ARM: mvebu: add basic support for Armada 39x
Subsystems (9)
cover ARM: mvebu: add basic support for Armada 39x
Hello,
This set of patches add basic support for a new family of Marvell EBU
processors: the Armada 39x. They are based on Cortex-A9 (like Armada 375 and 38x) and the most important new feature is probably the addition of 10 GbE support.
See http://www.marvell.com/embedded-processors/armada-39x/ for a basic introduction.
Note that this web page talks about an Armada 395 and Armada 398, but so far the technical documentation we have been given access to only describes Armada 390 and Armada 398, so this series supports only Armada 390 and Armada 398 so far. Support for Armada 395 might be added in the future, once we get access to the appropriate technical details.
Besides this, this series should be relatively straightforward:
* Addition or update of various Device Tree binding documents
* Addition of clock support for Armada 39x
* Addition of pinctrl support for Armada 39x
* Core support and Device Tree for Armada 39x, with one Armada 398 Development Board supported
For now, the support is limited to a small subset of devices, we will enable more and more hardware blocks in the near future.
This branch is based on mvebu/for-next, and is obviously 3.21 material. Such an early posting is done to gather early review and feedback. I'll repost an updated series that takes into account the initial feedback once 3.20-rc1 lands.
Thanks,
Thomas Petazzoni
Thomas Petazzoni (10):
devicetree: bindings: add DT binding for the Marvell Armada 39x SoC
family
devicetree: bindings: update DT bindings for Marvell EBU clock support
devicetree: bindings: add Device Tree bindings for Armada 39x
pin-muxing controller
devicetree: bindings: add new SMP enable method for Marvell Armada 39x
clk: mvebu: extend common code to allow an optional refclk
clk: mvebu: add Marvell Armada 39x driver
pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
ARM: mvebu: add core support for Armada 39x
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
Documentation: arm: update supported Marvell EBU processors
Documentation/arm/Marvell/README | 5 + .../devicetree/bindings/arm/armada-39x.txt | 20 + Documentation/devicetree/bindings/arm/cpus.txt | 1 + .../devicetree/bindings/clock/mvebu-core-clock.txt | 9 + .../bindings/clock/mvebu-gated-clock.txt | 15 +- .../pinctrl/marvell,armada-39x-pinctrl.txt | 78 ++++ arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/armada-390.dtsi | 57 +++ arch/arm/boot/dts/armada-398-db.dts | 116 ++++++ arch/arm/boot/dts/armada-398.dtsi | 60 +++ arch/arm/boot/dts/armada-39x.dtsi | 372 ++++++++++++++++++ arch/arm/mach-mvebu/Kconfig | 14 + arch/arm/mach-mvebu/board-v7.c | 14 + arch/arm/mach-mvebu/platsmp-a9.c | 2 + drivers/clk/mvebu/Kconfig | 4 + drivers/clk/mvebu/Makefile | 1 + drivers/clk/mvebu/armada-39x.c | 156 ++++++++ drivers/clk/mvebu/common.c | 17 + drivers/clk/mvebu/common.h | 1 + drivers/pinctrl/mvebu/Kconfig | 4 + drivers/pinctrl/mvebu/Makefile | 1 + drivers/pinctrl/mvebu/pinctrl-armada-39x.c | 432 +++++++++++++++++++++ 22 files changed, 1380 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt create mode 100644 arch/arm/boot/dts/armada-390.dtsi create mode 100644 arch/arm/boot/dts/armada-398-db.dts create mode 100644 arch/arm/boot/dts/armada-398.dtsi create mode 100644 arch/arm/boot/dts/armada-39x.dtsi create mode 100644 drivers/clk/mvebu/armada-39x.c create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c
Signature · 1 line
2.1.0
PATCH 1/10 devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family
The Marvell Armada 39x is a family of two SoCs: the Armada 390 and the Armada 398, with a slightly different number of interfaces. This commit introduces the Device Tree binding that documents the top-level compatible strings for Armada 39x based platforms.
--- Documentation/devicetree/bindings/arm/armada-39x.txt | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt
Documentation/devicetree/bindings/arm/armada-39x.txt new file +20 -0
@@ -0,0 +1,20 @@ +Marvell Armada 39x Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 39x family shall have the +following property: + +Required root node property: + + - compatible: must contain "marvell,armada390" + +In addition, boards using the Marvell Armada 398 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada398" + +Example: + +compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
Signature · 1 line
2.1.0
PATCH 2/10 devicetree: bindings: update DT bindings for Marvell EBU clock support
In reply to Thomas PetazzoniWith the introduction of the Marvell Armada 39x SoC, the DT bindings for Marvell EBU clocks need to be extended. This commit include the corresponding update to the Device Tree bindings documentation.
--- .../devicetree/bindings/clock/mvebu-core-clock.txt | 9 +++++++++ .../devicetree/bindings/clock/mvebu-gated-clock.txt | 15 ++++++++++++++- 2 files changed, 23 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +9 -0
@@ -23,6 +23,14 @@ The following is a list of provided IDs and clock names on Armada 380/385: 2 = l2clk (L2 Cache clock) 3 = ddrclk (DDR clock) +The following is a list of provided IDs and clock names on Armada 39x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (Coherent Fabric clock) + 3 = hclk (SDRAM Controller Internal Clock) + 4 = dclk (SDRAM Interface Clock) + 5 = refclk (Reference Clock) + The following is a list of provided IDs and clock names on Kirkwood and Dove: 0 = tclk (Internal Bus clock) 1 = cpuclk (CPU0 clock)
@@ -39,6 +47,7 @@ Required properties: "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks + "marvell,armada-390-core-clock" - For Armada 39x SoC core clocks "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180)
Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +14 -1
@@ -1,6 +1,6 @@ * Gated Clock bindings for Marvell EBU SoCs -Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some +Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some peripheral clocks to be gated to save some power. The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to the
@@ -77,6 +77,18 @@ ID Clock Peripheral 28 xor1 XOR 1 30 sata1 SATA 1 +The following is a list of provided IDs for Armada 39x: +ID Clock Peripheral +----------------------------------- +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +17 sdio SDIO +22 xor0 XOR 0 +28 xor1 XOR 1 + The following is a list of provided IDs for Armada XP: ID Clock Peripheral -----------------------------------
@@ -152,6 +164,7 @@ Required properties: "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating + "marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating "marvell,dove-gating-clock" - for Dove SoC clock gating "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating
Signature · 1 line
2.1.0
PATCH 3/10 devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
In reply to Thomas PetazzoniThis commit adds the Device Tree binding documentation to describe the pin-muxing controller of the Marvell Armada 39x processors. Two variants are supported for the moment: the 88F6920 (Armada 390) and 88F6928 (Armada 398).
--- .../pinctrl/marvell,armada-39x-pinctrl.txt | 78 ++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt new file +78 -0
@@ -0,0 +1,78 @@ +* Marvell Armada 39x SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl" + depending on the specific variant of the SoC being used. +- reg: register specifier of MPP registers + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, ua0(rxd) +mpp1 1 gpio, ua0(txd) +mpp2 2 gpio, i2c0(sck) +mpp3 3 gpio, i2c0(sda) +mpp4 4 gpio, ua1(txd), ua0(rts), smi(mdc) +mpp5 5 gpio, ua1(rxd), ua0(cts), smi(mdio) +mpp6 6 gpio, dev(cs3), xsmi(mdio) +mpp7 7 gpio, dev(ad9), xsmi(mdc) +mpp8 8 gpio, dev(ad10), ptp(trig) +mpp9 9 gpio, dev(ad11), ptp(clk) +mpp10 10 gpio, dev(ad12), ptp(event) +mpp11 11 gpio, dev(ad13), led(clk) +mpp12 12 gpio, pcie0(rstout), dev(ad14), led(stb) +mpp13 13 gpio, dev(ad15), led(data) +mpp14 14 gpio, m(vtt), dev(wen1), ua1(txd) +mpp15 15 gpio, pcie0(rstout), spi0(mosi), i2c1(sck) +mpp16 16 gpio, m(decc), spi0(miso), i2c1(sda) +mpp17 17 gpio, ua1(rxd), spi0(sck), smi(mdio) +mpp18 18 gpio, ua1(txd), spi0(cs0), i2c2(sck) +mpp19 19 gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda) +mpp20 20 gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc) +mpp21 21 gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0) +mpp22 22 gpio, spi0(mosi), dev(ad0) +mpp23 23 gpio, spi0(sck), dev(ad2) +mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn) +mpp25 25 gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0) +mpp26 26 gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1) +mpp27 27 gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout) +mpp28 28 gpio, sd(clk), dev(ad5), ge(txd0) +mpp29 29 gpio, dev(ale0), ge(txd1) +mpp30 30 gpio, dev(oen), ge(txd2) +mpp31 31 gpio, dev(ale1), ge(txd3) +mpp32 32 gpio, dev(wen0), ge(txctl) +mpp33 33 gpio, m(decc), dev(ad3) +mpp34 34 gpio, dev(ad1) +mpp35 35 gpio, ref(clk), dev(a1) +mpp36 36 gpio, dev(a0) +mpp37 37 gpio, sd(d3), dev(ad8), ge(rxclk) +mpp38 38 gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1) +mpp39 39 gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2) +mpp40 40 gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3) +mpp41 41 gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl) +mpp42 42 gpio, ua1(txd), ua0(rts), dev(ad7) +mpp43 43 gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1) +mpp44 44 gpio, sata0(present) [1], sata1(present) [1], led(clk) +mpp45 45 gpio, ref(clk), pcie0(rstout), ua1(rxd) +mpp46 46 gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb) +mpp47 47 gpio, sata0(present) [1], sata1(present) [1], led(data) +mpp48 48 gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd) +mpp49 49 gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd) +mpp50 50 gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd) +mpp51 51 gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd) +mpp52 52 gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck) +mpp53 53 gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda) +mpp54 54 gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd) +mpp55 55 gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd) +mpp56 56 gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd) +mpp57 57 gpio, spi1(sck), sd(clk), ua1(txd) +mpp58 58 gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd) +mpp59 59 gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2) + +[1]: only available on 88F6928
Signature · 1 line
2.1.0
Andrew Lunn
maintainerPATCH 3/10 devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
Quoted 33 lines · Thomas Petazzoni
This commit adds the Device Tree binding documentation to describe the pin-muxing controller of the Marvell Armada 39x processors. Two variants are supported for the moment: the 88F6920 (Armada 390) and 88F6928 (Armada 398).
Signed-off-by Thomas Petazzoni <[email protected]>--- .../pinctrl/marvell,armada-39x-pinctrl.txt | 78 ++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txtDocumentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt new file +16
-0@@ -0,0 +1,78 @@ +* Marvell Armada 39x SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl" + depending on the specific variant of the SoC being used. +- reg: register specifier of MPP registers + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================
Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt line 26
Quoted 10 lines
Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt new file +10
-0+mpp0 0 gpio, ua0(rxd) +mpp1 1 gpio, ua0(txd) +mpp2 2 gpio, i2c0(sck) +mpp3 3 gpio, i2c0(sda) +mpp4 4 gpio, ua1(txd), ua0(rts), smi(mdc) +mpp5 5 gpio, ua1(rxd), ua0(cts), smi(mdio) +mpp6 6 gpio, dev(cs3), xsmi(mdio) +mpp7 7 gpio, dev(ad9), xsmi(mdc) +mpp8 8 gpio, dev(ad10), ptp(trig) +mpp9 9 gpio, dev(ad11), ptp(clk)
Hi Thomas
I wondering if there should be an explanation for the less common names here. I'm guessing dev is a device bus of some sort? What is xsmi? Some sort of extended System Management Interface? And m?
Thanks
Andrewy
Quoted 55 lines
Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt new file +52
-0+mpp10 10 gpio, dev(ad12), ptp(event) +mpp11 11 gpio, dev(ad13), led(clk) +mpp12 12 gpio, pcie0(rstout), dev(ad14), led(stb) +mpp13 13 gpio, dev(ad15), led(data) +mpp14 14 gpio, m(vtt), dev(wen1), ua1(txd) +mpp15 15 gpio, pcie0(rstout), spi0(mosi), i2c1(sck) +mpp16 16 gpio, m(decc), spi0(miso), i2c1(sda) +mpp17 17 gpio, ua1(rxd), spi0(sck), smi(mdio) +mpp18 18 gpio, ua1(txd), spi0(cs0), i2c2(sck) +mpp19 19 gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda) +mpp20 20 gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc) +mpp21 21 gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0) +mpp22 22 gpio, spi0(mosi), dev(ad0) +mpp23 23 gpio, spi0(sck), dev(ad2) +mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn) +mpp25 25 gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0) +mpp26 26 gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1) +mpp27 27 gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout) +mpp28 28 gpio, sd(clk), dev(ad5), ge(txd0) +mpp29 29 gpio, dev(ale0), ge(txd1) +mpp30 30 gpio, dev(oen), ge(txd2) +mpp31 31 gpio, dev(ale1), ge(txd3) +mpp32 32 gpio, dev(wen0), ge(txctl) +mpp33 33 gpio, m(decc), dev(ad3) +mpp34 34 gpio, dev(ad1) +mpp35 35 gpio, ref(clk), dev(a1) +mpp36 36 gpio, dev(a0) +mpp37 37 gpio, sd(d3), dev(ad8), ge(rxclk) +mpp38 38 gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1) +mpp39 39 gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2) +mpp40 40 gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3) +mpp41 41 gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl) +mpp42 42 gpio, ua1(txd), ua0(rts), dev(ad7) +mpp43 43 gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1) +mpp44 44 gpio, sata0(present) [1], sata1(present) [1], led(clk) +mpp45 45 gpio, ref(clk), pcie0(rstout), ua1(rxd) +mpp46 46 gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb) +mpp47 47 gpio, sata0(present) [1], sata1(present) [1], led(data) +mpp48 48 gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd) +mpp49 49 gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd) +mpp50 50 gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd) +mpp51 51 gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd) +mpp52 52 gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck) +mpp53 53 gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda) +mpp54 54 gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd) +mpp55 55 gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd) +mpp56 56 gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd) +mpp57 57 gpio, spi1(sck), sd(clk), ua1(txd) +mpp58 58 gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd) +mpp59 59 gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2) + +[1]: only available on 88F6928Signature · 1 line
2.1.0
PATCH 3/10 devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
Dear Andrew Lunn,
Quoted 3 lines · Andrew Lunn
I wondering if there should be an explanation for the less common names here. I'm guessing dev is a device bus of some sort? What is xsmi? Some sort of extended System Management Interface? And m?
"dev" is the Device Bus indeed, used for example for NOR or NAND.
"m" stands for memory. The m(decc) signal is asserted when a memory ECC error occurred, while the m(vtt) signal is the DRAM VTT Power Control signal. No idea what this is.
"xsmi" is indeed some other SMI bus, not clear yet how it compares to the regular SMI bus.
Both "dev" and "m" are already used by many of the existing pinctrl DT bindings for Marvell platforms, so I'm not sure documenting them specifically in the Armada 39x pinctrl DT binding document makes a lot of sense. Where should we document them, then? In the generic 'marvell,mvebu-pinctrl.txt' DT binding file ?
Best regards,
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH 3/10 devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
Quoted 5 lines
Both "dev" and "m" are already used by many of the existing pinctrl DT bindings for Marvell platforms, so I'm not sure documenting them specifically in the Armada 39x pinctrl DT binding document makes a lot of sense. Where should we document them, then? In the generic 'marvell,mvebu-pinctrl.txt' DT binding file ?
Hi Thomas
Yes, that would be a good place to list them.
Thanks
Andrew
PATCH 4/10 devicetree: bindings: add new SMP enable method for Marvell Armada 39x
In reply to Thomas PetazzoniThis commit updates the ARM CPUs Device Tree binding to document a new enable method of Marvell Armada 39x processors.
--- Documentation/devicetree/bindings/arm/cpus.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/cpus.txt +1 -0
@@ -191,6 +191,7 @@ nodes to be present and contain the properties described below. "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" + "marvell,armada-390-smp" "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1"
Signature · 1 line
2.1.0
PATCH 5/10 clk: mvebu: extend common code to allow an optional refclk
In reply to Thomas PetazzoniThe Armada 39x, contrary to its predecessor, has a configurable reference clock frequency, of either 25 Mhz, or 40 Mhz. For the previous SoCs, it was fixed to 25 Mhz and described directly as such in the Device Tree.
For Armada 39x, we need to read certain registers to know whether the frequency is 25 or 40 Mhz. Therefore, this commit extends the common mvebu clock code to allow the SoC-specific code to say it wants to register a reference clock, by giving a non-NULL ->get_refclk_freq() function pointer in its coreclk_soc_desc structure.
--- drivers/clk/mvebu/common.c | 17 +++++++++++++++++ drivers/clk/mvebu/common.h | 1 + 2 files changed, 18 insertions(+)
drivers/clk/mvebu/common.c +17 -0
@@ -121,6 +121,11 @@ void __init mvebu_coreclk_setup(struct device_node *np,/* Allocate struct for TCLK, cpu clk, and core ratio clocks */ clk_data.clk_num =2 + desc->num_ratios; + +/* One more clock for the optional refclk */ +if (desc->get_refclk_freq) + clk_data.clk_num +=1 ; + clk_data.clks =kzalloc (clk_data.clk_num *sizeof (struct clk *),GFP_KERNEL );if (WARN_ON (!clk_data.clks)) {
@@ -162,6 +167,18 @@ void __init mvebu_coreclk_setup(struct device_node *np,WARN_ON (IS_ERR (clk_data.clks[2 +n])); }; +/* Register optional refclk */ +if (desc->get_refclk_freq) { +const char *name ="refclk" ; +of_property_read_string_index (np,"clock-output-names" , +2 + desc->num_ratios, &name); + rate = desc->get_refclk_freq (base); + clk_data.clks[2 + desc->num_ratios] = +clk_register_fixed_rate (NULL , name,NULL , +CLK_IS_ROOT , rate); +WARN_ON (IS_ERR (clk_data.clks[2 + desc->num_ratios])); + } +/* SAR register isn't needed anymore */ iounmap (base);
drivers/clk/mvebu/common.h +1 -0
@@ -30,6 +30,7 @@ struct coreclk_soc_desc {u32 (*get_tclk_freq)(void__iomem *sar);u32 (*get_cpu_freq)(void__iomem *sar);void (*get_clk_ratio)(void __iomem *sar,int id,int *mult,int *div); +u32 (*get_refclk_freq)(void__iomem *sar);bool (*is_sscg_enabled)(void __iomem *sar);u32 (*fix_sscg_deviation)(u32 system_clk);const struct coreclk_ratio *ratios;
Signature · 1 line
2.1.0
PATCH 6/10 clk: mvebu: add Marvell Armada 39x driver
In reply to Thomas PetazzoniThis commit adds a new clock driver for the Marvell Armada 39x family of processors. This driver is fairly similar to the ones already used on other Marvell EBU processors, with the following main differences:
* Different set of ratios
* Different set of core clocks
* Configurable reference clock in frequency
--- drivers/clk/mvebu/Kconfig | 4 ++ drivers/clk/mvebu/Makefile | 1 + drivers/clk/mvebu/armada-39x.c | 156 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 161 insertions(+) create mode 100644 drivers/clk/mvebu/armada-39x.c
drivers/clk/mvebu/Kconfig +4 -0
@@ -21,6 +21,10 @@ config ARMADA_38X_CLK bool select MVEBU_CLK_COMMON +config ARMADA_39X_CLK + bool + select MVEBU_CLK_COMMON + config ARMADA_XP_CLK bool select MVEBU_CLK_COMMON
drivers/clk/mvebu/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_MVEBU_CLK_COREDIV) += clk-corediv.o obj-$(CONFIG_ARMADA_370_CLK) += armada-370.o obj-$(CONFIG_ARMADA_375_CLK) += armada-375.o obj-$(CONFIG_ARMADA_38X_CLK) += armada-38x.o +obj-$(CONFIG_ARMADA_39X_CLK) += armada-39x.o obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o obj-$(CONFIG_DOVE_CLK) += dove.o obj-$(CONFIG_KIRKWOOD_CLK) += kirkwood.o
drivers/clk/mvebu/armada-39x.c new file +156 -0
156 lines not on this page · raw message
Signature · 1 line
2.1.0
PATCH 7/10 pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
In reply to Thomas PetazzoniThis commit adds a new pinctrl driver for the Marvell Armada 39x family of processors, which hooks into the existing infrastructure to support pin-muxing on Marvell EBU processors. Two variants of the Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada 398), which have a few differences in the available functions for certain pins.
--- drivers/pinctrl/mvebu/Kconfig | 4 + drivers/pinctrl/mvebu/Makefile | 1 + drivers/pinctrl/mvebu/pinctrl-armada-39x.c | 432 +++++++++++++++++++++++++++++ 3 files changed, 437 insertions(+) create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c
drivers/pinctrl/mvebu/Kconfig +4 -0
@@ -26,6 +26,10 @@ config PINCTRL_ARMADA_38X bool select PINCTRL_MVEBU +config PINCTRL_ARMADA_39X + bool + select PINCTRL_MVEBU + config PINCTRL_ARMADA_XP bool select PINCTRL_MVEBU
drivers/pinctrl/mvebu/Makefile +1 -0
@@ -4,5 +4,6 @@ obj-$(CONFIG_PINCTRL_KIRKWOOD) += pinctrl-kirkwood.o obj-$(CONFIG_PINCTRL_ARMADA_370) += pinctrl-armada-370.o obj-$(CONFIG_PINCTRL_ARMADA_375) += pinctrl-armada-375.o obj-$(CONFIG_PINCTRL_ARMADA_38X) += pinctrl-armada-38x.o +obj-$(CONFIG_PINCTRL_ARMADA_39X) += pinctrl-armada-39x.o obj-$(CONFIG_PINCTRL_ARMADA_XP) += pinctrl-armada-xp.o obj-$(CONFIG_PINCTRL_ORION) += pinctrl-orion.o
drivers/pinctrl/mvebu/pinctrl-armada-39x.c new file +432 -0
432 lines not on this page · raw message
Signature · 1 line
2.1.0
PATCH 7/10 pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
Quoted 8 lines · Thomas Petazzoni
This commit adds a new pinctrl driver for the Marvell Armada 39x family of processors, which hooks into the existing infrastructure to support pin-muxing on Marvell EBU processors. Two variants of the Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada 398), which have a few differences in the available functions for certain pins.
Signed-off-by Thomas Petazzoni <[email protected]>
Patch applied.
Yours,
Linus Walleij
PATCH 7/10 pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
Dear Linus Walleij,
Quoted 10 lines · Linus Walleij
Quoted 7 lines · Thomas Petazzoni
This commit adds a new pinctrl driver for the Marvell Armada 39x family of processors, which hooks into the existing infrastructure to support pin-muxing on Marvell EBU processors. Two variants of the Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada 398), which have a few differences in the available functions for certain pins.
Quoted 3 lines
Quoted 1 line
Signed-off-by Thomas Petazzoni <[email protected]>Patch applied.
I'm surprised you applied the driver of the first iteration of the patches, and not the v3 I sent just yesterday. Even though if I remember correctly there were no changes on the pinctrl driver itself.
Also, can you apply:
devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
Thanks!
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
PATCH 8/10 ARM: mvebu: add core support for Armada 39x
In reply to Thomas PetazzoniThis commit adds the core support for Armada 39x, which is quite simple:
- a new Kconfig option which selects the appropriate clock and pinctrl drivers as well as other common features (GIC, L2 cache, SMP, etc.)
- a new DT_MACHINE_START which references the top-level compatible strings supported for the Marvell Armada 39x.
- a new SMP enable-method. The mechanism to enable CPUs for Armada 39x appears to be the same as Armada 38x. However, we do want to use marvell,armada-380-smp in the Device Tree, in the case of the discovery of a subtle difference in the future, which would require changing the Device Tree. And the enable-method isn't a compatible
string: you can't specify several values and expect a fallback on the second string if the first one isn't supported. Therefore, we simply declare the SMP enable method "marvell,armada-390-smp" as doing the same thing as the "marvell,armada-380-smp" one.
--- arch/arm/mach-mvebu/Kconfig | 14 ++++++++++++++ arch/arm/mach-mvebu/board-v7.c | 14 ++++++++++++++ arch/arm/mach-mvebu/platsmp-a9.c | 2 ++ 3 files changed, 30 insertions(+)
arch/arm/mach-mvebu/Kconfig +14 -0
@@ -64,6 +64,20 @@ config MACH_ARMADA_38X Say 'Y' here if you want your kernel to support boards based on the Marvell Armada 380/385 SoC with device tree. +config MACH_ARMADA_39X + bool "Marvell Armada 39x boards" if ARCH_MULTI_V7 + select ARM_GIC + select ARMADA_39X_CLK + select CACHE_L2X0 + select HAVE_ARM_SCU + select HAVE_ARM_TWD if SMP + select HAVE_SMP + select MACH_MVEBU_V7 + select PINCTRL_ARMADA_39X + help + Say 'Y' here if you want your kernel to support boards based + on the Marvell Armada 39x SoC with device tree. + config MACH_ARMADA_XP bool "Marvell Armada XP boards" if ARCH_MULTI_V7 select ARMADA_XP_CLK
arch/arm/mach-mvebu/board-v7.c +14 -0
@@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)") .restart = mvebu_restart, .dt_compat = armada_38x_dt_compat, MACHINE_END + +static const char * const armada_39x_dt_compat[] = { +"marvell,armada390" , +"marvell,armada398" , +NULL , +}; + +DT_MACHINE_START (ARMADA_39X_DT ,"Marvell Armada 39x (Device Tree)" ) + .l2c_aux_val = 0, + .l2c_aux_mask = ~0, + .init_irq = mvebu_init_irq, + .restart = mvebu_restart, + .dt_compat = armada_39x_dt_compat, +MACHINE_END
arch/arm/mach-mvebu/platsmp-a9.c +2 -0
@@ -110,3 +110,5 @@ CPU_METHOD_OF_DECLARE(mvebu_armada_375_smp, "marvell,armada-375-smp", &mvebu_cortex_a9_smp_ops);CPU_METHOD_OF_DECLARE (mvebu_armada_380_smp,"marvell,armada-380-smp" , &armada_38x_smp_ops); +CPU_METHOD_OF_DECLARE (mvebu_armada_390_smp,"marvell,armada-390-smp" , + &armada_38x_smp_ops);
Signature · 1 line
2.1.0
PATCH 8/10 ARM: mvebu: add core support for Armada 39x
arch/arm/mach-mvebu/board-v7.c DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)") · line 236
Quoted 10 lines · Thomas Petazzoni
arch/arm/mach-mvebu/board-v7.c +2
-0@@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)") .restart = mvebu_restart, .dt_compat = armada_38x_dt_compat,MACHINE_END + +static const char * const armada_39x_dt_compat[] = {
__initconst?
Quoted 13 lines
arch/arm/mach-mvebu/board-v7.c +12
-0+"marvell,armada390" , +"marvell,armada398" , +NULL , +}; + +DT_MACHINE_START (ARMADA_39X_DT ,"Marvell Armada 39x (Device Tree)" ) + .l2c_aux_val =0 , + .l2c_aux_mask = ~0, + .init_irq = mvebu_init_irq, + .restart = mvebu_restart, + .dt_compat = armada_39x_dt_compat, +MACHINE_END
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH 8/10 ARM: mvebu: add core support for Armada 39x
Dear Stephen Boyd,
Quoted 3 lines · Stephen Boyd
Quoted 1 line
+static const char * const armada_39x_dt_compat[] = {
__initconst?
Good idea. This wasn't done for the other mach-mvebu dt_compat tables, so I've added a patch to do this as well for the other mach-mvebu dt_compat tables.
Will be in v2.
Thanks!
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
PATCH 8/10 ARM: mvebu: add core support for Armada 39x
In reply to Thomas PetazzoniHi Thomas,
Quoted 7 lines · Thomas Petazzoni
This commit adds the core support for Armada 39x, which is quite simple:
- a new
Kconfigoption which selects the appropriate clock and pinctrl drivers as well as other common features (GIC, L2 cache, SMP, etc.)
Quoted 5 lines
- a new
DT_MACHINE_STARTwhich references the top-level compatible strings supported for the Marvell Armada 39x.- a new SMP enable-method. The mechanism to enable CPUs for Armada 39x appears to be the same as Armada 38x. However, we do want to
^ not?
Quoted 8 lines
use marvell,armada-380-smp in the Device Tree, in the case of the discovery of a subtle difference in the future, which would require changing the Device Tree. And the enable-method isn't a compatible
string: you can't specify several values and expect a fallback on the second string if the first one isn't supported. Therefore, we simply declare the SMP enable method "marvell,armada-390-smp" as doing the same thing as the "marvell,armada-380-smp" one.
Maxime
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150206/562eab45/attachment.sig>
PATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
In reply to Thomas PetazzoniThis commit adds the Device Tree files for the Armada 39x family of processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains the description of the common features of all Armada 39x SoCs, while armada-390.dtsi and armada-398.dtsi respectively describe the specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398 Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus controller, MPIC interrupt controller, timer, CPU reset for SMP, PMSU.
* I2C
* UART
* PCIe
Additional features will be supported in the future.
--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/armada-390.dtsi | 57 ++++++ arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++ arch/arm/boot/dts/armada-398.dtsi | 60 ++++++ arch/arm/boot/dts/armada-39x.dtsi | 372 ++++++++++++++++++++++++++++++++++++ 5 files changed, 607 insertions(+) create mode 100644 arch/arm/boot/dts/armada-390.dtsi create mode 100644 arch/arm/boot/dts/armada-398-db.dts create mode 100644 arch/arm/boot/dts/armada-398.dtsi create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
arch/arm/boot/dts/Makefile +2 -0
@@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_39X) += \ + armada-398-db.dtb dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \
arch/arm/boot/dts/armada-390.dtsi new file +57 -0
57 lines not on this page · raw message
arch/arm/boot/dts/armada-398-db.dts new file +116 -0
116 lines not on this page · raw message
arch/arm/boot/dts/armada-398.dtsi new file +60 -0
60 lines not on this page · raw message
arch/arm/boot/dts/armada-39x.dtsi new file +372 -0
372 lines not on this page · raw message
Signature · 1 line
2.1.0
Andrew Lunn
maintainerPATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
Quoted 166 lines · Thomas Petazzoni
This commit adds the Device Tree files for the Armada 39x family of processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common
armada-39x.dtsicontains the description of the common features of all Armada 39x SoCs, whilearmada-390.dtsiandarmada-398.dtsirespectively describe the specificities of those SoCs.Finally, an
armada-398-db.dtsfile is added to describe the Armada 398 Development Board itself.So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus controller, MPIC interrupt controller, timer, CPU reset for SMP, PMSU.
* I2C
* UART
* PCIeAdditional features will be supported in the future.
Signed-off-by Thomas Petazzoni <[email protected]>--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/armada-390.dtsi | 57 ++++++ arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++ arch/arm/boot/dts/armada-398.dtsi | 60 ++++++ arch/arm/boot/dts/armada-39x.dtsi | 372 ++++++++++++++++++++++++++++++++++++ 5 files changed, 607 insertions(+) create mode 100644 arch/arm/boot/dts/armada-390.dtsi create mode 100644 arch/arm/boot/dts/armada-398-db.dts create mode 100644 arch/arm/boot/dts/armada-398.dtsi create mode 100644 arch/arm/boot/dts/armada-39x.dtsiarch/arm/boot/dts/Makefile +2
-0@@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_39X) += \ + armada-398-db.dtb dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \arch/arm/boot/dts/armada-390.dtsi new file +57
-0@@ -0,0 +1,57 @@ +/* + * Device Tree Include file for Marvell Armada 390 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + soc { + internal-regs { + pinctrl at 18000 { + compatible = "marvell,mv88f6920-pinctrl"; + reg = <0x18000 0x20>; + }; + }; +};arch/arm/boot/dts/armada-398-db.dts new file +47
-0@@ -0,0 +1,116 @@ +/* + * Device Tree Include file for Marvell Armada 398 Development Board + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/;
arch/arm/boot/dts/armada-398-db.dts line 57
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+#include "armada-398.dtsi" + +/ { + model = "Marvell Armada 398 Development Board"; + compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; +
Arnd has been encouraging people not use earlyprintk here. Also a stdout-path would be nice. We also seem to be missing aliases for the serial ports.
Quoted 13 lines
arch/arm/boot/dts/armada-398-db.dts new file +13
-0+ memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + i2c at 11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default";
arch/arm/boot/dts/armada-398-db.dts line 80
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+ status = "okay"; + clock-frequency = <100000>; + }; + + serial at 12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; +
Tab vs space issue here somewhere? Probably the i2c node.
Quoted 6 lines
arch/arm/boot/dts/armada-398-db.dts new file +6
-0+ serial at 12100 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; +
arch/arm/boot/dts/armada-398-db.dts line 96
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+ pinctrl at 18000 { + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; + + uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + };
Does it make sense to put there in the .dtsi file? I know there are other choices, but generally board manufacturers tend to follow the reference design.
Andrew
Quoted 467 lines
arch/arm/boot/dts/armada-398-db.dts new file +20
-0+ }; + }; + + pcie-controller { + status = "okay"; + + pcie at 1,0 { + status = "okay"; + }; + + pcie at 2,0 { + status = "okay"; + }; + + pcie at 3,0 { + status = "okay"; + }; + }; + }; +};arch/arm/boot/dts/armada-398.dtsi new file +60
-0@@ -0,0 +1,60 @@ +/* + * Device Tree Include file for Marvell Armada 398 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + compatible = "marvell,armada398", "marvell,armada390"; + + soc { + internal-regs { + pinctrl at 18000 { + compatible = "marvell,mv88f6928-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + }; +};arch/arm/boot/dts/armada-39x.dtsi new file +372
-0@@ -0,0 +1,372 @@ +/* + * Device Tree Include file for Marvell Armada 39x family of SoCs. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 39x family SoC"; + compatible = "marvell,armada390"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "marvell,armada-390-smp"; + + cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + scu at c000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xc000 0x100>; + }; + + timer at c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller at d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + i2c0: i2c at 11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c at 11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c2: i2c at 11200 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11200 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c3: i2c at 11300 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11300 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12200 { + compatible = "snps,dw-apb-uart"; + reg = <0x12200 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12300 { + compatible = "snps,dw-apb-uart"; + reg = <0x12300 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + pinctrl at 18000 { + i2c0_pins: i2c0-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c0"; + }; + }; + + system-controller at 18200 { + compatible = "marvell,armada-390-system-controller", + "marvell,armada-370-xp-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control at 18220 { + compatible = "marvell,armada-390-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + coreclk: mvebu-sar at 18600 { + compatible = "marvell,armada-390-core-clock"; + reg = <0x18600 0x04>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller at 20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; + }; + + mpic: interrupt-controller at 20000 { + compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer at 20300 { + compatible = "marvell,armada-380-timer", + "marvell,armada-xp-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 2>, <&coreclk 5>; + clock-names = "nbclk", "fixed"; + }; + + cpurst at 20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x10>; + }; + + pmsu at 22000 { + compatible = "marvell,armada-390-pmsu", + "marvell,armada-380-pmsu"; + reg = <0x22000 0x1000>; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>; + + /* + * This port can be either x4 or x1. When + * configured in x4 by the bootloader, then + * pcie at 4,0 is not available. + */ + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie at 2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie at 3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + /* + * x1 port only available when pcie at 1,0 is + * configured as a x1 port + */ + pcie at 4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + }; + }; +};Signature · 1 line
2.1.0
PATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
Dear Andrew Lunn,
Quoted 8 lines · Andrew Lunn
arch/arm/boot/dts/armada-398-db.dts line 57
Quoted 4 lines
arch/arm/boot/dts/armada-398-db.dts new file +4
-0+ chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; +Arnd has been encouraging people not use earlyprintk here. Also a stdout-path would be nice. We also seem to be missing aliases for the serial ports.
Right.
Quoted 8 lines
Quoted 8 lines
arch/arm/boot/dts/armada-398-db.dts new file +8
-0+ internal-regs { + i2c at 11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + clock-frequency = <100000>; + }; +
Quoted 8 lines
arch/arm/boot/dts/armada-398-db.dts line 80
Quoted 6 lines
arch/arm/boot/dts/armada-398-db.dts new file +6
-0+ serial at 12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; +Tab vs space issue here somewhere? Probably the i2c node.
Yes, fixed.
Quoted 6 lines
Quoted 6 lines
arch/arm/boot/dts/armada-398-db.dts new file +6
-0+ pinctrl at 18000 { + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; +
Quoted 8 lines
arch/arm/boot/dts/armada-398-db.dts line 96
Quoted 4 lines
arch/arm/boot/dts/armada-398-db.dts new file +4
-0+ uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + };Does it make sense to put there in the .dtsi file? I know there are other choices, but generally board manufacturers tend to follow the reference design.
I am not really convinced here: there are really many possible pin muxing possibilities. Various pins for UART0 and UART1, whether you use CTS/RTS or not, etc. I believe this is really the sort of pin mux configuration that is best left at the board level.
Best regards,
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
Andrew Lunn
maintainerPATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
Quoted 15 lines
Quoted 6 lines
Quoted 6 lines
arch/arm/boot/dts/armada-398-db.dts new file +6
-0+ pinctrl at 18000 { + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; +Quoted 8 lines
arch/arm/boot/dts/armada-398-db.dts line 96
Quoted 4 lines
arch/arm/boot/dts/armada-398-db.dts new file +4
-0+ uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + };Does it make sense to put there in the .dtsi file? I know there are other choices, but generally board manufacturers tend to follow the reference design.
Quoted 4 lines
I am not really convinced here: there are really many possible pin muxing possibilities. Various pins for UART0 and UART1, whether you use CTS/RTS or not, etc. I believe this is really the sort of pin mux configuration that is best left at the board level.
Hi Thomas
Lets look at this from the perspective of lies, damn lies, and statistics:
Kirkwood has a default pinmux configuration in kirkwood.dtsi. Two of the sixty six .dts files overwrite the defaults.
Dove has a default pinmux of uart1, but none for uart0. None of the .dts files define a pinmux for uart0 and none overwrite the defaults for uart1.
Armanda XP has a default pinmux for uart2 and uart2 in armada-xp.dtsi, but none for uart0 or uart1. None of the .dts files define a pinmux for uart0 or uart1, and none overwrite the defaults for uart2 or uart3.
Armada 370 has default pinmux for uart0 and uart1. None of the .dts files overwrite the defaults.
I'm too lazy to look at 375, 380, and 385.
We have over 80 dts files here with defaults from a .dtsi file, and only two need anything other than defaults.
Andrew
PATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
Dear Andrew Lunn,
Quoted 15 lines · Andrew Lunn
Lets look at this from the perspective of lies, damn lies, and statistics:
Kirkwood has a default pinmux configuration in
kirkwood.dtsi. Two of the sixty six .dts files overwrite the defaults.Dove has a default pinmux of uart1, but none for uart0. None of the .dts files define a pinmux for uart0 and none overwrite the defaults for uart1.
Armanda XP has a default pinmux for uart2 and uart2 in
armada-xp.dtsi, but none for uart0 or uart1. None of the .dts files define a pinmux for uart0 or uart1, and none overwrite the defaults for uart2 or uart3.
Quoted 7 lines
Armada 370 has default pinmux for uart0 and uart1. None of the .dts files overwrite the defaults.
I'm too lazy to look at 375, 380, and 385.
We have over 80 dts files here with defaults from a .dtsi file, and only two need anything other than defaults.
Fair enough :)
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
PATCH 9/10 ARM: mvebu: add Device Tree files for Armada 39x SoC and board
In reply to Thomas PetazzoniQuoted 164 lines · Thomas Petazzoni
This commit adds the Device Tree files for the Armada 39x family of processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common
armada-39x.dtsicontains the description of the common features of all Armada 39x SoCs, whilearmada-390.dtsiandarmada-398.dtsirespectively describe the specificities of those SoCs.Finally, an
armada-398-db.dtsfile is added to describe the Armada 398 Development Board itself.So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus controller, MPIC interrupt controller, timer, CPU reset for SMP, PMSU.
* I2C
* UART
* PCIeAdditional features will be supported in the future.
Signed-off-by Thomas Petazzoni <[email protected]>--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/armada-390.dtsi | 57 ++++++ arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++ arch/arm/boot/dts/armada-398.dtsi | 60 ++++++ arch/arm/boot/dts/armada-39x.dtsi | 372 ++++++++++++++++++++++++++++++++++++ 5 files changed, 607 insertions(+) create mode 100644 arch/arm/boot/dts/armada-390.dtsi create mode 100644 arch/arm/boot/dts/armada-398-db.dts create mode 100644 arch/arm/boot/dts/armada-398.dtsi create mode 100644 arch/arm/boot/dts/armada-39x.dtsiarch/arm/boot/dts/Makefile +2
-0@@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_39X) += \ + armada-398-db.dtb dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \arch/arm/boot/dts/armada-390.dtsi new file +57
-0@@ -0,0 +1,57 @@ +/* + * Device Tree Include file for Marvell Armada 390 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + soc { + internal-regs { + pinctrl at 18000 { + compatible = "marvell,mv88f6920-pinctrl"; + reg = <0x18000 0x20>; + }; + }; +};arch/arm/boot/dts/armada-398-db.dts new file +45
-0@@ -0,0 +1,116 @@ +/* + * Device Tree Include file for Marvell Armada 398 Development Board + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */
arch/arm/boot/dts/armada-398-db.dts line 55
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+ +/dts-v1/; +#include "armada-398.dtsi" + +/ { + model = "Marvell Armada 398 Development Board"; + compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk";
I think Arnd wanted to remove all the earlyprintk here, just in case the debug_ll options compiled in the kernel would not match the board/SoC options.
Quoted 7 lines
arch/arm/boot/dts/armada-398-db.dts new file +7
-0+ }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; +
arch/arm/boot/dts/armada-398-db.dts line 72
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+ soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + i2c at 11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + clock-frequency = <100000>;
The indentation looks off here.
It seems like you indented the two first lines with tabs, and the two last with spaces.
Quoted 14 lines
arch/arm/boot/dts/armada-398-db.dts new file +14
-0+ }; + + serial at 12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial at 12100 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; +
arch/arm/boot/dts/armada-398-db.dts line 96
Quoted 10 lines
arch/arm/boot/dts/armada-398-db.dts new file +10
-0+ pinctrl at 18000 { + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; + + uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + };
These two looks like generic muxing options, maybe they should be put in the SoC DTSI?
Quoted 313 lines
arch/arm/boot/dts/armada-398-db.dts new file +20
-0+ }; + }; + + pcie-controller { + status = "okay"; + + pcie at 1,0 { + status = "okay"; + }; + + pcie at 2,0 { + status = "okay"; + }; + + pcie at 3,0 { + status = "okay"; + }; + }; + }; +};arch/arm/boot/dts/armada-398.dtsi new file +60
-0@@ -0,0 +1,60 @@ +/* + * Device Tree Include file for Marvell Armada 398 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + compatible = "marvell,armada398", "marvell,armada390"; + + soc { + internal-regs { + pinctrl at 18000 { + compatible = "marvell,mv88f6928-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + }; +};arch/arm/boot/dts/armada-39x.dtsi new file +221
-0@@ -0,0 +1,372 @@ +/* + * Device Tree Include file for Marvell Armada 39x family of SoCs. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 39x family SoC"; + compatible = "marvell,armada390"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "marvell,armada-390-smp"; + + cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + scu at c000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xc000 0x100>; + }; + + timer at c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller at d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + i2c0: i2c at 11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c at 11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c2: i2c at 11200 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11200 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c3: i2c at 11300 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11300 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12200 { + compatible = "snps,dw-apb-uart"; + reg = <0x12200 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial at 12300 { + compatible = "snps,dw-apb-uart"; + reg = <0x12300 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + pinctrl at 18000 { + i2c0_pins: i2c0-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c0"; + }; + }; + + system-controller at 18200 { + compatible = "marvell,armada-390-system-controller", + "marvell,armada-370-xp-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control at 18220 { + compatible = "marvell,armada-390-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + coreclk: mvebu-sar at 18600 { + compatible = "marvell,armada-390-core-clock";
arch/arm/boot/dts/armada-39x.dtsi line 231
Quoted 10 lines
arch/arm/boot/dts/armada-39x.dtsi new file +10
-0+ reg = <0x18600 0x04>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller at 20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; + }; + + mpic: interrupt-controller at 20000 {
The unit-address doesn't match the reg address.
Quoted 144 lines
arch/arm/boot/dts/armada-39x.dtsi new file +141
-0+ compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer at 20300 { + compatible = "marvell,armada-380-timer", + "marvell,armada-xp-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 2>, <&coreclk 5>; + clock-names = "nbclk", "fixed"; + }; + + cpurst at 20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x10>; + }; + + pmsu at 22000 { + compatible = "marvell,armada-390-pmsu", + "marvell,armada-380-pmsu"; + reg = <0x22000 0x1000>; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>; + + /* + * This port can be either x4 or x1. When + * configured in x4 by the bootloader, then + * pcie at 4,0 is not available. + */ + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie at 2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie at 3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + /* + * x1 port only available when pcie at 1,0 is + * configured as a x1 port + */ + pcie at 4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + }; + }; +};Signature · 1 line
2.1.0
Thanks!
Maxime
Signature · 10 lines
Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150206/63783d8a/attachment-0001.sig>
PATCH 10/10 Documentation: arm: update supported Marvell EBU processors
In reply to Thomas PetazzoniNow that we support Armada 39x, let's add this family of SoC to the Marvell documentation, and a reference to a link with more details about those processors. Unfortunately, no datasheet is publicly available at this time.
--- Documentation/arm/Marvell/README | 5 +++++ 1 file changed, 5 insertions(+)
Documentation/arm/Marvell/README +5 -0
@@ -96,6 +96,11 @@ EBU Armada family 88F6820 88F6828 + Armada 390/398 Flavors: + 88F6920 + 88F6928 + Product infos: http://www.marvell.com/embedded-processors/armada-39x/ + Armada XP Flavors: MV78230 MV78260
Signature · 1 line
2.1.0