Add Freescale i.mx7d support

new file mode 100644
index 0000000..9d3026d
@@ -0,0 +1,13 @@
+* Clock bindings for Freescale i.MX7 Dual
+
+Required properties:
+- compatible: Should be "fsl,imx7d-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clocks: list of clock specifiers, must contain an entry for each required
+  entry in clock-names
+- clock-names: should include entries "ckil", "osc"
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx7d-clock.h
+for the full list of i.MX7 Dual clock IDs.

new file mode 100644
index 0000000..8bbf25d
@@ -0,0 +1,27 @@
+* Freescale i.MX7 Dual IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx7d-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx7d-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX7 Dual
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_PUS_100K_DOWN           (0 << 5)
+PAD_CTL_PUS_5K_UP               (1 << 5)
+PAD_CTL_PUS_47K_UP              (2 << 5)
+PAD_CTL_PUS_100K_UP             (3 << 5)
+PAD_CTL_PUE                     (1 << 4)
+PAD_CTL_HYS                     (1 << 3)
+PAD_CTL_SRE_SLOW                (1 << 2)
+PAD_CTL_SRE_FAST                (0 << 2)
+PAD_CTL_DSE_X1                  (0 << 0)
+PAD_CTL_DSE_X2                  (1 << 0)
+PAD_CTL_DSE_X3                  (2 << 0)
+PAD_CTL_DSE_X4                  (3 << 0)

new file mode 100644
index 0000000..c42cf8d
@@ -0,0 +1,486 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/imx7d-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx7d-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+	aliases {
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		gpio5 = &gpio6;
+		gpio6 = &gpio7;
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+		serial6 = &uart7;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			operating-points = <
+				/* KHz	uV */
+				996000	1075000
+				792000	975000
+			>;
+			clock-latency = <61036>; /* two CLK32 periods */
+			clocks = <&clks IMX7D_ARM_A7_ROOT_CLK>, <&clks IMX7D_ARM_A7_ROOT_SRC>,
+				 <&clks IMX7D_PLL_ARM_MAIN_CLK>, <&clks IMX7D_PLL_SYS_MAIN_CLK>;
+			clock-names = "arm", "arm_root_src", "pll_arm", "pll_sys_main";
+		};
+
+		cpu1: cpu at 1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	intc: interrupt-controller at 31001000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x31001000 0x1000>,
+		      <0x31002000 0x1000>,
+		      <0x31004000 0x2000>,
+		      <0x31006000 0x2000>;
+	};
+
+	ckil: clock-cki {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "ckil";
+	};
+
+	osc: clock-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "osc";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		aips1: aips-bus at 30000000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x30000000 0x400000>;
+			ranges;
+
+			gpio1: gpio at 30200000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30200000 0x10000>;
+				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */
+					     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio2: gpio at 30210000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30210000 0x10000>;
+				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio3: gpio at 30220000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30220000 0x10000>;
+				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio4: gpio at 30230000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30230000 0x10000>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio5: gpio at 30240000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30240000 0x10000>;
+				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio6: gpio at 30250000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30250000 0x10000>;
+				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio7: gpio at 30260000 {
+				compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+				reg = <0x30260000 0x10000>;
+				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpt1: gpt at 302d0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				reg = <0x302d0000 0x10000>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					 <&clks IMX7D_GPT1_ROOT_CLK>;
+				clock-names = "ipg", "per";
+			};
+
+			gpt2: gpt at 302e0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				reg = <0x302e0000 0x10000>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					 <&clks IMX7D_GPT2_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			gpt3: gpt at 302f0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				reg = <0x302f0000 0x10000>;
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					 <&clks IMX7D_GPT3_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			gpt4: gpt at 30300000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				reg = <0x30300000 0x10000>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					 <&clks IMX7D_GPT4_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			iomuxc: iomuxc at 30330000 {
+				compatible = "fsl,imx7d-iomuxc";
+				reg = <0x30330000 0x10000>;
+			};
+
+			gpr: iomuxc-gpr at 30340000 {
+				compatible = "fsl,imx7d-iomuxc-gpr", "syscon";
+				reg = <0x30340000 0x10000>;
+			};
+
+			ocotp: ocotp-ctrl at 30350000 {
+				compatible = "syscon";
+				reg = <0x30350000 0x10000>;
+				clocks = <&clks IMX7D_CLK_DUMMY>;
+				status = "disabled";
+			};
+
+			anatop: anatop at 30360000 {
+				compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
+					"syscon", "simple-bus";
+				reg = <0x30360000 0x10000>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+				reg_1p0d: regulator-vdd1p0d at 210 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd1p0d";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1200000>;
+					anatop-reg-offset = <0x210>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <8>;
+					anatop-min-voltage = <800000>;
+					anatop-max-voltage = <1200000>;
+					anatop-enable-bit = <31>;
+				};
+			};
+
+			snvs: snvs at 30370000 {
+				compatible = "fsl,sec-v4.0-mon", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x30370000 0x10000>;
+
+				snvs-rtc-lp at 34 {
+					compatible = "fsl,sec-v4.0-mon-rtc-lp";
+					reg = <0x34 0x58>;
+					interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
+
+			clks: ccm at 30380000 {
+				compatible = "fsl,imx7d-ccm";
+				reg = <0x30380000 0x10000>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				#clock-cells = <1>;
+				clocks = <&ckil>, <&osc>;
+				clock-names = "ckil", "osc";
+			};
+
+			src: src at 30390000 {
+				compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon";
+				reg = <0x30390000 0x10000>;
+				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+				#reset-cells = <1>;
+			};
+		};
+
+		aips3: aips-bus at 30800000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x30800000 0x400000>;
+			ranges;
+
+			uart1: serial at 30860000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30860000 0x10000>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART1_ROOT_CLK>,
+					<&clks IMX7D_UART1_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart2: serial at 30870000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30870000 0x10000>;
+				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART2_ROOT_CLK>,
+					<&clks IMX7D_UART2_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart3: serial at 30880000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30880000 0x10000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART3_ROOT_CLK>,
+					<&clks IMX7D_UART3_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			i2c1: i2c at 30a20000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+				reg = <0x30a20000 0x10000>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_I2C1_ROOT_CLK>;
+				status = "disabled";
+			};
+
+			i2c2: i2c at 30a30000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+				reg = <0x30a30000 0x10000>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_I2C2_ROOT_CLK>;
+				status = "disabled";
+			};
+
+			i2c3: i2c at 30a40000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+				reg = <0x30a40000 0x10000>;
+				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_I2C3_ROOT_CLK>;
+				status = "disabled";
+			};
+
+			i2c4: i2c at 30a50000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+				reg = <0x30a50000 0x10000>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_I2C4_ROOT_CLK>;
+				status = "disabled";
+			};
+
+			uart4: serial at 30a60000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30a60000 0x10000>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART4_ROOT_CLK>,
+					<&clks IMX7D_UART4_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart5: serial at 30a70000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30a70000 0x10000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART5_ROOT_CLK>,
+					<&clks IMX7D_UART5_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart6: serial at 30a80000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30a80000 0x10000>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART6_ROOT_CLK>,
+					<&clks IMX7D_UART6_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart7: serial at 30a90000 {
+				compatible = "fsl,imx7d-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x30a90000 0x10000>;
+				interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_UART7_ROOT_CLK>,
+					<&clks IMX7D_UART7_ROOT_CLK>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			usdhc1: usdhc at 30b40000 {
+				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+				reg = <0x30b40000 0x10000>;
+				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_USDHC1_ROOT_CLK>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: usdhc at 30b50000 {
+				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+				reg = <0x30b50000 0x10000>;
+				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_USDHC2_ROOT_CLK>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc3: usdhc at 30b60000 {
+				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+				reg = <0x30b60000 0x10000>;
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_USDHC3_ROOT_CLK>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+		};
+	};
+};

index 3a3d3e9..1d87078 100644
@@ -582,6 +582,13 @@ config SOC_IMX6SX
 	help
 	  This enables support for Freescale i.MX6 SoloX processor.
 
+config SOC_IMX7D
+	bool "i.MX7 Dual support"
+	select PINCTRL_IMX7D
+	select ARM_GIC
+	help
+		This enables support for Freescale i.MX7 Dual processor.
+
 config SOC_VF610
 	bool "Vybrid Family VF610 support"
 	select IRQ_DOMAIN_HIERARCHY

index 0622ced..40df12a 100644
@@ -85,6 +85,7 @@ endif
 obj-$(CONFIG_SOC_IMX6Q) += mach-imx6q.o
 obj-$(CONFIG_SOC_IMX6SL) += mach-imx6sl.o
 obj-$(CONFIG_SOC_IMX6SX) += mach-imx6sx.o
+obj-$(CONFIG_SOC_IMX7D) += mach-imx7d.o
 
 ifeq ($(CONFIG_SUSPEND),y)
 AFLAGS_suspend-imx6.o :=-Wa,-march=armv7-a

index 8be0a1c..bef450f 100644
@@ -23,3 +23,4 @@ obj-$(CONFIG_SOC_IMX6Q)  += clk-imx6q.o
 obj-$(CONFIG_SOC_IMX6SL) += clk-imx6sl.o
 obj-$(CONFIG_SOC_IMX6SX) += clk-imx6sx.o
 obj-$(CONFIG_SOC_VF610)  += clk-vf610.o
+obj-$(CONFIG_SOC_IMX7D)  += clk-imx7d.o

index 86217db..c0b6737 100644
@@ -313,6 +313,8 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
 	imx6sx-sabreauto.dtb \
 	imx6sx-sdb-reva.dtb \
 	imx6sx-sdb.dtb
+dtb-$(CONFIG_SOC_IMX7D) += \
+	imx7d-sdb.dtb
 dtb-$(CONFIG_SOC_LS1021A) += \
 	ls1021a-qds.dtb \
 	ls1021a-twr.dtb

420 lines not on this page · raw message

index fdeb1c8..c9c51e1f 100644
@@ -38,6 +38,7 @@ CONFIG_SOC_IMX53=y
 CONFIG_SOC_IMX6Q=y
 CONFIG_SOC_IMX6SL=y
 CONFIG_SOC_IMX6SX=y
+CONFIG_SOC_IMX7D=y
 CONFIG_SOC_VF610=y
 CONFIG_PCI=y
 CONFIG_PCI_IMX6=y