Skip to contentSkip to conversation

usb: dwc3: ep0: preparation for implementing chained TRB

RFC PATCH In review Kishon Vijay Abraham I 2 participants 5 messages Feb 6, 2015 – Jun 1, 2015

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/2 usb: dwc3: ep0: preparation for implementing chained TRB

No functional change. Modified few things so that there are no code duplication while implementing chained TRB.

---
 drivers/usb/dwc3/ep0.c |   23 ++++++++++++++---------
 1 file changed, 14 insertions(+), 9 deletions(-)
drivers/usb/dwc3/ep0.c +14 -9
index 2ef3c8d..24b7925 100644
@@ -779,7 +779,10 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 	struct usb_request	*ur;
 	struct dwc3_trb		*trb;
 	struct dwc3_ep		*ep0;
-	u32			transferred;
+	unsigned		transfer_size = 0;
+	unsigned		maxp;
+	void			*buf;
+	u32			transferred = 0;
 	u32			status;
 	u32			length;
 	u8			epnum;
@@ -808,16 +811,17 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 	}
 
 	ur = &r->request;
+	buf = ur->buf;
 
 	length = trb->size & DWC3_TRB_SIZE_MASK;
 
-	if (dwc->ep0_bounced) {
-		unsigned transfer_size = ur->length;
-		unsigned maxp = ep0->endpoint.maxpacket;
+	maxp = ep0->endpoint.maxpacket;
 
-		transfer_size += (maxp - (transfer_size % maxp));
-		transferred = min_t(u32, ur->length,
-				transfer_size - length);
+	if (dwc->ep0_bounced) {
+		transfer_size = roundup((ur->length - transfer_size),
+					maxp);
+		transferred = min_t(u32, ur->length - transferred,
+				    transfer_size - length);
 		memcpy(ur->buf, dwc->ep0_bounce, transferred);
 	} else {
 		transferred = ur->length - length;
@@ -927,7 +931,7 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 				DWC3_TRBCTL_CONTROL_DATA);
 	} else if (!IS_ALIGNED(req->request.length, dep->endpoint.maxpacket)
 			&& (dep->number == 0)) {
-		u32	transfer_size;
+		u32	transfer_size = 0;
 		u32	maxpacket;
 
 		ret = usb_gadget_map_request(&dwc->gadget, &req->request,
@@ -940,7 +944,8 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 		WARN_ON(req->request.length > DWC3_EP0_BOUNCE_SIZE);
 
 		maxpacket = dep->endpoint.maxpacket;
-		transfer_size = roundup(req->request.length, maxpacket);
+		transfer_size = roundup((req->request.length - transfer_size),
+					maxpacket);
 
 		dwc->ep0_bounced = true;
 
Signature · 1 line
1.7.9.5
#1 lore raw

RFC PATCH 2/2 usb: dwc3: Add chained TRB support for ep0

dwc3 can do only max packet aligned transfers. So in case request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE two chained TRBs is required to handle the transfer.

---
*) Did eumeration testing with g_zero in kernel
*) Similar patch was added in u-boot. With DFU, was able to create a scenario where the request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE (512 bytes). In that case, 2 chained TRBs will be used.

 drivers/usb/dwc3/ep0.c    |   65 +++++++++++++++++++++++++++++++++------------
 drivers/usb/dwc3/gadget.c |    2 +-
 2 files changed, 49 insertions(+), 18 deletions(-)
drivers/usb/dwc3/ep0.c +48 -17
index 24b7925..3b728b8 100644
@@ -56,7 +56,7 @@ static const char *dwc3_ep0_state_string(enum dwc3_ep0_state state)
 }
 
 static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
-		u32 len, u32 type)
+		u32 len, u32 type, unsigned chain)
 {
 	struct dwc3_gadget_ep_cmd_params params;
 	struct dwc3_trb			*trb;
@@ -70,7 +70,10 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
 		return 0;
 	}
 
-	trb = dwc->ep0_trb;
+	trb = &dwc->ep0_trb[dep->free_slot];
+
+	if (chain)
+		dep->free_slot++;
 
 	trb->bpl = lower_32_bits(buf_dma);
 	trb->bph = upper_32_bits(buf_dma);
@@ -78,10 +81,17 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
 	trb->ctrl = type;
 
 	trb->ctrl |= (DWC3_TRB_CTRL_HWO
-			| DWC3_TRB_CTRL_LST
-			| DWC3_TRB_CTRL_IOC
 			| DWC3_TRB_CTRL_ISP_IMI);
 
+	if (chain)
+		trb->ctrl |= DWC3_TRB_CTRL_CHN;
+	else
+		trb->ctrl |= (DWC3_TRB_CTRL_IOC
+				| DWC3_TRB_CTRL_LST);
+
+	if (chain)
+		return 0;
+
 	memset(&params, 0, sizeof(params));
 	params.param0 = upper_32_bits(dwc->ep0_trb_addr);
 	params.param1 = lower_32_bits(dwc->ep0_trb_addr);
@@ -302,7 +312,7 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
 	int				ret;
 
 	ret = dwc3_ep0_start_trans(dwc, 0, dwc->ctrl_req_addr, 8,
-			DWC3_TRBCTL_CONTROL_SETUP);
+			DWC3_TRBCTL_CONTROL_SETUP, false);
 	WARN_ON(ret < 0);
 }
 
@@ -817,6 +827,22 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
 	maxp = ep0->endpoint.maxpacket;
 
+	/* Handle the first TRB before handling the bounce buffer if the request
+	 * length is greater than the bounce buffer size
+	 */
+	if (!IS_ALIGNED(ur->length, maxp) &&
+	    ur->length > DWC3_EP0_BOUNCE_SIZE) {
+		transfer_size = (ur->length / maxp) * maxp;
+		transferred = transfer_size - length;
+		buf = (u8 *)buf + transferred;
+		ur->actual += transferred;
+
+		trb++;
+		length = trb->size & DWC3_TRB_SIZE_MASK;
+
+		ep0->free_slot = 0;
+	}
+
 	if (dwc->ep0_bounced) {
 		transfer_size = roundup((ur->length - transfer_size),
 					maxp);
@@ -844,7 +870,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
 			ret = dwc3_ep0_start_trans(dwc, epnum,
 					dwc->ctrl_req_addr, 0,
-					DWC3_TRBCTL_CONTROL_DATA);
+					DWC3_TRBCTL_CONTROL_DATA, false);
 			WARN_ON(ret < 0);
 		}
 	}
@@ -928,7 +954,7 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 	if (req->request.length == 0) {
 		ret = dwc3_ep0_start_trans(dwc, dep->number,
 				dwc->ctrl_req_addr, 0,
-				DWC3_TRBCTL_CONTROL_DATA);
+				DWC3_TRBCTL_CONTROL_DATA, false);
 	} else if (!IS_ALIGNED(req->request.length, dep->endpoint.maxpacket)
 			&& (dep->number == 0)) {
 		u32	transfer_size = 0;
@@ -941,22 +967,26 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 			return;
 		}
 
-		WARN_ON(req->request.length > DWC3_EP0_BOUNCE_SIZE);
-
 		maxpacket = dep->endpoint.maxpacket;
+
+		if (req->request.length > DWC3_EP0_BOUNCE_SIZE) {
+			transfer_size = (req->request.length / maxpacket) *
+						maxpacket;
+			ret = dwc3_ep0_start_trans(dwc, dep->number,
+						   req->request.dma,
+						   transfer_size,
+						   DWC3_TRBCTL_CONTROL_DATA,
+						   true);
+		}
+
 		transfer_size = roundup((req->request.length - transfer_size),
 					maxpacket);
 
 		dwc->ep0_bounced = true;
 
-		/*
-		 * REVISIT in case request length is bigger than
-		 * DWC3_EP0_BOUNCE_SIZE we will need two chained
-		 * TRBs to handle the transfer.
-		 */
 		ret = dwc3_ep0_start_trans(dwc, dep->number,
 				dwc->ep0_bounce_addr, transfer_size,
-				DWC3_TRBCTL_CONTROL_DATA);
+				DWC3_TRBCTL_CONTROL_DATA, false);
 	} else {
 		ret = usb_gadget_map_request(&dwc->gadget, &req->request,
 				dep->number);
@@ -966,7 +996,8 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 		}
 
 		ret = dwc3_ep0_start_trans(dwc, dep->number, req->request.dma,
-				req->request.length, DWC3_TRBCTL_CONTROL_DATA);
+				req->request.length, DWC3_TRBCTL_CONTROL_DATA,
+				false);
 	}
 
 	WARN_ON(ret < 0);
@@ -981,7 +1012,7 @@ static int dwc3_ep0_start_control_status(struct dwc3_ep *dep)
 		: DWC3_TRBCTL_CONTROL_STATUS2;
 
 	return dwc3_ep0_start_trans(dwc, dep->number,
-			dwc->ctrl_req_addr, 0, type);
+			dwc->ctrl_req_addr, 0, type, false);
 }
 
 static void __dwc3_ep0_do_control_status(struct dwc3 *dwc, struct dwc3_ep *dep)
drivers/usb/dwc3/gadget.c +1 -1
index a03a485..7212b93 100644
@@ -2682,7 +2682,7 @@ int dwc3_gadget_init(struct dwc3 *dwc)
 		goto err0;
 	}
 
-	dwc->ep0_trb = dma_alloc_coherent(dwc->dev, sizeof(*dwc->ep0_trb),
+	dwc->ep0_trb = dma_alloc_coherent(dwc->dev, sizeof(*dwc->ep0_trb) * 2,
 			&dwc->ep0_trb_addr, GFP_KERNEL);
 	if (!dwc->ep0_trb) {
 		dev_err(dwc->dev, "failed to allocate ep0 trb\n");
Signature · 1 line
1.7.9.5
#2 lore raw

Re: [RFC PATCH 2/2] usb: dwc3: Add chained TRB support for ep0

Hi,

Quoted 10 lines · Kishon Vijay Abraham I

dwc3 can do only max packet aligned transfers. So in case request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE two chained TRBs is required to handle the transfer.

---
*) Did eumeration testing with g_zero in kernel
*) Similar patch was added in u-boot. With DFU, was able to create a scenario where the request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE (512 bytes). In that case, 2 chained TRBs will be used.

I really need a test case for this. If you have to patch g_zero to have a configuration descriptor so large that it's over 512, so be it, but I really need to have a test case exposing the problem.

I also need you to run full USB30CV (for USB2 and USB3 device), together with Link Layer Tests (on USB3-only, clearly) using USB30CV and LeCroy's compliance suite (there's a slight difference from USB30CV and LeCroy's compliance, we must work with both because both are accepted test vectors per USB-IF).

Quoted 55 lines
drivers/usb/dwc3/ep0.c +15 -5
index 24b7925..3b728b8 100644
@@ -56,7 +56,7 @@ static const char *dwc3_ep0_state_string(enum dwc3_ep0_state state)
 }
 
 static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
-		u32 len, u32 type)
+		u32 len, u32 type, unsigned chain)
 {
 	struct dwc3_gadget_ep_cmd_params params;
 	struct dwc3_trb			*trb;
@@ -70,7 +70,10 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
 		return 0;
 	}
 
-	trb = dwc->ep0_trb;
+	trb = &dwc->ep0_trb[dep->free_slot];
+
+	if (chain)
+		dep->free_slot++;
 
 	trb->bpl = lower_32_bits(buf_dma);
 	trb->bph = upper_32_bits(buf_dma);
@@ -78,10 +81,17 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
 	trb->ctrl = type;
 
 	trb->ctrl |= (DWC3_TRB_CTRL_HWO
-			| DWC3_TRB_CTRL_LST
-			| DWC3_TRB_CTRL_IOC
 			| DWC3_TRB_CTRL_ISP_IMI);
 
+	if (chain)
+		trb->ctrl |= DWC3_TRB_CTRL_CHN;
+	else
+		trb->ctrl |= (DWC3_TRB_CTRL_IOC
+				| DWC3_TRB_CTRL_LST);
+
+	if (chain)
+		return 0;
+
 	memset(&params, 0, sizeof(params));
 	params.param0 = upper_32_bits(dwc->ep0_trb_addr);
 	params.param1 = lower_32_bits(dwc->ep0_trb_addr);
@@ -302,7 +312,7 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
 	int				ret;
 
 	ret = dwc3_ep0_start_trans(dwc, 0, dwc->ctrl_req_addr, 8,
-			DWC3_TRBCTL_CONTROL_SETUP);
+			DWC3_TRBCTL_CONTROL_SETUP, false);
 	WARN_ON(ret < 0);
 }
 

drivers/usb/dwc3/ep0.c static void dwc3_ep0_complete_data(struct dwc3 *dwc, · line 835

Quoted 9 lines
drivers/usb/dwc3/ep0.c +6 -0
@@ -817,6 +827,22 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
 	maxp = ep0->endpoint.maxpacket;
 
+	/* Handle the first TRB before handling the bounce buffer if the request
+	 * length is greater than the bounce buffer size
+	 */
+	if (!IS_ALIGNED(ur->length, maxp) &&
+	    ur->length > DWC3_EP0_BOUNCE_SIZE) {
+		transfer_size = (ur->length / maxp) * maxp;

you can use ALIGN() for this which is more efficient. Note however that this is not safe, see below.

drivers/usb/dwc3/ep0.c static void dwc3_ep0_complete_data(struct dwc3 *dwc, · line 838

Quoted 3 lines
drivers/usb/dwc3/ep0.c +3 -0
+		transferred = transfer_size - length;
+		buf = (u8 *)buf + transferred;
+		ur->actual += transferred;

this is dangerous. The extra size is because you *must* align OUT to wMaxPacketSize, so you cannot allow more than the original req->length to be copied into buf. That bounce buffer, is really supposed to be a throw-away buffer and should never have data in it. You should really add a big fat WARN() if transferred > req->length.

The thing is that if host sends more data than we were expecting, this could be someone trying to use our driver as an exploit vector, trying to send more data than it should. We must be robust against that.

Quoted 34 lines
drivers/usb/dwc3/ep0.c +9 -4
+
+		trb++;
+		length = trb->size & DWC3_TRB_SIZE_MASK;
+
+		ep0->free_slot = 0;
+	}
+
 	if (dwc->ep0_bounced) {
 		transfer_size = roundup((ur->length - transfer_size),
 					maxp);
@@ -844,7 +870,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
 			ret = dwc3_ep0_start_trans(dwc, epnum,
 					dwc->ctrl_req_addr, 0,
-					DWC3_TRBCTL_CONTROL_DATA);
+					DWC3_TRBCTL_CONTROL_DATA, false);
 			WARN_ON(ret < 0);
 		}
 	}
@@ -928,7 +954,7 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 	if (req->request.length == 0) {
 		ret = dwc3_ep0_start_trans(dwc, dep->number,
 				dwc->ctrl_req_addr, 0,
-				DWC3_TRBCTL_CONTROL_DATA);
+				DWC3_TRBCTL_CONTROL_DATA, false);
 	} else if (!IS_ALIGNED(req->request.length, dep->endpoint.maxpacket)
 			&& (dep->number == 0)) {
 		u32	transfer_size = 0;
@@ -941,22 +967,26 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
 			return;
 		}
 
-		WARN_ON(req->request.length > DWC3_EP0_BOUNCE_SIZE);
-

drivers/usb/dwc3/ep0.c static void __dwc3_ep0_do_control_data(struct dwc3 *dwc, · line 979

Quoted 10 lines
drivers/usb/dwc3/ep0.c +9 -0
 		maxpacket = dep->endpoint.maxpacket;
+
+		if (req->request.length > DWC3_EP0_BOUNCE_SIZE) {
+			transfer_size = (req->request.length / maxpacket) *
+						maxpacket;
+			ret = dwc3_ep0_start_trans(dwc, dep->number,
+						   req->request.dma,
+						   transfer_size,
+						   DWC3_TRBCTL_CONTROL_DATA,
+						   true);

I would prefer to split this even further. First add the new chain parameter, then make use of it. This means that anywhere chain is false, would not be part of $subject.

Signature · 1 line
balbi
#3 lore raw

Re: [RFC PATCH 2/2] usb: dwc3: Add chained TRB support for ep0

Hi Felipe,

Quoted 14 lines · Felipe Balbi

Hi,

Quoted 10 lines · Kishon Vijay Abraham I

dwc3 can do only max packet aligned transfers. So in case request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE two chained TRBs is required to handle the transfer.

---
*) Did eumeration testing with g_zero in kernel
*) Similar patch was added in u-boot. With DFU, was able to create a scenario where the request length is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE (512 bytes). In that case, 2 chained TRBs will be used.

Quoted 3 lines

I really need a test case for this. If you have to patch g_zero to have a configuration descriptor so large that it's over 512, so be it, but I really need to have a test case exposing the problem.

sure.

Quoted 6 lines

I also need you to run full USB30CV (for USB2 and USB3 device), together with Link Layer Tests (on USB3-only, clearly) using USB30CV and LeCroy's compliance suite (there's a slight difference from USB30CV and LeCroy's compliance, we must work with both because both are accepted test vectors per USB-IF).

sure.

Quoted 59 lines
Quoted 59 lines
drivers/usb/dwc3/ep0.c +15 -5
index 24b7925..3b728b8 100644
@@ -56,7 +56,7 @@ static const char *dwc3_ep0_state_string(enum dwc3_ep0_state state)
  }
 
  static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
-		u32 len, u32 type)
+		u32 len, u32 type, unsigned chain)
  {
  	struct dwc3_gadget_ep_cmd_params params;
  	struct dwc3_trb			*trb;
@@ -70,7 +70,10 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
  		return 0;
  	}
 
-	trb = dwc->ep0_trb;
+	trb = &dwc->ep0_trb[dep->free_slot];
+
+	if (chain)
+		dep->free_slot++;
 
  	trb->bpl = lower_32_bits(buf_dma);
  	trb->bph = upper_32_bits(buf_dma);
@@ -78,10 +81,17 @@ static int dwc3_ep0_start_trans(struct dwc3 *dwc, u8 epnum, dma_addr_t buf_dma,
  	trb->ctrl = type;
 
  	trb->ctrl |= (DWC3_TRB_CTRL_HWO
-			| DWC3_TRB_CTRL_LST
-			| DWC3_TRB_CTRL_IOC
  			| DWC3_TRB_CTRL_ISP_IMI);
 
+	if (chain)
+		trb->ctrl |= DWC3_TRB_CTRL_CHN;
+	else
+		trb->ctrl |= (DWC3_TRB_CTRL_IOC
+				| DWC3_TRB_CTRL_LST);
+
+	if (chain)
+		return 0;
+
  	memset(&params, 0, sizeof(params));
  	params.param0 = upper_32_bits(dwc->ep0_trb_addr);
  	params.param1 = lower_32_bits(dwc->ep0_trb_addr);
@@ -302,7 +312,7 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
  	int				ret;
 
  	ret = dwc3_ep0_start_trans(dwc, 0, dwc->ctrl_req_addr, 8,
-			DWC3_TRBCTL_CONTROL_SETUP);
+			DWC3_TRBCTL_CONTROL_SETUP, false);
  	WARN_ON(ret < 0);
  }
 
@@ -817,6 +827,22 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
  	maxp = ep0->endpoint.maxpacket;
 
Quoted 9 lines

drivers/usb/dwc3/ep0.c static void dwc3_ep0_complete_data(struct dwc3 *dwc, · line 835

Quoted 6 lines
drivers/usb/dwc3/ep0.c +6 -0
+	/* Handle the first TRB before handling the bounce buffer if the request
+	 * length is greater than the bounce buffer size
+	 */
+	if (!IS_ALIGNED(ur->length, maxp) &&
+	    ur->length > DWC3_EP0_BOUNCE_SIZE) {
+		transfer_size = (ur->length / maxp) * maxp;

you can use ALIGN() for this which is more efficient. Note however that this is not safe, see below.

right, I can achieve the same using ALIGN(ur->length - maxp, maxp);

Quoted 8 lines

drivers/usb/dwc3/ep0.c static void dwc3_ep0_complete_data(struct dwc3 *dwc, · line 838

Quoted 4 lines
drivers/usb/dwc3/ep0.c +3 -0
+		transferred = transfer_size - length;
+		buf = (u8 *)buf + transferred;
+		ur->actual += transferred;

this is dangerous. The extra size is because you *must* align OUT to wMaxPacketSize, so you cannot allow more than the original req->length to be copied into buf. That bounce buffer, is really supposed to be a

Here we are not handling bounce buffer. The bounce buffer is used only for the 2nd TRB which actually programs to receive data that is less than bounce buffer size. The 1st TRB will always be max packet aligned and the data is directly copied to the request buffer. (However note that if the request length is less than bounce buffer size, we'll use 1 TRB only)

To summarize..
We are splitting req->length into 2 TRB's if the req->length is not aligned to wMaxPacketSize _and_ req->length is greater than bounce buffer size. By this way we can make the 2nd TRB to receive data lesser than or equal to bounce buffer size and the rest of it can be received using the 1st TRB.

Consider the following case.
ur->length = 612;
maxp = 512;

This case can't be handled by the existing bounce buffer mechanism since the size of bounce buffer is only 512. So we program 2 TRB's. First TRB
trb->size = 512; /* We don't need bounce buffer for this TRB since it is max packet aligned. The data is directly loaded to the request buffer. */

Second TRB
trb->size = 512 /* For the remaining 100 bytes we use bounce buffer and it uses the same existing bounce buffer mechanism. But instead of copying the data to the start of the request buffer, it has to be appended to the data that is received due to first TRB. */

Quoted 6 lines

throw-away buffer and should never have data in it. You should really add a big fat WARN() if transferred > req->length.

The thing is that if host sends more data than we were expecting, this could be someone trying to use our driver as an exploit vector, trying to send more data than it should. We must be robust against that.

This is handled in the existing bounce buffer mechanism and I use the same bounce buffer mechanism for the 2nd TRB.

Quoted 33 lines
Quoted 33 lines
drivers/usb/dwc3/ep0.c +9 -2
+
+		trb++;
+		length = trb->size & DWC3_TRB_SIZE_MASK;
+
+		ep0->free_slot = 0;
+	}
+
  	if (dwc->ep0_bounced) {
  		transfer_size = roundup((ur->length - transfer_size),
  					maxp);
@@ -844,7 +870,7 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc,
 
  			ret = dwc3_ep0_start_trans(dwc, epnum,
  					dwc->ctrl_req_addr, 0,
-					DWC3_TRBCTL_CONTROL_DATA);
+					DWC3_TRBCTL_CONTROL_DATA, false);
  			WARN_ON(ret < 0);
  		}
  	}
@@ -928,7 +954,7 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
  	if (req->request.length == 0) {
  		ret = dwc3_ep0_start_trans(dwc, dep->number,
  				dwc->ctrl_req_addr, 0,
-				DWC3_TRBCTL_CONTROL_DATA);
+				DWC3_TRBCTL_CONTROL_DATA, false);
  	} else if (!IS_ALIGNED(req->request.length, dep->endpoint.maxpacket)
  			&& (dep->number == 0)) {
  		u32	transfer_size = 0;
@@ -941,22 +967,26 @@ static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
  			return;
  		}
 
Quoted 16 lines

drivers/usb/dwc3/ep0.c static void __dwc3_ep0_do_control_data(struct dwc3 *dwc, · line 979

Quoted 12 lines
drivers/usb/dwc3/ep0.c +9 -2
-		WARN_ON(req->request.length > DWC3_EP0_BOUNCE_SIZE);
-
  		maxpacket = dep->endpoint.maxpacket;
+
+		if (req->request.length > DWC3_EP0_BOUNCE_SIZE) {
+			transfer_size = (req->request.length / maxpacket) *
+						maxpacket;
+			ret = dwc3_ep0_start_trans(dwc, dep->number,
+						   req->request.dma,
+						   transfer_size,
+						   DWC3_TRBCTL_CONTROL_DATA,
+						   true);

I would prefer to split this even further. First add the new chain parameter, then make use of it. This means that anywhere chain is false, would not be part of $subject.

Sure.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

#4 lore raw

Re: [RFC PATCH 2/2] usb: dwc3: Add chained TRB support for ep0

Hi,

Quoted 30 lines · Kishon Vijay Abraham I
Quoted 7 lines

drivers/usb/dwc3/ep0.c static void dwc3_ep0_complete_data(struct dwc3 *dwc, · line 838

Quoted 3 lines
drivers/usb/dwc3/ep0.c +3 -0
+		transferred = transfer_size - length;
+		buf = (u8 *)buf + transferred;
+		ur->actual += transferred;

this is dangerous. The extra size is because you *must* align OUT to wMaxPacketSize, so you cannot allow more than the original req->length to be copied into buf. That bounce buffer, is really supposed to be a

Here we are not handling bounce buffer. The bounce buffer is used only for the 2nd TRB which actually programs to receive data that is less than bounce buffer size. The 1st TRB will always be max packet aligned and the data is directly copied to the request buffer. (However note that if the request length is less than bounce buffer size, we'll use 1 TRB only)

To summarize..
We are splitting req->length into 2 TRB's if the req->length is not aligned to wMaxPacketSize _and_ req->length is greater than bounce buffer size. By this way we can make the 2nd TRB to receive data lesser than or equal to bounce buffer size and the rest of it can be received using the 1st TRB.

Consider the following case.
ur->length = 612;
maxp = 512;

This case can't be handled by the existing bounce buffer mechanism since the size of bounce buffer is only 512. So we program 2 TRB's.
First TRB
trb->size = 512; /* We don't need bounce buffer for this TRB since it is max packet aligned. The data is directly loaded to the request buffer. */

Quoted 5 lines

Second TRB
trb->size = 512 /* For the remaining 100 bytes we use bounce buffer and it uses the same existing bounce buffer mechanism. But instead of copying the data to the start of the request buffer, it has to be appended to the data that is received due to first TRB. */

this is all fine, but you need to make sure that you only copy the remaining 100 bytes. Never, ever, ever copy anything past that.

Quoted 9 lines
Quoted 6 lines

throw-away buffer and should never have data in it. You should really add a big fat WARN() if transferred > req->length.

The thing is that if host sends more data than we were expecting, this could be someone trying to use our driver as an exploit vector, trying to send more data than it should. We must be robust against that.

This is handled in the existing bounce buffer mechanism and I use the same bounce buffer mechanism for the 2nd TRB.

ok.

Signature · 1 line
balbi