Skip to contentSkip to conversation

thermal: Add qcom tsens thermal sensor driver

PATCH Superseded Narendran Rajan 3 participants 4 messages Feb 5, 2015 – Feb 23, 2015

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 thermal: Add qcom tsens thermal sensor driver

This version of patch incorporates several review comments from community (Srini, Leena, Stephen, Eduardo).

Main changes compared to v1 are the following:
- Removed HW trip mode specific code as this is not preset in upstream
- Removed interrupts support. Not needed as the thermal framework uses polling method
- Made it a generic qcom tsens driver (name changes throughout)
- Made tsens device a subnode of gcc
- Leveraged patches from Srini for qfprom access and making it gcc subnode
- Uses SIMPLE_DEV_PM_OPS
- Bug fixes, clean up as pointed out in the reviews
- Combined dt documentation along with the driver

This patch has dependency on following patches published in the mailing list

https://patchwork.kernel.org/patch/5748661/
https://patchwork.kernel.org/patch/5748681/

https://patchwork.kernel.org/patch/5707771/
https://patchwork.kernel.org/patch/5707781/

Narendran Rajan (1):
thermal: Add qcom tsens thermal sensor driver

 .../devicetree/bindings/thermal/qcom-thermal.txt   |  59 +++
 drivers/thermal/Kconfig                            |  14 +
 drivers/thermal/Makefile                           |   1 +
 drivers/thermal/qcom-tsens.c                       | 498 +++++++++++++++++++++
 4 files changed, 572 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/qcom-thermal.txt
 create mode 100644 drivers/thermal/qcom-tsens.c

--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project

#1 lore raw

PATCH v2 1/1 thermal: Add qcom tsens thermal sensor driver

TSENS supports reading temperature from multiple thermal sensors present in QCOM SOCs.
TSENS HW is enabled only when the main sensor is requested. TSENS block is disabled if the main senors is disabled irrespective of any other sensors that are being enabled

The driver needs calibration data which is read from qfprom. Calibration data location is configured through dt files.

Based on code by Siddartha Mohanadoss and Stephen Boyd.

Cc Siddartha Mohanadoss <[email protected]>
Cc Stephen Boyd <[email protected]>
---
 .../devicetree/bindings/thermal/qcom-thermal.txt   |  59 +++
 drivers/thermal/Kconfig                            |  14 +
 drivers/thermal/Makefile                           |   1 +
 drivers/thermal/qcom-tsens.c                       | 498 +++++++++++++++++++++
 4 files changed, 572 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/qcom-thermal.txt
 create mode 100644 drivers/thermal/qcom-tsens.c
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +59 -0
new file mode 100644
index 0000000..c8ab66b
@@ -0,0 +1,59 @@
+* QCOM SoC Temperature Sensor (TSENS)
+
+Required properties:
+- compatible : "qcom,qcom-tsens"
+- qcom,tsens-slopes : Must contain slope value for each of the sensors controlled
+			by this device
+- qcom,qfprom : An arry of triplets containing tsens calibration data.
+		The first element in the triplet is a phandle
+                to qfprom compatible node, second element is a offset to calibration
+                data within this node, third element indicates size of calibration
+                data.
+                In general, there would be two elements in this array
+                - first containing information on primary calibration data
+                - second containing information on backup calibration data
+- qcom,qfprom-names : Names for each calibration data
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+
+Exiample:
+tsens: tsens-qcom {
+		compatible = "qcom,qcom-tsens";
+		qcom,tsens-slopes = <1176 1176 1154 1176 1111
+				1132 1132 1199 1132 1199
+				1132>;
+		qcom,qfprom = <&imem 0x400 11>, <&imem 0x410 11>;
+		qcom,qfprom-names = "calib", "backup_calib";
+		#thermal-sensor-cells = <1>;
+	};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsens	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <80000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <120000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+					<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
drivers/thermal/Kconfig +14 -0
index 20915ca..c085405 100644
@@ -261,6 +261,20 @@ config INTEL_SOC_DTS_THERMAL
 	  notification methods.The other trip is a critical trip point, which
 	  was set by the driver based on the TJ MAX temperature.
 
+config THERMAL_QCOMTSENS
+	tristate "Qualcomm Tsens Temperature driver"
+	depends on THERMAL
+	depends on ARCH_QCOM
+	help
+	  QCOM tsens thermal driver provides support for Temperature sensor
+	  (TSENS) found on QCOM SoCs. It supports four configurable trip points
+	  and controls multiple sensors on the SOC. The four trip points are
+	  common across all sensors present in the SoC. The number of sensors
+	  present vary from chip to chip and are set through device tree entry.
+	  The driver presents as a standard thermal zone device with configurable
+	  trip points and cooling device mapping through standard thermal zone
+	  device tree
+
 menu "ACPI INT340X thermal drivers"
 source drivers/thermal/int340x_thermal/Kconfig
 endmenu
drivers/thermal/Makefile +1 -0
index fa0dc48..3fdf6b9 100644
@@ -39,3 +39,4 @@ obj-$(CONFIG_TI_SOC_THERMAL)	+= ti-soc-thermal/
 obj-$(CONFIG_INT340X_THERMAL)  += int340x_thermal/
 obj-$(CONFIG_ST_THERMAL)	+= st/
 obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
+obj-$(CONFIG_THERMAL_QCOMTSENS)	+= qcom-tsens.o
drivers/thermal/qcom-tsens.c new file +498 -0

498 lines not on this page · raw message

Signature · 1 line
Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
#2 lore raw
Quoted 14 lines · Narendran Rajan

TSENS supports reading temperature from multiple thermal sensors present in QCOM SOCs.
TSENS HW is enabled only when the main sensor is requested. TSENS block is disabled if the main senors is disabled irrespective of any other sensors that are being enabled

The driver needs calibration data which is read from qfprom. Calibration data location is configured through dt files.

Based on code by Siddartha Mohanadoss and Stephen Boyd.

Cc Siddartha Mohanadoss <[email protected]>
Cc Stephen Boyd <[email protected]>
Quoted 8 lines

---

.../devicetree/bindings/thermal/qcom-thermal.txt   |  59 +++
drivers/thermal/Kconfig                            |  14 +
drivers/thermal/Makefile                           |   1 +
drivers/thermal/qcom-tsens.c                       | 498 +++++++++++++++++++++
4 files changed, 572 insertions(+)

create mode 100644 Documentation/devicetree/bindings/thermal/qcom-thermal.txt create mode 100644 drivers/thermal/qcom-tsens.c

Why is the devicetree nodes not part of the series. Without the devicetree this driver does not provide any functionality on the SoC.

Consider supporting 8084,8074,8064, 8016 as part of this series.

Quoted 7 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +0 -0
new file mode 100644
index 0000000..c8ab66b

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 7

Quoted 7 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +7 -0
@@ -0,0 +1,59 @@
+* QCOM SoC Temperature Sensor (TSENS)
+
+Required properties:
+- compatible : "qcom,qcom-tsens"
+- qcom,tsens-slopes : Must contain slope value for each of the sensors controlled
+			by this device
+- qcom,qfprom : An arry of triplets containing tsens calibration data.

/s/arry/array

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 9

Quoted 2 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +2 -0
+		The first element in the triplet is a phandle
+                to qfprom compatible node, second element is a offset to calibration

s/a offset/an offset

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 18

Quoted 9 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +9 -0
+                data within this node, third element indicates size of calibration
+                data.
+                In general, there would be two elements in this array
+                - first containing information on primary calibration data
+                - second containing information on backup calibration data
+- qcom,qfprom-names : Names for each calibration data
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+
+Exiample:

Example

Quoted 46 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +41 -0
+tsens: tsens-qcom {
+		compatible = "qcom,qcom-tsens";
+		qcom,tsens-slopes = <1176 1176 1154 1176 1111
+				1132 1132 1199 1132 1199
+				1132>;
+		qcom,qfprom = <&imem 0x400 11>, <&imem 0x410 11>;
+		qcom,qfprom-names = "calib", "backup_calib";
+		#thermal-sensor-cells = <1>;
+	};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsens	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <80000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <120000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+					<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
drivers/thermal/Kconfig +0 -0
index 20915ca..c085405 100644

drivers/thermal/Kconfig config INTEL_SOC_DTS_THERMAL · line 264

Quoted 4 lines
drivers/thermal/Kconfig +1 -0
@@ -261,6 +261,20 @@ config INTEL_SOC_DTS_THERMAL
 	  notification methods.The other trip is a critical trip point, which
 	  was set by the driver based on the TJ MAX temperature.
 
+config THERMAL_QCOMTSENS

THERMAL_QCOM_TSENS

Quoted 93 lines
drivers/thermal/Kconfig +13 -0
+	tristate "Qualcomm Tsens Temperature driver"
+	depends on THERMAL
+	depends on ARCH_QCOM
+	help
+	  QCOM tsens thermal driver provides support for Temperature sensor
+	  (TSENS) found on QCOM SoCs. It supports four configurable trip points
+	  and controls multiple sensors on the SOC. The four trip points are
+	  common across all sensors present in the SoC. The number of sensors
+	  present vary from chip to chip and are set through device tree entry.
+	  The driver presents as a standard thermal zone device with configurable
+	  trip points and cooling device mapping through standard thermal zone
+	  device tree
+

menu "ACPI INT340X thermal drivers"
source drivers/thermal/int340x_thermal/Kconfig
endmenu

drivers/thermal/Makefile +0 -0
index fa0dc48..3fdf6b9 100644
@@ -39,3 +39,4 @@ obj-$(CONFIG_TI_SOC_THERMAL)	+= ti-soc-thermal/

obj-$(CONFIG_INT340X_THERMAL) += int340x_thermal/
obj-$(CONFIG_ST_THERMAL) += st/
obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o

drivers/thermal/Makefile +1 -0
+obj-$(CONFIG_THERMAL_QCOMTSENS)	+= qcom-tsens.o
drivers/thermal/qcom-tsens.c new file +62 -0
new file mode 100644
index 0000000..a794961
@@ -0,0 +1,498 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/pm.h>
+#include <linux/bitops.h>
+#include <linux/regmap.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <soc/qcom/qfprom.h>
+
+#define TSENS_CAL_MDEGC				30000
+
+#define TSENS_8960_CONFIG_ADDR			0x3640
+#define TSENS_8960_CONFIG			0x9b
+#define TSENS_8960_CONFIG_MASK			0xf
+
+#define TSENS_CNTL_ADDR				0x3620
+#define TSENS_EN				BIT(0)
+#define TSENS_SW_RST				BIT(1)
+#define SENSOR0_EN				BIT(3)
+#define TSENS_MIN_STATUS_MASK			BIT(0)
+#define TSENS_LOWER_STATUS_CLR			BIT(1)
+#define TSENS_UPPER_STATUS_CLR			BIT(2)
+#define TSENS_MAX_STATUS_MASK			BIT(3)
+#define TSENS_8960_MEASURE_PERIOD		BIT(18)
+#define TSENS_8660_MEASURE_PERIOD		BIT(16)
+#define TSENS_8960_SLP_CLK_ENA			BIT(26)
+#define TSENS_8660_SLP_CLK_ENA			BIT(24)
+#define TSENS_8064_STATUS_CNTL			0x3660
+
+#define TSENS_THRESHOLD_ADDR			0x3624
+#define TSENS_THRESHOLD_MAX_CODE		0xff
+#define TSENS_THRESHOLD_MIN_CODE		0
+#define TSENS_THRESHOLD_MAX_LIMIT_SHIFT		24
+#define TSENS_THRESHOLD_MIN_LIMIT_SHIFT		16
+#define TSENS_THRESHOLD_UPPER_LIMIT_SHIFT	8
+#define TSENS_THRESHOLD_LOWER_LIMIT_SHIFT	0
+
+/* Initial temperature threshold values */
+#define TSENS_LOWER_LIMIT_TH			0x50
+#define TSENS_UPPER_LIMIT_TH			0xdf
+#define TSENS_MIN_LIMIT_TH			0x0
+#define TSENS_MAX_LIMIT_TH			0xff
+
+#define TSENS_S0_STATUS_ADDR			0x3628

drivers/thermal/qcom-tsens.c line 72

Quoted 10 lines
drivers/thermal/qcom-tsens.c new file +10 -0
+
+#define TSENS_INT_STATUS_ADDR			0x363c
+#define TSENS_TRDY_MASK				BIT(7)
+
+#define TSENS_SENSOR0_SHIFT			3
+
+#define TSENS_8660_CONFIG			1
+#define TSENS_8660_CONFIG_SHIFT			28
+#define TSENS_8660_CONFIG_MASK			(3 << TSENS_8660_CONFIG_SHIFT)
+#define TSENS_SENSORABOVEFIVE_OFFSET		40

Needs alignment.

Quoted 251 lines
drivers/thermal/qcom-tsens.c new file +251 -0
+
+struct tsens_device;
+
+struct tsens_sensor {
+	struct thermal_zone_device	*tz_dev;
+	enum thermal_device_mode	mode;
+	unsigned int			sensor_num;
+	int				offset;
+	int				slope;
+	struct tsens_device		*tmdev;
+	u32                             status;
+};
+
+struct tsens_device {
+	struct device		*dev;
+	bool			prev_reading_avail;
+	unsigned int		num_sensors;
+	int			pm_tsens_thr_data;
+	int			pm_tsens_cntl;
+	struct regmap		*map;
+	struct regmap_field	*status_field;
+	struct tsens_sensor	sensor[0];
+};
+
+/* Temperature on y axis and ADC-code on x-axis */
+static int
+tsens_tz_code_to_mdegC(u32 adc_code, const struct tsens_sensor *s)
+{
+	return adc_code * s->slope + s->offset;
+}
+
+static int tsens_tz_get_temp(void *_sensor,
+			     long *temp)
+{
+	const struct tsens_sensor *tm_sensor = _sensor;
+	struct tsens_device *tmdev = tm_sensor->tmdev;
+	u32 code, trdy;
+
+	if (tm_sensor->mode != THERMAL_DEVICE_ENABLED)
+		return -EINVAL;
+
+	if (!tmdev->prev_reading_avail) {
+		while (!regmap_read(tmdev->map, TSENS_INT_STATUS_ADDR, &trdy) &&
+		       !(trdy & TSENS_TRDY_MASK))
+			usleep_range(1000, 1100);
+		tmdev->prev_reading_avail = true;
+	}
+
+	regmap_read(tmdev->map, tm_sensor->status, &code);
+	*temp = tsens_tz_code_to_mdegC(code, tm_sensor);
+
+	dev_dbg(tmdev->dev, "Sensor %d temp is: %ld",
+		tm_sensor->sensor_num, *temp);
+	return 0;
+}
+
+/*
+ * If the main sensor is disabled all the sensors are disable and
+ * the clock is disabled.
+ * If the main sensor is disabled and a sub-sensor is enabled
+ * return with an error.
+ */
+static int tsens_tz_set_mode(struct tsens_sensor *tm_sensor,
+			      enum thermal_device_mode mode)
+{
+	struct tsens_device *tmdev = tm_sensor->tmdev;
+	unsigned int i, n = tmdev->num_sensors;
+	u32 reg, mask;
+
+	if (mode == tm_sensor->mode)
+		return 0;
+
+	regmap_read(tmdev->map, TSENS_CNTL_ADDR, &reg);
+
+	mask = BIT(tm_sensor->sensor_num + TSENS_SENSOR0_SHIFT);
+	if (mode == THERMAL_DEVICE_ENABLED) {
+		if (!(reg & SENSOR0_EN) && mask != SENSOR0_EN) {
+			dev_warn(tmdev->dev, "Main sensor not enabled\n");
+			return -EINVAL;
+		}
+
+		regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg | TSENS_SW_RST);
+		if (tmdev->num_sensors > 1)
+			reg |= mask | TSENS_8960_SLP_CLK_ENA | TSENS_EN;
+		else
+			reg |= mask | TSENS_8660_SLP_CLK_ENA | TSENS_EN;
+		tmdev->prev_reading_avail = false;
+	} else {
+		reg &= ~mask;
+		if (!(reg & SENSOR0_EN)) {
+			dev_warn(tmdev->dev, "Main sensor not enabled. Disabling subsensors\n");
+
+			reg &= ~GENMASK(n + TSENS_SENSOR0_SHIFT - 1,
+					TSENS_SENSOR0_SHIFT);
+			reg &= ~TSENS_EN;
+
+			if (tmdev->num_sensors > 1)
+				reg &= ~TSENS_8960_SLP_CLK_ENA;
+			else
+				reg &= ~TSENS_8660_SLP_CLK_ENA;
+
+			/* Disable all sub-sensors */
+			for (i = 1; i < n; i++)
+				tmdev->sensor[i].mode = mode;
+		}
+	}
+
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg);
+	tm_sensor->mode = mode;
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int tsens_suspend(struct device *dev)
+{
+	int i;
+	unsigned int mask;
+	struct tsens_device *tmdev = dev_get_drvdata(dev);
+	struct regmap *map = tmdev->map;
+
+	regmap_read(map, TSENS_THRESHOLD_ADDR, &tmdev->pm_tsens_thr_data);
+	regmap_read(map, TSENS_CNTL_ADDR, &tmdev->pm_tsens_cntl);
+
+	if (tmdev->num_sensors > 1)
+		mask = TSENS_8960_SLP_CLK_ENA | TSENS_EN;
+	else
+		mask = TSENS_8660_SLP_CLK_ENA | TSENS_EN;
+
+	regmap_update_bits(map, TSENS_CNTL_ADDR, mask, 0);
+
+	tmdev->prev_reading_avail = 0;
+	for (i = 0; i < tmdev->num_sensors; i++)
+		tmdev->sensor[i].mode = THERMAL_DEVICE_DISABLED;
+
+	return 0;
+}
+
+static int tsens_resume(struct device *dev)
+{
+	int i;
+	unsigned long reg_cntl;
+	struct tsens_device *tmdev = dev_get_drvdata(dev);
+	struct regmap *map = tmdev->map;
+
+	regmap_update_bits(map, TSENS_CNTL_ADDR, TSENS_SW_RST, TSENS_SW_RST);
+	regmap_field_update_bits(tmdev->status_field,
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK,
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK);
+
+	/*
+	* Separate CONFIG restore is needed only for 8960. For 8660
+	* config is part of CTRL Addr and its restored as such
+	*/
+	if (tmdev->num_sensors > 1)
+		regmap_update_bits(map, TSENS_8960_CONFIG_ADDR,
+				TSENS_8960_CONFIG_MASK,
+				TSENS_8960_CONFIG);
+
+	regmap_write(map, TSENS_THRESHOLD_ADDR, tmdev->pm_tsens_thr_data);
+	regmap_write(map, TSENS_CNTL_ADDR, tmdev->pm_tsens_cntl);
+
+	reg_cntl = tmdev->pm_tsens_cntl;
+	reg_cntl >>= TSENS_SENSOR0_SHIFT;
+	for_each_set_bit(i, &reg_cntl, tmdev->num_sensors)
+		tmdev->sensor[i].mode = THERMAL_DEVICE_ENABLED;
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(tsens_pm_ops, tsens_suspend, tsens_resume);
+#define TSENS_PM_OPS	(&tsens_pm_ops)
+
+#else /* CONFIG_PM_SLEEP */
+
+#define TSENS_PM_OPS	NULL
+
+#endif /* CONFIG_PM_SLEEP */
+
+static void tsens_disable_mode(const struct tsens_device *tmdev)
+{
+	u32 reg_cntl;
+	u32 mask;
+
+	mask = GENMASK(tmdev->num_sensors - 1, 0);
+	mask <<= TSENS_SENSOR0_SHIFT;
+	mask |= TSENS_EN;
+
+	regmap_read(tmdev->map, TSENS_CNTL_ADDR, &reg_cntl);
+	reg_cntl &= ~mask;
+	if (tmdev->num_sensors > 1)
+		reg_cntl &= ~TSENS_8960_SLP_CLK_ENA;
+	else
+		reg_cntl &= ~TSENS_8660_SLP_CLK_ENA;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+}
+
+static void tsens_hw_init(struct tsens_device *tmdev)
+{
+	u32 reg_cntl, reg_thr;
+
+	reg_cntl = TSENS_SW_RST;
+	regmap_update_bits(tmdev->map, TSENS_CNTL_ADDR, TSENS_SW_RST, reg_cntl);
+
+	if (tmdev->num_sensors > 1) {
+		reg_cntl |= TSENS_8960_SLP_CLK_ENA | TSENS_8960_MEASURE_PERIOD;
+		reg_cntl &= ~TSENS_SW_RST;
+		regmap_update_bits(tmdev->map, TSENS_8960_CONFIG_ADDR,
+				   TSENS_8960_CONFIG_MASK, TSENS_8960_CONFIG);
+	} else {
+		reg_cntl |= TSENS_8660_SLP_CLK_ENA | TSENS_8660_MEASURE_PERIOD;
+		reg_cntl &= ~TSENS_8660_CONFIG_MASK;
+		reg_cntl |= TSENS_8660_CONFIG << TSENS_8660_CONFIG_SHIFT;
+	}
+
+	reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << TSENS_SENSOR0_SHIFT;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+
+	regmap_field_update_bits(tmdev->status_field,
+			TSENS_LOWER_STATUS_CLR | TSENS_UPPER_STATUS_CLR |
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK,
+			TSENS_LOWER_STATUS_CLR | TSENS_UPPER_STATUS_CLR |
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK);
+
+	reg_cntl |= TSENS_EN;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+
+	reg_thr = (TSENS_LOWER_LIMIT_TH << TSENS_THRESHOLD_LOWER_LIMIT_SHIFT) |
+		(TSENS_UPPER_LIMIT_TH << TSENS_THRESHOLD_UPPER_LIMIT_SHIFT) |
+		(TSENS_MIN_LIMIT_TH << TSENS_THRESHOLD_MIN_LIMIT_SHIFT) |
+		(TSENS_MAX_LIMIT_TH << TSENS_THRESHOLD_MAX_LIMIT_SHIFT);
+	regmap_write(tmdev->map, TSENS_THRESHOLD_ADDR, reg_thr);
+}
+
+static int
+tsens_calib_sensors(struct tsens_device *tmdev)
+{
+	int i;
+	u8 *byte_data;
+
+	u32 num_read = tmdev->num_sensors;
+	struct tsens_sensor *s = tmdev->sensor;
+
+	byte_data = devm_qfprom_get_data_byname(tmdev->dev, "calib", &num_read);
+
+	if (IS_ERR(byte_data) || !byte_data[0])
+		byte_data = devm_qfprom_get_data_byname(tmdev->dev,
+			"backup_calib", &num_read);
+
+	if (IS_ERR(byte_data) || !byte_data[0]
+		|| num_read != tmdev->num_sensors)

drivers/thermal/qcom-tsens.c line 333

Quoted 10 lines
drivers/thermal/qcom-tsens.c new file +10 -0
+		return -EINVAL;
+
+	for (i = 0; i < num_read; i++, s++)
+		s->offset = TSENS_CAL_MDEGC - s->slope * byte_data[i];
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops tsens_thermal_of_ops = {
+	.get_temp = tsens_tz_get_temp,

Thermal governors expect trip temperatures be returned from the TZ driver.
Consider implementing the other ops.

See thermal IPA governor from Javi Merino.

Quoted 172 lines
drivers/thermal/qcom-tsens.c new file +165 -0
+};
+
+static int tsens_register(struct tsens_device *tmdev, int i)
+{
+	u32 addr = TSENS_S0_STATUS_ADDR;
+	struct tsens_sensor *s = &tmdev->sensor[i];
+
+	/*
+	* The status registers for each sensor are discontiguous
+	* because some SoCs have 5 sensors while others have more
+	* but the control registers stay in the same place, i.e.
+	* directly after the first 5 status registers.
+	*/
+	if (i >= 5)
+		addr += TSENS_SENSORABOVEFIVE_OFFSET;
+
+	addr += i * 4;
+
+	s->mode = THERMAL_DEVICE_ENABLED;
+	s->sensor_num = i;
+	s->status = addr;
+	s->tmdev = tmdev;
+	s->tz_dev = thermal_zone_of_sensor_register(tmdev->dev, i, s,
+						&tsens_thermal_of_ops);
+
+	if (IS_ERR(s->tz_dev))
+		return -ENODEV;
+
+	return 0;
+}
+
+static int tsens_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int ret, i, num;
+	struct tsens_sensor *s;
+	struct tsens_device *tmdev;
+	struct regmap *map;
+	struct reg_field *field;
+	static struct reg_field status_0 = {
+		.reg = TSENS_8064_STATUS_CNTL,
+		.lsb = 0,
+		.msb = 3,
+	};
+	static struct reg_field status_8 = {
+		.reg = TSENS_CNTL_ADDR,
+		.lsb = 8,
+		.msb = 11,
+	};
+
+	num = of_property_count_u32_elems(np, "qcom,tsens-slopes");
+	if (num <= 0) {
+		dev_err(&pdev->dev, "invalid tsens slopes\n");
+		return -EINVAL;
+	}
+
+	tmdev = devm_kzalloc(&pdev->dev, sizeof(*tmdev) +
+			     num * sizeof(struct tsens_sensor), GFP_KERNEL);
+	if (tmdev == NULL)
+		return -ENOMEM;
+
+	tmdev->dev = &pdev->dev;
+	tmdev->num_sensors = num;
+
+	for (i = 0, s = tmdev->sensor; i < num; i++, s++)
+		of_property_read_u32_index(np, "qcom,tsens-slopes", i,
+					   &s->slope);
+
+	ret = tsens_calib_sensors(tmdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "tsense calibration failed\n");
+		return ret;
+	}
+
+	tmdev->map = map = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!map)
+		return -ENODEV;
+
+	/* Status bits move when the sensor bits next to them overlap */
+	if (num > 5)
+		field = &status_0;
+	else
+		field = &status_8;
+
+	tmdev->status_field = devm_regmap_field_alloc(&pdev->dev, map, *field);
+	if (IS_ERR(tmdev->status_field)) {
+		dev_err(&pdev->dev, "regmap alloc failed\n");
+		return PTR_ERR(tmdev->status_field);
+	}
+
+	tsens_hw_init(tmdev);
+
+	/*
+	* Register sensor 0 separately. This sensor is always
+	* expected to be present and if this fails, thermal
+	* sensor probe would fail.
+	* Other sensors are optional and if registration fails
+	* disable the sensor and continue
+	*/
+	ret = tsens_register(tmdev, 0);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Registering failed for primary sensor");
+		ret = -ENODEV;
+		goto fail;
+	} else {
+		tsens_tz_set_mode(&tmdev->sensor[0], THERMAL_DEVICE_ENABLED);
+	}
+
+	for (i = 1;  i < tmdev->num_sensors; i++) {
+		ret = tsens_register(tmdev, i);
+
+		if (ret < 0) {
+			dev_err(&pdev->dev,
+				"Registering sensor(%i) failed - disabled", i);
+			tsens_tz_set_mode(&tmdev->sensor[i],
+				THERMAL_DEVICE_DISABLED);
+		} else {
+			tsens_tz_set_mode(&tmdev->sensor[i],
+				THERMAL_DEVICE_ENABLED);
+		}
+	}
+
+	platform_set_drvdata(pdev, tmdev);
+
+	return 0;
+fail:
+	dev_err(&pdev->dev, "Tsens driver init failed\n");
+	tsens_disable_mode(tmdev);
+	return ret;
+}
+
+static int tsens_remove(struct platform_device *pdev)
+{
+	int i;
+	struct tsens_sensor *s;
+	struct tsens_device *tmdev = platform_get_drvdata(pdev);
+
+	tsens_disable_mode(tmdev);
+	for (i = 0, s = tmdev->sensor; i < tmdev->num_sensors; i++, s++)
+		thermal_zone_device_unregister(s->tz_dev);
+
+	return 0;
+}
+
+static struct of_device_id tsens_match_table[] = {
+	{.compatible = "qcom,qcom-tsens"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsens_match_table);
+
+static struct platform_driver tsens_driver = {
+	.probe = tsens_probe,
+	.remove = tsens_remove,
+	.driver = {
+		.of_match_table = tsens_match_table,
+		.name = "qcom-tsens",
+		.pm	= TSENS_PM_OPS,
+	},
+};
+module_platform_driver(tsens_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("QCOM Temperature Sensor driver");
+MODULE_ALIAS("platform:qcom-tsens");
Signature · 6 lines
Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#3 lore raw
Quoted 24 lines · Lina Iyer
Quoted 14 lines · Narendran Rajan

TSENS supports reading temperature from multiple thermal sensors present in QCOM SOCs.
TSENS HW is enabled only when the main sensor is requested. TSENS block is disabled if the main senors is disabled irrespective of any other sensors that are being enabled

The driver needs calibration data which is read from qfprom. Calibration data location is configured through dt files.

Based on code by Siddartha Mohanadoss and Stephen Boyd.

Cc Siddartha Mohanadoss <[email protected]>
Cc Stephen Boyd <[email protected]>
Quoted 8 lines

---

.../devicetree/bindings/thermal/qcom-thermal.txt   |  59 +++
drivers/thermal/Kconfig                            |  14 +
drivers/thermal/Makefile                           |   1 +
drivers/thermal/qcom-tsens.c                       | 498 +++++++++++++++++++++
4 files changed, 572 insertions(+)

create mode 100644 Documentation/devicetree/bindings/thermal/qcom-thermal.txt create mode 100644 drivers/thermal/qcom-tsens.c

Quoted 2 lines

Why is the devicetree nodes not part of the series. Without the devicetree this driver does not provide any functionality on the SoC.

and also makes reviewing the driver easier. Besides, one can test your full driver, if you provice your dts in your series.

Quoted 463 lines

Consider supporting 8084,8074,8064, 8016 as part of this series.

Quoted 7 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +0 -0
new file mode 100644
index 0000000..c8ab66b

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 7

Quoted 7 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +7 -0
@@ -0,0 +1,59 @@
+* QCOM SoC Temperature Sensor (TSENS)
+
+Required properties:
+- compatible : "qcom,qcom-tsens"
+- qcom,tsens-slopes : Must contain slope value for each of the sensors controlled
+			by this device
+- qcom,qfprom : An arry of triplets containing tsens calibration data.

/s/arry/array

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 9

Quoted 2 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +2 -0
+		The first element in the triplet is a phandle
+                to qfprom compatible node, second element is a offset to calibration

s/a offset/an offset

Documentation/devicetree/bindings/thermal/qcom-thermal.txt line 18

Quoted 9 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +9 -0
+                data within this node, third element indicates size of calibration
+                data.
+                In general, there would be two elements in this array
+                - first containing information on primary calibration data
+                - second containing information on backup calibration data
+- qcom,qfprom-names : Names for each calibration data
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+
+Exiample:

Example

Quoted 46 lines
Documentation/devicetree/bindings/thermal/qcom-thermal.txt new file +41 -0
+tsens: tsens-qcom {
+		compatible = "qcom,qcom-tsens";
+		qcom,tsens-slopes = <1176 1176 1154 1176 1111
+				1132 1132 1199 1132 1199
+				1132>;
+		qcom,qfprom = <&imem 0x400 11>, <&imem 0x410 11>;
+		qcom,qfprom-names = "calib", "backup_calib";
+		#thermal-sensor-cells = <1>;
+	};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsens	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <80000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <120000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+					<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
drivers/thermal/Kconfig +0 -0
index 20915ca..c085405 100644

drivers/thermal/Kconfig config INTEL_SOC_DTS_THERMAL · line 264

Quoted 4 lines
drivers/thermal/Kconfig +1 -0
@@ -261,6 +261,20 @@ config INTEL_SOC_DTS_THERMAL
 	  notification methods.The other trip is a critical trip point, which
 	  was set by the driver based on the TJ MAX temperature.
 
+config THERMAL_QCOMTSENS

THERMAL_QCOM_TSENS

Quoted 93 lines
drivers/thermal/Kconfig +13 -0
+	tristate "Qualcomm Tsens Temperature driver"
+	depends on THERMAL
+	depends on ARCH_QCOM
+	help
+	  QCOM tsens thermal driver provides support for Temperature sensor
+	  (TSENS) found on QCOM SoCs. It supports four configurable trip points
+	  and controls multiple sensors on the SOC. The four trip points are
+	  common across all sensors present in the SoC. The number of sensors
+	  present vary from chip to chip and are set through device tree entry.
+	  The driver presents as a standard thermal zone device with configurable
+	  trip points and cooling device mapping through standard thermal zone
+	  device tree
+

menu "ACPI INT340X thermal drivers"
source drivers/thermal/int340x_thermal/Kconfig
endmenu

drivers/thermal/Makefile +0 -0
index fa0dc48..3fdf6b9 100644
@@ -39,3 +39,4 @@ obj-$(CONFIG_TI_SOC_THERMAL)	+= ti-soc-thermal/

obj-$(CONFIG_INT340X_THERMAL) += int340x_thermal/
obj-$(CONFIG_ST_THERMAL) += st/
obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o

drivers/thermal/Makefile +1 -0
+obj-$(CONFIG_THERMAL_QCOMTSENS)	+= qcom-tsens.o
drivers/thermal/qcom-tsens.c new file +62 -0
new file mode 100644
index 0000000..a794961
@@ -0,0 +1,498 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/pm.h>
+#include <linux/bitops.h>
+#include <linux/regmap.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <soc/qcom/qfprom.h>
+
+#define TSENS_CAL_MDEGC				30000
+
+#define TSENS_8960_CONFIG_ADDR			0x3640
+#define TSENS_8960_CONFIG			0x9b
+#define TSENS_8960_CONFIG_MASK			0xf
+
+#define TSENS_CNTL_ADDR				0x3620
+#define TSENS_EN				BIT(0)
+#define TSENS_SW_RST				BIT(1)
+#define SENSOR0_EN				BIT(3)
+#define TSENS_MIN_STATUS_MASK			BIT(0)
+#define TSENS_LOWER_STATUS_CLR			BIT(1)
+#define TSENS_UPPER_STATUS_CLR			BIT(2)
+#define TSENS_MAX_STATUS_MASK			BIT(3)
+#define TSENS_8960_MEASURE_PERIOD		BIT(18)
+#define TSENS_8660_MEASURE_PERIOD		BIT(16)
+#define TSENS_8960_SLP_CLK_ENA			BIT(26)
+#define TSENS_8660_SLP_CLK_ENA			BIT(24)
+#define TSENS_8064_STATUS_CNTL			0x3660
+
+#define TSENS_THRESHOLD_ADDR			0x3624
+#define TSENS_THRESHOLD_MAX_CODE		0xff
+#define TSENS_THRESHOLD_MIN_CODE		0
+#define TSENS_THRESHOLD_MAX_LIMIT_SHIFT		24
+#define TSENS_THRESHOLD_MIN_LIMIT_SHIFT		16
+#define TSENS_THRESHOLD_UPPER_LIMIT_SHIFT	8
+#define TSENS_THRESHOLD_LOWER_LIMIT_SHIFT	0
+
+/* Initial temperature threshold values */
+#define TSENS_LOWER_LIMIT_TH			0x50
+#define TSENS_UPPER_LIMIT_TH			0xdf
+#define TSENS_MIN_LIMIT_TH			0x0
+#define TSENS_MAX_LIMIT_TH			0xff
+
+#define TSENS_S0_STATUS_ADDR			0x3628

drivers/thermal/qcom-tsens.c line 72

Quoted 10 lines
drivers/thermal/qcom-tsens.c new file +10 -0
+
+#define TSENS_INT_STATUS_ADDR			0x363c
+#define TSENS_TRDY_MASK				BIT(7)
+
+#define TSENS_SENSOR0_SHIFT			3
+
+#define TSENS_8660_CONFIG			1
+#define TSENS_8660_CONFIG_SHIFT			28
+#define TSENS_8660_CONFIG_MASK			(3 << TSENS_8660_CONFIG_SHIFT)
+#define TSENS_SENSORABOVEFIVE_OFFSET		40

Needs alignment.

Quoted 251 lines
drivers/thermal/qcom-tsens.c new file +251 -0
+
+struct tsens_device;
+
+struct tsens_sensor {
+	struct thermal_zone_device	*tz_dev;
+	enum thermal_device_mode	mode;
+	unsigned int			sensor_num;
+	int				offset;
+	int				slope;
+	struct tsens_device		*tmdev;
+	u32                             status;
+};
+
+struct tsens_device {
+	struct device		*dev;
+	bool			prev_reading_avail;
+	unsigned int		num_sensors;
+	int			pm_tsens_thr_data;
+	int			pm_tsens_cntl;
+	struct regmap		*map;
+	struct regmap_field	*status_field;
+	struct tsens_sensor	sensor[0];
+};
+
+/* Temperature on y axis and ADC-code on x-axis */
+static int
+tsens_tz_code_to_mdegC(u32 adc_code, const struct tsens_sensor *s)
+{
+	return adc_code * s->slope + s->offset;
+}
+
+static int tsens_tz_get_temp(void *_sensor,
+			     long *temp)
+{
+	const struct tsens_sensor *tm_sensor = _sensor;
+	struct tsens_device *tmdev = tm_sensor->tmdev;
+	u32 code, trdy;
+
+	if (tm_sensor->mode != THERMAL_DEVICE_ENABLED)
+		return -EINVAL;
+
+	if (!tmdev->prev_reading_avail) {
+		while (!regmap_read(tmdev->map, TSENS_INT_STATUS_ADDR, &trdy) &&
+		       !(trdy & TSENS_TRDY_MASK))
+			usleep_range(1000, 1100);
+		tmdev->prev_reading_avail = true;
+	}
+
+	regmap_read(tmdev->map, tm_sensor->status, &code);
+	*temp = tsens_tz_code_to_mdegC(code, tm_sensor);
+
+	dev_dbg(tmdev->dev, "Sensor %d temp is: %ld",
+		tm_sensor->sensor_num, *temp);
+	return 0;
+}
+
+/*
+ * If the main sensor is disabled all the sensors are disable and
+ * the clock is disabled.
+ * If the main sensor is disabled and a sub-sensor is enabled
+ * return with an error.
+ */
+static int tsens_tz_set_mode(struct tsens_sensor *tm_sensor,
+			      enum thermal_device_mode mode)
+{
+	struct tsens_device *tmdev = tm_sensor->tmdev;
+	unsigned int i, n = tmdev->num_sensors;
+	u32 reg, mask;
+
+	if (mode == tm_sensor->mode)
+		return 0;
+
+	regmap_read(tmdev->map, TSENS_CNTL_ADDR, &reg);
+
+	mask = BIT(tm_sensor->sensor_num + TSENS_SENSOR0_SHIFT);
+	if (mode == THERMAL_DEVICE_ENABLED) {
+		if (!(reg & SENSOR0_EN) && mask != SENSOR0_EN) {
+			dev_warn(tmdev->dev, "Main sensor not enabled\n");
+			return -EINVAL;
+		}
+
+		regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg | TSENS_SW_RST);
+		if (tmdev->num_sensors > 1)
+			reg |= mask | TSENS_8960_SLP_CLK_ENA | TSENS_EN;
+		else
+			reg |= mask | TSENS_8660_SLP_CLK_ENA | TSENS_EN;
+		tmdev->prev_reading_avail = false;
+	} else {
+		reg &= ~mask;
+		if (!(reg & SENSOR0_EN)) {
+			dev_warn(tmdev->dev, "Main sensor not enabled. Disabling subsensors\n");
+
+			reg &= ~GENMASK(n + TSENS_SENSOR0_SHIFT - 1,
+					TSENS_SENSOR0_SHIFT);
+			reg &= ~TSENS_EN;
+
+			if (tmdev->num_sensors > 1)
+				reg &= ~TSENS_8960_SLP_CLK_ENA;
+			else
+				reg &= ~TSENS_8660_SLP_CLK_ENA;
+
+			/* Disable all sub-sensors */
+			for (i = 1; i < n; i++)
+				tmdev->sensor[i].mode = mode;
+		}
+	}
+
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg);
+	tm_sensor->mode = mode;
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int tsens_suspend(struct device *dev)
+{
+	int i;
+	unsigned int mask;
+	struct tsens_device *tmdev = dev_get_drvdata(dev);
+	struct regmap *map = tmdev->map;
+
+	regmap_read(map, TSENS_THRESHOLD_ADDR, &tmdev->pm_tsens_thr_data);
+	regmap_read(map, TSENS_CNTL_ADDR, &tmdev->pm_tsens_cntl);
+
+	if (tmdev->num_sensors > 1)
+		mask = TSENS_8960_SLP_CLK_ENA | TSENS_EN;
+	else
+		mask = TSENS_8660_SLP_CLK_ENA | TSENS_EN;
+
+	regmap_update_bits(map, TSENS_CNTL_ADDR, mask, 0);
+
+	tmdev->prev_reading_avail = 0;
+	for (i = 0; i < tmdev->num_sensors; i++)
+		tmdev->sensor[i].mode = THERMAL_DEVICE_DISABLED;
+
+	return 0;
+}
+
+static int tsens_resume(struct device *dev)
+{
+	int i;
+	unsigned long reg_cntl;
+	struct tsens_device *tmdev = dev_get_drvdata(dev);
+	struct regmap *map = tmdev->map;
+
+	regmap_update_bits(map, TSENS_CNTL_ADDR, TSENS_SW_RST, TSENS_SW_RST);
+	regmap_field_update_bits(tmdev->status_field,
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK,
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK);
+
+	/*
+	* Separate CONFIG restore is needed only for 8960. For 8660
+	* config is part of CTRL Addr and its restored as such
+	*/
+	if (tmdev->num_sensors > 1)
+		regmap_update_bits(map, TSENS_8960_CONFIG_ADDR,
+				TSENS_8960_CONFIG_MASK,
+				TSENS_8960_CONFIG);
+
+	regmap_write(map, TSENS_THRESHOLD_ADDR, tmdev->pm_tsens_thr_data);
+	regmap_write(map, TSENS_CNTL_ADDR, tmdev->pm_tsens_cntl);
+
+	reg_cntl = tmdev->pm_tsens_cntl;
+	reg_cntl >>= TSENS_SENSOR0_SHIFT;
+	for_each_set_bit(i, &reg_cntl, tmdev->num_sensors)
+		tmdev->sensor[i].mode = THERMAL_DEVICE_ENABLED;
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(tsens_pm_ops, tsens_suspend, tsens_resume);
+#define TSENS_PM_OPS	(&tsens_pm_ops)
+
+#else /* CONFIG_PM_SLEEP */
+
+#define TSENS_PM_OPS	NULL
+
+#endif /* CONFIG_PM_SLEEP */
+
+static void tsens_disable_mode(const struct tsens_device *tmdev)
+{
+	u32 reg_cntl;
+	u32 mask;
+
+	mask = GENMASK(tmdev->num_sensors - 1, 0);
+	mask <<= TSENS_SENSOR0_SHIFT;
+	mask |= TSENS_EN;
+
+	regmap_read(tmdev->map, TSENS_CNTL_ADDR, &reg_cntl);
+	reg_cntl &= ~mask;
+	if (tmdev->num_sensors > 1)
+		reg_cntl &= ~TSENS_8960_SLP_CLK_ENA;
+	else
+		reg_cntl &= ~TSENS_8660_SLP_CLK_ENA;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+}
+
+static void tsens_hw_init(struct tsens_device *tmdev)
+{
+	u32 reg_cntl, reg_thr;
+
+	reg_cntl = TSENS_SW_RST;
+	regmap_update_bits(tmdev->map, TSENS_CNTL_ADDR, TSENS_SW_RST, reg_cntl);
+
+	if (tmdev->num_sensors > 1) {
+		reg_cntl |= TSENS_8960_SLP_CLK_ENA | TSENS_8960_MEASURE_PERIOD;
+		reg_cntl &= ~TSENS_SW_RST;
+		regmap_update_bits(tmdev->map, TSENS_8960_CONFIG_ADDR,
+				   TSENS_8960_CONFIG_MASK, TSENS_8960_CONFIG);
+	} else {
+		reg_cntl |= TSENS_8660_SLP_CLK_ENA | TSENS_8660_MEASURE_PERIOD;
+		reg_cntl &= ~TSENS_8660_CONFIG_MASK;
+		reg_cntl |= TSENS_8660_CONFIG << TSENS_8660_CONFIG_SHIFT;
+	}
+
+	reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << TSENS_SENSOR0_SHIFT;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+
+	regmap_field_update_bits(tmdev->status_field,
+			TSENS_LOWER_STATUS_CLR | TSENS_UPPER_STATUS_CLR |
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK,
+			TSENS_LOWER_STATUS_CLR | TSENS_UPPER_STATUS_CLR |
+			TSENS_MIN_STATUS_MASK | TSENS_MAX_STATUS_MASK);
+
+	reg_cntl |= TSENS_EN;
+	regmap_write(tmdev->map, TSENS_CNTL_ADDR, reg_cntl);
+
+	reg_thr = (TSENS_LOWER_LIMIT_TH << TSENS_THRESHOLD_LOWER_LIMIT_SHIFT) |
+		(TSENS_UPPER_LIMIT_TH << TSENS_THRESHOLD_UPPER_LIMIT_SHIFT) |
+		(TSENS_MIN_LIMIT_TH << TSENS_THRESHOLD_MIN_LIMIT_SHIFT) |
+		(TSENS_MAX_LIMIT_TH << TSENS_THRESHOLD_MAX_LIMIT_SHIFT);
+	regmap_write(tmdev->map, TSENS_THRESHOLD_ADDR, reg_thr);
+}
+
+static int
+tsens_calib_sensors(struct tsens_device *tmdev)
+{
+	int i;
+	u8 *byte_data;
+
+	u32 num_read = tmdev->num_sensors;
+	struct tsens_sensor *s = tmdev->sensor;
+
+	byte_data = devm_qfprom_get_data_byname(tmdev->dev, "calib", &num_read);
+
+	if (IS_ERR(byte_data) || !byte_data[0])
+		byte_data = devm_qfprom_get_data_byname(tmdev->dev,
+			"backup_calib", &num_read);
+
+	if (IS_ERR(byte_data) || !byte_data[0]
+		|| num_read != tmdev->num_sensors)

drivers/thermal/qcom-tsens.c line 333

Quoted 10 lines
drivers/thermal/qcom-tsens.c new file +10 -0
+		return -EINVAL;
+
+	for (i = 0; i < num_read; i++, s++)
+		s->offset = TSENS_CAL_MDEGC - s->slope * byte_data[i];
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops tsens_thermal_of_ops = {
+	.get_temp = tsens_tz_get_temp,

Thermal governors expect trip temperatures be returned from the TZ driver.
Consider implementing the other ops.

Quoted 1 line

See thermal IPA governor from Javi Merino.

The implementation about is correct. The required trip point data will be provided by the of-thermal wrappers.

However, there are other ops that may help your driver, like providing trend and debug options.

BR,

Eduardo Valentin

Quoted 173 lines
Quoted 173 lines
drivers/thermal/qcom-tsens.c new file +165 -0
+};
+
+static int tsens_register(struct tsens_device *tmdev, int i)
+{
+	u32 addr = TSENS_S0_STATUS_ADDR;
+	struct tsens_sensor *s = &tmdev->sensor[i];
+
+	/*
+	* The status registers for each sensor are discontiguous
+	* because some SoCs have 5 sensors while others have more
+	* but the control registers stay in the same place, i.e.
+	* directly after the first 5 status registers.
+	*/
+	if (i >= 5)
+		addr += TSENS_SENSORABOVEFIVE_OFFSET;
+
+	addr += i * 4;
+
+	s->mode = THERMAL_DEVICE_ENABLED;
+	s->sensor_num = i;
+	s->status = addr;
+	s->tmdev = tmdev;
+	s->tz_dev = thermal_zone_of_sensor_register(tmdev->dev, i, s,
+						&tsens_thermal_of_ops);
+
+	if (IS_ERR(s->tz_dev))
+		return -ENODEV;
+
+	return 0;
+}
+
+static int tsens_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int ret, i, num;
+	struct tsens_sensor *s;
+	struct tsens_device *tmdev;
+	struct regmap *map;
+	struct reg_field *field;
+	static struct reg_field status_0 = {
+		.reg = TSENS_8064_STATUS_CNTL,
+		.lsb = 0,
+		.msb = 3,
+	};
+	static struct reg_field status_8 = {
+		.reg = TSENS_CNTL_ADDR,
+		.lsb = 8,
+		.msb = 11,
+	};
+
+	num = of_property_count_u32_elems(np, "qcom,tsens-slopes");
+	if (num <= 0) {
+		dev_err(&pdev->dev, "invalid tsens slopes\n");
+		return -EINVAL;
+	}
+
+	tmdev = devm_kzalloc(&pdev->dev, sizeof(*tmdev) +
+			     num * sizeof(struct tsens_sensor), GFP_KERNEL);
+	if (tmdev == NULL)
+		return -ENOMEM;
+
+	tmdev->dev = &pdev->dev;
+	tmdev->num_sensors = num;
+
+	for (i = 0, s = tmdev->sensor; i < num; i++, s++)
+		of_property_read_u32_index(np, "qcom,tsens-slopes", i,
+					   &s->slope);
+
+	ret = tsens_calib_sensors(tmdev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "tsense calibration failed\n");
+		return ret;
+	}
+
+	tmdev->map = map = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!map)
+		return -ENODEV;
+
+	/* Status bits move when the sensor bits next to them overlap */
+	if (num > 5)
+		field = &status_0;
+	else
+		field = &status_8;
+
+	tmdev->status_field = devm_regmap_field_alloc(&pdev->dev, map, *field);
+	if (IS_ERR(tmdev->status_field)) {
+		dev_err(&pdev->dev, "regmap alloc failed\n");
+		return PTR_ERR(tmdev->status_field);
+	}
+
+	tsens_hw_init(tmdev);
+
+	/*
+	* Register sensor 0 separately. This sensor is always
+	* expected to be present and if this fails, thermal
+	* sensor probe would fail.
+	* Other sensors are optional and if registration fails
+	* disable the sensor and continue
+	*/
+	ret = tsens_register(tmdev, 0);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Registering failed for primary sensor");
+		ret = -ENODEV;
+		goto fail;
+	} else {
+		tsens_tz_set_mode(&tmdev->sensor[0], THERMAL_DEVICE_ENABLED);
+	}
+
+	for (i = 1;  i < tmdev->num_sensors; i++) {
+		ret = tsens_register(tmdev, i);
+
+		if (ret < 0) {
+			dev_err(&pdev->dev,
+				"Registering sensor(%i) failed - disabled", i);
+			tsens_tz_set_mode(&tmdev->sensor[i],
+				THERMAL_DEVICE_DISABLED);
+		} else {
+			tsens_tz_set_mode(&tmdev->sensor[i],
+				THERMAL_DEVICE_ENABLED);
+		}
+	}
+
+	platform_set_drvdata(pdev, tmdev);
+
+	return 0;
+fail:
+	dev_err(&pdev->dev, "Tsens driver init failed\n");
+	tsens_disable_mode(tmdev);
+	return ret;
+}
+
+static int tsens_remove(struct platform_device *pdev)
+{
+	int i;
+	struct tsens_sensor *s;
+	struct tsens_device *tmdev = platform_get_drvdata(pdev);
+
+	tsens_disable_mode(tmdev);
+	for (i = 0, s = tmdev->sensor; i < tmdev->num_sensors; i++, s++)
+		thermal_zone_device_unregister(s->tz_dev);
+
+	return 0;
+}
+
+static struct of_device_id tsens_match_table[] = {
+	{.compatible = "qcom,qcom-tsens"},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, tsens_match_table);
+
+static struct platform_driver tsens_driver = {
+	.probe = tsens_probe,
+	.remove = tsens_remove,
+	.driver = {
+		.of_match_table = tsens_match_table,
+		.name = "qcom-tsens",
+		.pm	= TSENS_PM_OPS,
+	},
+};
+module_platform_driver(tsens_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("QCOM Temperature Sensor driver");
+MODULE_ALIAS("platform:qcom-tsens");
Signature · 6 lines
Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html