ARM: dts: Add binding documentation for AXP20x pmic usb power supply

From: Bruno Pr?mont <[email protected]>

Add an extra set of registers which is necessary tu support the PMICs battery charger function, and mark registers which contain status bits, gpio status, and adc readings as volatile.

Cc Bruno Pr?mont <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

From: Bruno Pr?mont <[email protected]>

Add an extra set of registers which is necessary tu support the PMICs battery charger function, and mark registers which contain status bits, gpio status, and adc readings as volatile.

Cc Bruno Pr?mont <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:
-Add a AXP20X_OCV_MAX define
Changes in v3:
-Add Bruno's S-o-b

---
 drivers/mfd/axp20x.c       | 8 +++++++-
 include/linux/mfd/axp20x.h | 6 ++++++
 2 files changed, 13 insertions(+), 1 deletion(-)

drivers/mfd/axp20x.c +7 -1

index 6df9155..f9a3c2d 100644
@@ -39,10 +39,16 @@ static const char * const axp20x_model_names[] = {
 static const struct regmap_range axp20x_writeable_ranges[] = {
 	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
 	regmap_reg_range(AXP20X_DCDC_MODE, AXP20X_FG_RES),
+	regmap_reg_range(AXP20X_RDC_H, AXP20X_OCV(15)),
 };
 
 static const struct regmap_range axp20x_volatile_ranges[] = {
+	regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP20X_USB_OTG_STATUS),
+	regmap_reg_range(AXP20X_CHRG_CTRL1, AXP20X_CHRG_CTRL2),
 	regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ5_STATE),
+	regmap_reg_range(AXP20X_ACIN_V_ADC_H, AXP20X_IPSOUT_V_HIGH_L),
+	regmap_reg_range(AXP20X_GPIO20_SS, AXP20X_GPIO3_CTRL),
+	regmap_reg_range(AXP20X_FG_RES, AXP20X_RDC_L),
 };
 
 static const struct regmap_access_table axp20x_writeable_table = {

@@ -159,7 +165,7 @@ static const struct regmap_config axp20x_regmap_config = {
 	.val_bits	= 8,
 	.wr_table	= &axp20x_writeable_table,
 	.volatile_table	= &axp20x_volatile_table,
-	.max_register	= AXP20X_FG_RES,
+	.max_register	= AXP20X_OCV(AXP20X_OCV_MAX),
 	.cache_type	= REGCACHE_RBTREE,
 };
 

include/linux/mfd/axp20x.h +6 -0

index 5275423..6d8b39a 100644
@@ -151,6 +151,12 @@ enum {
 #define AXP20X_CC_CTRL			0xb8
 #define AXP20X_FG_RES			0xb9
 
+/* OCV */
+#define AXP20X_RDC_H			0xba
+#define AXP20X_RDC_L			0xbb
+#define AXP20X_OCV(m)			(0xc0 + (m))
+#define AXP20X_OCV_MAX			0xf
+
 /* AXP22X specific registers */
 #define AXP22X_BATLOW_THRES1		0xe6
 

Add a cell for the usb power_supply part of the axp20x PMICs.

Note that this cell is only for the usb power_supply part and not the ac-power / battery-charger / rtc-backup-bat-charger bits.

Depending on the board each of those must be enabled / disabled separately in devicetree as most boards do not use all 4. So in dt each one needs its own child-node of the axp20x node. Another reason for using separate child nodes for each is so that other devicetree nodes can have a power-supply property with a phandle referencing a node representing a single power-supply.

The decision to use a separate devicetree node for each is reflected on the kernel side by each getting its own mfd-cell / platform_device and platform-driver.

Note this commit also makes some whitespace changes to the intialization of existing cells in axp20x_cells, these are pure whitespace changes, functionally nothing changes.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

Add a cell for the usb power_supply part of the axp20x PMICs.

Note that this cell is only for the usb power_supply part and not the ac-power / battery-charger / rtc-backup-bat-charger bits.

Depending on the board each of those must be enabled / disabled separately in devicetree as most boards do not use all 4. So in dt each one needs its own child-node of the axp20x node. Another reason for using separate child nodes for each is so that other devicetree nodes can have a power-supply property with a phandle referencing a node representing a single power-supply.

The decision to use a separate devicetree node for each is reflected on the kernel side by each getting its own mfd-cell / platform_device and platform-driver.

Note this commit also makes some whitespace changes to the intialization of existing cells in axp20x_cells, these are pure whitespace changes, functionally nothing changes.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -2

-Use DEFINE_RES_IRQ_NAMED
-Change indentation of axp20x_cells initializers to avoid line wrapping

Changes in v3:

drivers/mfd/axp20x.c +16 -4

index f9a3c2d..ca4a604 100644
@@ -113,6 +113,13 @@ static struct resource axp20x_pek_resources[] = {
 	},
 };
 
+static struct resource axp20x_usb_power_supply_resources[] = {
+	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
+	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
+	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_VBUS_VALID, "VBUS_VALID"),
+	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_VBUS_NOT_VALID, "VBUS_NOT_VALID"),
+};
+
 static struct resource axp22x_pek_resources[] = {
 	{
 		.name   = "PEK_DBR",

@@ -363,11 +370,16 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
 
 static struct mfd_cell axp20x_cells[] = {
 	{
-		.name			= "axp20x-pek",
-		.num_resources		= ARRAY_SIZE(axp20x_pek_resources),
-		.resources		= axp20x_pek_resources,
+		.name		= "axp20x-pek",
+		.num_resources	= ARRAY_SIZE(axp20x_pek_resources),
+		.resources	= axp20x_pek_resources,
 	}, {
-		.name			= "axp20x-regulator",
+		.name		= "axp20x-regulator",
+	}, {
+		.name		= "axp20x-usb-power-supply",
+		.of_compatible	= "x-powers,axp202-usb-power-supply",
+		.num_resources	= ARRAY_SIZE(axp20x_usb_power_supply_resources),
+		.resources	= axp20x_usb_power_supply_resources,
 	},
 };
 

Quoted 29 lines · Hans de Goede

Add a cell for the usb power_supply part of the axp20x PMICs.

Note that this cell is only for the usb power_supply part and not the ac-power / battery-charger / rtc-backup-bat-charger bits.

Depending on the board each of those must be enabled / disabled separately in devicetree as most boards do not use all 4. So in dt each one needs its own child-node of the axp20x node. Another reason for using separate child nodes for each is so that other devicetree nodes can have a power-supply property with a phandle referencing a node representing a single power-supply.

The decision to use a separate devicetree node for each is reflected on the kernel side by each getting its own mfd-cell / platform_device and platform-driver.

Note this commit also makes some whitespace changes to the intialization of existing cells in axp20x_cells, these are pure whitespace changes, functionally nothing changes.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -2

-Use DEFINE_RES_IRQ_NAMED
-Change indentation of axp20x_cells initializers to avoid line wrapping

Changes in v3:

Review

Quoted 5 lines

(quoted diff) +0 -3

-Improve commit message
-Add Bruno's S-o-b
---
  drivers/mfd/axp20x.c | 20 ++++++++++++++++----
  1 file changed, 16 insertions(+), 4 deletions(-)

For my own reference:

Acked-by Lee Jones <[email protected]>

Are these two patches tied to any other in the set, or can I apply them separately?

Quoted 38 lines · Lee Jones

Quoted 29 lines · Hans de Goede

Add a cell for the usb power_supply part of the axp20x PMICs.

Note that this cell is only for the usb power_supply part and not the ac-power / battery-charger / rtc-backup-bat-charger bits.

Depending on the board each of those must be enabled / disabled separately in devicetree as most boards do not use all 4. So in dt each one needs its own child-node of the axp20x node. Another reason for using separate child nodes for each is so that other devicetree nodes can have a power-supply property with a phandle referencing a node representing a single power-supply.

The decision to use a separate devicetree node for each is reflected on the kernel side by each getting its own mfd-cell / platform_device and platform-driver.

Note this commit also makes some whitespace changes to the intialization of existing cells in axp20x_cells, these are pure whitespace changes, functionally nothing changes.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -2

-Use DEFINE_RES_IRQ_NAMED
-Change indentation of axp20x_cells initializers to avoid line wrapping

Changes in v3:

Review

Quoted 5 lines

(quoted diff) +0 -3

-Improve commit message
-Add Bruno's S-o-b
---
 drivers/mfd/axp20x.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

For my own reference:

Quoted 4 lines

Acked-by Lee Jones <[email protected]>

Are these two patches tied to any other in the set, or can I apply them separately?

You can apply them seperately, thanks.

I'm wondering who will take care of upstreaming the first patch of this
set: "ARM: dts: Add binding documentation for AXP20x pmic usb power supply"

If you can take that one too that would be great.

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -3

-Split out the dt-bindings documentation into a separate patch
-Renamed axp20x_read_16bit to axp20x_read_variable_width
-Use better local variable names inside axp20x_read_variable_width

Changes in v3:
-Add Bruno's S-o-b

---
 drivers/power/Kconfig            |   7 ++
 drivers/power/Makefile           |   1 +
 drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h       |  24 ++++
 4 files changed, 275 insertions(+)
 create mode 100644 drivers/power/axp20x_usb_power.c

drivers/power/Kconfig +7 -0

index 4091fb0..1fee60c 100644
@@ -439,6 +439,13 @@ config BATTERY_RT5033
 	  The fuelgauge calculates and determines the battery state of charge
 	  according to battery open circuit voltage.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
 source "drivers/power/reset/Kconfig"
 
 endif # POWER_SUPPLY

drivers/power/Makefile +1 -0

index b7b0181..ae0f27d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY)	+= generic-adc-battery.o
 
 obj-$(CONFIG_PDA_POWER)		+= pda_power.o
 obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
 obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
 obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
 obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o

drivers/power/axp20x_usb_power.c new file +53 -0

new file mode 100644
index 0000000..09f388e
@@ -0,0 +1,243 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <[email protected]>
+ * Copyright (C) 2014 Bruno Pr?mont <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);

drivers/power/axp20x_usb_power.c new file +180 -0

+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		val->intval = AXP20X_VBUS_VHOLD_uV(v);
+		return 0;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_V_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 1700; /* 1 step = 1.7 mV */
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;
+			break;
+		}
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_I_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 375; /* 1 step = 0.375 mA */
+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (r)
+		return r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (r)
+			return r;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)
+{
+	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct axp20x_usb_power *power;
+	static const char * const irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	int i, irq, r;
+
+	if (!of_device_is_available(pdev->dev.of_node))
+		return -ENODEV;
+
+	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	power->regmap = axp20x->regmap;
+
+	/* Enable vbus valid checking */
+	r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (r)
+		return r;
+
+	/* Enable vbus voltage and current measurement */
+	r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (r)
+		return r;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		r = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (r < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], r);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");

include/linux/mfd/axp20x.h +15 -0

index 6d8b39a..8ec996e 100644
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MFD_AXP20X_H
 #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
 enum {
 	AXP202_ID = 0,
 	AXP209_ID,

@@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
 	struct gpio_desc *gpio_mux_cntl;
 };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+

W dniu 26.06.2015 o 19:59, Hans de Goede pisze:

Quoted 22 lines

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -3

-Split out the dt-bindings documentation into a separate patch
-Renamed axp20x_read_16bit to axp20x_read_variable_width
-Use better local variable names inside axp20x_read_variable_width

Quoted 2 lines

Changes in v3:
-Add Bruno's S-o-b

Hi,

Two minor comments below, the driver itself looks good.

Quoted 103 lines

---
 drivers/power/Kconfig            |   7 ++
 drivers/power/Makefile           |   1 +
 drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h       |  24 ++++
 4 files changed, 275 insertions(+)
 create mode 100644 drivers/power/axp20x_usb_power.c

drivers/power/Kconfig +7 -0

index 4091fb0..1fee60c 100644
@@ -439,6 +439,13 @@ config BATTERY_RT5033
 	  The fuelgauge calculates and determines the battery state of charge
 	  according to battery open circuit voltage.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
 source "drivers/power/reset/Kconfig"
 
 endif # POWER_SUPPLY

drivers/power/Makefile +1 -0

index b7b0181..ae0f27d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY)	+= generic-adc-battery.o
 
 obj-$(CONFIG_PDA_POWER)		+= pda_power.o
 obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
 obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
 obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
 obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o

drivers/power/axp20x_usb_power.c new file +59 -0

new file mode 100644
index 0000000..09f388e
@@ -0,0 +1,243 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <[email protected]>
+ * Copyright (C) 2014 Bruno Pr?mont <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);
+
+	return IRQ_HANDLED;
+}
+
+static int axp20x_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)

drivers/power/axp20x_usb_power.c line 63

Quoted 4 lines

drivers/power/axp20x_usb_power.c new file +4 -0

+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int input, v;
+	int r;

Here and in probe function - it is strictly personal but I don't like the 'r' variable. I got used to 'err' or 'ret' which are more descriptive to me. 'r' may look like 'resource' for example.

Quoted 216 lines

drivers/power/axp20x_usb_power.c new file +180 -0

+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		val->intval = AXP20X_VBUS_VHOLD_uV(v);
+		return 0;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_V_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 1700; /* 1 step = 1.7 mV */
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;
+			break;
+		}
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_I_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 375; /* 1 step = 0.375 mA */
+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (r)
+		return r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (r)
+			return r;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)
+{
+	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct axp20x_usb_power *power;
+	static const char * const irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	int i, irq, r;
+
+	if (!of_device_is_available(pdev->dev.of_node))
+		return -ENODEV;
+
+	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	power->regmap = axp20x->regmap;
+
+	/* Enable vbus valid checking */
+	r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (r)
+		return r;
+
+	/* Enable vbus voltage and current measurement */
+	r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (r)
+		return r;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		r = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (r < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], r);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");

include/linux/mfd/axp20x.h +21 -0

index 6d8b39a..8ec996e 100644
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MFD_AXP20X_H
 #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
 enum {
 	AXP202_ID = 0,
 	AXP209_ID,

@@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
 	struct gpio_desc *gpio_mux_cntl;
 };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+
+	err = regmap_read(regmap, reg + 1, &reg_val);
+	if (err)
+		return err;
+
+	result |= reg_val;
+

include/linux/mfd/axp20x.h struct axp288_extcon_pdata { · line 399

Quoted 4 lines

include/linux/mfd/axp20x.h +3 -0

+	return result;
+}
+
 #endif /* __LINUX_MFD_AXP20X_H */

Is this static inline function used outside of drivers/power/axp20x_usb_power.c? Looks like it isn't, but maybe you have a plan for it? If not, then it shouldn't be in header file.

Best regards,
Krzysztof

Quoted 134 lines

W dniu 26.06.2015 o 19:59, Hans de Goede pisze:

Quoted 22 lines

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -3

-Split out the dt-bindings documentation into a separate patch
-Renamed axp20x_read_16bit to axp20x_read_variable_width
-Use better local variable names inside axp20x_read_variable_width

Quoted 2 lines

Changes in v3:
-Add Bruno's S-o-b

Hi,

Two minor comments below, the driver itself looks good.

Quoted 103 lines

---
 drivers/power/Kconfig            |   7 ++
 drivers/power/Makefile           |   1 +
 drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h       |  24 ++++
 4 files changed, 275 insertions(+)
 create mode 100644 drivers/power/axp20x_usb_power.c

drivers/power/Kconfig +7 -0

index 4091fb0..1fee60c 100644
@@ -439,6 +439,13 @@ config BATTERY_RT5033
 	  The fuelgauge calculates and determines the battery state of charge
 	  according to battery open circuit voltage.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
 source "drivers/power/reset/Kconfig"
 
 endif # POWER_SUPPLY

drivers/power/Makefile +1 -0

index b7b0181..ae0f27d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY)	+= generic-adc-battery.o
 
 obj-$(CONFIG_PDA_POWER)		+= pda_power.o
 obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
 obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
 obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
 obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o

drivers/power/axp20x_usb_power.c new file +59 -0

new file mode 100644
index 0000000..09f388e
@@ -0,0 +1,243 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <[email protected]>
+ * Copyright (C) 2014 Bruno Pr?mont <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);
+
+	return IRQ_HANDLED;
+}
+
+static int axp20x_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)

Quoted 8 lines

drivers/power/axp20x_usb_power.c line 63

Quoted 4 lines

drivers/power/axp20x_usb_power.c new file +4 -0

+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int input, v;
+	int r;

Here and in probe function - it is strictly personal but I don't like the 'r' variable. I got used to 'err' or 'ret' which are more descriptive to me. 'r' may look like 'resource' for example.

'ret' might work but doesn't it imply return value for this function instead of return value from a called function?

Quoted 217 lines

Quoted 217 lines

drivers/power/axp20x_usb_power.c new file +180 -0

+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		val->intval = AXP20X_VBUS_VHOLD_uV(v);
+		return 0;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_V_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 1700; /* 1 step = 1.7 mV */
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;
+			break;
+		}
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_I_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 375; /* 1 step = 0.375 mA */
+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (r)
+		return r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (r)
+			return r;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)
+{
+	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct axp20x_usb_power *power;
+	static const char * const irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	int i, irq, r;
+
+	if (!of_device_is_available(pdev->dev.of_node))
+		return -ENODEV;
+
+	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	power->regmap = axp20x->regmap;
+
+	/* Enable vbus valid checking */
+	r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (r)
+		return r;
+
+	/* Enable vbus voltage and current measurement */
+	r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (r)
+		return r;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		r = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (r < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], r);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");

include/linux/mfd/axp20x.h +21 -0

index 6d8b39a..8ec996e 100644
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MFD_AXP20X_H
 #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
 enum {
 	AXP202_ID = 0,
 	AXP209_ID,

@@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
 	struct gpio_desc *gpio_mux_cntl;
 };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+
+	err = regmap_read(regmap, reg + 1, &reg_val);
+	if (err)
+		return err;
+
+	result |= reg_val;
+

Quoted 8 lines

include/linux/mfd/axp20x.h struct axp288_extcon_pdata { · line 399

Quoted 4 lines

include/linux/mfd/axp20x.h +3 -0

+	return result;
+}
+
 #endif /* __LINUX_MFD_AXP20X_H */

Is this static inline function used outside of drivers/power/axp20x_usb_power.c? Looks like it isn't, but maybe you have a plan for it? If not, then it shouldn't be in header file.

See comments for first iteration of this patch:

| | This is only used twice and only in one file.
| |
| | Do you know of any other uses of this call that will be upstreamed
| | shortly?  
| 
| Yes I plan to write drivers for the other 3 power_supply class
| cells (ac-power, battery-charger, rtc-bat-charger) in the axp209,
| and most of those need the same helper which I why I put it here.  

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -3

-Split out the dt-bindings documentation into a separate patch
-Renamed axp20x_read_16bit to axp20x_read_variable_width
-Use better local variable names inside axp20x_read_variable_width

Changes in v3:

(quoted diff) +0 -2

-Add Bruno's S-o-b
---
 drivers/power/Kconfig            |   7 ++
 drivers/power/Makefile           |   1 +
 drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h       |  24 ++++
 4 files changed, 275 insertions(+)
 create mode 100644 drivers/power/axp20x_usb_power.c

drivers/power/Kconfig +7 -0

index 4091fb0..1fee60c 100644
@@ -439,6 +439,13 @@ config BATTERY_RT5033
 	  The fuelgauge calculates and determines the battery state of charge
 	  according to battery open circuit voltage.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
 source "drivers/power/reset/Kconfig"
 
 endif # POWER_SUPPLY

drivers/power/Makefile +1 -0

index b7b0181..ae0f27d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY)	+= generic-adc-battery.o
 
 obj-$(CONFIG_PDA_POWER)		+= pda_power.o
 obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
 obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
 obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
 obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o

drivers/power/axp20x_usb_power.c new file +69 -0

new file mode 100644
index 0000000..09f388e
@@ -0,0 +1,243 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <[email protected]>
+ * Copyright (C) 2014 Bruno Pr?mont <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);
+
+	return IRQ_HANDLED;
+}
+
+static int axp20x_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)
+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int input, v;
+	int r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;

drivers/power/axp20x_usb_power.c new file +18 -0

+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;

drivers/power/axp20x_usb_power.c new file +60 -0

+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (r)
+		return r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (r)
+			return r;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)

drivers/power/axp20x_usb_power.c new file +60 -0

+
+	/* Enable vbus valid checking */
+	r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (r)
+		return r;
+
+	/* Enable vbus voltage and current measurement */
+	r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (r)
+		return r;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		r = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (r < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], r);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");

include/linux/mfd/axp20x.h +24 -0

index 6d8b39a..8ec996e 100644
@@ -11,6 +11,8 @@
 #ifndef __LINUX_MFD_AXP20X_H
 #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
 enum {
 	AXP202_ID = 0,
 	AXP209_ID,

@@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
 	struct gpio_desc *gpio_mux_cntl;
 };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+
+	err = regmap_read(regmap, reg + 1, &reg_val);
+	if (err)
+		return err;
+
+	result |= reg_val;
+
+	return result;
+}
+
 #endif /* __LINUX_MFD_AXP20X_H */

Signature · 1 line

2.4.3

Hi,

Quoted 142 lines · Hans de Goede

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Cc Bruno Pr?mont <[email protected]>

Acked-by Lee Jones <[email protected]>

Signed-off-by Bruno Pr?mont <[email protected]>

Signed-off-by Hans de Goede <[email protected]>

---
Changes in v2:

(quoted diff) +0 -3

-Split out the dt-bindings documentation into a separate patch
-Renamed axp20x_read_16bit to axp20x_read_variable_width
-Use better local variable names inside axp20x_read_variable_width

Changes in v3:

(quoted diff) +0 -2

-Add Bruno's S-o-b
---
  drivers/power/Kconfig            |   7 ++
  drivers/power/Makefile           |   1 +
  drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
  include/linux/mfd/axp20x.h       |  24 ++++
  4 files changed, 275 insertions(+)
  create mode 100644 drivers/power/axp20x_usb_power.c

drivers/power/Kconfig +7 -0

index 4091fb0..1fee60c 100644
@@ -439,6 +439,13 @@ config BATTERY_RT5033
  	  The fuelgauge calculates and determines the battery state of charge
  	  according to battery open circuit voltage.
 
+config AXP20X_POWER
+	tristate "AXP20x power supply driver"
+	depends on MFD_AXP20X
+	help
+	  This driver provides support for the power supply features of
+	  AXP20x PMIC.
+
  source "drivers/power/reset/Kconfig"
 
  endif # POWER_SUPPLY

drivers/power/Makefile +1 -0

index b7b0181..ae0f27d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY)	+= generic-adc-battery.o
 
  obj-$(CONFIG_PDA_POWER)		+= pda_power.o
  obj-$(CONFIG_APM_POWER)		+= apm_power.o
+obj-$(CONFIG_AXP20X_POWER)	+= axp20x_usb_power.o
  obj-$(CONFIG_MAX8925_POWER)	+= max8925_power.o
  obj-$(CONFIG_WM831X_BACKUP)	+= wm831x_backup.o
  obj-$(CONFIG_WM831X_POWER)	+= wm831x_power.o

drivers/power/axp20x_usb_power.c new file +74 -0

new file mode 100644
index 0000000..09f388e
@@ -0,0 +1,243 @@
+/*
+ * AXP20x PMIC USB power supply status driver
+ *
+ * Copyright (C) 2015 Hans de Goede <[email protected]>
+ * Copyright (C) 2014 Bruno Pr?mont <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under  the terms of the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define DRVNAME "axp20x-usb-power-supply"
+
+#define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
+#define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
+
+#define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
+
+#define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
+#define AXP20X_VBUS_CLIMIT_MASK		3
+#define AXP20X_VBUC_CLIMIT_900mA	0
+#define AXP20X_VBUC_CLIMIT_500mA	1
+#define AXP20X_VBUC_CLIMIT_100mA	2
+#define AXP20X_VBUC_CLIMIT_NONE		3
+
+#define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
+#define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
+
+#define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
+
+struct axp20x_usb_power {
+	struct regmap *regmap;
+	struct power_supply *supply;
+};
+
+static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
+{
+	struct axp20x_usb_power *power = devid;
+
+	power_supply_changed(power->supply);
+
+	return IRQ_HANDLED;
+}
+
+static int axp20x_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)
+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int input, v;
+	int r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		val->intval = AXP20X_VBUS_VHOLD_uV(v);
+		return 0;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		r = axp20x_read_variable_width(power->regmap,

drivers/power/axp20x_usb_power.c line 79

Quoted 5 lines

drivers/power/axp20x_usb_power.c new file +5 -0

+					       AXP20X_VBUS_V_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 1700; /* 1 step = 1.7 mV */

Eventually, as we will have more users (the various power supplies, the TS pin?), we should have an IIO driver for the internal ADC.

Do you know how close it is from the AXP288's ?

Quoted 18 lines

drivers/power/axp20x_usb_power.c new file +18 -0

+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+		r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+		if (r)
+			return r;
+
+		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
+		case AXP20X_VBUC_CLIMIT_100mA:
+			val->intval = 100000;
+			break;
+		case AXP20X_VBUC_CLIMIT_500mA:
+			val->intval = 500000;
+			break;
+		case AXP20X_VBUC_CLIMIT_900mA:
+			val->intval = 900000;
+			break;
+		case AXP20X_VBUC_CLIMIT_NONE:
+			val->intval = -1;

drivers/power/axp20x_usb_power.c line 107

Quoted 10 lines

drivers/power/axp20x_usb_power.c new file +10 -0

+			break;
+		}
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		r = axp20x_read_variable_width(power->regmap,
+					       AXP20X_VBUS_I_ADC_H, 12);
+		if (r < 0)
+			return r;
+
+		val->intval = r * 375; /* 1 step = 0.375 mA */

And here too.

Quoted 64 lines

drivers/power/axp20x_usb_power.c new file +64 -0

+		return 0;
+	default:
+		break;
+	}
+
+	/* All the properties below need the input-status reg value */
+	r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
+	if (r)
+		return r;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+
+		r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
+		if (r)
+			return r;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+			break;
+		}
+
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property axp20x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static const struct power_supply_desc axp20x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp20x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
+static int axp20x_usb_power_probe(struct platform_device *pdev)
+{
+	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct axp20x_usb_power *power;

drivers/power/axp20x_usb_power.c line 177

Quoted 6 lines

drivers/power/axp20x_usb_power.c new file +6 -0

+	static const char * const irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	int i, irq, r;
+
+	if (!of_device_is_available(pdev->dev.of_node))
+		return -ENODEV;

That looks odd. Is it even going to be probed in the first place?

drivers/power/axp20x_usb_power.c line 183

Quoted 6 lines

drivers/power/axp20x_usb_power.c new file +6 -0

+
+	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	power->regmap = axp20x->regmap;

It should probably be wise to test that the axp20x pointer is not NULL.

Quoted 94 lines

drivers/power/axp20x_usb_power.c new file +60 -0

+
+	/* Enable vbus valid checking */
+	r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
+	if (r)
+		return r;
+
+	/* Enable vbus voltage and current measurement */
+	r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
+			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
+	if (r)
+		return r;
+
+	psy_cfg.of_node = pdev->dev.of_node;
+	psy_cfg.drv_data = power;
+
+	power->supply = devm_power_supply_register(&pdev->dev,
+					&axp20x_usb_power_desc, &psy_cfg);
+	if (IS_ERR(power->supply))
+		return PTR_ERR(power->supply);
+
+	/* Request irqs after registering, as irqs may trigger immediately */
+	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+		irq = platform_get_irq_byname(pdev, irq_names[i]);
+		if (irq < 0) {
+			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
+				 irq_names[i], irq);
+			continue;
+		}
+		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		r = devm_request_any_context_irq(&pdev->dev, irq,
+				axp20x_usb_power_irq, 0, DRVNAME, power);
+		if (r < 0)
+			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				 irq_names[i], r);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id axp20x_usb_power_match[] = {
+	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
+
+static struct platform_driver axp20x_usb_power_driver = {
+	.probe = axp20x_usb_power_probe,
+	.driver = {
+		.name = DRVNAME,
+		.of_match_table = axp20x_usb_power_match,
+	},
+};
+
+module_platform_driver(axp20x_usb_power_driver);
+
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
+MODULE_LICENSE("GPL");

include/linux/mfd/axp20x.h +19 -0

index 6d8b39a..8ec996e 100644
@@ -11,6 +11,8 @@
  #ifndef __LINUX_MFD_AXP20X_H
  #define __LINUX_MFD_AXP20X_H
 
+#include <linux/regmap.h>
+
  enum {
  	AXP202_ID = 0,
  	AXP209_ID,

@@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
  	struct gpio_desc *gpio_mux_cntl;
  };
 
+/* generic helper function for reading 9-16 bit wide regs */
+static inline int axp20x_read_variable_width(struct regmap *regmap,
+	unsigned int reg, unsigned int width)
+{
+	unsigned int reg_val, result;
+	int err;
+
+	err = regmap_read(regmap, reg, &reg_val);
+	if (err)
+		return err;
+
+	result = reg_val << (width - 8);
+
+	err = regmap_read(regmap, reg + 1, &reg_val);
+	if (err)
+		return err;
+

Quoted 8 lines

include/linux/mfd/axp20x.h +5 -1

+	result |= reg_val;
+
+	return result;
+}
+
  #endif /* __LINUX_MFD_AXP20X_H */
--

2.4.3

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Hi,

Quoted 8 lines · Hans de Goede

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Quoted 4 lines

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Once the other comments have been taken care of, the driver looks ok to me.

Hi,

Quoted 8 lines · Hans de Goede

This adds a driver for the usb power_supply bits of the axp20x PMICs.

I initially started writing my own driver, before coming aware of Bruno Pr?mont's excellent earlier RFC with a driver for this.

My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's drvier has, so I've copied the code for those from his driver.

Quoted 4 lines

Note that the AC-power-supply and battery charger bits will need separate drivers. Each one needs its own devictree child-node so that other devicetree nodes can reference the right power-supply, and thus each one will get its own mfd-cell / platform_device and platform-driver.

Once the other comments have been taken care of, the driver looks ok to me.

Hi,

Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt line 31

Quoted 7 lines · Hans de Goede

Add binding documentation for the usb power supply part of the AXP20x pmic. [...]

Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt new file +4 -0

+Example:
+
[...]
+
+	usb_power_supply: usb_power_supply {

^^^^^^^^^^^^^^^^
use usb-power-supply here.