Skip to contentSkip to conversation

Bluetooth: Add device shutdown routine for Intel Bluetooth device

PATCH In review Tedd Ho-Jeong An 2 participants 2 messages Feb 13, 2015 – Feb 14, 2015 Bluetooth drivers

lore
Share & tools
lore

Tedd Ho-Jeong An

author
#0 lore raw

PATCH v2 2/2 Bluetooth: Add device shutdown routine for Intel Bluetooth device

From: Tedd Ho-Jeong An <[email protected]>

This patch adds the device shutdown routine for Intel Bluetooth device.

Some platforms have BT LED issue with Intel Bluetooth device that BT LED goes off 5 seconds after BT is turned off

For Intel Bluetooth device, the BT LED is turned off when:
- there is no active connection or radio activity
- USB is suspend

So, when the BT is turned off, it takes 5 seconds because USB suspend timeone is 5 seconds by default. And if the USB suspend is not enabled, BT LED won't be turned off.

To fix this issue, recently Intel Bluetooth firmware patch had been submitted to turn off the BT LED immediately by the vendor specific command(0xFC3F). And this patch sends this command to the device before closing the device.

For backward compatibility of this command with old firmware, this command was supported before, but it behaves same as HCI_RESET internally. So, it won't be the problem even if the system doesn't have the latest firmware patch.

Signed-off-by Tedd Ho-Jeong An <[email protected]>
---
 drivers/bluetooth/btusb.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
drivers/bluetooth/btusb.c +22 -0
index b876888..b2c099a 100644
@@ -2331,6 +2331,27 @@ static int btusb_set_bdaddr_intel(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 	return 0;
 }
 
+static int btusb_shutdown_intel(struct hci_dev *hdev)
+{
+	struct sk_buff *skb;
+	long ret;
+
+	/* Some platforms have an issue with BT LED when hci interface is down or
+	 * BT radio is turned off, which takes 5 seconds to BT LED goes off.
+	 * This command turns off the BT LED immediately.
+	 */
+	skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		ret = PTR_ERR(skb);
+		BT_ERR("%s: turning off Intel device LED failed (%ld)",
+		       hdev->name, ret);
+		return ret;
+	}
+	kfree_skb(skb);
+
+	return 0;
+}
+
 static int btusb_set_bdaddr_marvell(struct hci_dev *hdev,
 				    const bdaddr_t *bdaddr)
 {

@@ -2708,6 +2729,7 @@ static int btusb_probe(struct usb_interface *intf,
 
 	if (id->driver_info & BTUSB_INTEL) {
 		hdev->setup = btusb_setup_intel;
+		hdev->shutdown = btusb_shutdown_intel;
 		hdev->set_bdaddr = btusb_set_bdaddr_intel;
 		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
 	}
Signature · 1 line
1.9.1
maintainer
#1 lore raw

Hi Tedd,

Quoted 33 lines

This patch adds the device shutdown routine for Intel Bluetooth device.

Some platforms have BT LED issue with Intel Bluetooth device that BT LED goes off 5 seconds after BT is turned off

For Intel Bluetooth device, the BT LED is turned off when:
- there is no active connection or radio activity
- USB is suspend

So, when the BT is turned off, it takes 5 seconds because USB suspend timeone is 5 seconds by default. And if the USB suspend is not enabled, BT LED won't be turned off.

To fix this issue, recently Intel Bluetooth firmware patch had been submitted to turn off the BT LED immediately by the vendor specific command(0xFC3F). And this patch sends this command to the device before closing the device.

For backward compatibility of this command with old firmware, this command was supported before, but it behaves same as HCI_RESET internally. So, it won't be the problem even if the system doesn't have the latest firmware patch.

Signed-off-by Tedd Ho-Jeong An <[email protected]>

---
drivers/bluetooth/btusb.c | 22 ++++++++++++++++++++++

1 file changed, 22 insertions(+)
drivers/bluetooth/btusb.c +0 -0
index b876888..b2c099a 100644
@@ -2331,6 +2331,27 @@ static int btusb_set_bdaddr_intel(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 	return 0;
 }

drivers/bluetooth/btusb.c static int btusb_set_bdaddr_intel(struct hci_dev *hdev, const bdaddr_t *bdaddr) · line 2342

Quoted 10 lines
drivers/bluetooth/btusb.c +9 -0
 
+static int btusb_shutdown_intel(struct hci_dev *hdev)
+{
+	struct sk_buff *skb;
+	long ret;
+
+	/* Some platforms have an issue with BT LED when hci interface is down or
+	 * BT radio is turned off, which takes 5 seconds to BT LED goes off.
+	 * This command turns off the BT LED immediately.
+	 */

you need to make sure that you are not exceeding the 78 chars limit with your comment. I fixed that up before applying the patch.

drivers/bluetooth/btusb.c static int btusb_set_bdaddr_intel(struct hci_dev *hdev, const bdaddr_t *bdaddr) · line 2354

Quoted 12 lines
drivers/bluetooth/btusb.c +12 -0
+	skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		ret = PTR_ERR(skb);
+		BT_ERR("%s: turning off Intel device LED failed (%ld)",
+		       hdev->name, ret);
+		return ret;
+	}
+	kfree_skb(skb);
+
+	return 0;
+}
+

Patch has been applied to bluetooth-next tree.

Regards

Marcel