Skip to contentSkip to conversation

configs/qemu: update aarch64 virt

PATCH New Gustavo Zacarias 2 participants 16 messages Apr 15, 2015 – Apr 16, 2015

Subsystems (2)
PowerPC Arm/versatile express platform
lore
Share & tools
lore

Gustavo Zacarias

author
#0 lore raw

PATCH 1/15 configs/qemu: update aarch64 virt

Switch to kernel 4.0.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 .../qemu/aarch64-virt/{linux-3.19.config => linux-4.0.config}  |  0
 board/qemu/aarch64-virt/readme.txt                             |  2 +-
 configs/qemu_aarch64_virt_defconfig                            | 10 +++++-----
 3 files changed, 6 insertions(+), 6 deletions(-)
 rename board/qemu/aarch64-virt/{linux-3.19.config => linux-4.0.config} (100%)
board/qemu/aarch64-virt/linux-4.0.config renamed from board/qemu/aarch64-virt/linux-3.19.config +0 -0
similarity index 100%
rename from board/qemu/aarch64-virt/linux-3.19.config
rename to board/qemu/aarch64-virt/linux-4.0.config
board/qemu/aarch64-virt/readme.txt +1 -1
index c174725..097760c 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_aarch64_virt_defconfig +5 -5
index c99edfa..81b183e 100644
@@ -8,16 +8,16 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/aarch64-virt/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/aarch64-virt/linux-4.0.config"
 BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
 BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
Signature · 1 line
2.0.5
author
#1 lore raw

PATCH 2/15 configs/qemu: update arm versatile

Switch to kernel 4.0.
Remove redudant/pointless kernel options to reduce bloat. Switch from smc9111 to rtl8139 for networking because of issues. Enable evdev support for better x11 testing.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/arm-versatile/linux-3.19.config | 81 ------------------------------
 board/qemu/arm-versatile/linux-4.0.config  | 43 ++++++++++++++++
 board/qemu/arm-versatile/readme.txt        |  4 +-
 configs/qemu_arm_versatile_defconfig       | 10 ++--
 4 files changed, 50 insertions(+), 88 deletions(-)
 delete mode 100644 board/qemu/arm-versatile/linux-3.19.config
 create mode 100644 board/qemu/arm-versatile/linux-4.0.config
board/qemu/arm-versatile/linux-3.19.config deleted +0 -81
deleted file mode 100644
index dd5db53..0000000
@@ -1,81 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_ARCH_VERSATILE=y
-CONFIG_MACH_VERSATILE_AB=y
-CONFIG_PCI=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=1f03 mem=32M"
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_EEPROM_LEGACY=m
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_SYM53C8XX_2=y
-CONFIG_NETDEVICES=y
-CONFIG_SMC91X=y
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_AMBAKMI=y
-CONFIG_LEGACY_PTY_COUNT=16
-CONFIG_SERIAL_8250=m
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_MANY_PORTS=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_8250_RSA=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=m
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-CONFIG_FB_ARMCLCD=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_SOUND=y
-CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-CONFIG_SND_ARMAACI=m
-CONFIG_MMC=y
-CONFIG_MMC_ARMMMCI=m
-CONFIG_EXT4_FS=y
-CONFIG_VFAT_FS=m
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_MINIX_FS=y
-CONFIG_ROMFS_FS=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_FONTS=y
-CONFIG_FONT_ACORN_8x8=y
board/qemu/arm-versatile/linux-4.0.config new file +43 -0

43 lines not on this page · raw message

board/qemu/arm-versatile/readme.txt +2 -2
index cfa30e2..af65d05 100644
@@ -1,8 +1,8 @@
 Run the emulation with:
 
-  qemu-system-arm -M versatilepb -kernel output/images/zImage -drive file=output/images/rootfs.ext2,if=scsi -append "root=/dev/sda console=ttyAMA0,115200" -serial stdio -net nic,model=smc91c111 -net user
+  qemu-system-arm -M versatilepb -kernel output/images/zImage -drive file=output/images/rootfs.ext2,if=scsi -append "root=/dev/sda console=ttyAMA0,115200" -serial stdio -net nic,model=rtl8139 -net user
 
 The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_arm_versatile_defconfig +5 -5
index 272e55b..0c3399e 100644
@@ -10,15 +10,15 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/arm-versatile/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/arm-versatile/linux-4.0.config"
 BR2_LINUX_KERNEL_ZIMAGE=y
Signature · 1 line
2.0.5
author
#2 lore raw

PATCH 3/15 configs/qemu: update arm vexpress

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Switch to DTB (mandatory).
And adjust invocation to use dtb and add a little more RAM for testing.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/arm-vexpress/readme.txt  |  4 ++--
 configs/qemu_arm_vexpress_defconfig | 10 ++++++----
 2 files changed, 8 insertions(+), 6 deletions(-)
board/qemu/arm-vexpress/readme.txt +2 -2
index 937a39b..c8f24be 100644
@@ -1,8 +1,8 @@
 Run the emulation with:
 
-  qemu-system-arm -M vexpress-a9 -kernel output/images/zImage -drive file=output/images/rootfs.ext2,if=sd -append "console=ttyAMA0,115200 root=/dev/mmcblk0" -serial stdio -net nic,model=lan9118 -net user
+  qemu-system-arm -M vexpress-a9 -m 256 -kernel output/images/zImage -dtb output/images/vexpress-v2p-ca9.dtb -drive file=output/images/rootfs.ext2,if=sd -append "console=ttyAMA0,115200 root=/dev/mmcblk0" -serial stdio -net nic,model=lan9118 -net user
 
 The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_arm_vexpress_defconfig +6 -4
index f23da96..7c62ebc 100644
@@ -13,14 +13,16 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.18 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.18.8"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_18=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.18.8"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_DEFCONFIG="vexpress"
 BR2_LINUX_KERNEL_ZIMAGE=y
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="vexpress-v2p-ca9"
Signature · 1 line
2.0.5
author
#3 lore raw

PATCH 4/15 configs/qemu: update microblazebe/el

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Remove redundant/pointless kernel options to reduce bloat.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/microblazebe-mmu/linux-3.19.config | 56 --------------------------
 board/qemu/microblazebe-mmu/linux-4.0.config  | 19 +++++++++
 board/qemu/microblazebe-mmu/readme.txt        |  2 +-
 board/qemu/microblazeel-mmu/linux-3.19.config | 57 ---------------------------
 board/qemu/microblazeel-mmu/linux-4.0.config  | 18 +++++++++
 board/qemu/microblazeel-mmu/readme.txt        |  2 +-
 configs/qemu_microblazebe_mmu_defconfig       | 10 ++---
 configs/qemu_microblazeel_mmu_defconfig       | 10 ++---
 8 files changed, 49 insertions(+), 125 deletions(-)
 delete mode 100644 board/qemu/microblazebe-mmu/linux-3.19.config
 create mode 100644 board/qemu/microblazebe-mmu/linux-4.0.config
 delete mode 100644 board/qemu/microblazeel-mmu/linux-3.19.config
 create mode 100644 board/qemu/microblazeel-mmu/linux-4.0.config
board/qemu/microblazebe-mmu/linux-3.19.config deleted +0 -56
deleted file mode 100644
index fc25c9d..0000000
@@ -1,56 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE="rootfs.cpio"
-CONFIG_EXPERT=y
-CONFIG_KALLSYMS_ALL=y
-# CONFIG_BASE_FULL is not set
-# CONFIG_FUTEX is not set
-# CONFIG_EPOLL is not set
-# CONFIG_SIGNALFD is not set
-# CONFIG_SHMEM is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_OPT_LIB_ASM=y
-CONFIG_XILINX_MICROBLAZE0_FAMILY="spartan3adsp"
-CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
-CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR=1
-CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
-CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=1
-CONFIG_HZ_100=y
-CONFIG_MMU=y
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE_FORCE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_XILINX_EMACLITE=y
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_UARTLITE=y
-CONFIG_SERIAL_UARTLITE_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_DNOTIFY is not set
-CONFIG_NFS_FS=y
-CONFIG_CIFS=y
-CONFIG_CIFS_STATS=y
-CONFIG_CIFS_STATS2=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_SLAB=y
-CONFIG_DETECT_HUNG_TASK=y
-CONFIG_DEBUG_SPINLOCK=y
-CONFIG_EARLY_PRINTK=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
board/qemu/microblazebe-mmu/linux-4.0.config new file +19 -0
new file mode 100644
index 0000000..6b4ff22
@@ -0,0 +1,19 @@
+CONFIG_SYSVIPC=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_OPT_LIB_ASM=y
+CONFIG_XILINX_MICROBLAZE0_FAMILY="spartan3adsp"
+CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
+CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=1
+CONFIG_MMU=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_NETDEVICES=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+# CONFIG_VGA_CONSOLE is not set
board/qemu/microblazebe-mmu/readme.txt +1 -1
index c6375cc..9f93ab5 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
board/qemu/microblazeel-mmu/linux-3.19.config deleted +0 -57

57 lines not on this page · raw message

board/qemu/microblazeel-mmu/linux-4.0.config new file +18 -0
new file mode 100644
index 0000000..c7d6b30
@@ -0,0 +1,18 @@
+CONFIG_SYSVIPC=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_XILINX_MICROBLAZE0_FAMILY="spartan3adsp"
+CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR=1
+CONFIG_XILINX_MICROBLAZE0_USE_BARREL=1
+CONFIG_XILINX_MICROBLAZE0_USE_HW_MUL=1
+CONFIG_MMU=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_NETDEVICES=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+# CONFIG_VGA_CONSOLE is not set
board/qemu/microblazeel-mmu/readme.txt +1 -1
index 3a5d55a..230527d 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_microblazebe_mmu_defconfig +5 -5
index 8fb077b..098688b 100644
@@ -9,16 +9,16 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/microblazebe-mmu/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/microblazebe-mmu/linux-4.0.config"
 BR2_LINUX_KERNEL_LINUX_BIN=y
 BR2_LINUX_KERNEL_PATCH="board/qemu/microblazebe-mmu/xilinx-xemaclite.patch"
configs/qemu_microblazeel_mmu_defconfig +5 -5
index 80f8207..021018c 100644
@@ -9,16 +9,16 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyUL0"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/microblazeel-mmu/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/microblazeel-mmu/linux-4.0.config"
 BR2_LINUX_KERNEL_LINUX_BIN=y
 BR2_LINUX_KERNEL_PATCH="board/qemu/microblazeel-mmu/xilinx-xemaclite.patch"
Signature · 1 line
2.0.5
author
#4 lore raw

PATCH 5/15 configs/qemu: update ppc64 pseries

In reply to Gustavo Zacarias

Switch to kernel 4.0.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/ppc64-pseries/readme.txt  | 2 +-
 configs/qemu_ppc64_pseries_defconfig | 8 ++++----
 2 files changed, 5 insertions(+), 5 deletions(-)
board/qemu/ppc64-pseries/readme.txt +1 -1
index 6d5157e..718da6f 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_ppc64_pseries_defconfig +4 -4
index d73e67f..5fe5e6a 100644
@@ -10,14 +10,14 @@ BR2_TARGET_GENERIC_GETTY_PORT="hvc0"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_DEFCONFIG="pseries"
 BR2_LINUX_KERNEL_VMLINUX=y
Signature · 1 line
2.0.5
author
#5 lore raw

PATCH 6/15 configs/qemu: update sparc ss10

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Switch kernel config to ext4, simplify to reduce bloat. Adjust invocation to keep the framebuffer window for graphics testing.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/sparc-ss10/linux-3.19.config | 95 ---------------------------------
 board/qemu/sparc-ss10/linux-4.0.config  | 31 +++++++++++
 board/qemu/sparc-ss10/readme.txt        |  4 +-
 configs/qemu_sparc_ss10_defconfig       | 10 ++--
 4 files changed, 38 insertions(+), 102 deletions(-)
 delete mode 100644 board/qemu/sparc-ss10/linux-3.19.config
 create mode 100644 board/qemu/sparc-ss10/linux-4.0.config
board/qemu/sparc-ss10/linux-3.19.config deleted +0 -95
deleted file mode 100644
index 0e7e500..0000000
@@ -1,95 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PCI=y
-CONFIG_SUN_OPENPROMFS=m
-CONFIG_BINFMT_MISC=m
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_USER=m
-CONFIG_NET_KEY=m
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_INET_AH=y
-CONFIG_INET_ESP=y
-CONFIG_INET_IPCOMP=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET6_AH=m
-CONFIG_INET6_ESP=m
-CONFIG_INET6_IPCOMP=m
-CONFIG_IPV6_TUNNEL=m
-CONFIG_NET_PKTGEN=m
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_BLK_DEV_LOOP=m
-CONFIG_BLK_DEV_CRYPTOLOOP=m
-CONFIG_BLK_DEV_RAM=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=m
-CONFIG_SCSI_QLOGICPTI=m
-CONFIG_SCSI_SUNESP=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=m
-CONFIG_SUNLANCE=y
-CONFIG_HAPPYMEAL=m
-CONFIG_SUNBMAC=m
-CONFIG_SUNQE=m
-# CONFIG_WLAN is not set
-CONFIG_INPUT_JOYDEV=m
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-CONFIG_KEYBOARD_ATKBD=m
-CONFIG_KEYBOARD_SUNKBD=m
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_SERIO=m
-CONFIG_SERIAL_SUNZILOG=y
-CONFIG_SERIAL_SUNZILOG_CONSOLE=y
-CONFIG_SERIAL_SUNSU=y
-CONFIG_SERIAL_SUNSU_CONSOLE=y
-CONFIG_SPI=y
-CONFIG_SPI_XILINX=m
-CONFIG_SUN_OPENPROMIO=m
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT2_FS_SECURITY=y
-CONFIG_AUTOFS4_FS=m
-CONFIG_ISO9660_FS=m
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_ROMFS_FS=m
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_SCHED_DEBUG is not set
-CONFIG_KGDB=y
-CONFIG_KGDB_TESTS=y
-CONFIG_CRYPTO_NULL=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_MD4=y
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_SHA256=m
-CONFIG_CRYPTO_SHA512=m
-CONFIG_CRYPTO_ARC4=m
-CONFIG_CRYPTO_BLOWFISH=m
-CONFIG_CRYPTO_CAST5=m
-CONFIG_CRYPTO_CAST6=m
-CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TWOFISH=m
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-CONFIG_LIBCRC32C=m
board/qemu/sparc-ss10/linux-4.0.config new file +31 -0
new file mode 100644
index 0000000..cb8d01d
@@ -0,0 +1,31 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PCI=y
+CONFIG_SUN_OPENPROMFS=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_WIRELESS is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_SUNESP=y
+CONFIG_NETDEVICES=y
+CONFIG_SUNLANCE=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_SUNKBD=y
+CONFIG_MOUSE_SERIAL=y
+CONFIG_SERIAL_SUNZILOG=y
+CONFIG_SERIAL_SUNZILOG_CONSOLE=y
+CONFIG_SERIAL_SUNSU=y
+CONFIG_SERIAL_SUNSU_CONSOLE=y
+CONFIG_SUN_OPENPROMIO=m
+CONFIG_EXT4_FS=y
+CONFIG_ISO9660_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/sparc-ss10/readme.txt +2 -2
index 88f98d5..1972a11 100644
@@ -1,7 +1,7 @@
 Run the emulation with:
 
-  qemu-system-sparc -M SS-10 -kernel output/images/zImage -drive file=output/images/rootfs.ext2 -append "root=/dev/sda console=ttyS0,115200" -serial stdio -net nic,model=lance -net user -display none
+  qemu-system-sparc -M SS-10 -kernel output/images/zImage -drive file=output/images/rootfs.ext2 -append "root=/dev/sda console=ttyS0,115200" -serial stdio -net nic,model=lance -net user
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_sparc_ss10_defconfig +5 -5
index 73195fa..1fff720 100644
@@ -8,15 +8,15 @@ BR2_GLOBAL_PATCH_DIR="board/qemu/sparc-ss10"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Linux kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/sparc-ss10/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/sparc-ss10/linux-4.0.config"
 BR2_LINUX_KERNEL_ZIMAGE=y
Signature · 1 line
2.0.5
author
#6 lore raw

PATCH 7/15 configs/qemu: update mips malta configurations

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Simplify kernel config to reduce bloat.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/mips-malta/linux-3.19.config     | 60 ----------------------------
 board/qemu/mips-malta/linux-4.0.config      | 28 +++++++++++++
 board/qemu/mips-malta/readme.txt            |  2 +-
 board/qemu/mips64-malta/linux-3.19.config   | 60 ----------------------------
 board/qemu/mips64-malta/linux-4.0.config    | 32 +++++++++++++++
 board/qemu/mips64-malta/readme.txt          |  2 +-
 board/qemu/mips64el-malta/linux-3.19.config | 61 -----------------------------
 board/qemu/mips64el-malta/linux-4.0.config  | 33 ++++++++++++++++
 board/qemu/mips64el-malta/readme.txt        |  2 +-
 board/qemu/mipsel-malta/linux-3.19.config   | 61 -----------------------------
 board/qemu/mipsel-malta/linux-4.0.config    | 29 ++++++++++++++
 board/qemu/mipsel-malta/readme.txt          |  2 +-
 configs/qemu_mips64_malta_defconfig         | 10 ++---
 configs/qemu_mips64el_malta_defconfig       | 10 ++---
 configs/qemu_mips_malta_defconfig           | 10 ++---
 configs/qemu_mipsel_malta_defconfig         | 10 ++---
 16 files changed, 146 insertions(+), 266 deletions(-)
 delete mode 100644 board/qemu/mips-malta/linux-3.19.config
 create mode 100644 board/qemu/mips-malta/linux-4.0.config
 delete mode 100644 board/qemu/mips64-malta/linux-3.19.config
 create mode 100644 board/qemu/mips64-malta/linux-4.0.config
 delete mode 100644 board/qemu/mips64el-malta/linux-3.19.config
 create mode 100644 board/qemu/mips64el-malta/linux-4.0.config
 delete mode 100644 board/qemu/mipsel-malta/linux-3.19.config
 create mode 100644 board/qemu/mipsel-malta/linux-4.0.config
board/qemu/mips-malta/linux-3.19.config deleted +0 -60
deleted file mode 100644
index 4716bb6..0000000
@@ -1,60 +0,0 @@
-CONFIG_MIPS_MALTA=y
-CONFIG_CPU_MIPS32_R2=y
-CONFIG_MIPS_MT_SMP=y
-CONFIG_NR_CPUS=2
-CONFIG_HZ_100=y
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_LOG_BUF_SHIFT=15
-CONFIG_NAMESPACES=y
-CONFIG_RELAY=y
-CONFIG_EMBEDDED=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PCI=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_IDE_GENERIC=y
-CONFIG_BLK_DEV_GENERIC=y
-CONFIG_BLK_DEV_PIIX=y
-CONFIG_NETDEVICES=y
-CONFIG_PCNET32=y
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO_I8042 is not set
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-CONFIG_FB_CIRRUS=y
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_USB_SUPPORT is not set
-CONFIG_EXT4_FS=y
-CONFIG_QUOTA=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
board/qemu/mips-malta/linux-4.0.config new file +28 -0
new file mode 100644
index 0000000..60fcd70
@@ -0,0 +1,28 @@
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_MIPS_MT_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PCI=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDECD=y
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_GENERIC=y
+CONFIG_BLK_DEV_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_PCNET32=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/mips-malta/readme.txt +1 -1
index 7dac3cb..2c96059 100644
@@ -6,4 +6,4 @@ The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer. No keyboard support has been
 enabled.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
board/qemu/mips64-malta/linux-3.19.config deleted +0 -60

60 lines not on this page · raw message

board/qemu/mips64-malta/linux-4.0.config new file +32 -0
new file mode 100644
index 0000000..9b5d4e6
@@ -0,0 +1,32 @@
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_MIPS64_R1=y
+CONFIG_64BIT=y
+CONFIG_MIPS_MT_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PCI=y
+CONFIG_MIPS32_COMPAT=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDECD=y
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_GENERIC=y
+CONFIG_BLK_DEV_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_PCNET32=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/mips64-malta/readme.txt +1 -1
index 11fba34..80c9310 100644
@@ -5,4 +5,4 @@ Run the emulation with:
 The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
board/qemu/mips64el-malta/linux-3.19.config deleted +0 -61

61 lines not on this page · raw message

board/qemu/mips64el-malta/linux-4.0.config new file +33 -0
new file mode 100644
index 0000000..8877a2e
@@ -0,0 +1,33 @@
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS64_R1=y
+CONFIG_64BIT=y
+CONFIG_MIPS_MT_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PCI=y
+CONFIG_MIPS32_COMPAT=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDECD=y
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_GENERIC=y
+CONFIG_BLK_DEV_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_PCNET32=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/mips64el-malta/readme.txt +1 -1
index 8ad80c4..82ab883 100644
@@ -5,4 +5,4 @@ Run the emulation with:
 The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
board/qemu/mipsel-malta/linux-3.19.config deleted +0 -61

61 lines not on this page · raw message

board/qemu/mipsel-malta/linux-4.0.config new file +29 -0
new file mode 100644
index 0000000..b9a743f
@@ -0,0 +1,29 @@
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_MIPS_MT_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PCI=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDECD=y
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_GENERIC=y
+CONFIG_BLK_DEV_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_PCNET32=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/mipsel-malta/readme.txt +1 -1
index 27d3153..a77eb88 100644
@@ -6,4 +6,4 @@ The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer. No keyboard support has been
 enabled.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_mips64_malta_defconfig +5 -5
index 8bce340..35761ff 100644
@@ -6,17 +6,17 @@ BR2_MIPS_NABI64=y
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips64-malta/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips64-malta/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 
 # Serial port config
configs/qemu_mips64el_malta_defconfig +5 -5
index 8999e6c..923cccd 100644
@@ -6,17 +6,17 @@ BR2_MIPS_NABI64=y
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips64el-malta/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips64el-malta/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 
 # Serial port config
configs/qemu_mips_malta_defconfig +5 -5
index 4ed02c0..d09a16b 100644
@@ -6,17 +6,17 @@ BR2_mips_32r2=y
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips-malta/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mips-malta/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 
 # Serial port config
configs/qemu_mipsel_malta_defconfig +5 -5
index 012eefe..f345d71 100644
@@ -6,17 +6,17 @@ BR2_mips_32r2=y
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mipsel-malta/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/mipsel-malta/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 
 # Serial port config
Signature · 1 line
2.0.5
author
#7 lore raw

PATCH 8/15 configs/qemu: update sh4 r2d

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Simplify kernel config to reduce bloat.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/sh4-r2d/linux-3.19.config | 71 ------------------------------------
 board/qemu/sh4-r2d/linux-4.0.config  | 38 +++++++++++++++++++
 board/qemu/sh4-r2d/readme.txt        |  2 +-
 configs/qemu_sh4_r2d_defconfig       | 10 ++---
 4 files changed, 44 insertions(+), 77 deletions(-)
 delete mode 100644 board/qemu/sh4-r2d/linux-3.19.config
 create mode 100644 board/qemu/sh4-r2d/linux-4.0.config
board/qemu/sh4-r2d/linux-3.19.config deleted +0 -71
deleted file mode 100644
index 5a98a69..0000000
@@ -1,71 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SLAB=y
-CONFIG_PROFILING=y
-CONFIG_OPROFILE=y
-CONFIG_MODULES=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_CPU_SUBTYPE_SH7751R=y
-CONFIG_MEMORY_START=0x0c000000
-CONFIG_FLATMEM_MANUAL=y
-CONFIG_SH_RTS7751R2D=y
-CONFIG_RTS7751R2D_PLUS=y
-CONFIG_HEARTBEAT=y
-CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_FW_LOADER=m
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_ATA=y
-CONFIG_PATA_PLATFORM=y
-CONFIG_NETDEVICES=y
-CONFIG_8139CP=y
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_SPI=y
-CONFIG_SPI_SH_SCI=y
-CONFIG_MFD_SM501=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=m
-CONFIG_FB_SH_MOBILE_HDMI=m
-CONFIG_FB_SM501=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_SND_YMFPCI=m
-CONFIG_SOUND_PRIME=m
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_R9701=y
-CONFIG_EXT4_FS=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_MINIX_FS=y
-CONFIG_NLS_CODEPAGE_932=y
-CONFIG_DEBUG_FS=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_T10DIF=y
board/qemu/sh4-r2d/linux-4.0.config new file +38 -0
new file mode 100644
index 0000000..a3d6544
@@ -0,0 +1,38 @@
+CONFIG_SYSVIPC=y
+CONFIG_MODULES=y
+CONFIG_CPU_SUBTYPE_SH7751R=y
+CONFIG_MEMORY_START=0x0c000000
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_SH_RTS7751R2D=y
+CONFIG_RTS7751R2D_PLUS=y
+CONFIG_HEARTBEAT=y
+CONFIG_PCI=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_PATA_PLATFORM=y
+CONFIG_NETDEVICES=y
+CONFIG_8139CP=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+CONFIG_SPI=y
+CONFIG_SPI_SH_SCI=y
+CONFIG_MFD_SM501=y
+CONFIG_FB=y
+CONFIG_FB_SH_MOBILE_LCDC=y
+CONFIG_FB_SH_MOBILE_HDMI=y
+CONFIG_FB_SM501=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND_YMFPCI=y
+CONFIG_SOUND_PRIME=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_R9701=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/sh4-r2d/readme.txt +1 -1
index c256f0b..b7476b9 100644
@@ -5,4 +5,4 @@ Run the emulation with:
 The login prompt will appear in the terminal that started Qemu.
 The graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_sh4_r2d_defconfig +5 -5
index 88bf914..928a82d 100644
@@ -14,15 +14,15 @@ BR2_TARGET_ROOTFS_EXT2=y
 # doesn't use floating point operations.
 BR2_EXTRA_GCC_CONFIG_OPTIONS="--with-multilib-list=m4,m4-nofpu"
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Linux kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/sh4-r2d/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/sh4-r2d/linux-4.0.config"
 BR2_LINUX_KERNEL_ZIMAGE=y
Signature · 1 line
2.0.5
author
#8 lore raw

PATCH 9/15 configs/qemu: update xtensa lx60

In reply to Gustavo Zacarias

Switch to kernel 4.0.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/xtensa-lx60/{linux-3.19.config => linux-4.0.config} |  0
 board/qemu/xtensa-lx60/readme.txt                              |  2 +-
 configs/qemu_xtensa_lx60_defconfig                             | 10 +++++-----
 3 files changed, 6 insertions(+), 6 deletions(-)
 rename board/qemu/xtensa-lx60/{linux-3.19.config => linux-4.0.config} (100%)
board/qemu/xtensa-lx60/linux-4.0.config renamed from board/qemu/xtensa-lx60/linux-3.19.config +0 -0
similarity index 100%
rename from board/qemu/xtensa-lx60/linux-3.19.config
rename to board/qemu/xtensa-lx60/linux-4.0.config
board/qemu/xtensa-lx60/readme.txt +1 -1
index 0f138bc..2dad34a 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_xtensa_lx60_defconfig +5 -5
index 4eb10fb..b3ac6b3 100644
@@ -14,17 +14,17 @@ BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/xtensa-lx60/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/xtensa-lx60/linux-4.0.config"
 BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
 BR2_LINUX_KERNEL_IMAGE_NAME="Image.elf"
 BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="zImage"
Signature · 1 line
2.0.5
author
#9 lore raw

PATCH 10/15 configs/qemu: update ppc virtex ml507

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Use a custom kernel config to avoid the caveat of a huge debug-enabled one.
And also reduce defconfig options to avoid bloat.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/ppc-virtex-ml507/linux-4.0.config | 36 ++++++++++++++++++++++++++++
 board/qemu/ppc-virtex-ml507/readme.txt       |  2 +-
 configs/qemu_ppc_virtex_ml507_defconfig      | 11 +++++----
 3 files changed, 43 insertions(+), 6 deletions(-)
 create mode 100644 board/qemu/ppc-virtex-ml507/linux-4.0.config
board/qemu/ppc-virtex-ml507/linux-4.0.config new file +36 -0
new file mode 100644
index 0000000..ed4eb79
@@ -0,0 +1,36 @@
+CONFIG_44x=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_EBONY is not set
+CONFIG_XILINX_VIRTEX440_GENERIC_BOARD=y
+CONFIG_MATH_EMULATION=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_XILINX_SYSACE=y
+CONFIG_NETDEVICES=y
+CONFIG_SERIO_XILINX_XPS_PS2=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_XILINX_HWICAP=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_FB=y
+CONFIG_FB_XILINX=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_EXT4_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
board/qemu/ppc-virtex-ml507/readme.txt +1 -1
index f8bf150..0cf1f9d 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the terminal that started Qemu.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_ppc_virtex_ml507_defconfig +6 -5
index a5b97db..fd53483 100644
@@ -6,10 +6,10 @@ BR2_powerpc_440=y
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Use soft float
 BR2_SOFT_FLOAT=y

@@ -17,8 +17,9 @@ BR2_SOFT_FLOAT=y
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
-BR2_LINUX_KERNEL_DEFCONFIG="44x/virtex5"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
+BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/ppc-virtex-ml507/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="virtex440-ml507"
Signature · 1 line
2.0.5
author
#10 lore raw

PATCH 11/15 configs/qemu: update x86

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/x86/linux-3.19.config | 63 ----------------------------------------
 board/qemu/x86/linux-4.0.config  | 20 +++++++++++++
 board/qemu/x86/readme.txt        |  2 +-
 configs/qemu_x86_defconfig       | 10 +++----
 4 files changed, 26 insertions(+), 69 deletions(-)
 delete mode 100644 board/qemu/x86/linux-3.19.config
 create mode 100644 board/qemu/x86/linux-4.0.config
board/qemu/x86/linux-3.19.config deleted +0 -63
deleted file mode 100644
index 602a9bb..0000000
@@ -1,63 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-# CONFIG_COMPAT_BRK is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-# CONFIG_X86_EXTENDED_PLATFORM is not set
-# CONFIG_SCHED_OMIT_FRAME_POINTER is not set
-# CONFIG_MTRR_SANITIZER is not set
-# CONFIG_SECCOMP is not set
-# CONFIG_RELOCATABLE is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FIRMWARE_IN_KERNEL is not set
-# CONFIG_BLK_DEV is not set
-CONFIG_BLK_DEV_SD=y
-CONFIG_ATA=y
-CONFIG_ATA_PIIX=y
-CONFIG_NETDEVICES=y
-CONFIG_NE2K_PCI=y
-CONFIG_8139CP=y
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_HDA_INTEL=y
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_X86_PLATFORM_DEVICES is not set
-# CONFIG_DMIID is not set
-CONFIG_EXT4_FS=y
-# CONFIG_DNOTIFY is not set
-# CONFIG_INOTIFY_USER is not set
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_FRAME_POINTER is not set
-# CONFIG_X86_VERBOSE_BOOTUP is not set
-# CONFIG_VIRTUALIZATION is not set
board/qemu/x86/linux-4.0.config new file +20 -0
new file mode 100644
index 0000000..ce19f81
@@ -0,0 +1,20 @@
+CONFIG_SYSVIPC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_NE2K_PCI=y
+CONFIG_8139CP=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_HDA_INTEL=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/x86/readme.txt +1 -1
index 1d4e123..85d5c60 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the graphical window.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_x86_defconfig +5 -5
index f0831b0..0892d39 100644
@@ -10,14 +10,14 @@ BR2_TARGET_GENERIC_GETTY_PORT="tty1"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/x86/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/x86/linux-4.0.config"
Signature · 1 line
2.0.5
author
#11 lore raw

PATCH 12/15 configs/qemu: update x86_64

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/x86_64/linux-3.19.config | 63 -------------------------------------
 board/qemu/x86_64/linux-4.0.config  | 20 ++++++++++++
 board/qemu/x86_64/readme.txt        |  2 +-
 configs/qemu_x86_64_defconfig       | 10 +++---
 4 files changed, 26 insertions(+), 69 deletions(-)
 delete mode 100644 board/qemu/x86_64/linux-3.19.config
 create mode 100644 board/qemu/x86_64/linux-4.0.config
board/qemu/x86_64/linux-3.19.config deleted +0 -63
deleted file mode 100644
index 602a9bb..0000000
@@ -1,63 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-# CONFIG_COMPAT_BRK is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-# CONFIG_X86_EXTENDED_PLATFORM is not set
-# CONFIG_SCHED_OMIT_FRAME_POINTER is not set
-# CONFIG_MTRR_SANITIZER is not set
-# CONFIG_SECCOMP is not set
-# CONFIG_RELOCATABLE is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FIRMWARE_IN_KERNEL is not set
-# CONFIG_BLK_DEV is not set
-CONFIG_BLK_DEV_SD=y
-CONFIG_ATA=y
-CONFIG_ATA_PIIX=y
-CONFIG_NETDEVICES=y
-CONFIG_NE2K_PCI=y
-CONFIG_8139CP=y
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_HDA_INTEL=y
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_X86_PLATFORM_DEVICES is not set
-# CONFIG_DMIID is not set
-CONFIG_EXT4_FS=y
-# CONFIG_DNOTIFY is not set
-# CONFIG_INOTIFY_USER is not set
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_FRAME_POINTER is not set
-# CONFIG_X86_VERBOSE_BOOTUP is not set
-# CONFIG_VIRTUALIZATION is not set
board/qemu/x86_64/linux-4.0.config new file +20 -0
new file mode 100644
index 0000000..ce19f81
@@ -0,0 +1,20 @@
+CONFIG_SYSVIPC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_NETDEVICES=y
+CONFIG_NE2K_PCI=y
+CONFIG_8139CP=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_HDA_INTEL=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
board/qemu/x86_64/readme.txt +1 -1
index 626ec2f..d397a79 100644
@@ -4,4 +4,4 @@ Run the emulation with:
 
 The login prompt will appear in the graphical window.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_x86_64_defconfig +5 -5
index 8cb777a..01ffcc0 100644
@@ -9,14 +9,14 @@ BR2_TARGET_GENERIC_GETTY_PORT="tty1"
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/x86_64/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/x86_64/linux-4.0.config"
Signature · 1 line
2.0.5
author
#12 lore raw

PATCH 13/15 configs/qemu: update nuri to latest 3.10.x kernel

In reply to Gustavo Zacarias
Signed-off-by Gustavo Zacarias <[email protected]>
---
 board/qemu/arm-nuri/readme.txt  | 3 ++-
 configs/qemu_arm_nuri_defconfig | 4 ++--
 2 files changed, 4 insertions(+), 3 deletions(-)
board/qemu/arm-nuri/readme.txt +2 -1
index 6fe1ac0..d7a6428 100644
@@ -6,5 +6,6 @@ The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
 Startup time is slow because of the SMP CPU emulation so be patient.
+This emulation is known to be flaky.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_arm_nuri_defconfig +2 -2
index bf70df0..7a270ed 100644
@@ -16,12 +16,12 @@ BR2_TARGET_ROOTFS_INITRAMFS=y
 # Lock to 3.10 headers to avoid breaking with newer kernels
 # Stuck at 3.10.x because there's no Nuri DTS
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.10.70"
+BR2_DEFAULT_KERNEL_VERSION="3.10.74"
 BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_10=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.10.70"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.10.74"
 BR2_LINUX_KERNEL_DEFCONFIG="exynos4"
 BR2_LINUX_KERNEL_ZIMAGE=y
Signature · 1 line
2.0.5
author
#13 lore raw

PATCH 14/15 configs/qemu: update ppc g3beige

In reply to Gustavo Zacarias

Switch to kernel 4.0.
Simplify kernel config to reduce bloat.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 .../{linux-3.19.config => linux-4.0.config}         | 21 ---------------------
 board/qemu/ppc-g3beige/readme.txt                   |  2 +-
 configs/qemu_ppc_g3beige_defconfig                  | 10 +++++-----
 3 files changed, 6 insertions(+), 27 deletions(-)
 rename board/qemu/ppc-g3beige/{linux-3.19.config => linux-4.0.config} (54%)
board/qemu/ppc-g3beige/linux-4.0.config renamed from board/qemu/ppc-g3beige/linux-3.19.config +0 -21
similarity index 54%
rename from board/qemu/ppc-g3beige/linux-3.19.config
rename to board/qemu/ppc-g3beige/linux-4.0.config
index 26be1c5..7994553 100644
@@ -1,19 +1,11 @@
 CONFIG_ALTIVEC=y
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_PPC601_SYNC_FIX=y
 CONFIG_HIGHMEM=y
-CONFIG_PCCARD=y
 CONFIG_YENTA=y
-CONFIG_ADVANCED_OPTIONS=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
-CONFIG_CONNECTOR=y
-CONFIG_BLK_DEV_LOOP=y
 CONFIG_IDE=y
 CONFIG_BLK_DEV_IDECD=y
 CONFIG_BLK_DEV_CMD64X=y

@@ -23,24 +15,11 @@ CONFIG_ADB_CUDA=y
 CONFIG_ADB_PMU=y
 CONFIG_NETDEVICES=y
 CONFIG_PCNET32=y
-CONFIG_MACE=y
-CONFIG_BMAC=y
-CONFIG_NE2K_PCI=y
 CONFIG_8139CP=y
-CONFIG_8139TOO=y
-CONFIG_HAPPYMEAL=y
-CONFIG_SUNGEM=y
-CONFIG_CASSINI=y
 CONFIG_SERIAL_PMACZILOG=y
 CONFIG_SERIAL_PMACZILOG_TTYS=y
 CONFIG_SERIAL_PMACZILOG_CONSOLE=y
-CONFIG_SSB=y
-CONFIG_SSB_PCMCIAHOST=y
-CONFIG_SSB_DRIVER_PCICORE=y
 CONFIG_EXT4_FS=y
-CONFIG_PROC_KCORE=y
 CONFIG_TMPFS=y
 CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_SQUASHFS=y
-CONFIG_LIBCRC32C=y
 CONFIG_BOOTX_TEXT=y
board/qemu/ppc-g3beige/readme.txt +1 -1
index 65cb261..cd358b3 100644
@@ -5,4 +5,4 @@ Run the emulation with:
 The login prompt will appear in the terminal that started Qemu. The
 graphical window is the framebuffer.
 
-Tested with QEMU 2.2.0
+Tested with QEMU 2.2.1
configs/qemu_ppc_g3beige_defconfig +5 -5
index 285093c..3e3438c 100644
@@ -6,17 +6,17 @@ BR2_powerpc_750=y
 BR2_TARGET_ROOTFS_EXT2=y
 # BR2_TARGET_ROOTFS_TAR is not set
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/ppc-g3beige/linux-3.19.config"
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/ppc-g3beige/linux-4.0.config"
 BR2_LINUX_KERNEL_VMLINUX=y
 
 # Serial port config
Signature · 1 line
2.0.5
author
#14 lore raw

PATCH 15/15 configs/qemu: update ppc mpc8544ds

In reply to Gustavo Zacarias

Switch to kernel 4.0.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 configs/qemu_ppc_mpc8544ds_defconfig | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
configs/qemu_ppc_mpc8544ds_defconfig +4 -4
index 14faac3..52bc320 100644
@@ -6,15 +6,15 @@ BR2_powerpc_8548=y
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ROOTFS_INITRAMFS=y
 
-# Lock to 3.19 headers to avoid breaking with newer kernels
+# Lock to 4.0 headers to avoid breaking with newer kernels
 BR2_KERNEL_HEADERS_VERSION=y
-BR2_DEFAULT_KERNEL_VERSION="3.19"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="3.19"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.0"
 BR2_LINUX_KERNEL_DEFCONFIG="mpc85xx"
 BR2_LINUX_KERNEL_VMLINUX=y
Signature · 1 line
2.0.5
#15 lore raw

PATCH 1/15 configs/qemu: update aarch64 virt

In reply to Gustavo Zacarias

Dear Gustavo Zacarias,

Quoted 9 lines · Gustavo Zacarias

Switch to kernel 4.0.

Signed-off-by Gustavo Zacarias <[email protected]>
---
 .../qemu/aarch64-virt/{linux-3.19.config => linux-4.0.config}  |  0
 board/qemu/aarch64-virt/readme.txt                             |  2 +-
 configs/qemu_aarch64_virt_defconfig                            | 10 +++++-----
 3 files changed, 6 insertions(+), 6 deletions(-)
 rename board/qemu/aarch64-virt/{linux-3.19.config => linux-4.0.config} (100%)

Series applied, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com