Skip to contentSkip to conversation

keystone2: ddr3: eliminate using global ddr3_size variable

PATCH In review Vitaly Andrianov 3 participants 3 messages Feb 11, 2015 – Feb 17, 2015 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 keystone2: ddr3: eliminate using global ddr3_size variable

KS2 ddr3 initialization uses ddr3_size global variable before u-boot relocation. Even if the variable is not being used after relocation, writing to it corrupts relocation table.

This patch removes the global ddr3_size variable and uses local one instead.

---
 arch/arm/cpu/armv7/keystone/ddr3.c        |  5 +----
 arch/arm/include/asm/arch-keystone/ddr3.h |  5 ++---
 board/ti/ks2_evm/board.c                  |  6 ++++--
 board/ti/ks2_evm/ddr3_k2e.c               | 14 ++++++--------
 board/ti/ks2_evm/ddr3_k2hk.c              | 11 ++---------
 board/ti/ks2_evm/ddr3_k2l.c               | 12 ++----------
 6 files changed, 17 insertions(+), 36 deletions(-)
arch/arm/cpu/armv7/keystone/ddr3.c +1 -4
index 923906a..dfb27b5 100644
@@ -263,17 +263,14 @@ static void ddr3_map_ecc_cic2_irq(u32 base)
 }
 #endif
 
-void ddr3_init_ecc(u32 base)
+void ddr3_init_ecc(u32 base, u32 ddr3_size)
 {
-	u32 ddr3_size;
-
 	if (!ddr3_ecc_support_rmw(base)) {
 		ddr3_disable_ecc(base);
 		return;
 	}
 
 	ddr3_ecc_init_range(base);
-	ddr3_size = ddr3_get_size();
 	ddr3_reset_data(CONFIG_SYS_SDRAM_BASE, ddr3_size);
 
 	/* mapping DDR3 ECC system interrupt from CIC2 to GIC */
arch/arm/include/asm/arch-keystone/ddr3.h +2 -3
index b044d6f..a22c237 100644
@@ -48,10 +48,9 @@ struct ddr3_emif_config {
 	unsigned int sdrfc;
 };
 
-void ddr3_init(void);
-int ddr3_get_size(void);
+u32 ddr3_init(void);
 void ddr3_reset_ddrphy(void);
-void ddr3_init_ecc(u32 base);
+void ddr3_init_ecc(u32 base, u32 ddr3_size);
 void ddr3_disable_ecc(u32 base);
 void ddr3_check_ecc_int(u32 base);
 int ddr3_ecc_support_rmw(u32 base);
board/ti/ks2_evm/board.c +4 -2
index 04ec675..8892a28 100644
@@ -35,12 +35,14 @@ static struct aemif_config aemif_configs[] = {
 
 int dram_init(void)
 {
-	ddr3_init();
+	u32 ddr3_size;
+
+	ddr3_size = ddr3_init();
 
 	gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE,
 				    CONFIG_MAX_RAM_BANK_SIZE);
 	aemif_init(ARRAY_SIZE(aemif_configs), aemif_configs);
-	ddr3_init_ecc(KS2_DDR3A_EMIF_CTRL_BASE);
+	ddr3_init_ecc(KS2_DDR3A_EMIF_CTRL_BASE, ddr3_size);
 	return 0;
 }
 
board/ti/ks2_evm/ddr3_k2e.c +6 -8
index 40fd966..35ffb42 100644
@@ -11,11 +11,11 @@
 #include "ddr3_cfg.h"
 #include <asm/arch/ddr3.h>
 
-static int ddr3_size;
 static struct pll_init_data ddr3_400 = DDR3_PLL_400;
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
+	u32 ddr3_size;
 	char dimm_name[32];
 
 	if (~(readl(KS2_PLL_CNTRL_BASE + KS2_RSTCTRL_RSTYPE) & 0x1))
@@ -43,13 +43,11 @@ void ddr3_init(void)
 		printf("DRAM: 4 GiB\n");
 		ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1600_4g);
 		ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_4g);
+	} else {
+		printf("Unknown SO-DIMM. Cannot configure DDR3\n");
+		while (1)
+			;
 	}
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
 	return ddr3_size;
 }
board/ti/ks2_evm/ddr3_k2hk.c +2 -9
index a1c3d05..b36eb27 100644
@@ -12,14 +12,13 @@
 #include <asm/arch/ddr3.h>
 #include <asm/arch/hardware.h>
 
-static int ddr3_size;
-
 struct pll_init_data ddr3a_333 = DDR3_PLL_333(A);
 struct pll_init_data ddr3a_400 = DDR3_PLL_400(A);
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
 	char dimm_name[32];
+	u32 ddr3_size;
 
 	ddr3_get_dimm_params(dimm_name);
 
@@ -93,12 +92,6 @@ void ddr3_init(void)
 	/* Apply the workaround for PG 1.0 and 1.1 Silicons */
 	if (cpu_revision() <= 1)
 		ddr3_err_reset_workaround();
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
 	return ddr3_size;
 }
board/ti/ks2_evm/ddr3_k2l.c +2 -10
index 15a14f2..00fc194 100644
@@ -11,28 +11,20 @@
 #include "ddr3_cfg.h"
 #include <asm/arch/ddr3.h>
 
-static int ddr3_size;
 static struct pll_init_data ddr3_400 = DDR3_PLL_400;
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
 	init_pll(&ddr3_400);
 
 	/* No SO-DIMM, 2GB discreet DDR */
 	printf("DRAM: 2 GiB\n");
-	ddr3_size = 2;
 
 	/* Reset DDR3 PHY after PLL enabled */
 	ddr3_reset_ddrphy();
 
 	ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1600_2g);
 	ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_2g);
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
-	return ddr3_size;
+	return 2;
 }
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/1 keystone2: ddr3: eliminate using global ddr3_size variable

Quoted 9 lines · Vitaly Andrianov

KS2 ddr3 initialization uses ddr3_size global variable before u-boot relocation. Even if the variable is not being used after relocation, writing to it corrupts relocation table.

This patch removes the global ddr3_size variable and uses local one instead.

---

This patch is necesasry for Keystone2 platforms to boot to u-boot shell.

Tested on v2015.01 tag (which is broke).

Quoted 181 lines
 arch/arm/cpu/armv7/keystone/ddr3.c        |  5 +----
 arch/arm/include/asm/arch-keystone/ddr3.h |  5 ++---
 board/ti/ks2_evm/board.c                  |  6 ++++--
 board/ti/ks2_evm/ddr3_k2e.c               | 14 ++++++--------
 board/ti/ks2_evm/ddr3_k2hk.c              | 11 ++---------
 board/ti/ks2_evm/ddr3_k2l.c               | 12 ++----------
 6 files changed, 17 insertions(+), 36 deletions(-)
arch/arm/cpu/armv7/keystone/ddr3.c +1 -4
index 923906a..dfb27b5 100644
@@ -263,17 +263,14 @@ static void ddr3_map_ecc_cic2_irq(u32 base)
 }
 #endif
 
-void ddr3_init_ecc(u32 base)
+void ddr3_init_ecc(u32 base, u32 ddr3_size)
 {
-	u32 ddr3_size;
-
 	if (!ddr3_ecc_support_rmw(base)) {
 		ddr3_disable_ecc(base);
 		return;
 	}
 
 	ddr3_ecc_init_range(base);
-	ddr3_size = ddr3_get_size();
 	ddr3_reset_data(CONFIG_SYS_SDRAM_BASE, ddr3_size);
 
 	/* mapping DDR3 ECC system interrupt from CIC2 to GIC */
arch/arm/include/asm/arch-keystone/ddr3.h +2 -3
index b044d6f..a22c237 100644
@@ -48,10 +48,9 @@ struct ddr3_emif_config {
 	unsigned int sdrfc;
 };
 
-void ddr3_init(void);
-int ddr3_get_size(void);
+u32 ddr3_init(void);
 void ddr3_reset_ddrphy(void);
-void ddr3_init_ecc(u32 base);
+void ddr3_init_ecc(u32 base, u32 ddr3_size);
 void ddr3_disable_ecc(u32 base);
 void ddr3_check_ecc_int(u32 base);
 int ddr3_ecc_support_rmw(u32 base);
board/ti/ks2_evm/board.c +4 -2
index 04ec675..8892a28 100644
@@ -35,12 +35,14 @@ static struct aemif_config aemif_configs[] = {
 
 int dram_init(void)
 {
-	ddr3_init();
+	u32 ddr3_size;
+
+	ddr3_size = ddr3_init();
 
 	gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE,
 				    CONFIG_MAX_RAM_BANK_SIZE);
 	aemif_init(ARRAY_SIZE(aemif_configs), aemif_configs);
-	ddr3_init_ecc(KS2_DDR3A_EMIF_CTRL_BASE);
+	ddr3_init_ecc(KS2_DDR3A_EMIF_CTRL_BASE, ddr3_size);
 	return 0;
 }
 
board/ti/ks2_evm/ddr3_k2e.c +6 -8
index 40fd966..35ffb42 100644
@@ -11,11 +11,11 @@
 #include "ddr3_cfg.h"
 #include <asm/arch/ddr3.h>
 
-static int ddr3_size;
 static struct pll_init_data ddr3_400 = DDR3_PLL_400;
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
+	u32 ddr3_size;
 	char dimm_name[32];
 
 	if (~(readl(KS2_PLL_CNTRL_BASE + KS2_RSTCTRL_RSTYPE) & 0x1))
@@ -43,13 +43,11 @@ void ddr3_init(void)
 		printf("DRAM: 4 GiB\n");
 		ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1600_4g);
 		ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_4g);
+	} else {
+		printf("Unknown SO-DIMM. Cannot configure DDR3\n");
+		while (1)
+			;
 	}
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
 	return ddr3_size;
 }
board/ti/ks2_evm/ddr3_k2hk.c +2 -9
index a1c3d05..b36eb27 100644
@@ -12,14 +12,13 @@
 #include <asm/arch/ddr3.h>
 #include <asm/arch/hardware.h>
 
-static int ddr3_size;
-
 struct pll_init_data ddr3a_333 = DDR3_PLL_333(A);
 struct pll_init_data ddr3a_400 = DDR3_PLL_400(A);
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
 	char dimm_name[32];
+	u32 ddr3_size;
 
 	ddr3_get_dimm_params(dimm_name);
 
@@ -93,12 +92,6 @@ void ddr3_init(void)
 	/* Apply the workaround for PG 1.0 and 1.1 Silicons */
 	if (cpu_revision() <= 1)
 		ddr3_err_reset_workaround();
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
 	return ddr3_size;
 }
board/ti/ks2_evm/ddr3_k2l.c +2 -10
index 15a14f2..00fc194 100644
@@ -11,28 +11,20 @@
 #include "ddr3_cfg.h"
 #include <asm/arch/ddr3.h>
 
-static int ddr3_size;
 static struct pll_init_data ddr3_400 = DDR3_PLL_400;
 
-void ddr3_init(void)
+u32 ddr3_init(void)
 {
 	init_pll(&ddr3_400);
 
 	/* No SO-DIMM, 2GB discreet DDR */
 	printf("DRAM: 2 GiB\n");
-	ddr3_size = 2;
 
 	/* Reset DDR3 PHY after PLL enabled */
 	ddr3_reset_ddrphy();
 
 	ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1600_2g);
 	ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_2g);
-}
 
-/**
- * ddr3_get_size - return ddr3 size in GiB
- */
-int ddr3_get_size(void)
-{
-	return ddr3_size;
+	return 2;
 }
Signature · 6 lines
1.9.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
Regards,
Nishanth Menon
#2 lore raw
In reply to Vitaly Andrianov
Quoted 9 lines · Vitaly Andrianov

KS2 ddr3 initialization uses ddr3_size global variable before u-boot relocation. Even if the variable is not being used after relocation, writing to it corrupts relocation table.

This patch removes the global ddr3_size variable and uses local one instead.

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150217/8dc85c8f/attachment.sig>