SLP(gpe0-1, PREV, NONE); + PIN_SLP(gpe0-2, INPUT, DOWN); + PIN_SLP(gpe0-3, INPUT, DOWN); + PIN_SLP(gpe0-4, PREV, NONE); + PIN_SLP(gpe0-5, INPUT, DOWN); + PIN_SLP(gpe0-6, INPUT, DOWN); + PIN_SLP(gpe0-7, INPUT, DOWN); + + PIN_SLP(gpe1-0, INPUT, DOWN); + PIN_SLP(gpe1-1, PREV, NONE); + PIN_SLP(gpe1-2, INPUT, DOWN); + PIN_SLP(gpe1-3, INPUT, DOWN); + PIN_SLP(gpe1-4, INPUT, DOWN); + PIN_SLP(gpe1-5, INPUT, DOWN); + PIN_SLP(gpe1-6, INPUT, DOWN); + PIN_SLP(gpe1-7, INPUT, NONE); + + PIN_SLP(gpe2-0, INPUT, NONE); + PIN_SLP(gpe2-1, INPUT, NONE); + PIN_SLP(gpe2-2, INPUT, NONE); + + PIN_SLP(gpk0-0, INPUT, DOWN); + PIN_SLP(gpk0-1, INPUT, DOWN); + PIN_SLP(gpk0-2, OUT0, NONE); + PIN_SLP(gpk0-3, INPUT, DOWN); + PIN_SLP(gpk0-4, INPUT, DOWN); + PIN_SLP(gpk0-5, INPUT, DOWN); + PIN_SLP(gpk0-6, INPUT, DOWN); + PIN_SLP(gpk0-7, INPUT, DOWN); + + PIN_SLP(gpk1-0, PREV, NONE); + PIN_SLP(gpk1-1, PREV, NONE); + PIN_SLP(gpk1-2, INPUT, DOWN); + PIN_SLP(gpk1-3, PREV, NONE); + PIN_SLP(gpk1-4, PREV, NONE); + PIN_SLP(gpk1-5, PREV, NONE); + PIN_SLP(gpk1-6, PREV, NONE); + + PIN_SLP(gpk2-0, INPUT, DOWN); + PIN_SLP(gpk2-1, INPUT, DOWN); + PIN_SLP(gpk2-2, INPUT, DOWN); + PIN_SLP(gpk2-3, INPUT, DOWN); + PIN_SLP(gpk2-4, INPUT, DOWN); + PIN_SLP(gpk2-5, INPUT, DOWN); + PIN_SLP(gpk2-6, INPUT, DOWN); + + PIN_SLP(gpl0-0, INPUT, DOWN); + PIN_SLP(gpl0-1, INPUT, DOWN); + PIN_SLP(gpl0-2, INPUT, DOWN); + PIN_SLP(gpl0-3, INPUT, DOWN); + + PIN_SLP(gpm0-0, INPUT, DOWN); + PIN_SLP(gpm0-1, INPUT, DOWN); + PIN_SLP(gpm0-2, INPUT, DOWN); + PIN_SLP(gpm0-3, INPUT, DOWN); + PIN_SLP(gpm0-4, INPUT, DOWN); + PIN_SLP(gpm0-5, INPUT, DOWN); + PIN_SLP(gpm0-6, INPUT, DOWN); + PIN_SLP(gpm0-7, INPUT, DOWN); + + PIN_SLP(gpm1-0, INPUT, DOWN); + PIN_SLP(gpm1-1, INPUT, DOWN); + PIN_SLP(gpm1-2, INPUT, DOWN); + PIN_SLP(gpm1-3, INPUT, DOWN); + PIN_SLP(gpm1-4, INPUT, DOWN); + PIN_SLP(gpm1-5, INPUT, DOWN); + PIN_SLP(gpm1-6, INPUT, DOWN); + + PIN_SLP(gpm2-0, INPUT, DOWN); + PIN_SLP(gpm2-1, INPUT, DOWN); + PIN_SLP(gpm2-2, INPUT, DOWN); + PIN_SLP(gpm2-3, INPUT, DOWN); + PIN_SLP(gpm2-4, INPUT, DOWN); + + PIN_SLP(gpm3-0, INPUT, DOWN); + PIN_SLP(gpm3-1, INPUT, DOWN); + PIN_SLP(gpm3-2, INPUT, DOWN); + PIN_SLP(gpm3-3, INPUT, DOWN); + PIN_SLP(gpm3-4, INPUT, DOWN); + PIN_SLP(gpm3-5, INPUT, DOWN); + PIN_SLP(gpm3-6, INPUT, DOWN); + PIN_SLP(gpm3-7, INPUT, DOWN); + + PIN_SLP(gpm4-0, INPUT, DOWN); + PIN_SLP(gpm4-1, INPUT, DOWN); + PIN_SLP(gpm4-2, INPUT, DOWN); + PIN_SLP(gpm4-3, INPUT, DOWN); + PIN_SLP(gpm4-4, INPUT, DOWN); + PIN_SLP(gpm4-5, INPUT, DOWN); + PIN_SLP(gpm4-6, INPUT, DOWN); + PIN_SLP(gpm4-7, INPUT, DOWN); + }; +};
PATCH v2 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
Quoted 2 lines · Chanwoo Choi
Dear Kukjin,
Hi,
Quoted 87 lines
Could you please review or pick this patchset?
Best Regards,
Chanwoo ChoiQuoted 81 lines · YoungJun Cho
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
Changes from v1:
- The 'memory' entries coalesce into one entry
- Removes useless space
- Puts voltage-regulator-0 under the root nodeThis dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power keySigned-off-by Youngjun Cho <[email protected]>Signed-off-by Chanwoo Choi <[email protected]>Signed-off-by Inki Dae <[email protected]>Signed-off-by Seung-Woo Kim <[email protected]>Signed-off-by Jaehoon Chung <[email protected]>Signed-off-by Kyungmin Park <[email protected]>--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 583 ++++++++++++++++++++++++++++++++++ 2 files changed, 585 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dtsarch/arm/boot/dts/Makefile +2
-1@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \arch/arm/boot/dts/exynos3250-monk.dts new file +24
-0@@ -0,0 +1,583 @@ +/* + * Samsung's Exynos3250 based Monk board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Device tree source file for Samsung's Monk board which is based on + * Samsung Exynos3250 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos3250.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung Monk board"; + compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3"; + + aliases { + i2c7 = &i2c_max77836;
Quoted 8 lines
arch/arm/boot/dts/exynos3250-monk.dts line 32
Quoted 8 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +8
-0+ }; + + memory { + reg = <0x40000000 0x1ff00000>; + }; + + chosen { + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";
Actually, the bootargs can be supplied from bootloader and can be removed from here and it's a recent requirement from mailinglist. But I've already applied similar one in rinato.dts. So please cleanup them together later...? :)
[snip]
Will apply, thanks.
- Kukjin
PATCH v2 1/1 ARM: dts: add board dts file for Exynos3250-based Monk board
Quoted 106 lines · Kukjin Kim
Quoted 2 lines · Chanwoo Choi
Dear Kukjin,
Hi,
Quoted 87 lines
Could you please review or pick this patchset?
Best Regards,
Chanwoo ChoiQuoted 81 lines · YoungJun Cho
From: Youngjun Cho <[email protected]>
This patch adds new board dts file to support Samsung Monk board which is based on Exynos3250 SoC and has different H/W configuration from Rinato.
This patch is based on linux-samsung.git for-next branch and depends on [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
Changes from v1:
- The 'memory' entries coalesce into one entry
- Removes useless space
- Puts voltage-regulator-0 under the root nodeThis dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power keySigned-off-by Youngjun Cho <[email protected]>Signed-off-by Chanwoo Choi <[email protected]>Signed-off-by Inki Dae <[email protected]>Signed-off-by Seung-Woo Kim <[email protected]>Signed-off-by Jaehoon Chung <[email protected]>Signed-off-by Kyungmin Park <[email protected]>--- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/exynos3250-monk.dts | 583 ++++++++++++++++++++++++++++++++++ 2 files changed, 585 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/exynos3250-monk.dtsarch/arm/boot/dts/Makefile +2
-1@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb -dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \ +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \ + exynos3250-rinato.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \arch/arm/boot/dts/exynos3250-monk.dts new file +24
-0@@ -0,0 +1,583 @@ +/* + * Samsung's Exynos3250 based Monk board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Device tree source file for Samsung's Monk board which is based on + * Samsung Exynos3250 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos3250.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung Monk board"; + compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3"; + + aliases { + i2c7 = &i2c_max77836;Quoted 8 lines
arch/arm/boot/dts/exynos3250-monk.dts line 32
Quoted 8 lines
arch/arm/boot/dts/exynos3250-monk.dts new file +8
-0+ }; + + memory { + reg = <0x40000000 0x1ff00000>; + }; + + chosen { + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";Actually, the bootargs can be supplied from bootloader and can be removed from here and it's a recent requirement from mailinglist. But I've already applied similar one in
rinato.dts. So please cleanup them together later...? :)
Quoted 5 lines
[snip]
Will apply, thanks.
- Kukjin
I think, you need adding board file description in the Doc?
WARNING: DT compatible string "samsung,monk" appears un-documented -- check ./Documentation/devicetree/bindings/
#79: FILE: arch/arm/boot/dts/exynos3250-monk.dts:21:
+ compatible = "samsung,monk", "samsung,exynos3250", "samsung,exynos3";
Thanks,
Kukjin