ALSA: oxygen: Fix S/PDIF muting
Subsystems (2)
PATCH 1/1 ALSA: oxygen: Fix S/PDIF muting
The S/PDIF output was muted whenever audio wasn't playing which resulted in a clicking noise from the DAC when resuming (similar to the issue in 3bef1c377d1b (ALSA: hda - stop setup_dig_out_stream() causing clicks)). Also, the mixer control wasn't actually controlling the S/PDIF output.
- Fix the initial state of the mixer to match the initial muted state.
- Mute the output at shutdown.
- Delete the code that modifies OXYGEN_SPDIF_OUT_ENABLE, and modify it only in oxygen_update_spdif_source(), so only the mixer control controls it.
---
Patch is against master, tested on 4.0.
sound/pci/oxygen/oxygen_lib.c | 5 ++++- sound/pci/oxygen/oxygen_mixer.c | 9 +++++---- sound/pci/oxygen/oxygen_pcm.c | 15 +-------------- 3 files changed, 10 insertions(+), 19 deletions(-)
sound/pci/oxygen/oxygen_lib.c +4 -1
@@ -373,7 +373,7 @@ static void oxygen_init(struct oxygen *chip)for (i =0 ; i <8 ; ++i) chip->dac_volume[i] = chip->model.dac_volume_min; chip->dac_mute =1 ; - chip->spdif_playback_enable =1 ; + chip->spdif_playback_enable =0 ; chip->spdif_bits =OXYGEN_SPDIF_C |OXYGEN_SPDIF_ORIGINAL | (IEC958_AES1_CON_PCM_CODER <<OXYGEN_SPDIF_CATEGORY_SHIFT ); chip->spdif_pcm_bits = chip->spdif_bits;
@@ -575,6 +575,9 @@ static void oxygen_shutdown(struct oxygen *chip)spin_lock_irq (&chip->reg_lock); chip->interrupt_mask =0 ; chip->pcm_running =0 ; + chip->spdif_playback_enable =0 ; +oxygen_clear_bits32 (chip,OXYGEN_SPDIF_CONTROL , +OXYGEN_SPDIF_OUT_ENABLE );oxygen_write16 (chip,OXYGEN_DMA_STATUS ,0 );oxygen_write16 (chip,OXYGEN_INTERRUPT_MASK ,0 );spin_unlock_irq (&chip->reg_lock);
sound/pci/oxygen/oxygen_mixer.c +5 -4
@@ -252,7 +252,6 @@ void oxygen_update_spdif_source(struct oxygen *chip) old_control =oxygen_read32 (chip,OXYGEN_SPDIF_CONTROL ); old_routing =oxygen_read16 (chip,OXYGEN_PLAY_ROUTING );if (chip->pcm_active & (1 <<PCM_SPDIF )) { - new_control = old_control |OXYGEN_SPDIF_OUT_ENABLE ; new_routing = (old_routing & ~OXYGEN_PLAY_SPDIF_MASK ) |OXYGEN_PLAY_SPDIF_SPDIF ; oxygen_rate = (old_control >>OXYGEN_SPDIF_OUT_RATE_SHIFT )
@@ -265,13 +264,15 @@ void oxygen_update_spdif_source(struct oxygen *chip) oxygen_rate =oxygen_read16 (chip,OXYGEN_I2S_MULTICH_FORMAT ) &OXYGEN_I2S_RATE_MASK ; new_control = (old_control & ~OXYGEN_SPDIF_OUT_RATE_MASK ) | - (oxygen_rate <<OXYGEN_SPDIF_OUT_RATE_SHIFT ) | -OXYGEN_SPDIF_OUT_ENABLE ; + (oxygen_rate <<OXYGEN_SPDIF_OUT_RATE_SHIFT ); }else { - new_control = old_control & ~OXYGEN_SPDIF_OUT_ENABLE ; new_routing = old_routing; oxygen_rate =OXYGEN_RATE_44100 ; } +if (chip->spdif_playback_enable) + new_control = old_control |OXYGEN_SPDIF_OUT_ENABLE ; +else + new_control = old_control & ~OXYGEN_SPDIF_OUT_ENABLE ;if (old_routing != new_routing) {oxygen_write32 (chip,OXYGEN_SPDIF_CONTROL , new_control & ~OXYGEN_SPDIF_OUT_ENABLE );
sound/pci/oxygen/oxygen_pcm.c +1 -14
@@ -477,8 +477,6 @@ static int oxygen_spdif_hw_params(struct snd_pcm_substream *substream,mutex_lock (&chip->mutex);spin_lock_irq (&chip->reg_lock); -oxygen_clear_bits32 (chip,OXYGEN_SPDIF_CONTROL , -OXYGEN_SPDIF_OUT_ENABLE );oxygen_write8_masked (chip,OXYGEN_PLAY_FORMAT ,oxygen_format (hw_params) <<OXYGEN_SPDIF_FORMAT_SHIFT ,OXYGEN_SPDIF_FORMAT_MASK );
@@ -544,17 +542,6 @@ static int oxygen_hw_free(struct snd_pcm_substream *substream)return snd_pcm_lib_free_pages (substream); } -static int oxygen_spdif_hw_free (struct snd_pcm_substream *substream) -{ -struct oxygen *chip =snd_pcm_substream_chip (substream); - -spin_lock_irq (&chip->reg_lock); -oxygen_clear_bits32 (chip,OXYGEN_SPDIF_CONTROL , -OXYGEN_SPDIF_OUT_ENABLE ); -spin_unlock_irq (&chip->reg_lock); -return oxygen_hw_free (substream); -} -static int oxygen_prepare (struct snd_pcm_substream *substream) {struct oxygen *chip =snd_pcm_substream_chip (substream);
@@ -669,7 +656,7 @@ static struct snd_pcm_ops oxygen_spdif_ops = { .close = oxygen_close, .ioctl = snd_pcm_lib_ioctl, .hw_params = oxygen_spdif_hw_params, - .hw_free = oxygen_spdif_hw_free, + .hw_free = oxygen_hw_free, .prepare = oxygen_prepare, .trigger = oxygen_trigger, .pointer = oxygen_pointer,
Signature · 1 line
2.3.5
Clemens Ladisch
maintainerQuoted 2 lines · Laurence Darby
The S/PDIF output was muted whenever audio wasn't playing which resulted in a clicking noise from the DAC when resuming
It indeed appears that there are too many oxygen_clear_bits32() calls. However, I don't trust the hardware; please confirm that the S/PDIF output, without an active stream, play zeros and not the last sample.
Quoted 1 line
Also, the mixer control wasn't actually controlling the S/PDIF output.
Because that is not its purpose to begin with. >:-)
The mixer control enables copying the "Multichannel" device to the S/PDIF output. The "Digital" device has no mute, and takes precedence over the multichannel device when both are active.
Regards,
Clemens
Quoted 7 lines · On Sun, 28 Jun 2015 20:44:26 +0200 Clemens Ladisch wrote:
Quoted 2 lines · Laurence Darby
The S/PDIF output was muted whenever audio wasn't playing which resulted in a clicking noise from the DAC when resuming
It indeed appears that there are too many
oxygen_clear_bits32()calls. However, I don't trust the hardware; please confirm that the S/PDIF output, without an active stream, play zeros and not the last sample.
Well, to test that I created a wav file of about a quarter of a sine wave (at about -15dB), consisting of 5520 samples, so it matched the alsa buffer size, otherwise aplay pads the buffer with silence.
The chip does continue playing the last sample value, then the speakers pop later when something else is played. Is this really an issue though? I just found my intel hda chip behaves the same way, and that chip's driver leaves it un-muted.
If this is still going to prevent fixing the popping noise for the oxygen chip, what about writing a single 0x00 sample to it in the driver instead of muting it?
Quoted 10 lines
Quoted 3 lines
Also, the mixer control wasn't actually controlling the S/PDIF output.
Because that is not its purpose to begin with. >:-)
The mixer control enables copying the "Multichannel" device to the S/PDIF output. The "Digital" device has no mute, and takes precedence over the multichannel device when both are active.
All my other sound cards (hda, cmedia & emu10k) have an S/PDIF mixer control that mutes the output (i.e. causes the DAC to lose the signal), in the same way as disabling OXYGEN_SPDIF_OUT_ENABLE does, so I would say that it does have mute, and I thought it should be controlled by the variable called "spdif_playback_enable"...
Would an acceptable fix be to create another mixer control for muting (and also rename the existing S/PDIF to e.g. "S/PDIF Multichannel" so its clearer what that's for)?
Regards,
Laurence
Clemens Ladisch
maintainerQuoted 9 lines · Laurence Darby
Quoted 7 lines · On Sun, 28 Jun 2015 20:44:26 +0200 Clemens Ladisch wrote:
Quoted 2 lines · Laurence Darby
The S/PDIF output was muted whenever audio wasn't playing which resulted in a clicking noise from the DAC when resuming
It indeed appears that there are too many
oxygen_clear_bits32()calls. However, I don't trust the hardware; please confirm that the S/PDIF output, without an active stream, play zeros and not the last sample.
Quoted 8 lines
Well, to test that I created a wav file of about a quarter of a sine wave (at about -15dB), consisting of 5520 samples, so it matched the alsa buffer size, otherwise aplay pads the buffer with silence.
The chip does continue playing the last sample value, then the speakers pop later when something else is played. Is this really an issue though? I just found my intel hda chip behaves the same way, and that chip's driver leaves it un-muted.
The current problem is that the output gets disabled, then later, when the driver is about to start the new stream, it enables the output again (which outputs the last old sample), and then the new stream starts (usually with zero samples). Going from disabled(=zero) to old-sample to new-sample(=zero) is an extra pop.
In any case, putting a DC offset on the speakers is a bad idea.
Quoted 3 lines
If this is still going to prevent fixing the popping noise for the oxygen chip, what about writing a single
0x00sample to it in the driver instead of muting it?
This is likely to work (but the zero sample has to go through DMA).
At the moment, oxygen_hw_free() pokes at the OXYGEN_DMA_FLUSH register. Please check if there is an improvement if it also pokes at the OXYGEN_DMA_RESET register.
Quoted 9 lines
Quoted 8 lines
Quoted 2 lines
Also, the mixer control wasn't actually controlling the S/PDIF output.
Because that is not its purpose to begin with. >:-)
The mixer control enables copying the "Multichannel" device to the S/PDIF output. The "Digital" device has no mute, and takes precedence over the multichannel device when both are active.
Quoted 5 lines
All my other sound cards (hda, cmedia & emu10k) have an S/PDIF mixer control that mutes the output (i.e. causes the DAC to lose the signal), in the same way as disabling
OXYGEN_SPDIF_OUT_ENABLEdoes, so I would say that it does have mute, and I thought it should be controlled by the variable called "spdif_playback_enable"...
I don't remember what the reason for the behaviour of the current controls was; I probably copied them from some other driver.
Quoted 3 lines
Would an acceptable fix be to create another mixer control for muting (and also rename the existing S/PDIF to e.g. "S/PDIF Multichannel" so its clearer what that's for)?
AFAICS the usual name would be "PCM".
When making separate changes, please send separate patches.
Regards,
Clemens
Quoted 26 lines · On Tue, 30 Jun 2015 11:43:52 +0200 Clemens Ladisch wrote:
Quoted 10 lines · Laurence Darby
Quoted 8 lines · On Sun, 28 Jun 2015 20:44:26 +0200 Clemens Ladisch wrote:
Quoted 2 lines · Laurence Darby
The S/PDIF output was muted whenever audio wasn't playing which resulted in a clicking noise from the DAC when resuming
It indeed appears that there are too many
oxygen_clear_bits32()calls. However, I don't trust the hardware; please confirm that the S/PDIF output, without an active stream, play zeros and not the last sample.Quoted 8 lines
Well, to test that I created a wav file of about a quarter of a sine wave (at about -15dB), consisting of 5520 samples, so it matched the alsa buffer size, otherwise aplay pads the buffer with silence.
The chip does continue playing the last sample value, then the speakers pop later when something else is played. Is this really an issue though? I just found my intel hda chip behaves the same way, and that chip's driver leaves it un-muted.
The current problem is that the output gets disabled, then later, when the driver is about to start the new stream, it enables the output again (which outputs the last old sample), and then the new stream starts (usually with zero samples). Going from disabled(=zero) to old-sample to new-sample(=zero) is an extra pop.
Quoted 7 lines
In any case, putting a DC offset on the speakers is a bad idea.
Quoted 3 lines
If this is still going to prevent fixing the popping noise for the oxygen chip, what about writing a single
0x00sample to it in the driver instead of muting it?This is likely to work (but the zero sample has to go through DMA).
Ok, I eventually got this to work, with this in oxygen_spdif_hw_free():
memset (runtime->dma_area, 0, runtime->dma_bytes); oxygen_trigger(substream,SNDRV_PCM_TRIGGER_START); msleep (1); oxygen_trigger(substream,SNDRV_PCM_TRIGGER_STOP);
instead of disabling OXYGEN_SPDIF_OUT_ENABLE. The 1ms sleep is necessary otherwise it intermittently still leaves DC on the output.
If I create a proper patch for that (it should probably use snd_pcm_format_set_silence() instead of memset) would that be acceptable?
Quoted 3 lines
At the moment,
oxygen_hw_free()pokes at theOXYGEN_DMA_FLUSHregister. Please check if there is an improvement if it also pokes at theOXYGEN_DMA_RESETregister.
Unfortunately not. I did some archeology and found your CVS commit from 2007: http://sourceforge.net/p/alsa/mailman/message/15439076/
which has this code:
+ if (chip->CMI8788IC_revision == CMI8788IC_Revision1)
+ DMARestRegister = PCI_DMA_Reset;
+ if (chip->CMI8788IC_revision == CMI8788IC_Revision2)
+ DMARestRegister = PCI_DMA_FLUSH;
...
+ /* Reset DMA Channel*/
+ reset = snd_cmipci_read_b(chip, DMARestRegister);
+ reset |= cmi_subs->DMA_chan_reset; /* set bit */
So I understand why you asked if the RESET works :)
Regards,
Laurence
Clemens Ladisch
maintainerQuoted 6 lines · Laurence Darby
Quoted 5 lines · On Tue, 30 Jun 2015 11:43:52 +0200 Clemens Ladisch wrote:
Quoted 3 lines · Laurence Darby
If this is still going to prevent fixing the popping noise for the oxygen chip, what about writing a single
0x00sample to it in the driver instead of muting it?
Quoted 8 lines
Quoted 1 line
This is likely to work (but the zero sample has to go through DMA).
Ok, I eventually got this to work, with this in
oxygen_spdif_hw_free():memset (runtime->dma_area, 0, runtime->dma_bytes); oxygen_trigger(substream,SNDRV_PCM_TRIGGER_START); msleep (1); oxygen_trigger(substream,SNDRV_PCM_TRIGGER_STOP);
Please note that hw_free can be called without a valid configuration.
Calling oxygen_trigger() might affect other streams.
Quoted 2 lines
If I create a proper patch for that (it should probably use
snd_pcm_format_set_silence()instead of memset)
All supported sample formats uses plain zeros.
Regards,
Clemens