hummingboard: Remove mx6solo specific support

index 7c383cb..b97f72b 100644
@@ -542,10 +542,6 @@ config TARGET_GW_VENTANA
 	select CPU_V7
 	select SUPPORT_SPL
 
-config TARGET_HUMMINGBOARD
-	bool "Support hummingboard"
-	select CPU_V7
-
 config TARGET_KOSAGI_NOVENA
 	bool "Support Kosagi Novena"
 	select CPU_V7

@@ -862,7 +858,6 @@ source "board/siemens/pxm2/Kconfig"
 source "board/siemens/rut/Kconfig"
 source "board/silica/pengwyn/Kconfig"
 source "board/solidrun/mx6cuboxi/Kconfig"
-source "board/solidrun/hummingboard/Kconfig"
 source "board/spear/spear300/Kconfig"
 source "board/spear/spear310/Kconfig"
 source "board/spear/spear320/Kconfig"

deleted file mode 100644
index 36b7904..0000000
@@ -1,15 +0,0 @@
-if TARGET_HUMMINGBOARD
-
-config SYS_BOARD
-	default "hummingboard"
-
-config SYS_VENDOR
-	default "solidrun"
-
-config SYS_SOC
-	default "mx6"
-
-config SYS_CONFIG_NAME
-	default "hummingboard"
-
-endif

deleted file mode 100644
index c0c062a..0000000
@@ -1,6 +0,0 @@
-HUMMINGBOARD BOARD
-M:	Jon Nettleton <[email protected]>
-S:	Maintained
-F:	board/solidrun/hummingboard/
-F:	include/configs/hummingboard.h
-F:	configs/hummingboard_solo_defconfig

deleted file mode 100644
index 042a2f0..0000000
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2013 Freescale Semiconductor, Inc.
-# Copyright (C) 2013, Boundary Devices <[email protected]>
-# Copyright (C) 2013, Jon Nettleton <[email protected]>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y  := hummingboard.o

deleted file mode 100644
index cfd62d4..0000000
@@ -1,40 +0,0 @@
-U-Boot for SolidRun Hummingboard
---------------------------------
-
-This file contains information for the port of U-Boot to the Hummingboard.
-
-For more details about Hummingboard, please refer to:
-http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
-
-(Carrier-One was the previous name of Hummingboard).
-
-Building U-boot for Hummingboard
---------------------------------
-
-To build U-Boot for the Hummingboard Solo version:
-
-$ make hummingboard_solo_config
-$ make
-
-Flashing U-boot into the SD card
---------------------------------
-
-- After the 'make' command completes, the generated 'u-boot.imx' binary must be
-flashed into the SD card:
-
-$ sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=1k seek=1; sync
-
-(Note - the SD card node may vary, so adjust this as needed).
-
-Also, a more detailed explanation on how to format the SD card is available
-at doc/README.imximage.
-
-- Insert the micro SD card into the slot located in the bottom of the board
-
-- Connect a 3.3V USB to serial converter cable to the host PC. The MX6 UART
-signals are available in the 26 pin connector as shown at:
-http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
-(Check for "26 pin header layout").
-
-- Power up the board via USB cable (CON201) and U-boot messages will appear in
-the serial console.

deleted file mode 100644
index 28dd750..0000000
@@ -1,25 +0,0 @@
-/*
- * Copyright (C) 2013 Boundary Devices
- * Copyright (C) 2013 Jon Nettleton <[email protected]>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM      sd
-
-#define __ASSEMBLY__
-#include <config.h>
-#include "asm/arch/mx6-ddr.h"
-#include "asm/arch/iomux.h"
-#include "asm/arch/crm_regs.h"
-
-#include "../mx6-microsom/ddr-800mhz-32bit-setup.cfg"
-#include "../mx6-microsom/800mhz_2x128mx16.cfg"
-#include "../mx6-microsom/clocks.cfg"

deleted file mode 100644
index 600fa00..0000000
@@ -1,3 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/solidrun/hummingboard/solo.cfg,MX6S,DDR_MB=512"
-CONFIG_ARM=y
-CONFIG_TARGET_HUMMINGBOARD=y

index 3050c48..b417ff0 100644
@@ -1,7 +1,7 @@
-How to use U-boot on Solid-run mx6 hummingboard
------------------------------------------------
+How to use U-boot on Solid-run mx6 Hummingboard and Cubox-i
+-----------------------------------------------------------
 
-- Build U-boot for hummingboard:
+- Build U-boot for Hummingboard/Cubox-i:
 
 $ make mrproper
 $ make mx6cuboxi_defconfig

@@ -17,5 +17,5 @@ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
 
 sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
 
-- Insert the SD card in the hummingboard, power it up and U-boot messages
-should come up.
+- Insert the SD card in the board, power it up and U-boot messages should
+come up.