Skip to contentSkip to conversation

ASoC: wm8962: Allow codec to work when CONFIG_PM=n

RFC In review Fabio Estevam 2 participants 2 messages Dec 30, 2014

Subsystems (3)
Sound ASoC Wolfson microelectronics drivers
lore
Share & tools
lore

Fabio Estevam

author
#0 lore raw

RFC 1/1 ASoC: wm8962: Allow codec to work when CONFIG_PM=n

From: Fabio Estevam <[email protected]>

Currently the codec does not work in the CONFIG_PM=n case because the regulators and clock are kept disabled.

Allow the codec to be functional by calling wm8962_runtime_resume() when CONFIG_PM=n.

Tested on a imx6sl-evk in the CONFIG_PM=y and CONFIG_PM=n cases.

Signed-off-by Fabio Estevam <[email protected]>

---

Probably there is a better solution, hence I am sending it as RFC.

Thanks

 sound/soc/codecs/wm8962.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
sound/soc/codecs/wm8962.c +8 -2
index d32d554..0b041c9 100644
@@ -3546,6 +3546,9 @@ static int wm8962_set_pdata_from_of(struct i2c_client *i2c,
 	return 0;
 }
 
+static int wm8962_runtime_resume(struct device *dev);
+static int wm8962_runtime_suspend(struct device *dev);
+
 static int wm8962_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {

@@ -3771,6 +3774,9 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 	/* The drivers should power up as needed */
 	regulator_bulk_disable(ARRAY_SIZE(wm8962->supplies), wm8962->supplies);
 
+	if (!IS_ENABLED(CONFIG_PM))
+		wm8962_runtime_resume(&i2c->dev);
+
 	return 0;
 
 err_enable:

@@ -3781,11 +3787,12 @@ err:
 
 static int wm8962_i2c_remove(struct i2c_client *client)
 {
+	if (!IS_ENABLED(CONFIG_PM))
+		wm8962_runtime_suspend(&client->dev);
 	snd_soc_unregister_codec(&client->dev);
 	return 0;
 }
 
-#ifdef CONFIG_PM
 static int wm8962_runtime_resume(struct device *dev)
 {
 	struct wm8962_priv *wm8962 = dev_get_drvdata(dev);

@@ -3860,7 +3867,6 @@ static int wm8962_runtime_suspend(struct device *dev)
 
 	return 0;
 }
-#endif
 
 static struct dev_pm_ops wm8962_pm = {
 	SET_RUNTIME_PM_OPS(wm8962_runtime_suspend, wm8962_runtime_resume, NULL)
Signature · 1 line
1.9.1
maintainer
#1 lore raw

sound/soc/codecs/wm8962.c static int wm8962_i2c_probe(struct i2c_client *i2c, · line 3779

Quoted 3 lines · Fabio Estevam
sound/soc/codecs/wm8962.c +3 -0
+	if (!IS_ENABLED(CONFIG_PM))
+		wm8962_runtime_resume(&i2c->dev);
+

A much neater idiom for this is to have the probe() just default the device to being runtime PM enabled, then if runtime PM is enabled it'll work out that the device is idle and power it off but if runtime PM is disabled it'll just stay powered.