Skip to contentSkip to conversation

4.0.9-stable review

PATCH In review Greg Kroah-Hartman 5 participants 63 messages Jul 19, 2015 – Jul 20, 2015 Stable branch

lore
Share & tools
lore

Greg Kroah-Hartman

author maintainer
#0 lore raw

cover 4.0.9-stable review

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.0.9-rc1.gz

and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 4.0.9-rc1

Frodo Lai <[email protected]>
Input: pixcir_i2c_ts - fix receive error

Zhichang Yuan <[email protected]>
of/pci: Fix pci_address_to_pio() conversion of CPU address to I/O port

Alex Williamson <[email protected]>
PCI: pciehp: Wait for hotplug command completion where necessary

Yinghai Lu <[email protected]>
PCI: Add pci_bus_addr_t

Rafael J. Wysocki <[email protected]>
PCI: Propagate the "ignore hotplug" setting to parent

Uwe Kleine-König <[email protected]>
mtd: dc21285: use raw spinlock functions for nw_gpio_lock

Brian Norris <[email protected]>

    mtd: fix: avoid race condition when accessing mtd->usecount

Grygorii Strashko <[email protected]>
leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger

Liu Ying <[email protected]>
video: mxsfb: Make sure axi clock is enabled when accessing registers

Axel Lin <[email protected]>
genirq: devres: Fix testing return value of request_any_context_irq()

Bart Van Assche <[email protected]>
IB/srp: Fix reconnection failure handling

Bart Van Assche <[email protected]>
IB/srp: Fix connection state tracking

Bart Van Assche <[email protected]>
IB/srp: Fix a connection setup race

Bart Van Assche <[email protected]>
IB/srp: Remove an extraneous scsi_host_put() from an error path

Bart Van Assche <[email protected]>
scsi_transport_srp: Fix a race condition

Bart Van Assche <[email protected]>
scsi_transport_srp: Introduce srp_wait_for_queuecommand()

Ezequiel Garcia <[email protected]>
spi: pl022: Specify 'num-cs' property as required in devicetree binding

Gregory CLEMENT <[email protected]>
spi: orion: Fix maximum baud rates for Armada 370/XP

Martin Sperl <[email protected]>
spi: fix race freeing dummy_tx/rx before it is unmapped

Miroslav Benes <[email protected]>
livepatch: add module locking around kallsyms calls

Stefan Wahren <[email protected]>
regulator: core: fix constraints output buffer

Joe Perches <[email protected]>
regulator: max77686: fix gpio_enabled shift wrapping bug

Maxime Coquelin <[email protected]>
regmap: Fix possible shift overflow in regmap_field_init()

Arun Chandran <[email protected]>
regmap: Fix regmap_bulk_read in BE mode

Sagi Grimberg <[email protected]>
iser-target: release stale iser connections

Vlastimil Babka <[email protected]>
mm, thp: respect MPOL_PREFERRED policy with non-local node

Larry Finger <[email protected]>
mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()

Catalin Marinas <[email protected]>
mm: kmemleak: allow safe memory scanning during kmemleak disabling

Will Deacon <[email protected]>
arm64: vdso: work-around broken ELF toolchains in Makefile

Dave P Martin <[email protected]>
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP

Mark Rutland <[email protected]>
arm64: entry: fix context tracking for el0_sp_pc

Catalin Marinas <[email protected]>
arm64: Do not attempt to use init_mm in reset_context()

Tomas Winkler <[email protected]>
mei: txe: reduce suspend/resume time

Alexander Usyskin <[email protected]>
mei: me: wait for power gating exit confirmation

Vineet Gupta <[email protected]>
ARC: add compiler barrier to LLSC based cmpxchg

Vineet Gupta <[email protected]>
ARC: add smp barriers around atomics per Documentation/atomic_ops.txt

Arnaldo Carvalho de Melo <[email protected]>
tools selftests: Fix 'clean' target with make 3.81

Antonio Ospite <[email protected]>

    iio: accel: kxcjk-1013: add the "KXCJ9000" ACPI id

Rafael J. Wysocki <[email protected]>
ACPI / PM: Add missing pm_generic_complete() invocation

Rafael J. Wysocki <[email protected]>
ACPI / init: Switch over platform to the ACPI mode later

Takashi Iwai <[email protected]>
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780

Takashi Iwai <[email protected]>
ALSA: hda - Add headset support to Acer Aspire V5

Alex Deucher <[email protected]>
ALSA: hda - set proper caps for newer AMD hda audio in KB/KV

David Henningsson <[email protected]>
ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out

Takashi Iwai <[email protected]>
ALSA: pcm: Fix pcm_class sysfs output

Ryan Underwood <[email protected]>
Disable write buffering on Toshiba ToPIC95

Brian King <[email protected]>
ipr: Increase default adapter init stage change timeout

Paul E. McKenney <[email protected]>
rcu: Correctly handle non-empty Tiny RCU callback list with none ready

Aaron Lu <[email protected]>
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip

Eric W. Biederman <[email protected]>
sysfs: Create mountpoints with sysfs_create_mount_point

Eric W. Biederman <[email protected]>
mnt: Modify fs_fully_visible to deal with locked ro nodev and atime

Eric W. Biederman <[email protected]>
mnt: Refactor the logic for mounting sysfs and proc in a user namespace

Eric W. Biederman <[email protected]>
mnt: Update fs_fully_visible to test for permanently empty directories

Eric W. Biederman <[email protected]>
sysfs: Add support for permanently empty directories to serve as mount points.

Eric W. Biederman <[email protected]>
kernfs: Add support for always empty directories.

Eric W. Biederman <[email protected]>
proc: Allow creating permanently empty directories that serve as mount points

Eric W. Biederman <[email protected]>
sysctl: Allow creating permanently empty directories that serve as mountpoints.

Eric W. Biederman <[email protected]>
fs: Add helper functions for permanently empty directories.

-------------

Diffstat:

 Documentation/DMA-API-HOWTO.txt                    | 29 ++++---
 Documentation/DMA-API.txt                          | 30 +++----
 .../devicetree/bindings/spi/spi_pl022.txt          |  2 +-
 Makefile                                           |  4 +-
 arch/arc/include/asm/atomic.h                      | 21 +++++
 arch/arc/include/asm/bitops.h                      | 19 +++++
 arch/arc/include/asm/cmpxchg.h                     | 26 +++++-
 arch/arc/include/asm/spinlock.h                    | 32 ++++++++
 arch/arm64/kernel/entry.S                          |  1 +
 arch/arm64/kernel/vdso/Makefile                    |  4 +
 arch/arm64/mm/context.c                            |  8 ++
 arch/arm64/mm/init.c                               |  2 +-
 arch/s390/hypfs/inode.c                            | 12 +--
 drivers/acpi/bus.c                                 | 56 +++++++++----
 drivers/acpi/device_pm.c                           |  1 +
 drivers/base/regmap/regmap.c                       |  5 +-
 drivers/firmware/efi/efi.c                         |  6 +-
 drivers/gpio/gpio-crystalcove.c                    |  1 +
 drivers/iio/accel/kxcjk-1013.c                     |  1 +
 drivers/infiniband/ulp/isert/ib_isert.c            | 18 +++-
 drivers/infiniband/ulp/srp/ib_srp.c                | 83 +++++++++----------
 drivers/infiniband/ulp/srp/ib_srp.h                |  2 +-
 drivers/input/touchscreen/pixcir_i2c_ts.c          |  2 +-
 drivers/leds/led-class.c                           |  7 +-
 drivers/misc/mei/client.c                          |  2 +-
 drivers/misc/mei/hw-me.c                           | 59 ++++++++++++-
 drivers/misc/mei/hw-txe.c                          | 33 +++++---
 drivers/misc/mei/mei_dev.h                         | 11 +++
 drivers/mtd/maps/dc21285.c                         |  4 +-
 drivers/mtd/mtd_blkdevs.c                          |  5 ++
 drivers/of/address.c                               |  2 +-
 drivers/pci/Kconfig                                |  4 +
 drivers/pci/bus.c                                  | 10 +--
 drivers/pci/hotplug/pciehp_hpc.c                   | 52 ++++++++----
 drivers/pci/pci.c                                  | 11 +++
 drivers/pci/probe.c                                | 12 +--
 drivers/pcmcia/topic.h                             | 16 ++++
 drivers/regulator/core.c                           |  2 +-
 drivers/regulator/max77686.c                       |  6 +-
 drivers/scsi/ipr.h                                 |  2 +-
 drivers/scsi/scsi_transport_srp.c                  | 58 +++++++------
 drivers/spi/spi-orion.c                            | 25 +++++-
 drivers/spi/spi.c                                  | 11 +--
 drivers/video/fbdev/mxsfb.c                        | 68 +++++++++++----
 fs/configfs/mount.c                                | 10 +--
 fs/debugfs/inode.c                                 | 11 +--
 fs/fuse/inode.c                                    |  9 +-
 fs/kernfs/dir.c                                    | 38 ++++++++-
 fs/kernfs/inode.c                                  |  2 +
 fs/libfs.c                                         | 96 ++++++++++++++++++++++
 fs/namespace.c                                     | 31 ++++++-
 fs/proc/generic.c                                  | 23 ++++++
 fs/proc/inode.c                                    |  4 +
 fs/proc/internal.h                                 |  6 ++
 fs/proc/proc_sysctl.c                              | 37 +++++++++
 fs/proc/root.c                                     |  9 +-
 fs/pstore/inode.c                                  | 12 +--
 fs/sysfs/dir.c                                     | 34 ++++++++
 fs/sysfs/mount.c                                   |  5 +-
 include/linux/acpi.h                               |  2 +
 include/linux/fs.h                                 |  4 +-
 include/linux/kernfs.h                             |  3 +
 include/linux/kmemleak.h                           |  6 +-
 include/linux/pci.h                                | 18 ++--
 include/linux/sysctl.h                             |  3 +
 include/linux/sysfs.h                              | 15 ++++
 include/linux/types.h                              | 12 ++-
 init/main.c                                        |  1 +
 kernel/cgroup.c                                    | 10 +--
 kernel/irq/devres.c                                |  4 +-
 kernel/livepatch/core.c                            | 18 ++--
 kernel/rcu/tiny.c                                  |  5 ++
 kernel/sysctl.c                                    |  8 +-
 mm/kmemleak.c                                      | 28 +++++--
 mm/mempolicy.c                                     | 38 +++++----
 mm/percpu.c                                        |  2 +-
 security/inode.c                                   | 10 +--
 security/selinux/selinuxfs.c                       | 11 ++-
 security/smack/smackfs.c                           |  8 +-
 sound/core/pcm.c                                   |  6 +-
 sound/pci/hda/hda_intel.c                          |  4 +
 sound/pci/hda/patch_realtek.c                      | 25 ++++++
 tools/testing/selftests/Makefile                   |  2 +-
 83 files changed, 1006 insertions(+), 329 deletions(-)
author maintainer
#1 lore raw

PATCH 1/58 fs: Add helper functions for permanently empty directories.

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit fbabfd0f4ee2e8847bf56edf481249ad1bb8c44d upstream.

To ensure it is safe to mount proc and sysfs I need to check if filesystems that are mounted on top of them are mounted on truly empty directories. Given that some directories can gain entries over time, knowing that a directory is empty right now is insufficient.

Therefore add supporting infrastructure for permantently empty directories that proc and sysfs can use when they create mount points for filesystems and fs_fully_visible can use to test for permanently empty directories to ensure that nothing will be gained by mounting a fresh copy of proc or sysfs.

---
 fs/libfs.c         |   96 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/fs.h |    2 +
 2 files changed, 98 insertions(+)
fs/libfs.c +96 -0
@@ -1093,3 +1093,99 @@ simple_nosetlease(struct file *filp, lon
 	return -EINVAL;
 }
 EXPORT_SYMBOL(simple_nosetlease);
+
+
+/*
+ * Operations for a permanently empty directory.
+ */
+static struct dentry *empty_dir_lookup(struct inode *dir, struct dentry *dentry, unsigned int flags)
+{
+	return ERR_PTR(-ENOENT);
+}
+
+static int empty_dir_getattr(struct vfsmount *mnt, struct dentry *dentry,
+				 struct kstat *stat)
+{
+	struct inode *inode = d_inode(dentry);
+	generic_fillattr(inode, stat);
+	return 0;
+}
+
+static int empty_dir_setattr(struct dentry *dentry, struct iattr *attr)
+{
+	return -EPERM;
+}
+
+static int empty_dir_setxattr(struct dentry *dentry, const char *name,
+			      const void *value, size_t size, int flags)
+{
+	return -EOPNOTSUPP;
+}
+
+static ssize_t empty_dir_getxattr(struct dentry *dentry, const char *name,
+				  void *value, size_t size)
+{
+	return -EOPNOTSUPP;
+}
+
+static int empty_dir_removexattr(struct dentry *dentry, const char *name)
+{
+	return -EOPNOTSUPP;
+}
+
+static ssize_t empty_dir_listxattr(struct dentry *dentry, char *list, size_t size)
+{
+	return -EOPNOTSUPP;
+}
+
+static const struct inode_operations empty_dir_inode_operations = {
+	.lookup		= empty_dir_lookup,
+	.permission	= generic_permission,
+	.setattr	= empty_dir_setattr,
+	.getattr	= empty_dir_getattr,
+	.setxattr	= empty_dir_setxattr,
+	.getxattr	= empty_dir_getxattr,
+	.removexattr	= empty_dir_removexattr,
+	.listxattr	= empty_dir_listxattr,
+};
+
+static loff_t empty_dir_llseek(struct file *file, loff_t offset, int whence)
+{
+	/* An empty directory has two entries . and .. at offsets 0 and 1 */
+	return generic_file_llseek_size(file, offset, whence, 2, 2);
+}
+
+static int empty_dir_readdir(struct file *file, struct dir_context *ctx)
+{
+	dir_emit_dots(file, ctx);
+	return 0;
+}
+
+static const struct file_operations empty_dir_operations = {
+	.llseek		= empty_dir_llseek,
+	.read		= generic_read_dir,
+	.iterate	= empty_dir_readdir,
+	.fsync		= noop_fsync,
+};
+
+
+void make_empty_dir_inode(struct inode *inode)
+{
+	set_nlink(inode, 2);
+	inode->i_mode = S_IFDIR | S_IRUGO | S_IXUGO;
+	inode->i_uid = GLOBAL_ROOT_UID;
+	inode->i_gid = GLOBAL_ROOT_GID;
+	inode->i_rdev = 0;
+	inode->i_size = 2;
+	inode->i_blkbits = PAGE_SHIFT;
+	inode->i_blocks = 0;
+
+	inode->i_op = &empty_dir_inode_operations;
+	inode->i_fop = &empty_dir_operations;
+}
+
+bool is_empty_dir_inode(struct inode *inode)
+{
+	return (inode->i_fop == &empty_dir_operations) &&
+		(inode->i_op == &empty_dir_inode_operations);
+}
include/linux/fs.h +2 -0
@@ -2721,6 +2721,8 @@ extern struct dentry *simple_lookup(stru
 extern ssize_t generic_read_dir(struct file *, char __user *, size_t, loff_t *);
 extern const struct file_operations simple_dir_operations;
 extern const struct inode_operations simple_dir_inode_operations;
+extern void make_empty_dir_inode(struct inode *inode);
+extern bool is_empty_dir_inode(struct inode *inode);
 struct tree_descr { char *name; const struct file_operations *ops; int mode; };
 struct dentry *d_alloc_name(struct dentry *, const char *);
 extern int simple_fill_super(struct super_block *, unsigned long, struct tree_descr *);
author maintainer
#2 lore raw

PATCH 2/58 sysctl: Allow creating permanently empty directories that serve as mountpoints.

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit f9bd6733d3f11e24f3949becf277507d422ee1eb upstream.

Add a magic sysctl table sysctl_mount_point that when used to create a directory forces that directory to be permanently empty.

Update the code to use make_empty_dir_inode when accessing permanently empty directories.

Update the code to not allow adding to permanently empty directories.

Update /proc/sys/fs/binfmt_misc to be a permanently empty directory.

---
 fs/proc/proc_sysctl.c  |   37 +++++++++++++++++++++++++++++++++++++
 include/linux/sysctl.h |    3 +++
 kernel/sysctl.c        |    8 +-------
 3 files changed, 41 insertions(+), 7 deletions(-)
fs/proc/proc_sysctl.c +37 -0
@@ -19,6 +19,28 @@ static const struct inode_operations pro
 static const struct file_operations proc_sys_dir_file_operations;
 static const struct inode_operations proc_sys_dir_operations;
 
+/* Support for permanently empty directories */
+
+struct ctl_table sysctl_mount_point[] = {
+	{ }
+};
+
+static bool is_empty_dir(struct ctl_table_header *head)
+{
+	return head->ctl_table[0].child == sysctl_mount_point;
+}
+
+static void set_empty_dir(struct ctl_dir *dir)
+{
+	dir->header.ctl_table[0].child = sysctl_mount_point;
+}
+
+static void clear_empty_dir(struct ctl_dir *dir)
+
+{
+	dir->header.ctl_table[0].child = NULL;
+}
+
 void proc_sys_poll_notify(struct ctl_table_poll *poll)
 {
 	if (!poll)
@@ -187,6 +209,17 @@ static int insert_header(struct ctl_dir
 	struct ctl_table *entry;
 	int err;
 
+	/* Is this a permanently empty directory? */
+	if (is_empty_dir(&dir->header))
+		return -EROFS;
+
+	/* Am I creating a permanently empty directory? */
+	if (header->ctl_table == sysctl_mount_point) {
+		if (!RB_EMPTY_ROOT(&dir->root))
+			return -EINVAL;
+		set_empty_dir(dir);
+	}
+
 	dir->header.nreg++;
 	header->parent = dir;
 	err = insert_links(header);
@@ -202,6 +235,8 @@ fail:
 	erase_header(header);
 	put_links(header);
 fail_links:
+	if (header->ctl_table == sysctl_mount_point)
+		clear_empty_dir(dir);
 	header->parent = NULL;
 	drop_sysctl_table(&dir->header);
 	return err;
@@ -419,6 +454,8 @@ static struct inode *proc_sys_make_inode
 		inode->i_mode |= S_IFDIR;
 		inode->i_op = &proc_sys_dir_operations;
 		inode->i_fop = &proc_sys_dir_file_operations;
+		if (is_empty_dir(head))
+			make_empty_dir_inode(inode);
 	}
 out:
 	return inode;
include/linux/sysctl.h +3 -0
@@ -188,6 +188,9 @@ struct ctl_table_header *register_sysctl
 void unregister_sysctl_table(struct ctl_table_header * table);
 
 extern int sysctl_init(void);
+
+extern struct ctl_table sysctl_mount_point[];
+
 #else /* CONFIG_SYSCTL */
 static inline struct ctl_table_header *register_sysctl_table(struct ctl_table * table)
 {
kernel/sysctl.c +1 -7
@@ -1510,12 +1510,6 @@ static struct ctl_table vm_table[] = {
 	{ }
 };
 
-#if defined(CONFIG_BINFMT_MISC) || defined(CONFIG_BINFMT_MISC_MODULE)
-static struct ctl_table binfmt_misc_table[] = {
-	{ }
-};
-#endif
-
 static struct ctl_table fs_table[] = {
 	{
 		.procname	= "inode-nr",
@@ -1669,7 +1663,7 @@ static struct ctl_table fs_table[] = {
 	{
 		.procname	= "binfmt_misc",
 		.mode		= 0555,
-		.child		= binfmt_misc_table,
+		.child		= sysctl_mount_point,
 	},
 #endif
 	{
author maintainer
#3 lore raw

PATCH 3/58 proc: Allow creating permanently empty directories that serve as mount points

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit eb6d38d5427b3ad42f5268da0f1dd31bb0af1264 upstream.

Add a new function proc_create_mount_point that when used to creates a directory that can not be added to.

Add a new function is_empty_pde to test if a function is a mount point.

Update the code to use make_empty_dir_inode when reporting a permanently empty directory to the vfs.

Update the code to not allow adding to permanently empty directories.

Update /proc/openprom and /proc/fs/nfsd to be permanently empty directories.

---
 fs/proc/generic.c  |   23 +++++++++++++++++++++++
 fs/proc/inode.c    |    4 ++++
 fs/proc/internal.h |    6 ++++++
 fs/proc/root.c     |    4 ++--
 4 files changed, 35 insertions(+), 2 deletions(-)
fs/proc/generic.c +23 -0
@@ -373,6 +373,10 @@ static struct proc_dir_entry *__proc_cre
 		WARN(1, "create '/proc/%s' by hand\n", qstr.name);
 		return NULL;
 	}
+	if (is_empty_pde(*parent)) {
+		WARN(1, "attempt to add to permanently empty directory");
+		return NULL;
+	}
 
 	ent = kzalloc(sizeof(struct proc_dir_entry) + qstr.len + 1, GFP_KERNEL);
 	if (!ent)
@@ -455,6 +459,25 @@ struct proc_dir_entry *proc_mkdir(const
 }
 EXPORT_SYMBOL(proc_mkdir);
 
+struct proc_dir_entry *proc_create_mount_point(const char *name)
+{
+	umode_t mode = S_IFDIR | S_IRUGO | S_IXUGO;
+	struct proc_dir_entry *ent, *parent = NULL;
+
+	ent = __proc_create(&parent, name, mode, 2);
+	if (ent) {
+		ent->data = NULL;
+		ent->proc_fops = NULL;
+		ent->proc_iops = NULL;
+		if (proc_register(parent, ent) < 0) {
+			kfree(ent);
+			parent->nlink--;
+			ent = NULL;
+		}
+	}
+	return ent;
+}
+
 struct proc_dir_entry *proc_create_data(const char *name, umode_t mode,
 					struct proc_dir_entry *parent,
 					const struct file_operations *proc_fops,
fs/proc/inode.c +4 -0
@@ -423,6 +423,10 @@ struct inode *proc_get_inode(struct supe
 		inode->i_mtime = inode->i_atime = inode->i_ctime = CURRENT_TIME;
 		PROC_I(inode)->pde = de;
 
+		if (is_empty_pde(de)) {
+			make_empty_dir_inode(inode);
+			return inode;
+		}
 		if (de->mode) {
 			inode->i_mode = de->mode;
 			inode->i_uid = de->uid;
fs/proc/internal.h +6 -0
@@ -191,6 +191,12 @@ static inline struct proc_dir_entry *pde
 }
 extern void pde_put(struct proc_dir_entry *);
 
+static inline bool is_empty_pde(const struct proc_dir_entry *pde)
+{
+	return S_ISDIR(pde->mode) && !pde->proc_iops;
+}
+struct proc_dir_entry *proc_create_mount_point(const char *name);
+
 /*
  * inode.c
  */
fs/proc/root.c +2 -2
@@ -182,10 +182,10 @@ void __init proc_root_init(void)
 #endif
 	proc_mkdir("fs", NULL);
 	proc_mkdir("driver", NULL);
-	proc_mkdir("fs/nfsd", NULL); /* somewhere for the nfsd filesystem to be mounted */
+	proc_create_mount_point("fs/nfsd"); /* somewhere for the nfsd filesystem to be mounted */
 #if defined(CONFIG_SUN_OPENPROMFS) || defined(CONFIG_SUN_OPENPROMFS_MODULE)
 	/* just give it a mountpoint */
-	proc_mkdir("openprom", NULL);
+	proc_create_mount_point("openprom");
 #endif
 	proc_tty_init();
 	proc_mkdir("bus", NULL);
author maintainer
#4 lore raw

PATCH 4/58 kernfs: Add support for always empty directories.

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit ea015218f2f7ace2dad9cedd21ed95bdba2886d7 upstream.

Add a new function kernfs_create_empty_dir that can be used to create directory that can not be modified.

Update the code to use make_empty_dir_inode when reporting a permanently empty directory to the vfs.

Update the code to not allow adding to permanently empty directories.

---
 fs/kernfs/dir.c        |   38 +++++++++++++++++++++++++++++++++++++-
 fs/kernfs/inode.c      |    2 ++
 include/linux/kernfs.h |    3 +++
 3 files changed, 42 insertions(+), 1 deletion(-)
fs/kernfs/dir.c +37 -1
@@ -592,6 +592,9 @@ int kernfs_add_one(struct kernfs_node *k
 		goto out_unlock;
 
 	ret = -ENOENT;
+	if (parent->flags & KERNFS_EMPTY_DIR)
+		goto out_unlock;
+
 	if ((parent->flags & KERNFS_ACTIVATED) && !kernfs_active(parent))
 		goto out_unlock;
 
@@ -783,6 +786,38 @@ struct kernfs_node *kernfs_create_dir_ns
 	return ERR_PTR(rc);
 }
 
+/**
+ * kernfs_create_empty_dir - create an always empty directory
+ * @parent: parent in which to create a new directory
+ * @name: name of the new directory
+ *
+ * Returns the created node on success, ERR_PTR() value on failure.
+ */
+struct kernfs_node *kernfs_create_empty_dir(struct kernfs_node *parent,
+					    const char *name)
+{
+	struct kernfs_node *kn;
+	int rc;
+
+	/* allocate */
+	kn = kernfs_new_node(parent, name, S_IRUGO|S_IXUGO|S_IFDIR, KERNFS_DIR);
+	if (!kn)
+		return ERR_PTR(-ENOMEM);
+
+	kn->flags |= KERNFS_EMPTY_DIR;
+	kn->dir.root = parent->dir.root;
+	kn->ns = NULL;
+	kn->priv = NULL;
+
+	/* link in */
+	rc = kernfs_add_one(kn);
+	if (!rc)
+		return kn;
+
+	kernfs_put(kn);
+	return ERR_PTR(rc);
+}
+
 static struct dentry *kernfs_iop_lookup(struct inode *dir,
 					struct dentry *dentry,
 					unsigned int flags)
@@ -1254,7 +1289,8 @@ int kernfs_rename_ns(struct kernfs_node
 	mutex_lock(&kernfs_mutex);
 
 	error = -ENOENT;
-	if (!kernfs_active(kn) || !kernfs_active(new_parent))
+	if (!kernfs_active(kn) || !kernfs_active(new_parent) ||
+	    (new_parent->flags & KERNFS_EMPTY_DIR))
 		goto out;
 
 	error = 0;
fs/kernfs/inode.c +2 -0
@@ -296,6 +296,8 @@ static void kernfs_init_inode(struct ker
 	case KERNFS_DIR:
 		inode->i_op = &kernfs_dir_iops;
 		inode->i_fop = &kernfs_dir_fops;
+		if (kn->flags & KERNFS_EMPTY_DIR)
+			make_empty_dir_inode(inode);
 		break;
 	case KERNFS_FILE:
 		inode->i_size = kn->attr.size;
include/linux/kernfs.h +3 -0
@@ -45,6 +45,7 @@ enum kernfs_node_flag {
 	KERNFS_LOCKDEP		= 0x0100,
 	KERNFS_SUICIDAL		= 0x0400,
 	KERNFS_SUICIDED		= 0x0800,
+	KERNFS_EMPTY_DIR	= 0x1000,
 };
 
 /* @flags for kernfs_create_root() */
@@ -285,6 +286,8 @@ void kernfs_destroy_root(struct kernfs_r
 struct kernfs_node *kernfs_create_dir_ns(struct kernfs_node *parent,
 					 const char *name, umode_t mode,
 					 void *priv, const void *ns);
+struct kernfs_node *kernfs_create_empty_dir(struct kernfs_node *parent,
+					    const char *name);
 struct kernfs_node *__kernfs_create_file(struct kernfs_node *parent,
 					 const char *name,
 					 umode_t mode, loff_t size,
author maintainer
#5 lore raw

PATCH 5/58 sysfs: Add support for permanently empty directories to serve as mount points.

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit 87d2846fcf88113fae2341da1ca9a71f0d916f2c upstream.

Add two functions sysfs_create_mount_point and sysfs_remove_mount_point that hang a permanently empty directory off of a kobject or remove a permanently emptpy directory hanging from a kobject. Export these new functions so modular filesystems can use them.

---
 fs/sysfs/dir.c        |   34 ++++++++++++++++++++++++++++++++++
 include/linux/sysfs.h |   15 +++++++++++++++
 2 files changed, 49 insertions(+)
fs/sysfs/dir.c +34 -0
@@ -121,3 +121,37 @@ int sysfs_move_dir_ns(struct kobject *ko
 
 	return kernfs_rename_ns(kn, new_parent, kn->name, new_ns);
 }
+
+/**
+ * sysfs_create_mount_point - create an always empty directory
+ * @parent_kobj:  kobject that will contain this always empty directory
+ * @name: The name of the always empty directory to add
+ */
+int sysfs_create_mount_point(struct kobject *parent_kobj, const char *name)
+{
+	struct kernfs_node *kn, *parent = parent_kobj->sd;
+
+	kn = kernfs_create_empty_dir(parent, name);
+	if (IS_ERR(kn)) {
+		if (PTR_ERR(kn) == -EEXIST)
+			sysfs_warn_dup(parent, name);
+		return PTR_ERR(kn);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(sysfs_create_mount_point);
+
+/**
+ *	sysfs_remove_mount_point - remove an always empty directory.
+ *	@parent_kobj: kobject that will contain this always empty directory
+ *	@name: The name of the always empty directory to remove
+ *
+ */
+void sysfs_remove_mount_point(struct kobject *parent_kobj, const char *name)
+{
+	struct kernfs_node *parent = parent_kobj->sd;
+
+	kernfs_remove_by_name_ns(parent, name, NULL);
+}
+EXPORT_SYMBOL_GPL(sysfs_remove_mount_point);
include/linux/sysfs.h +15 -0
@@ -195,6 +195,10 @@ int __must_check sysfs_rename_dir_ns(str
 int __must_check sysfs_move_dir_ns(struct kobject *kobj,
 				   struct kobject *new_parent_kobj,
 				   const void *new_ns);
+int __must_check sysfs_create_mount_point(struct kobject *parent_kobj,
+					  const char *name);
+void sysfs_remove_mount_point(struct kobject *parent_kobj,
+			      const char *name);
 
 int __must_check sysfs_create_file_ns(struct kobject *kobj,
 				      const struct attribute *attr,
@@ -283,6 +287,17 @@ static inline int sysfs_move_dir_ns(stru
 	return 0;
 }
 
+static inline int sysfs_create_mount_point(struct kobject *parent_kobj,
+					   const char *name)
+{
+	return 0;
+}
+
+static inline void sysfs_remove_mount_point(struct kobject *parent_kobj,
+					    const char *name)
+{
+}
+
 static inline int sysfs_create_file_ns(struct kobject *kobj,
 				       const struct attribute *attr,
 				       const void *ns)
author maintainer
#6 lore raw

PATCH 6/58 mnt: Update fs_fully_visible to test for permanently empty directories

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit 7236c85e1be51a9e25ba0f6e087a66ca89605a49 upstream.

fs_fully_visible attempts to make fresh mounts of proc and sysfs give the mounter no more access to proc and sysfs than if they could have by creating a bind mount. One aspect of proc and sysfs that makes this particularly tricky is that there are other filesystems that typically mount on top of proc and sysfs. As those filesystems are mounted on empty directories in practice it is safe to ignore them. However testing to ensure filesystems are mounted on empty directories has not been something the in kernel data structures have supported so the current test for an empty directory which checks to see if nlink <= 2 is a bit lacking.

proc and sysfs have recently been modified to use the new empty_dir infrastructure to create all of their dedicated mount points. Instead of testing for S_ISDIR(inode->i_mode) && i_nlink <= 2 to see if a directory is empty, test for is_empty_dir_inode(inode). That small change guaranteess mounts found on proc and sysfs really are safe to ignore, because the directories are not only empty but nothing can ever be added to them. This guarantees there is nothing to worry about when mounting proc and sysfs.

---
 fs/namespace.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
fs/namespace.c +2 -3
@@ -3196,9 +3196,8 @@ bool fs_fully_visible(struct file_system
 			/* Only worry about locked mounts */
 			if (!(mnt->mnt.mnt_flags & MNT_LOCKED))
 				continue;
-			if (!S_ISDIR(inode->i_mode))
-				goto next;
-			if (inode->i_nlink > 2)
+			/* Is the directory permanetly empty? */
+			if (!is_empty_dir_inode(inode))
 				goto next;
 		}
 		visible = true;
author maintainer
#7 lore raw

PATCH 7/58 mnt: Refactor the logic for mounting sysfs and proc in a user namespace

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit 1b852bceb0d111e510d1a15826ecc4a19358d512 upstream.

Fresh mounts of proc and sysfs are a very special case that works very much like a bind mount. Unfortunately the current structure can not preserve the MNT_LOCK... mount flags. Therefore refactor the logic into a form that can be modified to preserve those lock bits.

Add a new filesystem flag FS_USERNS_VISIBLE that requires some mount of the filesystem be fully visible in the current mount namespace, before the filesystem may be mounted.

Move the logic for calling fs_fully_visible from proc and sysfs into fs/namespace.c where it has greater access to mount namespace state.

---
 fs/namespace.c     |    8 +++++++-
 fs/proc/root.c     |    5 +----
 fs/sysfs/mount.c   |    5 +----
 include/linux/fs.h |    2 +-
 4 files changed, 10 insertions(+), 10 deletions(-)
fs/namespace.c +7 -1
@@ -2334,6 +2334,8 @@ unlock:
 	return err;
 }
 
+static bool fs_fully_visible(struct file_system_type *fs_type);
+
 /*
  * create a new mount for userspace and request it to be added into the
  * namespace's tree
@@ -2365,6 +2367,10 @@ static int do_new_mount(struct path *pat
 			flags |= MS_NODEV;
 			mnt_flags |= MNT_NODEV | MNT_LOCK_NODEV;
 		}
+		if (type->fs_flags & FS_USERNS_VISIBLE) {
+			if (!fs_fully_visible(type))
+				return -EPERM;
+		}
 	}
 
 	mnt = vfs_kern_mount(type, flags, name, data);
@@ -3166,7 +3172,7 @@ bool current_chrooted(void)
 	return chrooted;
 }
 
-bool fs_fully_visible(struct file_system_type *type)
+static bool fs_fully_visible(struct file_system_type *type)
 {
 	struct mnt_namespace *ns = current->nsproxy->mnt_ns;
 	struct mount *mnt;
fs/proc/root.c +1 -4
@@ -112,9 +112,6 @@ static struct dentry *proc_mount(struct
 		ns = task_active_pid_ns(current);
 		options = data;
 
-		if (!capable(CAP_SYS_ADMIN) && !fs_fully_visible(fs_type))
-			return ERR_PTR(-EPERM);
-
 		/* Does the mounter have privilege over the pid namespace? */
 		if (!ns_capable(ns->user_ns, CAP_SYS_ADMIN))
 			return ERR_PTR(-EPERM);
@@ -159,7 +156,7 @@ static struct file_system_type proc_fs_t
 	.name		= "proc",
 	.mount		= proc_mount,
 	.kill_sb	= proc_kill_sb,
-	.fs_flags	= FS_USERNS_MOUNT,
+	.fs_flags	= FS_USERNS_VISIBLE | FS_USERNS_MOUNT,
 };
 
 void __init proc_root_init(void)
fs/sysfs/mount.c +1 -4
@@ -31,9 +31,6 @@ static struct dentry *sysfs_mount(struct
 	bool new_sb;
 
 	if (!(flags & MS_KERNMOUNT)) {
-		if (!capable(CAP_SYS_ADMIN) && !fs_fully_visible(fs_type))
-			return ERR_PTR(-EPERM);
-
 		if (!kobj_ns_current_may_mount(KOBJ_NS_TYPE_NET))
 			return ERR_PTR(-EPERM);
 	}
@@ -58,7 +55,7 @@ static struct file_system_type sysfs_fs_
 	.name		= "sysfs",
 	.mount		= sysfs_mount,
 	.kill_sb	= sysfs_kill_sb,
-	.fs_flags	= FS_USERNS_MOUNT,
+	.fs_flags	= FS_USERNS_VISIBLE | FS_USERNS_MOUNT,
 };
 
 int __init sysfs_init(void)
include/linux/fs.h +1 -1
@@ -1863,6 +1863,7 @@ struct file_system_type {
 #define FS_HAS_SUBTYPE		4
 #define FS_USERNS_MOUNT		8	/* Can be mounted by userns root */
 #define FS_USERNS_DEV_MOUNT	16 /* A userns mount does not imply MNT_NODEV */
+#define FS_USERNS_VISIBLE	32	/* FS must already be visible */
 #define FS_RENAME_DOES_D_MOVE	32768	/* FS will handle d_move() during rename() internally. */
 	struct dentry *(*mount) (struct file_system_type *, int,
 		       const char *, void *);
@@ -1950,7 +1951,6 @@ extern int vfs_ustat(dev_t, struct kstat
 extern int freeze_super(struct super_block *super);
 extern int thaw_super(struct super_block *super);
 extern bool our_mnt(struct vfsmount *mnt);
-extern bool fs_fully_visible(struct file_system_type *);
 
 extern int current_umask(void);
 
author maintainer
#8 lore raw

PATCH 8/58 mnt: Modify fs_fully_visible to deal with locked ro nodev and atime

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit 8c6cf9cc829fcd0b179b59f7fe288941d0e31108 upstream.

Ignore an existing mount if the locked readonly, nodev or atime attributes are less permissive than the desired attributes of the new mount.

On success ensure the new mount locks all of the same readonly, nodev and atime attributes as the old mount.

The nosuid and noexec attributes are not checked here as this change is destined for stable and enforcing those attributes causes a regression in lxc and libvirt-lxc where those applications will not start and there are no known executables on sysfs or proc and no known way to create exectuables without code modifications

Fixes e51db73532955 ("userns: Better restrictions on when proc and sysfs can be mounted")
---
 fs/namespace.c |   24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
fs/namespace.c +21 -3
@@ -2334,7 +2334,7 @@ unlock:
 	return err;
 }
 
-static bool fs_fully_visible(struct file_system_type *fs_type);
+static bool fs_fully_visible(struct file_system_type *fs_type, int *new_mnt_flags);
 
 /*
  * create a new mount for userspace and request it to be added into the
@@ -2368,7 +2368,7 @@ static int do_new_mount(struct path *pat
 			mnt_flags |= MNT_NODEV | MNT_LOCK_NODEV;
 		}
 		if (type->fs_flags & FS_USERNS_VISIBLE) {
-			if (!fs_fully_visible(type))
+			if (!fs_fully_visible(type, &mnt_flags))
 				return -EPERM;
 		}
 	}
@@ -3172,9 +3172,10 @@ bool current_chrooted(void)
 	return chrooted;
 }
 
-static bool fs_fully_visible(struct file_system_type *type)
+static bool fs_fully_visible(struct file_system_type *type, int *new_mnt_flags)
 {
 	struct mnt_namespace *ns = current->nsproxy->mnt_ns;
+	int new_flags = *new_mnt_flags;
 	struct mount *mnt;
 	bool visible = false;
 
@@ -3193,6 +3194,19 @@ static bool fs_fully_visible(struct file
 		if (mnt->mnt.mnt_root != mnt->mnt.mnt_sb->s_root)
 			continue;
 
+		/* Verify the mount flags are equal to or more permissive
+		 * than the proposed new mount.
+		 */
+		if ((mnt->mnt.mnt_flags & MNT_LOCK_READONLY) &&
+		    !(new_flags & MNT_READONLY))
+			continue;
+		if ((mnt->mnt.mnt_flags & MNT_LOCK_NODEV) &&
+		    !(new_flags & MNT_NODEV))
+			continue;
+		if ((mnt->mnt.mnt_flags & MNT_LOCK_ATIME) &&
+		    ((mnt->mnt.mnt_flags & MNT_ATIME_MASK) != (new_flags & MNT_ATIME_MASK)))
+			continue;
+
 		/* This mount is not fully visible if there are any
 		 * locked child mounts that cover anything except for
 		 * empty directories.
@@ -3206,6 +3220,10 @@ static bool fs_fully_visible(struct file
 			if (!is_empty_dir_inode(inode))
 				goto next;
 		}
+		/* Preserve the locked attributes */
+		*new_mnt_flags |= mnt->mnt.mnt_flags & (MNT_LOCK_READONLY | \
+							MNT_LOCK_NODEV    | \
+							MNT_LOCK_ATIME);
 		visible = true;
 		goto found;
 	next:	;
author maintainer
#9 lore raw

PATCH 9/58 sysfs: Create mountpoints with sysfs_create_mount_point

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Eric W. Biederman" <[email protected]>

commit f9bb48825a6b5d02f4cabcc78967c75db903dcdc upstream.

This allows for better documentation in the code and it allows for a simpler and fully correct version of fs_fully_visible to be written.

The mount points converted and their filesystems are:

/sys/hypervisor/s390/       s390_hypfs
/sys/kernel/config/         configfs
/sys/kernel/debug/          debugfs
/sys/firmware/efi/efivars/  efivarfs
/sys/fs/fuse/connections/   fusectl
/sys/fs/pstore/             pstore
/sys/kernel/tracing/        tracefs
/sys/fs/cgroup/             cgroup
/sys/kernel/security/       securityfs
/sys/fs/selinux/            selinuxfs
/sys/fs/smackfs/            smackfs
---
 arch/s390/hypfs/inode.c      |   12 ++++--------
 drivers/firmware/efi/efi.c   |    6 ++----
 fs/configfs/mount.c          |   10 ++++------
 fs/debugfs/inode.c           |   11 ++++-------
 fs/fuse/inode.c              |    9 +++------
 fs/pstore/inode.c            |   12 ++++--------
 kernel/cgroup.c              |   10 ++++------
 security/inode.c             |   10 ++++------
 security/selinux/selinuxfs.c |   11 +++++------
 security/smack/smackfs.c     |    8 ++++----
 10 files changed, 38 insertions(+), 61 deletions(-)
arch/s390/hypfs/inode.c +4 -8
@@ -458,8 +458,6 @@ static const struct super_operations hyp
 	.show_options	= hypfs_show_options,
 };
 
-static struct kobject *s390_kobj;
-
 static int __init hypfs_init(void)
 {
 	int rc;
@@ -483,18 +481,16 @@ static int __init hypfs_init(void)
 		rc = -ENODATA;
 		goto fail_hypfs_sprp_exit;
 	}
-	s390_kobj = kobject_create_and_add("s390", hypervisor_kobj);
-	if (!s390_kobj) {
-		rc = -ENOMEM;
+	rc = sysfs_create_mount_point(hypervisor_kobj, "s390");
+	if (rc)
 		goto fail_hypfs_diag0c_exit;
-	}
 	rc = register_filesystem(&hypfs_type);
 	if (rc)
 		goto fail_filesystem;
 	return 0;
 
 fail_filesystem:
-	kobject_put(s390_kobj);
+	sysfs_remove_mount_point(hypervisor_kobj, "s390");
 fail_hypfs_diag0c_exit:
 	hypfs_diag0c_exit();
 fail_hypfs_sprp_exit:
@@ -512,7 +508,7 @@ fail_dbfs_exit:
 static void __exit hypfs_exit(void)
 {
 	unregister_filesystem(&hypfs_type);
-	kobject_put(s390_kobj);
+	sysfs_remove_mount_point(hypervisor_kobj, "s390");
 	hypfs_diag0c_exit();
 	hypfs_sprp_exit();
 	hypfs_vm_exit();
drivers/firmware/efi/efi.c +2 -4
@@ -65,7 +65,6 @@ static int __init parse_efi_cmdline(char
 early_param("efi", parse_efi_cmdline);
 
 static struct kobject *efi_kobj;
-static struct kobject *efivars_kobj;
 
 /*
  * Let's not leave out systab information that snuck into
@@ -212,10 +211,9 @@ static int __init efisubsys_init(void)
 		goto err_remove_group;
 
 	/* and the standard mountpoint for efivarfs */
-	efivars_kobj = kobject_create_and_add("efivars", efi_kobj);
-	if (!efivars_kobj) {
+	error = sysfs_create_mount_point(efi_kobj, "efivars");
+	if (error) {
 		pr_err("efivars: Subsystem registration failed.\n");
-		error = -ENOMEM;
 		goto err_remove_group;
 	}
 
fs/configfs/mount.c +4 -6
@@ -129,8 +129,6 @@ void configfs_release_fs(void)
 }
 
 
-static struct kobject *config_kobj;
-
 static int __init configfs_init(void)
 {
 	int err = -ENOMEM;
@@ -141,8 +139,8 @@ static int __init configfs_init(void)
 	if (!configfs_dir_cachep)
 		goto out;
 
-	config_kobj = kobject_create_and_add("config", kernel_kobj);
-	if (!config_kobj)
+	err = sysfs_create_mount_point(kernel_kobj, "config");
+	if (err)
 		goto out2;
 
 	err = register_filesystem(&configfs_fs_type);
@@ -152,7 +150,7 @@ static int __init configfs_init(void)
 	return 0;
 out3:
 	pr_err("Unable to register filesystem!\n");
-	kobject_put(config_kobj);
+	sysfs_remove_mount_point(kernel_kobj, "config");
 out2:
 	kmem_cache_destroy(configfs_dir_cachep);
 	configfs_dir_cachep = NULL;
@@ -163,7 +161,7 @@ out:
 static void __exit configfs_exit(void)
 {
 	unregister_filesystem(&configfs_fs_type);
-	kobject_put(config_kobj);
+	sysfs_remove_mount_point(kernel_kobj, "config");
 	kmem_cache_destroy(configfs_dir_cachep);
 	configfs_dir_cachep = NULL;
 }
fs/debugfs/inode.c +4 -7
@@ -713,20 +713,17 @@ bool debugfs_initialized(void)
 }
 EXPORT_SYMBOL_GPL(debugfs_initialized);
 
-
-static struct kobject *debug_kobj;
-
 static int __init debugfs_init(void)
 {
 	int retval;
 
-	debug_kobj = kobject_create_and_add("debug", kernel_kobj);
-	if (!debug_kobj)
-		return -EINVAL;
+	retval = sysfs_create_mount_point(kernel_kobj, "debug");
+	if (retval)
+		return retval;
 
 	retval = register_filesystem(&debug_fs_type);
 	if (retval)
-		kobject_put(debug_kobj);
+		sysfs_remove_mount_point(kernel_kobj, "debug");
 	else
 		debugfs_registered = true;
 
fs/fuse/inode.c +3 -6
@@ -1238,7 +1238,6 @@ static void fuse_fs_cleanup(void)
 }
 
 static struct kobject *fuse_kobj;
-static struct kobject *connections_kobj;
 
 static int fuse_sysfs_init(void)
 {
@@ -1250,11 +1249,9 @@ static int fuse_sysfs_init(void)
 		goto out_err;
 	}
 
-	connections_kobj = kobject_create_and_add("connections", fuse_kobj);
-	if (!connections_kobj) {
-		err = -ENOMEM;
+	err = sysfs_create_mount_point(fuse_kobj, "connections");
+	if (err)
 		goto out_fuse_unregister;
-	}
 
 	return 0;
 
@@ -1266,7 +1263,7 @@ static int fuse_sysfs_init(void)
 
 static void fuse_sysfs_cleanup(void)
 {
-	kobject_put(connections_kobj);
+	sysfs_remove_mount_point(fuse_kobj, "connections");
 	kobject_put(fuse_kobj);
 }
 
fs/pstore/inode.c +4 -8
@@ -458,22 +458,18 @@ static struct file_system_type pstore_fs
 	.kill_sb	= pstore_kill_sb,
 };
 
-static struct kobject *pstore_kobj;
-
 static int __init init_pstore_fs(void)
 {
-	int err = 0;
+	int err;
 
 	/* Create a convenient mount point for people to access pstore */
-	pstore_kobj = kobject_create_and_add("pstore", fs_kobj);
-	if (!pstore_kobj) {
-		err = -ENOMEM;
+	err = sysfs_create_mount_point(fs_kobj, "pstore");
+	if (err)
 		goto out;
-	}
 
 	err = register_filesystem(&pstore_fs_type);
 	if (err < 0)
-		kobject_put(pstore_kobj);
+		sysfs_remove_mount_point(fs_kobj, "pstore");
 
 out:
 	return err;
kernel/cgroup.c +4 -6
@@ -1924,8 +1924,6 @@ static struct file_system_type cgroup_fs
 	.kill_sb = cgroup_kill_sb,
 };
 
-static struct kobject *cgroup_kobj;
-
 /**
  * task_cgroup_path - cgroup path of a task in the first cgroup hierarchy
  * @task: target task
@@ -5042,13 +5040,13 @@ int __init cgroup_init(void)
 		}
 	}
 
-	cgroup_kobj = kobject_create_and_add("cgroup", fs_kobj);
-	if (!cgroup_kobj)
-		return -ENOMEM;
+	err = sysfs_create_mount_point(fs_kobj, "cgroup");
+	if (err)
+		return err;
 
 	err = register_filesystem(&cgroup_fs_type);
 	if (err < 0) {
-		kobject_put(cgroup_kobj);
+		sysfs_remove_mount_point(fs_kobj, "cgroup");
 		return err;
 	}
 
security/inode.c +4 -6
@@ -215,19 +215,17 @@ void securityfs_remove(struct dentry *de
 }
 EXPORT_SYMBOL_GPL(securityfs_remove);
 
-static struct kobject *security_kobj;
-
 static int __init securityfs_init(void)
 {
 	int retval;
 
-	security_kobj = kobject_create_and_add("security", kernel_kobj);
-	if (!security_kobj)
-		return -EINVAL;
+	retval = sysfs_create_mount_point(kernel_kobj, "security");
+	if (retval)
+		return retval;
 
 	retval = register_filesystem(&fs_type);
 	if (retval)
-		kobject_put(security_kobj);
+		sysfs_remove_mount_point(kernel_kobj, "security");
 	return retval;
 }
 
security/selinux/selinuxfs.c +5 -6
@@ -1853,7 +1853,6 @@ static struct file_system_type sel_fs_ty
 };
 
 struct vfsmount *selinuxfs_mount;
-static struct kobject *selinuxfs_kobj;
 
 static int __init init_sel_fs(void)
 {
@@ -1862,13 +1861,13 @@ static int __init init_sel_fs(void)
 	if (!selinux_enabled)
 		return 0;
 
-	selinuxfs_kobj = kobject_create_and_add("selinux", fs_kobj);
-	if (!selinuxfs_kobj)
-		return -ENOMEM;
+	err = sysfs_create_mount_point(fs_kobj, "selinux");
+	if (err)
+		return err;
 
 	err = register_filesystem(&sel_fs_type);
 	if (err) {
-		kobject_put(selinuxfs_kobj);
+		sysfs_remove_mount_point(fs_kobj, "selinux");
 		return err;
 	}
 
@@ -1887,7 +1886,7 @@ __initcall(init_sel_fs);
 #ifdef CONFIG_SECURITY_SELINUX_DISABLE
 void exit_sel_fs(void)
 {
-	kobject_put(selinuxfs_kobj);
+	sysfs_remove_mount_point(fs_kobj, "selinux");
 	kern_unmount(selinuxfs_mount);
 	unregister_filesystem(&sel_fs_type);
 }
security/smack/smackfs.c +4 -4
@@ -2150,16 +2150,16 @@ static const struct file_operations smk_
 	.llseek		= generic_file_llseek,
 };
 
-static struct kset *smackfs_kset;
 /**
  * smk_init_sysfs - initialize /sys/fs/smackfs
  *
  */
 static int smk_init_sysfs(void)
 {
-	smackfs_kset = kset_create_and_add("smackfs", NULL, fs_kobj);
-	if (!smackfs_kset)
-		return -ENOMEM;
+	int err;
+	err = sysfs_create_mount_point(fs_kobj, "smackfs");
+	if (err)
+		return err;
 	return 0;
 }
 
author maintainer
#10 lore raw

PATCH 10/58 gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Aaron Lu <[email protected]>

commit 61e749d7e1627d375156553ea0ae83c4f6bb5a9b upstream.

The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq desc's wake_depth unbalanced warning during system resume phase from the gpio_keys driver, which is the driver for the power button of the ASUS T100 laptop.

---
 drivers/gpio/gpio-crystalcove.c |    1 +
 1 file changed, 1 insertion(+)
drivers/gpio/gpio-crystalcove.c +1 -0
@@ -250,6 +250,7 @@ static struct irq_chip crystalcove_irqch
 	.irq_set_type		= crystalcove_irq_type,
 	.irq_bus_lock		= crystalcove_bus_lock,
 	.irq_bus_sync_unlock	= crystalcove_bus_sync_unlock,
+	.flags			= IRQCHIP_SKIP_SET_WAKE,
 };
 
 static irqreturn_t crystalcove_gpio_irq_handler(int irq, void *data)
author maintainer
#11 lore raw

PATCH 11/58 rcu: Correctly handle non-empty Tiny RCU callback list with none ready

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Paul E. McKenney" <[email protected]>

commit 6e91f8cb138625be96070b778d9ba71ce520ea7e upstream.

If, at the time __rcu_process_callbacks() is invoked, there are callbacks in Tiny RCU's callback list, but none of them are ready to be invoked, the current list-management code will knit the non-ready callbacks out of the list. This can result in hangs and possibly worse. This commit therefore inserts a check for there being no callbacks that can be invoked immediately.

This bug is unlikely to occur -- you have to get a new callback between the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to __rcu_process_callbacks(). It was detected by the addition of RCU-bh testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's mutation testing. Although this bug was made much more likely by 915e8a4fe45e (rcu: Remove fastpath from __rcu_process_callbacks()), this
did not cause the bug, but rather made it much more probable. That
said, it takes more than 40 hours of rcutorture testing, on average, for this bug to appear, so this fix cannot be considered an emergency.

---
 kernel/rcu/tiny.c |    5 +++++
 1 file changed, 5 insertions(+)
kernel/rcu/tiny.c +5 -0
@@ -182,6 +182,11 @@ static void __rcu_process_callbacks(stru
 
 	/* Move the ready-to-invoke callbacks to a local list. */
 	local_irq_save(flags);
+	if (rcp->donetail == &rcp->rcucblist) {
+		/* No callbacks ready, so just leave. */
+		local_irq_restore(flags);
+		return;
+	}
 	RCU_TRACE(trace_rcu_batch_start(rcp->name, 0, rcp->qlen, -1));
 	list = rcp->rcucblist;
 	rcp->rcucblist = *rcp->donetail;
author maintainer
#12 lore raw

PATCH 12/58 ipr: Increase default adapter init stage change timeout

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Brian King <[email protected]>

commit 45c44b5ff9caa743ed9c2bfd44307c536c9caf1e upstream.

Increase the default init stage change timeout from 15 seconds to 30 seconds. This resolves issues we have seen with some adapters not transitioning to the first init stage within 15 seconds, which results in adapter initialization failures.

---
 drivers/scsi/ipr.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/ipr.h +1 -1
@@ -268,7 +268,7 @@
 #define IPR_RUNTIME_RESET				0x40000000
 
 #define IPR_IPL_INIT_MIN_STAGE_TIME			5
-#define IPR_IPL_INIT_DEFAULT_STAGE_TIME                 15
+#define IPR_IPL_INIT_DEFAULT_STAGE_TIME                 30
 #define IPR_IPL_INIT_STAGE_UNKNOWN			0x0
 #define IPR_IPL_INIT_STAGE_TRANSOP			0xB0000000
 #define IPR_IPL_INIT_STAGE_MASK				0xff000000
author maintainer
#13 lore raw

PATCH 13/58 Disable write buffering on Toshiba ToPIC95

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ryan Underwood <[email protected]>

commit 2fb22a8042fe96b4220843f79241c116d90922c4 upstream.

Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961

---
 drivers/pcmcia/topic.h |   16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/pcmcia/topic.h +16 -0
@@ -104,6 +104,9 @@
 #define TOPIC_EXCA_IF_CONTROL		0x3e	/* 8 bit */
 #define TOPIC_EXCA_IFC_33V_ENA		0x01
 
+#define TOPIC_PCI_CFG_PPBCN		0x3e	/* 16-bit */
+#define TOPIC_PCI_CFG_PPBCN_WBEN	0x0400
+
 static void topic97_zoom_video(struct pcmcia_socket *sock, int onoff)
 {
 	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
@@ -138,6 +141,7 @@ static int topic97_override(struct yenta
 static int topic95_override(struct yenta_socket *socket)
 {
 	u8 fctrl;
+	u16 ppbcn;
 
 	/* enable 3.3V support for 16bit cards */
 	fctrl = exca_readb(socket, TOPIC_EXCA_IF_CONTROL);
@@ -146,6 +150,18 @@ static int topic95_override(struct yenta
 	/* tell yenta to use exca registers to power 16bit cards */
 	socket->flags |= YENTA_16BIT_POWER_EXCA | YENTA_16BIT_POWER_DF;
 
+	/* Disable write buffers to prevent lockups under load with numerous
+	   Cardbus cards, observed on Tecra 500CDT and reported elsewhere on the
+	   net.  This is not a power-on default according to the datasheet
+	   but some BIOSes seem to set it. */
+	if (pci_read_config_word(socket->dev, TOPIC_PCI_CFG_PPBCN, &ppbcn) == 0
+	    && socket->dev->revision <= 7
+	    && (ppbcn & TOPIC_PCI_CFG_PPBCN_WBEN)) {
+		ppbcn &= ~TOPIC_PCI_CFG_PPBCN_WBEN;
+		pci_write_config_word(socket->dev, TOPIC_PCI_CFG_PPBCN, ppbcn);
+		dev_info(&socket->dev->dev, "Disabled ToPIC95 Cardbus write buffers.\n");
+	}
+
 	return 0;
 }
 
author maintainer
#14 lore raw

PATCH 14/58 ALSA: pcm: Fix pcm_class sysfs output

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <[email protected]>

commit 60b93030b44a8c2cd015cebe5624fd7552ec67ec upstream.

The pcm_class sysfs of each PCM substream gives only "none" since the recent code change to embed the struct device. Fix the code to point directly to the embedded device object properly.

Fixes ef46c7af93f9 ('ALSA: pcm: Embed struct device')
---
 sound/core/pcm.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
sound/core/pcm.c +3 -3
@@ -1044,7 +1044,8 @@ void snd_pcm_detach_substream(struct snd
 static ssize_t show_pcm_class(struct device *dev,
 			      struct device_attribute *attr, char *buf)
 {
-	struct snd_pcm *pcm;
+	struct snd_pcm_str *pstr = container_of(dev, struct snd_pcm_str, dev);
+	struct snd_pcm *pcm = pstr->pcm;
 	const char *str;
 	static const char *strs[SNDRV_PCM_CLASS_LAST + 1] = {
 		[SNDRV_PCM_CLASS_GENERIC] = "generic",
@@ -1053,8 +1054,7 @@ static ssize_t show_pcm_class(struct dev
 		[SNDRV_PCM_CLASS_DIGITIZER] = "digitizer",
 	};
 
-	if (! (pcm = dev_get_drvdata(dev)) ||
-	    pcm->dev_class > SNDRV_PCM_CLASS_LAST)
+	if (pcm->dev_class > SNDRV_PCM_CLASS_LAST)
 		str = "none";
 	else
 		str = strs[pcm->dev_class];
author maintainer
#15 lore raw

PATCH 15/58 ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Henningsson <[email protected]>

commit ec56af67a10a0d82b79027878a81fce08d002d50 upstream.

Thinkpad X250, when attached to a dock, has two headphone outs but no line out. Make sure we don't try to turn this into one headphone and one line out (since that disables the headphone amp on the dock).

Alsa-info at http://www.alsa-project.org/db/?f=36f8764e1d782397928feec715d0ef90dfddd4c1

---
 sound/pci/hda/patch_realtek.c |    7 +++++++
 1 file changed, 7 insertions(+)
sound/pci/hda/patch_realtek.c +7 -0
@@ -4421,6 +4421,7 @@ enum {
 	ALC255_FIXUP_HEADSET_MODE_NO_HP_MIC,
 	ALC293_FIXUP_DELL1_MIC_NO_PRESENCE,
 	ALC292_FIXUP_TPT440_DOCK,
+	ALC292_FIXUP_TPT440_DOCK2,
 	ALC283_FIXUP_BXBT2807_MIC,
 	ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED,
 	ALC282_FIXUP_ASPIRE_V5_PINS,
@@ -4864,6 +4865,12 @@ static const struct hda_fixup alc269_fix
 		.chain_id = ALC269_FIXUP_HEADSET_MODE
 	},
 	[ALC292_FIXUP_TPT440_DOCK] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc269_fixup_pincfg_no_hp_to_lineout,
+		.chained = true,
+		.chain_id = ALC292_FIXUP_TPT440_DOCK2
+	},
+	[ALC292_FIXUP_TPT440_DOCK2] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
 			{ 0x16, 0x21211010 }, /* dock headphone */
author maintainer
#16 lore raw

PATCH 16/58 ALSA: hda - set proper caps for newer AMD hda audio in KB/KV

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit 650474fb737c3e0ea0f6ab8e43c2cd161080ce5c upstream.

Fixes audio problems on newer asics.

Noticed by: Kelly Anderson <[email protected]>

---
 sound/pci/hda/hda_intel.c |    4 ++++
 1 file changed, 4 insertions(+)
sound/pci/hda/hda_intel.c +4 -0
@@ -2056,6 +2056,8 @@ static const struct pci_device_id azx_id
 	{ PCI_DEVICE(0x1022, 0x780d),
 	  .driver_data = AZX_DRIVER_GENERIC | AZX_DCAPS_PRESET_ATI_SB },
 	/* ATI HDMI */
+	{ PCI_DEVICE(0x1002, 0x1308),
+	  .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS },
 	{ PCI_DEVICE(0x1002, 0x793b),
 	  .driver_data = AZX_DRIVER_ATIHDMI | AZX_DCAPS_PRESET_ATI_HDMI },
 	{ PCI_DEVICE(0x1002, 0x7919),
@@ -2064,6 +2066,8 @@ static const struct pci_device_id azx_id
 	  .driver_data = AZX_DRIVER_ATIHDMI | AZX_DCAPS_PRESET_ATI_HDMI },
 	{ PCI_DEVICE(0x1002, 0x970f),
 	  .driver_data = AZX_DRIVER_ATIHDMI | AZX_DCAPS_PRESET_ATI_HDMI },
+	{ PCI_DEVICE(0x1002, 0x9840),
+	  .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS },
 	{ PCI_DEVICE(0x1002, 0xaa00),
 	  .driver_data = AZX_DRIVER_ATIHDMI | AZX_DCAPS_PRESET_ATI_HDMI },
 	{ PCI_DEVICE(0x1002, 0xaa08),
author maintainer
#17 lore raw

PATCH 17/58 ALSA: hda - Add headset support to Acer Aspire V5

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <[email protected]>

commit 7819717b11346b8a5420b223b46600e394049c66 upstream.

Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell laptops to support the headset mic. The headset mic pin is 0x19 and it's not exposed by BIOS, thus we need to fix the pincfg as well.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201

---
 sound/pci/hda/patch_realtek.c |   12 ++++++++++++
 1 file changed, 12 insertions(+)
sound/pci/hda/patch_realtek.c +12 -0
@@ -4394,6 +4394,7 @@ enum {
 	ALC269_FIXUP_DELL3_MIC_NO_PRESENCE,
 	ALC269_FIXUP_HEADSET_MODE,
 	ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC,
+	ALC269_FIXUP_ASPIRE_HEADSET_MIC,
 	ALC269_FIXUP_ASUS_X101_FUNC,
 	ALC269_FIXUP_ASUS_X101_VERB,
 	ALC269_FIXUP_ASUS_X101,
@@ -4663,6 +4664,15 @@ static const struct hda_fixup alc269_fix
 		.type = HDA_FIXUP_FUNC,
 		.v.func = alc_fixup_headset_mode_no_hp_mic,
 	},
+	[ALC269_FIXUP_ASPIRE_HEADSET_MIC] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x01a1913c }, /* headset mic w/o jack detect */
+			{ }
+		},
+		.chained = true,
+		.chain_id = ALC269_FIXUP_HEADSET_MODE,
+	},
 	[ALC286_FIXUP_SONY_MIC_NO_PRESENCE] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -4937,6 +4947,8 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x1025, 0x029b, "Acer 1810TZ", ALC269_FIXUP_INV_DMIC),
 	SND_PCI_QUIRK(0x1025, 0x0349, "Acer AOD260", ALC269_FIXUP_INV_DMIC),
 	SND_PCI_QUIRK(0x1025, 0x047c, "Acer AC700", ALC269_FIXUP_ACER_AC700),
+	SND_PCI_QUIRK(0x1025, 0x072d, "Acer Aspire V5-571G", ALC269_FIXUP_ASPIRE_HEADSET_MIC),
+	SND_PCI_QUIRK(0x1025, 0x080d, "Acer Aspire V5-122P", ALC269_FIXUP_ASPIRE_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1025, 0x0740, "Acer AO725", ALC271_FIXUP_HP_GATE_MIC_JACK),
 	SND_PCI_QUIRK(0x1025, 0x0742, "Acer AO756", ALC271_FIXUP_HP_GATE_MIC_JACK),
 	SND_PCI_QUIRK(0x1025, 0x0775, "Acer Aspire E1-572", ALC271_FIXUP_HP_GATE_MIC_JACK_E1_572),
author maintainer
#18 lore raw

PATCH 18/58 ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <[email protected]>

commit 4df3fd1700abbb53bd874143dfd1f9ac9e7cbf4b upstream.

Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of the two headphones, thus the driver tries to assign another as the line-out, and this results in the inconsistent mapping between the created jack ctl and the actual I/O. Due to this, PulseAudio doesn't handle it properly and gets the silent output.

The fix is to ignore the non-HP sequencer checks.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681

---
 sound/pci/hda/patch_realtek.c |    6 ++++++
 1 file changed, 6 insertions(+)
sound/pci/hda/patch_realtek.c +6 -0
@@ -4374,6 +4374,7 @@ enum {
 	ALC269_FIXUP_LIFEBOOK,
 	ALC269_FIXUP_LIFEBOOK_EXTMIC,
 	ALC269_FIXUP_LIFEBOOK_HP_PIN,
+	ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT,
 	ALC269_FIXUP_AMIC,
 	ALC269_FIXUP_DMIC,
 	ALC269VB_FIXUP_AMIC,
@@ -4536,6 +4537,10 @@ static const struct hda_fixup alc269_fix
 			{ }
 		},
 	},
+	[ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = alc269_fixup_pincfg_no_hp_to_lineout,
+	},
 	[ALC269_FIXUP_AMIC] = {
 		.type = HDA_FIXUP_PINS,
 		.v.pins = (const struct hda_pintbl[]) {
@@ -5046,6 +5051,7 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x104d, 0x9084, "Sony VAIO", ALC275_FIXUP_SONY_HWEQ),
 	SND_PCI_QUIRK(0x104d, 0x9099, "Sony VAIO S13", ALC275_FIXUP_SONY_DISABLE_AAMIX),
 	SND_PCI_QUIRK(0x10cf, 0x1475, "Lifebook", ALC269_FIXUP_LIFEBOOK),
+	SND_PCI_QUIRK(0x10cf, 0x159f, "Lifebook E780", ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT),
 	SND_PCI_QUIRK(0x10cf, 0x15dc, "Lifebook T731", ALC269_FIXUP_LIFEBOOK_HP_PIN),
 	SND_PCI_QUIRK(0x10cf, 0x1757, "Lifebook E752", ALC269_FIXUP_LIFEBOOK_HP_PIN),
 	SND_PCI_QUIRK(0x10cf, 0x1845, "Lifebook U904", ALC269_FIXUP_LIFEBOOK_EXTMIC),
author maintainer
#19 lore raw

PATCH 19/58 ACPI / init: Switch over platform to the ACPI mode later

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Rafael J. Wysocki" <[email protected]>

commit b064a8fa77dfead647564c46ac8fc5b13bd1ab73 upstream.

Commit 73f7d1ca3263 "ACPI / init: Run acpi_early_init() before timekeeping_init()" moved the ACPI subsystem initialization, including the ACPI mode enabling, to an earlier point in the initialization sequence, to allow the timekeeping subsystem use ACPI early. Unfortunately, that resulted in boot regressions on some systems and the early ACPI initialization was moved toward its original position in the kernel initialization code by commit c4e1acbb35e4 "ACPI / init: Invoke early ACPI initialization later".

However, that turns out to be insufficient, as boot is still broken on the Tyan S8812 mainboard.

To fix that issue, split the ACPI early initialization code into two pieces so the majority of it still located in acpi_early_init() and the part switching over the platform into the ACPI mode goes into a new function, acpi_subsystem_init(), executed at the original early ACPI initialization spot.

That fixes the Tyan S8812 boot problem, but still allows ACPI tables to be loaded earlier which is useful to the EFI code in efi_enter_virtual_mode().

---
 drivers/acpi/bus.c   |   56 +++++++++++++++++++++++++++++++++++++--------------
 include/linux/acpi.h |    2 +
 init/main.c          |    1 
 3 files changed, 44 insertions(+), 15 deletions(-)
drivers/acpi/bus.c +41 -15
@@ -467,6 +467,16 @@ static int __init acpi_bus_init_irq(void
 	return 0;
 }
 
+/**
+ * acpi_early_init - Initialize ACPICA and populate the ACPI namespace.
+ *
+ * The ACPI tables are accessible after this, but the handling of events has not
+ * been initialized and the global lock is not available yet, so AML should not
+ * be executed at this point.
+ *
+ * Doing this before switching the EFI runtime services to virtual mode allows
+ * the EfiBootServices memory to be freed slightly earlier on boot.
+ */
 void __init acpi_early_init(void)
 {
 	acpi_status status;
@@ -530,26 +540,42 @@ void __init acpi_early_init(void)
 		acpi_gbl_FADT.sci_interrupt = acpi_sci_override_gsi;
 	}
 #endif
+	return;
+
+ error0:
+	disable_acpi();
+}
+
+/**
+ * acpi_subsystem_init - Finalize the early initialization of ACPI.
+ *
+ * Switch over the platform to the ACPI mode (if possible), initialize the
+ * handling of ACPI events, install the interrupt and global lock handlers.
+ *
+ * Doing this too early is generally unsafe, but at the same time it needs to be
+ * done before all things that really depend on ACPI.  The right spot appears to
+ * be before finalizing the EFI initialization.
+ */
+void __init acpi_subsystem_init(void)
+{
+	acpi_status status;
+
+	if (acpi_disabled)
+		return;
 
 	status = acpi_enable_subsystem(~ACPI_NO_ACPI_ENABLE);
 	if (ACPI_FAILURE(status)) {
 		printk(KERN_ERR PREFIX "Unable to enable ACPI\n");
-		goto error0;
+		disable_acpi();
+	} else {
+		/*
+		 * If the system is using ACPI then we can be reasonably
+		 * confident that any regulators are managed by the firmware
+		 * so tell the regulator core it has everything it needs to
+		 * know.
+		 */
+		regulator_has_full_constraints();
 	}
-
-	/*
-	 * If the system is using ACPI then we can be reasonably
-	 * confident that any regulators are managed by the firmware
-	 * so tell the regulator core it has everything it needs to
-	 * know.
-	 */
-	regulator_has_full_constraints();
-
-	return;
-
-      error0:
-	disable_acpi();
-	return;
 }
 
 static int __init acpi_bus_init(void)
include/linux/acpi.h +2 -0
@@ -428,6 +428,7 @@ extern acpi_status acpi_pci_osc_control_
 #define ACPI_OST_SC_INSERT_NOT_SUPPORTED	0x82
 
 extern void acpi_early_init(void);
+extern void acpi_subsystem_init(void);
 
 extern int acpi_nvs_register(__u64 start, __u64 size);
 
@@ -477,6 +478,7 @@ static inline const char *acpi_dev_name(
 }
 
 static inline void acpi_early_init(void) { }
+static inline void acpi_subsystem_init(void) { }
 
 static inline int early_acpi_boot_init(void)
 {
init/main.c +1 -0
@@ -661,6 +661,7 @@ asmlinkage __visible void __init start_k
 
 	check_bugs();
 
+	acpi_subsystem_init();
 	sfi_init_late();
 
 	if (efi_enabled(EFI_RUNTIME_SERVICES)) {
author maintainer
#20 lore raw

PATCH 20/58 ACPI / PM: Add missing pm_generic_complete() invocation

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Rafael J. Wysocki" <[email protected]>

commit 3d56402d3fa8d10749eeb36293dd1992bd5ad0c3 upstream.

Add missing invocation of pm_generic_complete() to acpi_subsys_complete() to allow ->complete callbacks provided by the drivers of devices using the ACPI PM domain to be executed during system resume.

Fixes f25c0ae2b4c4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
---
 drivers/acpi/device_pm.c |    1 +
 1 file changed, 1 insertion(+)
drivers/acpi/device_pm.c +1 -0
@@ -953,6 +953,7 @@ EXPORT_SYMBOL_GPL(acpi_subsys_prepare);
  */
 void acpi_subsys_complete(struct device *dev)
 {
+	pm_generic_complete(dev);
 	/*
 	 * If the device had been runtime-suspended before the system went into
 	 * the sleep state it is going out of and it has never been resumed till
author maintainer
#21 lore raw

PATCH 21/58 iio: accel: kxcjk-1013: add the "KXCJ9000" ACPI id

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Antonio Ospite <[email protected]>

commit 61e2c70da9cfc79e8485eafa0f98b5919b04bbe1 upstream.

This id has been seen in the DSDT of the Teclast X98 Air 3G tablet based on Intel Bay Trail.

---
 drivers/iio/accel/kxcjk-1013.c |    1 +
 1 file changed, 1 insertion(+)
drivers/iio/accel/kxcjk-1013.c +1 -0
@@ -1422,6 +1422,7 @@ static const struct dev_pm_ops kxcjk1013
 static const struct acpi_device_id kx_acpi_match[] = {
 	{"KXCJ1013", KXCJK1013},
 	{"KXCJ1008", KXCJ91008},
+	{"KXCJ9000", KXCJ91008},
 	{"KXTJ1009", KXTJ21009},
 	{"SMO8500",  KXCJ91008},
 	{ },
author maintainer
#22 lore raw

PATCH 22/58 tools selftests: Fix clean target with make 3.81

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arnaldo Carvalho de Melo <[email protected]>

commit 60df4642a83546fa6ea8286f5094ce8c0906c3ec upstream.

Make 3.81 doesn't have the 'undefine' command. Using undefine to clear LDFLAGS fails when make version 3.81 is used. Fix it to use override to clear LDFLAGS.

---
 tools/testing/selftests/Makefile |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/Makefile +1 -1
@@ -26,7 +26,7 @@ TARGETS_HOTPLUG += memory-hotplug
 # Makefile to avoid test build failures when test
 # Makefile doesn't have explicit build rules.
 ifeq (1,$(MAKELEVEL))
-undefine LDFLAGS
+override LDFLAGS =
 override MAKEFLAGS =
 endif
 
author maintainer
#23 lore raw

PATCH 23/58 ARC: add smp barriers around atomics per Documentation/atomic_ops.txt

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vineet Gupta <[email protected]>

commit 2576c28e3f623ed401db7e6197241865328620ef upstream.

- arch_spin_lock/unlock were lacking the ACQUIRE/RELEASE barriers Since ARCv2 only provides load/load, store/store and all/all, we need the full barrier

- LLOCK/SCOND based atomics, bitops, cmpxchg, which return modified values were lacking the explicit smp barriers.

- Non LLOCK/SCOND varaints don't need the explicit barriers since that is implicity provided by the spin locks used to implement the critical section (the spin lock barriers in turn are also fixed in this commit as explained above

---
 arch/arc/include/asm/atomic.h   |   21 +++++++++++++++++++++
 arch/arc/include/asm/bitops.h   |   19 +++++++++++++++++++
 arch/arc/include/asm/cmpxchg.h  |   17 +++++++++++++++++
 arch/arc/include/asm/spinlock.h |   32 ++++++++++++++++++++++++++++++++
 4 files changed, 89 insertions(+)
arch/arc/include/asm/atomic.h +21 -0
@@ -43,6 +43,12 @@ static inline int atomic_##op##_return(i
 {									\
 	unsigned int temp;						\
 									\
+	/*								\
+	 * Explicit full memory barrier needed before/after as		\
+	 * LLOCK/SCOND thmeselves don't provide any such semantics	\
+	 */								\
+	smp_mb();							\
+									\
 	__asm__ __volatile__(						\
 	"1:	llock   %0, [%1]	\n"				\
 	"	" #asm_op " %0, %0, %2	\n"				\
@@ -52,6 +58,8 @@ static inline int atomic_##op##_return(i
 	: "r"(&v->counter), "ir"(i)					\
 	: "cc");							\
 									\
+	smp_mb();							\
+									\
 	return temp;							\
 }
 
@@ -105,6 +113,9 @@ static inline int atomic_##op##_return(i
 	unsigned long flags;						\
 	unsigned long temp;						\
 									\
+	/*								\
+	 * spin lock/unlock provides the needed smp_mb() before/after	\
+	 */								\
 	atomic_ops_lock(flags);						\
 	temp = v->counter;						\
 	temp c_op i;							\
@@ -142,9 +153,19 @@ ATOMIC_OP(and, &=, and)
 #define __atomic_add_unless(v, a, u)					\
 ({									\
 	int c, old;							\
+									\
+	/*								\
+	 * Explicit full memory barrier needed before/after as		\
+	 * LLOCK/SCOND thmeselves don't provide any such semantics	\
+	 */								\
+	smp_mb();							\
+									\
 	c = atomic_read(v);						\
 	while (c != (u) && (old = atomic_cmpxchg((v), c, c + (a))) != c)\
 		c = old;						\
+									\
+	smp_mb();							\
+									\
 	c;								\
 })
 
arch/arc/include/asm/bitops.h +19 -0
@@ -103,6 +103,12 @@ static inline int test_and_set_bit(unsig
 	if (__builtin_constant_p(nr))
 		nr &= 0x1f;
 
+	/*
+	 * Explicit full memory barrier needed before/after as
+	 * LLOCK/SCOND themselves don't provide any such semantics
+	 */
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	llock   %0, [%2]	\n"
 	"	bset    %1, %0, %3	\n"
@@ -112,6 +118,8 @@ static inline int test_and_set_bit(unsig
 	: "r"(m), "ir"(nr)
 	: "cc");
 
+	smp_mb();
+
 	return (old & (1 << nr)) != 0;
 }
 
@@ -125,6 +133,8 @@ test_and_clear_bit(unsigned long nr, vol
 	if (__builtin_constant_p(nr))
 		nr &= 0x1f;
 
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	llock   %0, [%2]	\n"
 	"	bclr    %1, %0, %3	\n"
@@ -134,6 +144,8 @@ test_and_clear_bit(unsigned long nr, vol
 	: "r"(m), "ir"(nr)
 	: "cc");
 
+	smp_mb();
+
 	return (old & (1 << nr)) != 0;
 }
 
@@ -147,6 +159,8 @@ test_and_change_bit(unsigned long nr, vo
 	if (__builtin_constant_p(nr))
 		nr &= 0x1f;
 
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	llock   %0, [%2]	\n"
 	"	bxor    %1, %0, %3	\n"
@@ -156,6 +170,8 @@ test_and_change_bit(unsigned long nr, vo
 	: "r"(m), "ir"(nr)
 	: "cc");
 
+	smp_mb();
+
 	return (old & (1 << nr)) != 0;
 }
 
@@ -235,6 +251,9 @@ static inline int test_and_set_bit(unsig
 	if (__builtin_constant_p(nr))
 		nr &= 0x1f;
 
+	/*
+	 * spin lock/unlock provide the needed smp_mb() before/after
+	 */
 	bitops_lock(flags);
 
 	old = *m;
arch/arc/include/asm/cmpxchg.h +17 -0
@@ -10,6 +10,8 @@
 #define __ASM_ARC_CMPXCHG_H
 
 #include <linux/types.h>
+
+#include <asm/barrier.h>
 #include <asm/smp.h>
 
 #ifdef CONFIG_ARC_HAS_LLSC
@@ -19,6 +21,12 @@ __cmpxchg(volatile void *ptr, unsigned l
 {
 	unsigned long prev;
 
+	/*
+	 * Explicit full memory barrier needed before/after as
+	 * LLOCK/SCOND thmeselves don't provide any such semantics
+	 */
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	llock   %0, [%1]	\n"
 	"	brne    %0, %2, 2f	\n"
@@ -30,6 +38,8 @@ __cmpxchg(volatile void *ptr, unsigned l
 	  "r"(new) /* can't be "ir". scond can't take limm for "b" */
 	: "cc");
 
+	smp_mb();
+
 	return prev;
 }
 
@@ -42,6 +52,9 @@ __cmpxchg(volatile void *ptr, unsigned l
 	int prev;
 	volatile unsigned long *p = ptr;
 
+	/*
+	 * spin lock/unlock provide the needed smp_mb() before/after
+	 */
 	atomic_ops_lock(flags);
 	prev = *p;
 	if (prev == expected)
@@ -77,12 +90,16 @@ static inline unsigned long __xchg(unsig
 
 	switch (size) {
 	case 4:
+		smp_mb();
+
 		__asm__ __volatile__(
 		"	ex  %0, [%1]	\n"
 		: "+r"(val)
 		: "r"(ptr)
 		: "memory");
 
+		smp_mb();
+
 		return val;
 	}
 	return __xchg_bad_pointer();
arch/arc/include/asm/spinlock.h +32 -0
@@ -22,24 +22,46 @@ static inline void arch_spin_lock(arch_s
 {
 	unsigned int tmp = __ARCH_SPIN_LOCK_LOCKED__;
 
+	/*
+	 * This smp_mb() is technically superfluous, we only need the one
+	 * after the lock for providing the ACQUIRE semantics.
+	 * However doing the "right" thing was regressing hackbench
+	 * so keeping this, pending further investigation
+	 */
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	ex  %0, [%1]		\n"
 	"	breq  %0, %2, 1b	\n"
 	: "+&r" (tmp)
 	: "r"(&(lock->slock)), "ir"(__ARCH_SPIN_LOCK_LOCKED__)
 	: "memory");
+
+	/*
+	 * ACQUIRE barrier to ensure load/store after taking the lock
+	 * don't "bleed-up" out of the critical section (leak-in is allowed)
+	 * http://www.spinics.net/lists/kernel/msg2010409.html
+	 *
+	 * ARCv2 only has load-load, store-store and all-all barrier
+	 * thus need the full all-all barrier
+	 */
+	smp_mb();
 }
 
 static inline int arch_spin_trylock(arch_spinlock_t *lock)
 {
 	unsigned int tmp = __ARCH_SPIN_LOCK_LOCKED__;
 
+	smp_mb();
+
 	__asm__ __volatile__(
 	"1:	ex  %0, [%1]		\n"
 	: "+r" (tmp)
 	: "r"(&(lock->slock))
 	: "memory");
 
+	smp_mb();
+
 	return (tmp == __ARCH_SPIN_LOCK_UNLOCKED__);
 }
 
@@ -47,12 +69,22 @@ static inline void arch_spin_unlock(arch
 {
 	unsigned int tmp = __ARCH_SPIN_LOCK_UNLOCKED__;
 
+	/*
+	 * RELEASE barrier: given the instructions avail on ARCv2, full barrier
+	 * is the only option
+	 */
+	smp_mb();
+
 	__asm__ __volatile__(
 	"	ex  %0, [%1]		\n"
 	: "+r" (tmp)
 	: "r"(&(lock->slock))
 	: "memory");
 
+	/*
+	 * superfluous, but keeping for now - see pairing version in
+	 * arch_spin_lock above
+	 */
 	smp_mb();
 }
 
author maintainer
#24 lore raw

PATCH 24/58 ARC: add compiler barrier to LLSC based cmpxchg

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vineet Gupta <[email protected]>

commit d57f727264f1425a94689bafc7e99e502cb135b5 upstream.

When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs.

|	do {
|		new = old = *ipi_data_ptr;
|		new |= 1U << msg;
|	} while (cmpxchg(ipi_data_ptr, old, new) != old);

was generating to below

| 8015cef8:	ld         r2,[r4,0]  <-- First LD
| 8015cefc:	bset       r1,r2,r1
|
| 8015cf00:	llock      r3,[r4]  <-- atomic op
| 8015cf04:	brne       r3,r2,8015cf10
| 8015cf08:	scond      r1,[r4]
| 8015cf0c:	bnz        8015cf00
|
| 8015cf10:	brne       r3,r2,8015cf00  <-- Branch doesn't go to orig LD

Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg

---
 arch/arc/include/asm/cmpxchg.h |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
arch/arc/include/asm/cmpxchg.h +5 -4
@@ -33,10 +33,11 @@ __cmpxchg(volatile void *ptr, unsigned l
 	"	scond   %3, [%1]	\n"
 	"	bnz     1b		\n"
 	"2:				\n"
-	: "=&r"(prev)
-	: "r"(ptr), "ir"(expected),
-	  "r"(new) /* can't be "ir". scond can't take limm for "b" */
-	: "cc");
+	: "=&r"(prev)	/* Early clobber, to prevent reg reuse */
+	: "r"(ptr),	/* Not "m": llock only supports reg direct addr mode */
+	  "ir"(expected),
+	  "r"(new)	/* can't be "ir". scond can't take LIMM for "b" */
+	: "cc", "memory"); /* so that gcc knows memory is being written here */
 
 	smp_mb();
 
author maintainer
#25 lore raw

PATCH 25/58 mei: me: wait for power gating exit confirmation

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexander Usyskin <[email protected]>

commit 3dc196eae1db548f05e53e5875ff87b8ff79f249 upstream.

Fix the hbm power gating state machine so it will wait till it receives confirmation interrupt for the PG_ISOLATION_EXIT message.

In process of the suspend flow the devices first have to exit from the power gating state (runtime pm resume).
If we do not handle the confirmation interrupt after sending PG_ISOLATION_EXIT message, we may receive it already after the suspend flow has changed the device state and interrupt will be interpreted as a spurious event, consequently link reset will be invoked which will prevent the device from completing the suspend flow

kernel: [6603] mei_reset:136: mei_me 0000:00:16.0: powering down: end of reset
kernel: [476] mei_me_irq_thread_handler:643: mei_me 0000:00:16.0: function called after ISR to handle the interrupt processing.
kernel: mei_me 0000:00:16.0: FW not ready: resetting

---
 drivers/misc/mei/client.c  |    2 -
 drivers/misc/mei/hw-me.c   |   59 +++++++++++++++++++++++++++++++++++++++++----
 drivers/misc/mei/hw-txe.c  |   13 +++++++++
 drivers/misc/mei/mei_dev.h |   11 ++++++++
 4 files changed, 80 insertions(+), 5 deletions(-)
drivers/misc/mei/client.c +1 -1
@@ -573,7 +573,7 @@ void mei_host_client_init(struct work_st
 bool mei_hbuf_acquire(struct mei_device *dev)
 {
 	if (mei_pg_state(dev) == MEI_PG_ON ||
-	    dev->pg_event == MEI_PG_EVENT_WAIT) {
+	    mei_pg_in_transition(dev)) {
 		dev_dbg(dev->dev, "device is in pg\n");
 		return false;
 	}
drivers/misc/mei/hw-me.c +55 -4

99 lines not on this page · raw message

drivers/misc/mei/hw-txe.c +13 -0
@@ -302,6 +302,18 @@ int mei_txe_aliveness_set_sync(struct me
 }
 
 /**
+ * mei_txe_pg_in_transition - is device now in pg transition
+ *
+ * @dev: the device structure
+ *
+ * Return: true if in pg transition, false otherwise
+ */
+static bool mei_txe_pg_in_transition(struct mei_device *dev)
+{
+	return dev->pg_event == MEI_PG_EVENT_WAIT;
+}
+
+/**
  * mei_txe_pg_is_enabled - detect if PG is supported by HW
  *
  * @dev: the device structure
@@ -1138,6 +1150,7 @@ static const struct mei_hw_ops mei_txe_h
 	.hw_config = mei_txe_hw_config,
 	.hw_start = mei_txe_hw_start,
 
+	.pg_in_transition = mei_txe_pg_in_transition,
 	.pg_is_enabled = mei_txe_pg_is_enabled,
 
 	.intr_clear = mei_txe_intr_clear,
drivers/misc/mei/mei_dev.h +11 -0
@@ -269,6 +269,7 @@ struct mei_cl {
 
  * @fw_status        : get fw status registers
  * @pg_state         : power gating state of the device
+ * @pg_in_transition : is device now in pg transition
  * @pg_is_enabled    : is power gating enabled
 
  * @intr_clear       : clear pending interrupts
@@ -298,6 +299,7 @@ struct mei_hw_ops {
 
 	int (*fw_status)(struct mei_device *dev, struct mei_fw_status *fw_sts);
 	enum mei_pg_state (*pg_state)(struct mei_device *dev);
+	bool (*pg_in_transition)(struct mei_device *dev);
 	bool (*pg_is_enabled)(struct mei_device *dev);
 
 	void (*intr_clear)(struct mei_device *dev);
@@ -396,11 +398,15 @@ struct mei_cl_device {
  * @MEI_PG_EVENT_IDLE: the driver is not in power gating transition
  * @MEI_PG_EVENT_WAIT: the driver is waiting for a pg event to complete
  * @MEI_PG_EVENT_RECEIVED: the driver received pg event
+ * @MEI_PG_EVENT_INTR_WAIT: the driver is waiting for a pg event interrupt
+ * @MEI_PG_EVENT_INTR_RECEIVED: the driver received pg event interrupt
  */
 enum mei_pg_event {
 	MEI_PG_EVENT_IDLE,
 	MEI_PG_EVENT_WAIT,
 	MEI_PG_EVENT_RECEIVED,
+	MEI_PG_EVENT_INTR_WAIT,
+	MEI_PG_EVENT_INTR_RECEIVED,
 };
 
 /**
@@ -727,6 +733,11 @@ static inline enum mei_pg_state mei_pg_s
 	return dev->ops->pg_state(dev);
 }
 
+static inline bool mei_pg_in_transition(struct mei_device *dev)
+{
+	return dev->ops->pg_in_transition(dev);
+}
+
 static inline bool mei_pg_is_enabled(struct mei_device *dev)
 {
 	return dev->ops->pg_is_enabled(dev);
author maintainer
#26 lore raw

PATCH 26/58 mei: txe: reduce suspend/resume time

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tomas Winkler <[email protected]>

commit fe292283c23329218e384bffc6cb4bfa3fd92277 upstream.

HW has to be in known state before the initialisation sequence is started. The polling step for settling aliveness was set to 200ms while in practise this can be done in up to 30msecs.

---
 drivers/misc/mei/hw-txe.c |   20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)
drivers/misc/mei/hw-txe.c +10 -10
@@ -16,6 +16,7 @@
 
 #include <linux/pci.h>
 #include <linux/jiffies.h>
+#include <linux/ktime.h>
 #include <linux/delay.h>
 #include <linux/kthread.h>
 #include <linux/irqreturn.h>
@@ -218,26 +219,25 @@ static u32 mei_txe_aliveness_get(struct
  *
  * Polls for HICR_HOST_ALIVENESS_RESP.ALIVENESS_RESP to be set
  *
- * Return: > 0 if the expected value was received, -ETIME otherwise
+ * Return: 0 if the expected value was received, -ETIME otherwise
  */
 static int mei_txe_aliveness_poll(struct mei_device *dev, u32 expected)
 {
 	struct mei_txe_hw *hw = to_txe_hw(dev);
-	int t = 0;
+	ktime_t stop, start;
 
+	start = ktime_get();
+	stop = ktime_add(start, ms_to_ktime(SEC_ALIVENESS_WAIT_TIMEOUT));
 	do {
 		hw->aliveness = mei_txe_aliveness_get(dev);
 		if (hw->aliveness == expected) {
 			dev->pg_event = MEI_PG_EVENT_IDLE;
-			dev_dbg(dev->dev,
-				"aliveness settled after %d msecs\n", t);
-			return t;
+			dev_dbg(dev->dev, "aliveness settled after %lld usecs\n",
+				ktime_to_us(ktime_sub(ktime_get(), start)));
+			return 0;
 		}
-		mutex_unlock(&dev->device_lock);
-		msleep(MSEC_PER_SEC / 5);
-		mutex_lock(&dev->device_lock);
-		t += MSEC_PER_SEC / 5;
-	} while (t < SEC_ALIVENESS_WAIT_TIMEOUT);
+		usleep_range(20, 50);
+	} while (ktime_before(ktime_get(), stop));
 
 	dev->pg_event = MEI_PG_EVENT_IDLE;
 	dev_err(dev->dev, "aliveness timed out\n");
author maintainer
#27 lore raw

PATCH 27/58 arm64: Do not attempt to use init_mm in reset_context()

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Catalin Marinas <[email protected]>

commit 565630d503ef24e44c252bed55571b3a0d68455f upstream.

After secondary CPU boot or hotplug, the active_mm of the idle thread is &init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1 and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the TTBR0_EL1 is already set to the reserved value, there is no need to perform any context reset.

---
 arch/arm64/mm/context.c |    8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/mm/context.c +8 -0
@@ -92,6 +92,14 @@ static void reset_context(void *info)
 	unsigned int cpu = smp_processor_id();
 	struct mm_struct *mm = current->active_mm;
 
+	/*
+	 * current->active_mm could be init_mm for the idle thread immediately
+	 * after secondary CPU boot or hotplug. TTBR0_EL1 is already set to
+	 * the reserved value, so no need to reset any context.
+	 */
+	if (mm == &init_mm)
+		return;
+
 	smp_rmb();
 	asid = cpu_last_asid + cpu;
 
author maintainer
#28 lore raw

PATCH 28/58 arm64: entry: fix context tracking for el0_sp_pc

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mark Rutland <[email protected]>

commit 46b0567c851cf85d6ba6f23eef385ec9111d09bc upstream.

Commit 6c81fe7925cc4c42 ("arm64: enable context tracking") did not update el0_sp_pc to use ct_user_exit, but this appears to have been unintentional. In commit 6ab6463aeb5fbc75 ("arm64: adjust el0_sync so that a function can be called") we made x0 available, and in the return to userspace we call ct_user_enter in the kernel_exit macro.

Due to this, we currently don't correctly inform RCU of the user->kernel transition, and may erroneously account for time spent in the kernel as if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING is enabled.

As we do record the kernel->user transition, a userspace application making accesses from an unaligned stack pointer can demonstrate the imbalance, provoking the following warning:

------------[ cut here ]------------
WARNING: CPU: 2 PID: 3660 at kernel/context_tracking.c:75 context_tracking_enter+0xd8/0xe4()
Modules linked in:
CPU: 2 PID: 3660 Comm: a.out Not tainted 4.1.0-rc7+ #8
Hardware name: ARM Juno development board (r0) (DT)
Call trace:
[<ffffffc000089914>] dump_backtrace+0x0/0x124
[<ffffffc000089a48>] show_stack+0x10/0x1c
[<ffffffc0005b3cbc>] dump_stack+0x84/0xc8
[<ffffffc0000b3214>] warn_slowpath_common+0x98/0xd0
[<ffffffc0000b330c>] warn_slowpath_null+0x14/0x20
[<ffffffc00013ada4>] context_tracking_enter+0xd4/0xe4
[<ffffffc0005b534c>] preempt_schedule_irq+0xd4/0x114
[<ffffffc00008561c>] el1_preempt+0x4/0x28
[<ffffffc0001b8040>] exit_files+0x38/0x4c
[<ffffffc0000b5b94>] do_exit+0x430/0x978
[<ffffffc0000b614c>] do_group_exit+0x40/0xd4
[<ffffffc0000c0208>] get_signal+0x23c/0x4f4
[<ffffffc0000890b4>] do_signal+0x1ac/0x518
[<ffffffc000089650>] do_notify_resume+0x5c/0x68
---[ end trace 963c192600337066 ]---

This patch adds the missing ct_user_exit to the el0_sp_pc entry path, correcting the context tracking for this case.

Fixes 6c81fe7925cc ("arm64: enable context tracking")
---
 arch/arm64/kernel/entry.S |    1 +
 1 file changed, 1 insertion(+)
arch/arm64/kernel/entry.S +1 -0
@@ -517,6 +517,7 @@ el0_sp_pc:
 	mrs	x26, far_el1
 	// enable interrupts before calling the main handler
 	enable_dbg_and_irq
+	ct_user_exit
 	mov	x0, x26
 	mov	x1, x25
 	mov	x2, sp
author maintainer
#29 lore raw

PATCH 29/58 arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dave P Martin <[email protected]>

commit b9bcc919931611498e856eae9bf66337330d04cc upstream.

The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock.

This may cause memmap entries that are in use to get freed.

In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree.

This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it.

This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used.

---
 arch/arm64/mm/init.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/mm/init.c +1 -1
@@ -260,7 +260,7 @@ static void __init free_unused_memmap(vo
 		 * memmap entries are valid from the bank end aligned to
 		 * MAX_ORDER_NR_PAGES.
 		 */
-		prev_end = ALIGN(start + __phys_to_pfn(reg->size),
+		prev_end = ALIGN(__phys_to_pfn(reg->base + reg->size),
 				 MAX_ORDER_NR_PAGES);
 	}
 
author maintainer
#30 lore raw

PATCH 30/58 arm64: vdso: work-around broken ELF toolchains in Makefile

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 6f1a6ae87c0c60d7c462ef8fd071f291aa7a9abb upstream.

When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted).

The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel.

This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO.

---
 arch/arm64/kernel/vdso/Makefile |    4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/kernel/vdso/Makefile +4 -0
@@ -15,6 +15,10 @@ ccflags-y := -shared -fno-common -fno-bu
 ccflags-y += -nostdlib -Wl,-soname=linux-vdso.so.1 \
 		$(call cc-ldoption, -Wl$(comma)--hash-style=sysv)
 
+# Workaround for bare-metal (ELF) toolchains that neglect to pass -shared
+# down to collect2, resulting in silent corruption of the vDSO image.
+ccflags-y += -Wl,-shared
+
 obj-y += vdso.o
 extra-y += vdso.lds vdso-offsets.h
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
author maintainer
#31 lore raw

PATCH 31/58 mm: kmemleak: allow safe memory scanning during kmemleak disabling

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Catalin Marinas <[email protected]>

commit c5f3b1a51a591c18c8b33983908e7fdda6ae417e upstream.

The kmemleak scanning thread can run for minutes. Callbacks like kmemleak_free() are allowed during this time, the race being taken care of by the object->lock spinlock. Such lock also prevents a memory block from being freed or unmapped while it is being scanned by blocking the kmemleak_free() -> ... -> __delete_object() function until the lock is released in scan_object().

When a kmemleak error occurs (e.g. it fails to allocate its metadata), kmemleak_enabled is set and __delete_object() is no longer called on freed objects. If kmemleak_scan is running at the same time, kmemleak_free() no longer waits for the object scanning to complete, allowing the corresponding memory block to be freed or unmapped (in the case of vfree()). This leads to kmemleak_scan potentially triggering a page fault.

This patch separates the kmemleak_free() enabling/disabling from the overall kmemleak_enabled nob so that we can defer the disabling of the object freeing tracking until the scanning thread completed. The kmemleak_free_part() is deliberately ignored by this patch since this is only called during boot before the scanning thread started.

---
 mm/kmemleak.c |   19 ++++++++++++++++---
 1 file changed, 16 insertions(+), 3 deletions(-)
mm/kmemleak.c +16 -3
@@ -195,6 +195,8 @@ static struct kmem_cache *scan_area_cach
 
 /* set if tracing memory operations is enabled */
 static int kmemleak_enabled;
+/* same as above but only for the kmemleak_free() callback */
+static int kmemleak_free_enabled;
 /* set in the late_initcall if there were no errors */
 static int kmemleak_initialized;
 /* enables or disables early logging of the memory operations */
@@ -942,7 +944,7 @@ void __ref kmemleak_free(const void *ptr
 {
 	pr_debug("%s(0x%p)\n", __func__, ptr);
 
-	if (kmemleak_enabled && ptr && !IS_ERR(ptr))
+	if (kmemleak_free_enabled && ptr && !IS_ERR(ptr))
 		delete_object_full((unsigned long)ptr);
 	else if (kmemleak_early_log)
 		log_early(KMEMLEAK_FREE, ptr, 0, 0);
@@ -982,7 +984,7 @@ void __ref kmemleak_free_percpu(const vo
 
 	pr_debug("%s(0x%p)\n", __func__, ptr);
 
-	if (kmemleak_enabled && ptr && !IS_ERR(ptr))
+	if (kmemleak_free_enabled && ptr && !IS_ERR(ptr))
 		for_each_possible_cpu(cpu)
 			delete_object_full((unsigned long)per_cpu_ptr(ptr,
 								      cpu));
@@ -1750,6 +1752,13 @@ static void kmemleak_do_cleanup(struct w
 	mutex_lock(&scan_mutex);
 	stop_scan_thread();
 
+	/*
+	 * Once the scan thread has stopped, it is safe to no longer track
+	 * object freeing. Ordering of the scan thread stopping and the memory
+	 * accesses below is guaranteed by the kthread_stop() function.
+	 */
+	kmemleak_free_enabled = 0;
+
 	if (!kmemleak_found_leaks)
 		__kmemleak_do_cleanup();
 	else
@@ -1776,6 +1785,8 @@ static void kmemleak_disable(void)
 	/* check whether it is too early for a kernel thread */
 	if (kmemleak_initialized)
 		schedule_work(&cleanup_work);
+	else
+		kmemleak_free_enabled = 0;
 
 	pr_info("Kernel memory leak detector disabled\n");
 }
@@ -1840,8 +1851,10 @@ void __init kmemleak_init(void)
 	if (kmemleak_error) {
 		local_irq_restore(flags);
 		return;
-	} else
+	} else {
 		kmemleak_enabled = 1;
+		kmemleak_free_enabled = 1;
+	}
 	local_irq_restore(flags);
 
 	/*
author maintainer
#32 lore raw

PATCH 32/58 mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Larry Finger <[email protected]>

commit 8a8c35fadfaf55629a37ef1a8ead1b8fb32581d2 upstream.

Beginning at commit d52d3997f843 ("ipv6: Create percpu rt6_info"), the following INFO splat is logged:

===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc7-next-20150612 #1 Not tainted
-------------------------------
kernel/sched/core.c:7318 Illegal context switch in RCU-bh read-side critical section! other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
3 locks held by systemd/1:

   #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815f0c8f>] rtnetlink_rcv+0x1f/0x40
   #1:  (rcu_read_lock_bh){......}, at: [<ffffffff816a34e2>] ipv6_add_addr+0x62/0x540
   #2:  (addrconf_hash_lock){+...+.}, at: [<ffffffff816a3604>] ipv6_add_addr+0x184/0x540
  stack backtrace:
  CPU: 0 PID: 1 Comm: systemd Not tainted 4.1.0-rc7-next-20150612 #1
  Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20   04/17/2014
  Call Trace:
    dump_stack+0x4c/0x6e
    lockdep_rcu_suspicious+0xe7/0x120
    ___might_sleep+0x1d5/0x1f0
    __might_sleep+0x4d/0x90
    kmem_cache_alloc+0x47/0x250
    create_object+0x39/0x2e0
    kmemleak_alloc_percpu+0x61/0xe0
    pcpu_alloc+0x370/0x630

Additional backtrace lines are truncated. In addition, the above splat is followed by several "BUG: sleeping function called from invalid context at mm/slub.c:1268" outputs. As suggested by Martin KaFai Lau, these are the clue to the fix. Routine kmemleak_alloc_percpu() always uses GFP_KERNEL for its allocations, whereas it should follow the gfp from its callers.

---
 include/linux/kmemleak.h |    6 ++++--
 mm/kmemleak.c            |    9 +++++----
 mm/percpu.c              |    2 +-
 3 files changed, 10 insertions(+), 7 deletions(-)
include/linux/kmemleak.h +4 -2
@@ -28,7 +28,8 @@
 extern void kmemleak_init(void) __ref;
 extern void kmemleak_alloc(const void *ptr, size_t size, int min_count,
 			   gfp_t gfp) __ref;
-extern void kmemleak_alloc_percpu(const void __percpu *ptr, size_t size) __ref;
+extern void kmemleak_alloc_percpu(const void __percpu *ptr, size_t size,
+				  gfp_t gfp) __ref;
 extern void kmemleak_free(const void *ptr) __ref;
 extern void kmemleak_free_part(const void *ptr, size_t size) __ref;
 extern void kmemleak_free_percpu(const void __percpu *ptr) __ref;
@@ -71,7 +72,8 @@ static inline void kmemleak_alloc_recurs
 					    gfp_t gfp)
 {
 }
-static inline void kmemleak_alloc_percpu(const void __percpu *ptr, size_t size)
+static inline void kmemleak_alloc_percpu(const void __percpu *ptr, size_t size,
+					 gfp_t gfp)
 {
 }
 static inline void kmemleak_free(const void *ptr)
mm/kmemleak.c +5 -4
@@ -909,12 +909,13 @@ EXPORT_SYMBOL_GPL(kmemleak_alloc);
  * kmemleak_alloc_percpu - register a newly allocated __percpu object
  * @ptr:	__percpu pointer to beginning of the object
  * @size:	size of the object
+ * @gfp:	flags used for kmemleak internal memory allocations
  *
  * This function is called from the kernel percpu allocator when a new object
- * (memory block) is allocated (alloc_percpu). It assumes GFP_KERNEL
- * allocation.
+ * (memory block) is allocated (alloc_percpu).
  */
-void __ref kmemleak_alloc_percpu(const void __percpu *ptr, size_t size)
+void __ref kmemleak_alloc_percpu(const void __percpu *ptr, size_t size,
+				 gfp_t gfp)
 {
 	unsigned int cpu;
 
@@ -927,7 +928,7 @@ void __ref kmemleak_alloc_percpu(const v
 	if (kmemleak_enabled && ptr && !IS_ERR(ptr))
 		for_each_possible_cpu(cpu)
 			create_object((unsigned long)per_cpu_ptr(ptr, cpu),
-				      size, 0, GFP_KERNEL);
+				      size, 0, gfp);
 	else if (kmemleak_early_log)
 		log_early(KMEMLEAK_ALLOC_PERCPU, ptr, size, 0);
 }
mm/percpu.c +1 -1
@@ -1030,7 +1030,7 @@ area_found:
 		memset((void *)pcpu_chunk_addr(chunk, cpu, 0) + off, 0, size);
 
 	ptr = __addr_to_pcpu_ptr(chunk->base_addr + off);
-	kmemleak_alloc_percpu(ptr, size);
+	kmemleak_alloc_percpu(ptr, size, gfp);
 	return ptr;
 
 fail_unlock:
author maintainer
#33 lore raw

PATCH 33/58 mm, thp: respect MPOL_PREFERRED policy with non-local node

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vlastimil Babka <[email protected]>

commit 0867a57c4f80a566dda1bac975b42fcd857cb489 upstream.

Since commit 077fcf116c8c ("mm/thp: allocate transparent hugepages on local node"), we handle THP allocations on page fault in a special way - for non-interleave memory policies, the allocation is only attempted on the node local to the current CPU, if the policy's nodemask allows the node.

This is motivated by the assumption that THP benefits cannot offset the cost of remote accesses, so it's better to fallback to base pages on the local node (which might still be available, while huge pages are not due to fragmentation) than to allocate huge pages on a remote node.

The nodemask check prevents us from violating e.g. MPOL_BIND policies where the local node is not among the allowed nodes. However, the current implementation can still give surprising results for the MPOL_PREFERRED policy when the preferred node is different than the current CPU's local node.

In such case we should honor the preferred node and not use the local node, which is what this patch does. If hugepage allocation on the preferred node fails, we fall back to base pages and don't try other nodes, with the same motivation as is done for the local node hugepage allocations. The patch also moves the MPOL_INTERLEAVE check around to simplify the hugepage specific test.

The difference can be demonstrated using in-tree transhuge-stress test on the following 2-node machine where half memory on one node was occupied to show the difference.

Quoted 1 line

numactl --hardware

available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 24 25 26 27 28 29 30 31 32 33 34 35 node 0 size: 7878 MB
node 0 free: 3623 MB
node 1 cpus: 12 13 14 15 16 17 18 19 20 21 22 23 36 37 38 39 40 41 42 43 44 45 46 47 node 1 size: 8045 MB
node 1 free: 7818 MB
node distances:
node 0 1

  0:  10  21
  1:  21  10

Before the patch:

Quoted 1 line

numactl -p0 -C0 ./transhuge-stress

transhuge-stress: 2.197 s/loop, 0.276 ms/page, 7249.168 MiB/s 7962 succeed, 0 failed, 1786 different pages

Quoted 1 line

numactl -p0 -C12 ./transhuge-stress

transhuge-stress: 2.962 s/loop, 0.372 ms/page, 5376.172 MiB/s 7962 succeed, 0 failed, 3873 different pages

Number of successful THP allocations corresponds to free memory on node 0 in the first case and node 1 in the second case, i.e. -p parameter is ignored and cpu binding "wins".

After the patch:

Quoted 1 line

numactl -p0 -C0 ./transhuge-stress

transhuge-stress: 2.183 s/loop, 0.274 ms/page, 7295.516 MiB/s 7962 succeed, 0 failed, 1760 different pages

Quoted 1 line

numactl -p0 -C12 ./transhuge-stress

transhuge-stress: 2.878 s/loop, 0.361 ms/page, 5533.638 MiB/s 7962 succeed, 0 failed, 1750 different pages

Quoted 1 line

numactl -p1 -C0 ./transhuge-stress

transhuge-stress: 4.628 s/loop, 0.581 ms/page, 3440.893 MiB/s 7962 succeed, 0 failed, 3918 different pages

The -p parameter is respected regardless of cpu binding.

Quoted 1 line

numactl -C0 ./transhuge-stress

transhuge-stress: 2.202 s/loop, 0.277 ms/page, 7230.003 MiB/s 7962 succeed, 0 failed, 1750 different pages

Quoted 1 line

numactl -C12 ./transhuge-stress

transhuge-stress: 3.020 s/loop, 0.379 ms/page, 5273.324 MiB/s 7962 succeed, 0 failed, 3916 different pages

Without -p parameter, hugepage restriction to CPU-local node works as before.

Fixes 077fcf116c8c ("mm/thp: allocate transparent hugepages on local node")
Cc Aneesh Kumar K.V <[email protected]>
Cc Kirill A. Shutemov <[email protected]>
Cc Andrea Arcangeli <[email protected]>
Cc Michal Hocko <[email protected]>
---
 mm/mempolicy.c |   38 ++++++++++++++++++++++----------------
 1 file changed, 22 insertions(+), 16 deletions(-)
mm/mempolicy.c +22 -16
@@ -1971,35 +1971,41 @@ retry_cpuset:
 	pol = get_vma_policy(vma, addr);
 	cpuset_mems_cookie = read_mems_allowed_begin();
 
-	if (unlikely(IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) && hugepage &&
-					pol->mode != MPOL_INTERLEAVE)) {
+	if (pol->mode == MPOL_INTERLEAVE) {
+		unsigned nid;
+
+		nid = interleave_nid(pol, vma, addr, PAGE_SHIFT + order);
+		mpol_cond_put(pol);
+		page = alloc_page_interleave(gfp, order, nid);
+		goto out;
+	}
+
+	if (unlikely(IS_ENABLED(CONFIG_TRANSPARENT_HUGEPAGE) && hugepage)) {
+		int hpage_node = node;
+
 		/*
 		 * For hugepage allocation and non-interleave policy which
-		 * allows the current node, we only try to allocate from the
-		 * current node and don't fall back to other nodes, as the
-		 * cost of remote accesses would likely offset THP benefits.
+		 * allows the current node (or other explicitly preferred
+		 * node) we only try to allocate from the current/preferred
+		 * node and don't fall back to other nodes, as the cost of
+		 * remote accesses would likely offset THP benefits.
 		 *
 		 * If the policy is interleave, or does not allow the current
 		 * node in its nodemask, we allocate the standard way.
 		 */
+		if (pol->mode == MPOL_PREFERRED &&
+						!(pol->flags & MPOL_F_LOCAL))
+			hpage_node = pol->v.preferred_node;
+
 		nmask = policy_nodemask(gfp, pol);
-		if (!nmask || node_isset(node, *nmask)) {
+		if (!nmask || node_isset(hpage_node, *nmask)) {
 			mpol_cond_put(pol);
-			page = alloc_pages_exact_node(node,
+			page = alloc_pages_exact_node(hpage_node,
 						gfp | __GFP_THISNODE, order);
 			goto out;
 		}
 	}
 
-	if (pol->mode == MPOL_INTERLEAVE) {
-		unsigned nid;
-
-		nid = interleave_nid(pol, vma, addr, PAGE_SHIFT + order);
-		mpol_cond_put(pol);
-		page = alloc_page_interleave(gfp, order, nid);
-		goto out;
-	}
-
 	nmask = policy_nodemask(gfp, pol);
 	zl = policy_zonelist(gfp, pol, node);
 	mpol_cond_put(pol);
author maintainer
#34 lore raw

PATCH 34/58 iser-target: release stale iser connections

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sagi Grimberg <[email protected]>

commit 2f1b6b7d9a815f341b18dfd26a363f37d4d3c96a upstream.

When receiving a new iser connect request we serialize the pending requests by adding the newly created iser connection to the np accept list and let the login thread process the connect request one by one (np_accept_wait).

In case we received a disconnect request before the iser_conn has begun processing (still linked in np_accept_list) we should detach it from the list and clean it up and not have the login thread process a stale connection. We do it only when the connection state is not already terminating (initiator driven disconnect) as this might lead us to access np_accept_mutex after the np was released in live shutdown scenarios.

---
 drivers/infiniband/ulp/isert/ib_isert.c |   18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)
drivers/infiniband/ulp/isert/ib_isert.c +17 -1
@@ -65,6 +65,8 @@ static int
 isert_rdma_accept(struct isert_conn *isert_conn);
 struct rdma_cm_id *isert_setup_id(struct isert_np *isert_np);
 
+static void isert_release_work(struct work_struct *work);
+
 static inline bool
 isert_prot_cmd(struct isert_conn *conn, struct se_cmd *cmd)
 {
@@ -604,6 +606,7 @@ isert_connect_request(struct rdma_cm_id
 	mutex_init(&isert_conn->conn_mutex);
 	spin_lock_init(&isert_conn->conn_lock);
 	INIT_LIST_HEAD(&isert_conn->conn_fr_pool);
+	INIT_WORK(&isert_conn->release_work, isert_release_work);
 
 	isert_conn->conn_cm_id = cma_id;
 
@@ -863,6 +866,7 @@ isert_disconnected_handler(struct rdma_c
 {
 	struct isert_np *isert_np = cma_id->context;
 	struct isert_conn *isert_conn;
+	bool terminating = false;
 
 	if (isert_np->np_cm_id == cma_id)
 		return isert_np_cma_handler(cma_id->context, event);
@@ -870,12 +874,25 @@ isert_disconnected_handler(struct rdma_c
 	isert_conn = cma_id->qp->qp_context;
 
 	mutex_lock(&isert_conn->conn_mutex);
+	terminating = (isert_conn->state == ISER_CONN_TERMINATING);
 	isert_conn_terminate(isert_conn);
 	mutex_unlock(&isert_conn->conn_mutex);
 
 	isert_info("conn %p completing conn_wait\n", isert_conn);
 	complete(&isert_conn->conn_wait);
 
+	if (terminating)
+		goto out;
+
+	mutex_lock(&isert_np->np_accept_mutex);
+	if (!list_empty(&isert_conn->conn_accept_node)) {
+		list_del_init(&isert_conn->conn_accept_node);
+		isert_put_conn(isert_conn);
+		queue_work(isert_release_wq, &isert_conn->release_work);
+	}
+	mutex_unlock(&isert_np->np_accept_mutex);
+
+out:
 	return 0;
 }
 
@@ -3305,7 +3322,6 @@ static void isert_wait_conn(struct iscsi
 	isert_wait4flush(isert_conn);
 	isert_wait4logout(isert_conn);
 
-	INIT_WORK(&isert_conn->release_work, isert_release_work);
 	queue_work(isert_release_wq, &isert_conn->release_work);
 }
 
author maintainer
#35 lore raw

PATCH 35/58 regmap: Fix regmap_bulk_read in BE mode

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arun Chandran <[email protected]>

commit 15b8d2c41fe5839582029f65c5f7004db451cc2b upstream.

In big endian mode regmap_bulk_read gives incorrect data for byte reads.

This is because memcpy of a single byte from an address after full word read gives different results when endianness differs. ie. we get little-end in LE and big-end in BE.

---
 drivers/base/regmap/regmap.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/base/regmap/regmap.c +1 -1
@@ -2318,7 +2318,7 @@ int regmap_bulk_read(struct regmap *map,
 					  &ival);
 			if (ret != 0)
 				return ret;
-			memcpy(val + (i * val_bytes), &ival, val_bytes);
+			map->format.format_val(val + (i * val_bytes), ival, 0);
 		}
 	}
 
author maintainer
#36 lore raw

PATCH 36/58 regmap: Fix possible shift overflow in regmap_field_init()

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Maxime Coquelin <[email protected]>

commit 921cc29473a0d7c109105c1876ddb432f4a4be7d upstream.

The way the mask is generated in regmap_field_init() is wrong. Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift overflow while calculating the mask field.

On some 32 bits architectures, such as x86, the generated mask is 0, instead of the expected 0xffffffff.

This patch uses GENMASK() to fix the problem, as this macro is already safe regarding shift overflow.

---
 drivers/base/regmap/regmap.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/base/regmap/regmap.c +1 -2
@@ -945,11 +945,10 @@ EXPORT_SYMBOL_GPL(devm_regmap_init);
 static void regmap_field_init(struct regmap_field *rm_field,
 	struct regmap *regmap, struct reg_field reg_field)
 {
-	int field_bits = reg_field.msb - reg_field.lsb + 1;
 	rm_field->regmap = regmap;
 	rm_field->reg = reg_field.reg;
 	rm_field->shift = reg_field.lsb;
-	rm_field->mask = ((BIT(field_bits) - 1) << reg_field.lsb);
+	rm_field->mask = GENMASK(reg_field.msb, reg_field.lsb);
 	rm_field->id_size = reg_field.id_size;
 	rm_field->id_offset = reg_field.id_offset;
 }
author maintainer
#37 lore raw

PATCH 37/58 regulator: max77686: fix gpio_enabled shift wrapping bug

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Joe Perches <[email protected]>

commit c53403a37cf083ce85da720f18918f73580d0064 upstream.

The code should handle more than 32 bits here because "id" can be a value up to MAX77686_REGULATORS (currently 34).

Convert the gpio_enabled type to DECLARE_BITMAP and use test_bit/set_bit.

Fixes 3307e9025d29 ("regulator: max77686: Add GPIO control")
---
 drivers/regulator/max77686.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/regulator/max77686.c +3 -3
@@ -88,7 +88,7 @@ enum max77686_ramp_rate {
 };
 
 struct max77686_data {
-	u64 gpio_enabled:MAX77686_REGULATORS;
+	DECLARE_BITMAP(gpio_enabled, MAX77686_REGULATORS);
 
 	/* Array indexed by regulator id */
 	unsigned int opmode[MAX77686_REGULATORS];
@@ -121,7 +121,7 @@ static unsigned int max77686_map_normal_
 	case MAX77686_BUCK8:
 	case MAX77686_BUCK9:
 	case MAX77686_LDO20 ... MAX77686_LDO22:
-		if (max77686->gpio_enabled & (1 << id))
+		if (test_bit(id, max77686->gpio_enabled))
 			return MAX77686_GPIO_CONTROL;
 	}
 
@@ -277,7 +277,7 @@ static int max77686_of_parse_cb(struct d
 	}
 
 	if (gpio_is_valid(config->ena_gpio)) {
-		max77686->gpio_enabled |= (1 << desc->id);
+		set_bit(desc->id, max77686->gpio_enabled);
 
 		return regmap_update_bits(config->regmap, desc->enable_reg,
 					  desc->enable_mask,
author maintainer
#38 lore raw

PATCH 38/58 regulator: core: fix constraints output buffer

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Wahren <[email protected]>

commit a7068e3932eee8268c4ce4e080a338ee7b8a27bf upstream.

The buffer for condtraints debug isn't big enough to hold the output in all cases. So fix this issue by increasing the buffer.

---
 drivers/regulator/core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/regulator/core.c +1 -1
@@ -770,7 +770,7 @@ static int suspend_prepare(struct regula
 static void print_constraints(struct regulator_dev *rdev)
 {
 	struct regulation_constraints *constraints = rdev->constraints;
-	char buf[80] = "";
+	char buf[160] = "";
 	int count = 0;
 	int ret;
 
author maintainer
#39 lore raw

PATCH 39/58 livepatch: add module locking around kallsyms calls

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Miroslav Benes <[email protected]>

commit 9a1bd63cdae4b623494c4ebaf723a91c35ec49fb upstream.

The list of loaded modules is walked through in module_kallsyms_on_each_symbol (called by kallsyms_on_each_symbol). The module_mutex lock should be acquired to prevent potential corruptions in the list.

This was uncovered with new lockdep asserts in module code introduced by the commit 0be964be0d45 ("module: Sanitize RCU usage and locking") in recent next- trees.

---
 kernel/livepatch/core.c |   18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
kernel/livepatch/core.c +13 -5
@@ -179,7 +179,9 @@ static int klp_find_object_symbol(const
 		.count = 0
 	};
 
+	mutex_lock(&module_mutex);
 	kallsyms_on_each_symbol(klp_find_callback, &args);
+	mutex_unlock(&module_mutex);
 
 	if (args.count == 0)
 		pr_err("symbol '%s' not found in symbol table\n", name);
@@ -219,13 +221,19 @@ static int klp_verify_vmlinux_symbol(con
 		.name = name,
 		.addr = addr,
 	};
+	int ret;
 
-	if (kallsyms_on_each_symbol(klp_verify_callback, &args))
-		return 0;
+	mutex_lock(&module_mutex);
+	ret = kallsyms_on_each_symbol(klp_verify_callback, &args);
+	mutex_unlock(&module_mutex);
+
+	if (!ret) {
+		pr_err("symbol '%s' not found at specified address 0x%016lx, kernel mismatch?\n",
+			name, addr);
+		return -EINVAL;
+	}
 
-	pr_err("symbol '%s' not found at specified address 0x%016lx, kernel mismatch?\n",
-		name, addr);
-	return -EINVAL;
+	return 0;
 }
 
 static int klp_find_verify_func_addr(struct klp_object *obj,
author maintainer
#40 lore raw

PATCH 41/58 spi: orion: Fix maximum baud rates for Armada 370/XP

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Gregory CLEMENT <[email protected]>

commit ce2f6ea1cbd41d78224f703af980a6ceeb0eb56a upstream.

The commit df59fa7f4bca "spi: orion: support armada extended baud rates" was too optimistic for the maximum baud rate that the Armada SoCs can support. According to the hardware datasheet the maximum frequency supported by the Armada 370 SoC is tclk/4. But for the Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and for the Armada 375 it is tclk/15.

Currently the armada-370-spi compatible is only used by the Armada 370 and the Armada XP device tree. On Armada 370, tclk cannot be higher than 200MHz. In order to be able to handle both SoCs, we can take the minimum of 50MHz and tclk/4.

A proper solution is adding a compatible string for each SoC, but it can't be done as a fix for compatibility reason (we can't modify device tree that have been already released) and it will be part of a separate patch.

Fixes df59fa7f4bca (spi: orion: support armada extended baud rates)
---
 drivers/spi/spi-orion.c |   25 +++++++++++++++++++++++--
 1 file changed, 23 insertions(+), 2 deletions(-)
drivers/spi/spi-orion.c +23 -2
@@ -61,6 +61,12 @@ enum orion_spi_type {
 
 struct orion_spi_dev {
 	enum orion_spi_type	typ;
+	/*
+	 * min_divisor and max_hz should be exclusive, the only we can
+	 * have both is for managing the armada-370-spi case with old
+	 * device tree
+	 */
+	unsigned long		max_hz;
 	unsigned int		min_divisor;
 	unsigned int		max_divisor;
 	u32			prescale_mask;
@@ -387,8 +393,9 @@ static const struct orion_spi_dev orion_
 
 static const struct orion_spi_dev armada_spi_dev_data = {
 	.typ = ARMADA_SPI,
-	.min_divisor = 1,
+	.min_divisor = 4,
 	.max_divisor = 1920,
+	.max_hz = 50000000,
 	.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
 };
 
@@ -454,7 +461,21 @@ static int orion_spi_probe(struct platfo
 		goto out;
 
 	tclk_hz = clk_get_rate(spi->clk);
-	master->max_speed_hz = DIV_ROUND_UP(tclk_hz, devdata->min_divisor);
+
+	/*
+	 * With old device tree, armada-370-spi could be used with
+	 * Armada XP, however for this SoC the maximum frequency is
+	 * 50MHz instead of tclk/4. On Armada 370, tclk cannot be
+	 * higher than 200MHz. So, in order to be able to handle both
+	 * SoCs, we can take the minimum of 50MHz and tclk/4.
+	 */
+	if (of_device_is_compatible(pdev->dev.of_node,
+					"marvell,armada-370-spi"))
+		master->max_speed_hz = min(devdata->max_hz,
+				DIV_ROUND_UP(tclk_hz, devdata->min_divisor));
+	else
+		master->max_speed_hz =
+			DIV_ROUND_UP(tclk_hz, devdata->min_divisor);
 	master->min_speed_hz = DIV_ROUND_UP(tclk_hz, devdata->max_divisor);
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
author maintainer
#41 lore raw

PATCH 42/58 spi: pl022: Specify num-cs property as required in devicetree binding

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ezequiel Garcia <[email protected]>

commit ea6055c46eda1e19e02209814955e13f334bbe1b upstream.

Since commit 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data") the 'num-cs' parameter cannot be passed through platform data when probing with devicetree. Instead, it's a required devicetree property.

Fix the binding documentation so the property is properly specified.

Fixes 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data")
---
 Documentation/devicetree/bindings/spi/spi_pl022.txt |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/devicetree/bindings/spi/spi_pl022.txt +1 -1
@@ -4,9 +4,9 @@ Required properties:
 - compatible : "arm,pl022", "arm,primecell"
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain SPI controller interrupt
+- num-cs : total number of chipselects
 
 Optional properties:
-- num-cs : total number of chipselects
 - cs-gpios : should specify GPIOs used for chipselects.
   The gpios will be referred to as reg = <index> in the SPI child nodes.
   If unspecified, a single SPI device without a chip select can be used.
author maintainer
#42 lore raw

PATCH 43/58 scsi_transport_srp: Introduce srp_wait_for_queuecommand()

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit be34c62ddf39d1931780b07a6f4241393e4ba2ee upstream.

Introduce the helper function srp_wait_for_queuecommand(). Move the definition of scsi_request_fn_active(). Add a comment above srp_wait_for_queuecommand() that support for scsi-mq needs to be added.

This patch does not change any functionality. A second call to srp_wait_for_queuecommand() will be introduced in the next patch.

Cc James Bottomley <[email protected]>
Cc Sagi Grimberg <[email protected]>
Cc Sebastian Parschauer <[email protected]>
---
 drivers/scsi/scsi_transport_srp.c |   54 +++++++++++++++++++++-----------------
 1 file changed, 31 insertions(+), 23 deletions(-)
drivers/scsi/scsi_transport_srp.c +31 -23
@@ -396,6 +396,36 @@ static void srp_reconnect_work(struct wo
 	}
 }
 
+/**
+ * scsi_request_fn_active() - number of kernel threads inside scsi_request_fn()
+ * @shost: SCSI host for which to count the number of scsi_request_fn() callers.
+ *
+ * To do: add support for scsi-mq in this function.
+ */
+static int scsi_request_fn_active(struct Scsi_Host *shost)
+{
+	struct scsi_device *sdev;
+	struct request_queue *q;
+	int request_fn_active = 0;
+
+	shost_for_each_device(sdev, shost) {
+		q = sdev->request_queue;
+
+		spin_lock_irq(q->queue_lock);
+		request_fn_active += q->request_fn_active;
+		spin_unlock_irq(q->queue_lock);
+	}
+
+	return request_fn_active;
+}
+
+/* Wait until ongoing shost->hostt->queuecommand() calls have finished. */
+static void srp_wait_for_queuecommand(struct Scsi_Host *shost)
+{
+	while (scsi_request_fn_active(shost))
+		msleep(20);
+}
+
 static void __rport_fail_io_fast(struct srp_rport *rport)
 {
 	struct Scsi_Host *shost = rport_to_shost(rport);
@@ -504,27 +534,6 @@ void srp_start_tl_fail_timers(struct srp
 EXPORT_SYMBOL(srp_start_tl_fail_timers);
 
 /**
- * scsi_request_fn_active() - number of kernel threads inside scsi_request_fn()
- * @shost: SCSI host for which to count the number of scsi_request_fn() callers.
- */
-static int scsi_request_fn_active(struct Scsi_Host *shost)
-{
-	struct scsi_device *sdev;
-	struct request_queue *q;
-	int request_fn_active = 0;
-
-	shost_for_each_device(sdev, shost) {
-		q = sdev->request_queue;
-
-		spin_lock_irq(q->queue_lock);
-		request_fn_active += q->request_fn_active;
-		spin_unlock_irq(q->queue_lock);
-	}
-
-	return request_fn_active;
-}
-
-/**
  * srp_reconnect_rport() - reconnect to an SRP target port
  * @rport: SRP target port.
  *
@@ -559,8 +568,7 @@ int srp_reconnect_rport(struct srp_rport
 	if (res)
 		goto out;
 	scsi_target_block(&shost->shost_gendev);
-	while (scsi_request_fn_active(shost))
-		msleep(20);
+	srp_wait_for_queuecommand(shost);
 	res = rport->state != SRP_RPORT_LOST ? i->f->reconnect(rport) : -ENODEV;
 	pr_debug("%s (state %d): transport.reconnect() returned %d\n",
 		 dev_name(&shost->shost_gendev), rport->state, res);
author maintainer
#43 lore raw

PATCH 44/58 scsi_transport_srp: Fix a race condition

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit 535fb906225fb7436cb658144d0c0cea14a26f3e upstream.

Avoid that srp_terminate_io() can get invoked while srp_queuecommand() is in progress. This patch avoids that an I/O timeout can trigger the following kernel warning:

WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]()
Call Trace:
 [<ffffffff814c65a2>] dump_stack+0x4e/0x68
 [<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0
 [<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20
 [<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp]
 [<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp]
 [<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp]
 [<ffffffff8106e09b>] process_one_work+0x1db/0x780
 [<ffffffff8106e75b>] worker_thread+0x11b/0x450
 [<ffffffff81073c64>] kthread+0xe4/0x100
 [<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0

See also patch "scsi_transport_srp: Add transport layer error handling" (commit ID 29c17324803c).

Cc James Bottomley <[email protected]>
Cc Sagi Grimberg <[email protected]>
Cc Sebastian Parschauer <[email protected]>
---
 drivers/scsi/scsi_transport_srp.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/scsi/scsi_transport_srp.c +3 -1
@@ -439,8 +439,10 @@ static void __rport_fail_io_fast(struct
 
 	/* Involve the LLD if possible to terminate all I/O on the rport. */
 	i = to_srp_internal(shost->transportt);
-	if (i->f->terminate_rport_io)
+	if (i->f->terminate_rport_io) {
+		srp_wait_for_queuecommand(shost);
 		i->f->terminate_rport_io(rport);
+	}
 }
 
 /**
author maintainer
#44 lore raw

PATCH 45/58 IB/srp: Remove an extraneous scsi_host_put() from an error path

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit fb49c8bbaae70b14fea2b4590a90a21539f88526 upstream.

Fix a scsi_get_host() / scsi_host_put() imbalance in the error path of srp_create_target(). See also patch "IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning" (commit ID 34aa654ecb8e).

---
 drivers/infiniband/ulp/srp/ib_srp.c |   13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)
drivers/infiniband/ulp/srp/ib_srp.c +5 -8
@@ -3171,11 +3171,11 @@ static ssize_t srp_create_target(struct
 
 	ret = srp_parse_options(buf, target);
 	if (ret)
-		goto err;
+		goto out;
 
 	ret = scsi_init_shared_tag_map(target_host, target_host->can_queue);
 	if (ret)
-		goto err;
+		goto out;
 
 	target->req_ring_size = target->queue_size - SRP_TSK_MGMT_SQ_SIZE;
 
@@ -3186,7 +3186,7 @@ static ssize_t srp_create_target(struct
 			     be64_to_cpu(target->ioc_guid),
 			     be64_to_cpu(target->initiator_ext));
 		ret = -EEXIST;
-		goto err;
+		goto out;
 	}
 
 	if (!srp_dev->has_fmr && !srp_dev->has_fr && !target->allow_ext_sg &&
@@ -3207,7 +3207,7 @@ static ssize_t srp_create_target(struct
 	spin_lock_init(&target->lock);
 	ret = ib_query_gid(ibdev, host->port, 0, &target->sgid);
 	if (ret)
-		goto err;
+		goto out;
 
 	ret = -ENOMEM;
 	target->ch_count = max_t(unsigned, num_online_nodes(),
@@ -3218,7 +3218,7 @@ static ssize_t srp_create_target(struct
 	target->ch = kcalloc(target->ch_count, sizeof(*target->ch),
 			     GFP_KERNEL);
 	if (!target->ch)
-		goto err;
+		goto out;
 
 	node_idx = 0;
 	for_each_online_node(node) {
@@ -3314,9 +3314,6 @@ err_disconnect:
 	}
 
 	kfree(target->ch);
-
-err:
-	scsi_host_put(target_host);
 	goto out;
 }
 
author maintainer
#45 lore raw

PATCH 46/58 IB/srp: Fix a connection setup race

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit 8de9fe3a1d4ac8c3e4953fa4b7d81f863f5196ad upstream.

Avoid that receiving a DREQ while RDMA channels are being established causes target->qp_in_error to be reset.

---
 drivers/infiniband/ulp/srp/ib_srp.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/infiniband/ulp/srp/ib_srp.c +3 -2
@@ -992,8 +992,6 @@ static int srp_connect_ch(struct srp_rdm
 
 	WARN_ON_ONCE(!multich && target->connected);
 
-	target->qp_in_error = false;
-
 	ret = srp_lookup_path(ch);
 	if (ret)
 		return ret;
@@ -1242,6 +1240,9 @@ static int srp_rport_reconnect(struct sr
 		for (j = 0; j < target->queue_size; ++j)
 			list_add(&ch->tx_ring[j]->list, &ch->free_tx);
 	}
+
+	target->qp_in_error = false;
+
 	for (i = 0; i < target->ch_count; i++) {
 		ch = &target->ch[i];
 		if (ret || !ch->target) {
author maintainer
#46 lore raw

PATCH 47/58 IB/srp: Fix connection state tracking

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit c014c8cd31b161e12deb81c0f7f477811bd1eddc upstream.

Reception of a DREQ message only causes the state of a single channel to change. Hence move the 'connected' member variable from the target to the channel data structure. This patch avoids that following false positive warning can be reported by srp_destroy_qp():

WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]()
Call Trace:
[<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp]
[<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp]
[<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp]
[<ffffffff81346f60>] dev_attr_store+0x20/0x30
[<ffffffff811dd90f>] sysfs_write_file+0xef/0x170
[<ffffffff8116d248>] vfs_write+0xc8/0x190
[<ffffffff8116d411>] sys_write+0x51/0x90
---
 drivers/infiniband/ulp/srp/ib_srp.c |   60 +++++++++++++++++-------------------
 drivers/infiniband/ulp/srp/ib_srp.h |    2 -
 2 files changed, 30 insertions(+), 32 deletions(-)
drivers/infiniband/ulp/srp/ib_srp.c +29 -31
@@ -464,14 +464,13 @@ static struct srp_fr_pool *srp_alloc_fr_
  */
 static void srp_destroy_qp(struct srp_rdma_ch *ch)
 {
-	struct srp_target_port *target = ch->target;
 	static struct ib_qp_attr attr = { .qp_state = IB_QPS_ERR };
 	static struct ib_recv_wr wr = { .wr_id = SRP_LAST_WR_ID };
 	struct ib_recv_wr *bad_wr;
 	int ret;
 
 	/* Destroying a QP and reusing ch->done is only safe if not connected */
-	WARN_ON_ONCE(target->connected);
+	WARN_ON_ONCE(ch->connected);
 
 	ret = ib_modify_qp(ch->qp, &attr, IB_QP_STATE);
 	WARN_ONCE(ret, "ib_cm_init_qp_attr() returned %d\n", ret);
@@ -810,35 +809,19 @@ static bool srp_queue_remove_work(struct
 	return changed;
 }
 
-static bool srp_change_conn_state(struct srp_target_port *target,
-				  bool connected)
-{
-	bool changed = false;
-
-	spin_lock_irq(&target->lock);
-	if (target->connected != connected) {
-		target->connected = connected;
-		changed = true;
-	}
-	spin_unlock_irq(&target->lock);
-
-	return changed;
-}
-
 static void srp_disconnect_target(struct srp_target_port *target)
 {
 	struct srp_rdma_ch *ch;
 	int i;
 
-	if (srp_change_conn_state(target, false)) {
-		/* XXX should send SRP_I_LOGOUT request */
+	/* XXX should send SRP_I_LOGOUT request */
 
-		for (i = 0; i < target->ch_count; i++) {
-			ch = &target->ch[i];
-			if (ch->cm_id && ib_send_cm_dreq(ch->cm_id, NULL, 0)) {
-				shost_printk(KERN_DEBUG, target->scsi_host,
-					     PFX "Sending CM DREQ failed\n");
-			}
+	for (i = 0; i < target->ch_count; i++) {
+		ch = &target->ch[i];
+		ch->connected = false;
+		if (ch->cm_id && ib_send_cm_dreq(ch->cm_id, NULL, 0)) {
+			shost_printk(KERN_DEBUG, target->scsi_host,
+				     PFX "Sending CM DREQ failed\n");
 		}
 	}
 }
@@ -985,12 +968,26 @@ static void srp_rport_delete(struct srp_
 	srp_queue_remove_work(target);
 }
 
+/**
+ * srp_connected_ch() - number of connected channels
+ * @target: SRP target port.
+ */
+static int srp_connected_ch(struct srp_target_port *target)
+{
+	int i, c = 0;
+
+	for (i = 0; i < target->ch_count; i++)
+		c += target->ch[i].connected;
+
+	return c;
+}
+
 static int srp_connect_ch(struct srp_rdma_ch *ch, bool multich)
 {
 	struct srp_target_port *target = ch->target;
 	int ret;
 
-	WARN_ON_ONCE(!multich && target->connected);
+	WARN_ON_ONCE(!multich && srp_connected_ch(target) > 0);
 
 	ret = srp_lookup_path(ch);
 	if (ret)
@@ -1013,7 +1010,7 @@ static int srp_connect_ch(struct srp_rdm
 		 */
 		switch (ch->status) {
 		case 0:
-			srp_change_conn_state(target, true);
+			ch->connected = true;
 			return 0;
 
 		case SRP_PORT_REDIRECT:
@@ -1929,7 +1926,7 @@ static void srp_handle_qp_err(u64 wr_id,
 		return;
 	}
 
-	if (target->connected && !target->qp_in_error) {
+	if (ch->connected && !target->qp_in_error) {
 		if (wr_id & LOCAL_INV_WR_ID_MASK) {
 			shost_printk(KERN_ERR, target->scsi_host, PFX
 				     "LOCAL_INV failed with status %d\n",
@@ -2367,7 +2364,7 @@ static int srp_cm_handler(struct ib_cm_i
 	case IB_CM_DREQ_RECEIVED:
 		shost_printk(KERN_WARNING, target->scsi_host,
 			     PFX "DREQ received - connection closed\n");
-		srp_change_conn_state(target, false);
+		ch->connected = false;
 		if (ib_send_cm_drep(cm_id, NULL, 0))
 			shost_printk(KERN_ERR, target->scsi_host,
 				     PFX "Sending CM DREP failed\n");
@@ -2423,7 +2420,7 @@ static int srp_send_tsk_mgmt(struct srp_
 	struct srp_iu *iu;
 	struct srp_tsk_mgmt *tsk_mgmt;
 
-	if (!target->connected || target->qp_in_error)
+	if (!ch->connected || target->qp_in_error)
 		return -1;
 
 	init_completion(&ch->tsk_mgmt_done);
@@ -2797,7 +2794,8 @@ static int srp_add_target(struct srp_hos
 	scsi_scan_target(&target->scsi_host->shost_gendev,
 			 0, target->scsi_id, SCAN_WILD_CARD, 0);
 
-	if (!target->connected || target->qp_in_error) {
+	if (srp_connected_ch(target) < target->ch_count ||
+	    target->qp_in_error) {
 		shost_printk(KERN_INFO, target->scsi_host,
 			     PFX "SCSI scan failed - removing SCSI host\n");
 		srp_queue_remove_work(target);
drivers/infiniband/ulp/srp/ib_srp.h +1 -1
@@ -170,6 +170,7 @@ struct srp_rdma_ch {
 
 	struct completion	tsk_mgmt_done;
 	u8			tsk_mgmt_status;
+	bool			connected;
 };
 
 /**
@@ -214,7 +215,6 @@ struct srp_target_port {
 	__be16			pkey;
 
 	u32			rq_tmo_jiffies;
-	bool			connected;
 
 	int			zero_req_lim;
 
author maintainer
#47 lore raw

PATCH 48/58 IB/srp: Fix reconnection failure handling

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

commit a44074f14ba1ea0747ea737026eb929b81993dc3 upstream.

Although it is possible to let SRP I/O continue if a reconnect results in a reduction of the number of channels, the current code does not handle this scenario correctly. Instead of making the reconnect code more complex, consider this as a reconnection failure.

---
 drivers/infiniband/ulp/srp/ib_srp.c |    5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/infiniband/ulp/srp/ib_srp.c +1 -4
@@ -1242,11 +1242,8 @@ static int srp_rport_reconnect(struct sr
 
 	for (i = 0; i < target->ch_count; i++) {
 		ch = &target->ch[i];
-		if (ret || !ch->target) {
-			if (i > 1)
-				ret = 0;
+		if (ret || !ch->target)
 			break;
-		}
 		ret = srp_connect_ch(ch, multich);
 		multich = true;
 	}
author maintainer
#48 lore raw

PATCH 49/58 genirq: devres: Fix testing return value of request_any_context_irq()

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Axel Lin <[email protected]>

commit 63781394c540dd9e666a6b21d70b64dd52bce76e upstream.

request_any_context_irq() returns a negative value on failure. It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success. So fix testing return value of request_any_context_irq().

Also fixup the return value of devm_request_any_context_irq() to make it consistent with request_any_context_irq().

---
 kernel/irq/devres.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
kernel/irq/devres.c +2 -2
@@ -104,7 +104,7 @@ int devm_request_any_context_irq(struct
 		return -ENOMEM;
 
 	rc = request_any_context_irq(irq, handler, irqflags, devname, dev_id);
-	if (rc) {
+	if (rc < 0) {
 		devres_free(dr);
 		return rc;
 	}
@@ -113,7 +113,7 @@ int devm_request_any_context_irq(struct
 	dr->dev_id = dev_id;
 	devres_add(dev, dr);
 
-	return 0;
+	return rc;
 }
 EXPORT_SYMBOL(devm_request_any_context_irq);
 
author maintainer
#49 lore raw

PATCH 50/58 video: mxsfb: Make sure axi clock is enabled when accessing registers

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Liu Ying <[email protected]>

commit 2fa3b4c4a78a5db3502ab9e32630ea660ff923d0 upstream.

The LCDIF engines embedded in i.MX6sl and i.MX6sx SoCs need the axi clock as the engine's system clock. The clock should be enabled when accessing LCDIF registers, otherwise the kernel would hang up. We should also keep the clock enabled when the engine is being active to scan out frames from memory. This patch makes sure the axi clock is enabled when accessing registers so that the kernel hang up issue can be fixed.

---
 drivers/video/fbdev/mxsfb.c |   68 ++++++++++++++++++++++++++++++++++----------
 1 file changed, 54 insertions(+), 14 deletions(-)
drivers/video/fbdev/mxsfb.c +54 -14
@@ -316,6 +316,18 @@ static int mxsfb_check_var(struct fb_var
 	return 0;
 }
 
+static inline void mxsfb_enable_axi_clk(struct mxsfb_info *host)
+{
+	if (host->clk_axi)
+		clk_prepare_enable(host->clk_axi);
+}
+
+static inline void mxsfb_disable_axi_clk(struct mxsfb_info *host)
+{
+	if (host->clk_axi)
+		clk_disable_unprepare(host->clk_axi);
+}
+
 static void mxsfb_enable_controller(struct fb_info *fb_info)
 {
 	struct mxsfb_info *host = to_imxfb_host(fb_info);
@@ -333,14 +345,13 @@ static void mxsfb_enable_controller(stru
 		}
 	}
 
-	if (host->clk_axi)
-		clk_prepare_enable(host->clk_axi);
-
 	if (host->clk_disp_axi)
 		clk_prepare_enable(host->clk_disp_axi);
 	clk_prepare_enable(host->clk);
 	clk_set_rate(host->clk, PICOS2KHZ(fb_info->var.pixclock) * 1000U);
 
+	mxsfb_enable_axi_clk(host);
+
 	/* if it was disabled, re-enable the mode again */
 	writel(CTRL_DOTCLK_MODE, host->base + LCDC_CTRL + REG_SET);
 
@@ -380,11 +391,11 @@ static void mxsfb_disable_controller(str
 	reg = readl(host->base + LCDC_VDCTRL4);
 	writel(reg & ~VDCTRL4_SYNC_SIGNALS_ON, host->base + LCDC_VDCTRL4);
 
+	mxsfb_disable_axi_clk(host);
+
 	clk_disable_unprepare(host->clk);
 	if (host->clk_disp_axi)
 		clk_disable_unprepare(host->clk_disp_axi);
-	if (host->clk_axi)
-		clk_disable_unprepare(host->clk_axi);
 
 	host->enabled = 0;
 
@@ -421,6 +432,8 @@ static int mxsfb_set_par(struct fb_info
 		mxsfb_disable_controller(fb_info);
 	}
 
+	mxsfb_enable_axi_clk(host);
+
 	/* clear the FIFOs */
 	writel(CTRL1_FIFO_CLEAR, host->base + LCDC_CTRL1 + REG_SET);
 
@@ -438,6 +451,7 @@ static int mxsfb_set_par(struct fb_info
 		ctrl |= CTRL_SET_WORD_LENGTH(3);
 		switch (host->ld_intf_width) {
 		case STMLCDIF_8BIT:
+			mxsfb_disable_axi_clk(host);
 			dev_err(&host->pdev->dev,
 					"Unsupported LCD bus width mapping\n");
 			return -EINVAL;
@@ -451,6 +465,7 @@ static int mxsfb_set_par(struct fb_info
 		writel(CTRL1_SET_BYTE_PACKAGING(0x7), host->base + LCDC_CTRL1);
 		break;
 	default:
+		mxsfb_disable_axi_clk(host);
 		dev_err(&host->pdev->dev, "Unhandled color depth of %u\n",
 				fb_info->var.bits_per_pixel);
 		return -EINVAL;
@@ -504,6 +519,8 @@ static int mxsfb_set_par(struct fb_info
 			fb_info->fix.line_length * fb_info->var.yoffset,
 			host->base + host->devdata->next_buf);
 
+	mxsfb_disable_axi_clk(host);
+
 	if (reenable)
 		mxsfb_enable_controller(fb_info);
 
@@ -582,10 +599,14 @@ static int mxsfb_pan_display(struct fb_v
 
 	offset = fb_info->fix.line_length * var->yoffset;
 
+	mxsfb_enable_axi_clk(host);
+
 	/* update on next VSYNC */
 	writel(fb_info->fix.smem_start + offset,
 			host->base + host->devdata->next_buf);
 
+	mxsfb_disable_axi_clk(host);
+
 	return 0;
 }
 
@@ -608,13 +629,17 @@ static int mxsfb_restore_mode(struct mxs
 	unsigned line_count;
 	unsigned period;
 	unsigned long pa, fbsize;
-	int bits_per_pixel, ofs;
+	int bits_per_pixel, ofs, ret = 0;
 	u32 transfer_count, vdctrl0, vdctrl2, vdctrl3, vdctrl4, ctrl;
 
+	mxsfb_enable_axi_clk(host);
+
 	/* Only restore the mode when the controller is running */
 	ctrl = readl(host->base + LCDC_CTRL);
-	if (!(ctrl & CTRL_RUN))
-		return -EINVAL;
+	if (!(ctrl & CTRL_RUN)) {
+		ret = -EINVAL;
+		goto err;
+	}
 
 	vdctrl0 = readl(host->base + LCDC_VDCTRL0);
 	vdctrl2 = readl(host->base + LCDC_VDCTRL2);
@@ -635,7 +660,8 @@ static int mxsfb_restore_mode(struct mxs
 		break;
 	case 1:
 	default:
-		return -EINVAL;
+		ret = -EINVAL;
+		goto err;
 	}
 
 	fb_info->var.bits_per_pixel = bits_per_pixel;
@@ -673,10 +699,14 @@ static int mxsfb_restore_mode(struct mxs
 
 	pa = readl(host->base + host->devdata->cur_buf);
 	fbsize = fb_info->fix.line_length * vmode->yres;
-	if (pa < fb_info->fix.smem_start)
-		return -EINVAL;
-	if (pa + fbsize > fb_info->fix.smem_start + fb_info->fix.smem_len)
-		return -EINVAL;
+	if (pa < fb_info->fix.smem_start) {
+		ret = -EINVAL;
+		goto err;
+	}
+	if (pa + fbsize > fb_info->fix.smem_start + fb_info->fix.smem_len) {
+		ret = -EINVAL;
+		goto err;
+	}
 	ofs = pa - fb_info->fix.smem_start;
 	if (ofs) {
 		memmove(fb_info->screen_base, fb_info->screen_base + ofs, fbsize);
@@ -689,7 +719,11 @@ static int mxsfb_restore_mode(struct mxs
 	clk_prepare_enable(host->clk);
 	host->enabled = 1;
 
-	return 0;
+err:
+	if (ret)
+		mxsfb_disable_axi_clk(host);
+
+	return ret;
 }
 
 static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host,
@@ -915,7 +949,9 @@ static int mxsfb_probe(struct platform_d
 	}
 
 	if (!host->enabled) {
+		mxsfb_enable_axi_clk(host);
 		writel(0, host->base + LCDC_CTRL);
+		mxsfb_disable_axi_clk(host);
 		mxsfb_set_par(fb_info);
 		mxsfb_enable_controller(fb_info);
 	}
@@ -954,11 +990,15 @@ static void mxsfb_shutdown(struct platfo
 	struct fb_info *fb_info = platform_get_drvdata(pdev);
 	struct mxsfb_info *host = to_imxfb_host(fb_info);
 
+	mxsfb_enable_axi_clk(host);
+
 	/*
 	 * Force stop the LCD controller as keeping it running during reboot
 	 * might interfere with the BootROM's boot mode pads sampling.
 	 */
 	writel(CTRL_RUN, host->base + LCDC_CTRL + REG_CLR);
+
+	mxsfb_disable_axi_clk(host);
 }
 
 static struct platform_driver mxsfb_driver = {
author maintainer
#50 lore raw

PATCH 51/58 leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Grygorii Strashko <[email protected]>

commit 084609bf727981c7a2e6e69aefe0052c9d793300 upstream.

Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of hibernation callbacks means those pm functions will not be called upon hibernation - that leads to system crash on ARM during freezing if gpio-led is used in combination with CPU led trigger. It may happen after freeze_noirq stage (GPIO is suspended) and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.

Log:
PM: noirq freeze of devices complete after 1.425 msecs Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)

  WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370()
  44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access

CPU1: shutdown
^ or here

Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation callbacks and move led_suspend/led_resume under CONFIG_PM_SLEEP to avoid build warnings.

Fixes 73e1ab41a80d (leds: Convert led class driver from legacy pm ops to dev_pm_ops)
---
 drivers/leds/led-class.c |    7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/leds/led-class.c +3 -4
@@ -187,6 +187,7 @@ void led_classdev_resume(struct led_clas
 }
 EXPORT_SYMBOL_GPL(led_classdev_resume);
 
+#ifdef CONFIG_PM_SLEEP
 static int led_suspend(struct device *dev)
 {
 	struct led_classdev *led_cdev = dev_get_drvdata(dev);
@@ -206,11 +207,9 @@ static int led_resume(struct device *dev
 
 	return 0;
 }
+#endif
 
-static const struct dev_pm_ops leds_class_dev_pm_ops = {
-	.suspend        = led_suspend,
-	.resume         = led_resume,
-};
+static SIMPLE_DEV_PM_OPS(leds_class_dev_pm_ops, led_suspend, led_resume);
 
 /**
  * led_classdev_register - register a new object of led_classdev class.
author maintainer
#51 lore raw

PATCH 52/58 mtd: fix: avoid race condition when accessing mtd->usecount

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Brian Norris <[email protected]>

commit 073db4a51ee43ccb827f54a4261c0583b028d5ab upstream.

On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex.
kernel: Call Trace:
kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50
kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8
kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200
kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30
kernel: [<ffffffff8022006c>] __fput+0xac/0x250
kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120
kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18
kernel:
kernel:

        Code: 2442ffff  ac8202d8  000217fe <00020336> dc820128  10400003
               00000000  0040f809  00000000

kernel: ---[ end trace 080fbb4579b47a73 ]---

Fixed by taking the mutex in blktrans_open and blktrans_release.

Note that this locking is already suggested in
include/linux/mtd/blktrans.h:

struct mtd_blktrans_ops {
...

	/* Called with mtd_table_mutex held; no race with add/remove */
	int (*open)(struct mtd_blktrans_dev *dev);
	void (*release)(struct mtd_blktrans_dev *dev);

...
};

But we weren't following it.

Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten.

---
 drivers/mtd/mtd_blkdevs.c |    5 +++++
 1 file changed, 5 insertions(+)
drivers/mtd/mtd_blkdevs.c +5 -0
@@ -200,6 +200,7 @@ static int blktrans_open(struct block_de
 		return -ERESTARTSYS; /* FIXME: busy loop! -arnd*/
 
 	mutex_lock(&dev->lock);
+	mutex_lock(&mtd_table_mutex);
 
 	if (dev->open)
 		goto unlock;
@@ -223,6 +224,7 @@ static int blktrans_open(struct block_de
 
 unlock:
 	dev->open++;
+	mutex_unlock(&mtd_table_mutex);
 	mutex_unlock(&dev->lock);
 	blktrans_dev_put(dev);
 	return ret;
@@ -233,6 +235,7 @@ error_release:
 error_put:
 	module_put(dev->tr->owner);
 	kref_put(&dev->ref, blktrans_dev_release);
+	mutex_unlock(&mtd_table_mutex);
 	mutex_unlock(&dev->lock);
 	blktrans_dev_put(dev);
 	return ret;
@@ -246,6 +249,7 @@ static void blktrans_release(struct gend
 		return;
 
 	mutex_lock(&dev->lock);
+	mutex_lock(&mtd_table_mutex);
 
 	if (--dev->open)
 		goto unlock;
@@ -259,6 +263,7 @@ static void blktrans_release(struct gend
 		__put_mtd_device(dev->mtd);
 	}
 unlock:
+	mutex_unlock(&mtd_table_mutex);
 	mutex_unlock(&dev->lock);
 	blktrans_dev_put(dev);
 }
author maintainer
#52 lore raw

PATCH 54/58 PCI: Propagate the "ignore hotplug" setting to parent

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Rafael J. Wysocki" <[email protected]>

commit 0824965140fff1bf640a987dc790d1594a8e0699 upstream.

Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the ignore_hotplug setting of the device to its parent bridge in case hotplug notifications related to the graphics adapter switching are given for the bridge rather than for the device itself (they need to be ignored in both cases).

Fixes b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Reported-and-tested-by tiagdtd-lava <[email protected]>
---
 drivers/pci/pci.c   |   11 +++++++++++
 include/linux/pci.h |    6 +-----
 2 files changed, 12 insertions(+), 5 deletions(-)
drivers/pci/pci.c +11 -0
@@ -4319,6 +4319,17 @@ bool pci_device_is_present(struct pci_de
 }
 EXPORT_SYMBOL_GPL(pci_device_is_present);
 
+void pci_ignore_hotplug(struct pci_dev *dev)
+{
+	struct pci_dev *bridge = dev->bus->self;
+
+	dev->ignore_hotplug = 1;
+	/* Propagate the "ignore hotplug" setting to the parent bridge. */
+	if (bridge)
+		bridge->ignore_hotplug = 1;
+}
+EXPORT_SYMBOL_GPL(pci_ignore_hotplug);
+
 #define RESOURCE_ALIGNMENT_PARAM_SIZE COMMAND_LINE_SIZE
 static char resource_alignment_param[RESOURCE_ALIGNMENT_PARAM_SIZE] = {0};
 static DEFINE_SPINLOCK(resource_alignment_lock);
include/linux/pci.h +1 -5
@@ -1002,6 +1002,7 @@ int __must_check pci_assign_resource(str
 int __must_check pci_reassign_resource(struct pci_dev *dev, int i, resource_size_t add_size, resource_size_t align);
 int pci_select_bars(struct pci_dev *dev, unsigned long flags);
 bool pci_device_is_present(struct pci_dev *pdev);
+void pci_ignore_hotplug(struct pci_dev *dev);
 
 /* ROM control related routines */
 int pci_enable_rom(struct pci_dev *pdev);
@@ -1039,11 +1040,6 @@ bool pci_dev_run_wake(struct pci_dev *de
 bool pci_check_pme_status(struct pci_dev *dev);
 void pci_pme_wakeup_bus(struct pci_bus *bus);
 
-static inline void pci_ignore_hotplug(struct pci_dev *dev)
-{
-	dev->ignore_hotplug = 1;
-}
-
 static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state,
 				  bool enable)
 {
author maintainer
#53 lore raw

PATCH 55/58 PCI: Add pci_bus_addr_t

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yinghai Lu <[email protected]>

commit 3a9ad0b4fdcd57f775d3615004c8c64c021a9e7d upstream.

David Ahern reported that d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows") fails to boot on sparc/T5-8:

pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)

The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA addresses, i.e., bus addresses returned via the DMA API (dma_map_single(), etc.), while the PCI core assumed dma_addr_t could hold *any* bus address, including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so they don't fit in a dma_addr_t. d63e2e1f3df9 added new checking that tripped over this mismatch.

Add pci_bus_addr_t, which is wide enough to hold any PCI bus address, including both raw BAR values and DMA addresses. This will be 64 bits on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then dma_addr_t only needs to be wide enough to hold addresses from the DMA API.

[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at least as wide as dma_addr_t, documentation]

---
 Documentation/DMA-API-HOWTO.txt |   29 +++++++++++++++++------------
 Documentation/DMA-API.txt       |   30 +++++++++++++++---------------
 drivers/pci/Kconfig             |    4 ++++
 drivers/pci/bus.c               |   10 +++++-----
 drivers/pci/probe.c             |   12 ++++++------
 include/linux/pci.h             |   12 +++++++++---
 include/linux/types.h           |   12 ++++++++++--
 7 files changed, 66 insertions(+), 43 deletions(-)
Documentation/DMA-API-HOWTO.txt +17 -12
@@ -25,13 +25,18 @@ physical addresses.  These are the addre
 address is not directly useful to a driver; it must use ioremap() to map
 the space and produce a virtual address.
 
-I/O devices use a third kind of address: a "bus address" or "DMA address".
-If a device has registers at an MMIO address, or if it performs DMA to read
-or write system memory, the addresses used by the device are bus addresses.
-In some systems, bus addresses are identical to CPU physical addresses, but
-in general they are not.  IOMMUs and host bridges can produce arbitrary
+I/O devices use a third kind of address: a "bus address".  If a device has
+registers at an MMIO address, or if it performs DMA to read or write system
+memory, the addresses used by the device are bus addresses.  In some
+systems, bus addresses are identical to CPU physical addresses, but in
+general they are not.  IOMMUs and host bridges can produce arbitrary
 mappings between physical and bus addresses.
 
+From a device's point of view, DMA uses the bus address space, but it may
+be restricted to a subset of that space.  For example, even if a system
+supports 64-bit addresses for main memory and PCI BARs, it may use an IOMMU
+so devices only need to use 32-bit DMA addresses.
+
 Here's a picture and some examples:
 
                CPU                  CPU                  Bus
@@ -72,11 +77,11 @@ can use virtual address X to access the
 cannot because DMA doesn't go through the CPU virtual memory system.
 
 In some simple systems, the device can do DMA directly to physical address
-Y.  But in many others, there is IOMMU hardware that translates bus
+Y.  But in many others, there is IOMMU hardware that translates DMA
 addresses to physical addresses, e.g., it translates Z to Y.  This is part
 of the reason for the DMA API: the driver can give a virtual address X to
 an interface like dma_map_single(), which sets up any required IOMMU
-mapping and returns the bus address Z.  The driver then tells the device to
+mapping and returns the DMA address Z.  The driver then tells the device to
 do DMA to Z, and the IOMMU maps it to the buffer at address Y in system
 RAM.
 
@@ -98,7 +103,7 @@ First of all, you should make sure
 #include <linux/dma-mapping.h>
 
 is in your driver, which provides the definition of dma_addr_t.  This type
-can hold any valid DMA or bus address for the platform and should be used
+can hold any valid DMA address for the platform and should be used
 everywhere you hold a DMA address returned from the DMA mapping functions.
 
 			 What memory is DMA'able?
@@ -316,7 +321,7 @@ There are two types of DMA mappings:
   Think of "consistent" as "synchronous" or "coherent".
 
   The current default is to return consistent memory in the low 32
-  bits of the bus space.  However, for future compatibility you should
+  bits of the DMA space.  However, for future compatibility you should
   set the consistent mask even if this default is fine for your
   driver.
 
@@ -403,7 +408,7 @@ dma_alloc_coherent() returns two values:
 can use to access it from the CPU and dma_handle which you pass to the
 card.
 
-The CPU virtual address and the DMA bus address are both
+The CPU virtual address and the DMA address are both
 guaranteed to be aligned to the smallest PAGE_SIZE order which
 is greater than or equal to the requested size.  This invariant
 exists (for example) to guarantee that if you allocate a chunk
@@ -645,8 +650,8 @@ PLEASE NOTE:  The 'nents' argument to th
               dma_map_sg call.
 
 Every dma_map_{single,sg}() call should have its dma_unmap_{single,sg}()
-counterpart, because the bus address space is a shared resource and
-you could render the machine unusable by consuming all bus addresses.
+counterpart, because the DMA address space is a shared resource and
+you could render the machine unusable by consuming all DMA addresses.
 
 If you need to use the same streaming DMA region multiple times and touch
 the data in between the DMA transfers, the buffer needs to be synced
Documentation/DMA-API.txt +15 -15
@@ -18,10 +18,10 @@ Part I - dma_ API
 To get the dma_ API, you must #include <linux/dma-mapping.h>.  This
 provides dma_addr_t and the interfaces described below.
 
-A dma_addr_t can hold any valid DMA or bus address for the platform.  It
-can be given to a device to use as a DMA source or target.  A CPU cannot
-reference a dma_addr_t directly because there may be translation between
-its physical address space and the bus address space.
+A dma_addr_t can hold any valid DMA address for the platform.  It can be
+given to a device to use as a DMA source or target.  A CPU cannot reference
+a dma_addr_t directly because there may be translation between its physical
+address space and the DMA address space.
 
 Part Ia - Using large DMA-coherent buffers
 ------------------------------------------
@@ -42,7 +42,7 @@ It returns a pointer to the allocated re
 address space) or NULL if the allocation failed.
 
 It also returns a <dma_handle> which may be cast to an unsigned integer the
-same width as the bus and given to the device as the bus address base of
+same width as the bus and given to the device as the DMA address base of
 the region.
 
 Note: consistent memory can be expensive on some platforms, and the
@@ -193,7 +193,7 @@ dma_map_single(struct device *dev, void
 		      enum dma_data_direction direction)
 
 Maps a piece of processor virtual memory so it can be accessed by the
-device and returns the bus address of the memory.
+device and returns the DMA address of the memory.
 
 The direction for both APIs may be converted freely by casting.
 However the dma_ API uses a strongly typed enumerator for its
@@ -212,20 +212,20 @@ contiguous piece of memory.  For this re
 this API should be obtained from sources which guarantee it to be
 physically contiguous (like kmalloc).
 
-Further, the bus address of the memory must be within the
+Further, the DMA address of the memory must be within the
 dma_mask of the device (the dma_mask is a bit mask of the
-addressable region for the device, i.e., if the bus address of
-the memory ANDed with the dma_mask is still equal to the bus
+addressable region for the device, i.e., if the DMA address of
+the memory ANDed with the dma_mask is still equal to the DMA
 address, then the device can perform DMA to the memory).  To
 ensure that the memory allocated by kmalloc is within the dma_mask,
 the driver may specify various platform-dependent flags to restrict
-the bus address range of the allocation (e.g., on x86, GFP_DMA
-guarantees to be within the first 16MB of available bus addresses,
+the DMA address range of the allocation (e.g., on x86, GFP_DMA
+guarantees to be within the first 16MB of available DMA addresses,
 as required by ISA devices).
 
 Note also that the above constraints on physical contiguity and
 dma_mask may not apply if the platform has an IOMMU (a device which
-maps an I/O bus address to a physical memory address).  However, to be
+maps an I/O DMA address to a physical memory address).  However, to be
 portable, device driver writers may *not* assume that such an IOMMU
 exists.
 
@@ -296,7 +296,7 @@ reduce current DMA mapping usage or dela
 	dma_map_sg(struct device *dev, struct scatterlist *sg,
 		int nents, enum dma_data_direction direction)
 
-Returns: the number of bus address segments mapped (this may be shorter
+Returns: the number of DMA address segments mapped (this may be shorter
 than <nents> passed in if some elements of the scatter/gather list are
 physically or virtually adjacent and an IOMMU maps them with a single
 entry).
@@ -340,7 +340,7 @@ must be the same as those and passed in
 API.
 
 Note: <nents> must be the number you passed in, *not* the number of
-bus address entries returned.
+DMA address entries returned.
 
 void
 dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_handle, size_t size,
@@ -507,7 +507,7 @@ it's asked for coherent memory for this
 phys_addr is the CPU physical address to which the memory is currently
 assigned (this will be ioremapped so the CPU can access the region).
 
-device_addr is the bus address the device needs to be programmed
+device_addr is the DMA address the device needs to be programmed
 with to actually address this memory (this will be handed out as the
 dma_addr_t in dma_alloc_coherent()).
 
drivers/pci/Kconfig +4 -0
@@ -1,6 +1,10 @@
 #
 # PCI configuration
 #
+config PCI_BUS_ADDR_T_64BIT
+	def_bool y if (ARCH_DMA_ADDR_T_64BIT || 64BIT)
+	depends on PCI
+
 config PCI_MSI
 	bool "Message Signaled Interrupts (MSI and MSI-X)"
 	depends on PCI
drivers/pci/bus.c +5 -5
@@ -92,11 +92,11 @@ void pci_bus_remove_resources(struct pci
 }
 
 static struct pci_bus_region pci_32_bit = {0, 0xffffffffULL};
-#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+#ifdef CONFIG_PCI_BUS_ADDR_T_64BIT
 static struct pci_bus_region pci_64_bit = {0,
-				(dma_addr_t) 0xffffffffffffffffULL};
-static struct pci_bus_region pci_high = {(dma_addr_t) 0x100000000ULL,
-				(dma_addr_t) 0xffffffffffffffffULL};
+				(pci_bus_addr_t) 0xffffffffffffffffULL};
+static struct pci_bus_region pci_high = {(pci_bus_addr_t) 0x100000000ULL,
+				(pci_bus_addr_t) 0xffffffffffffffffULL};
 #endif
 
 /*
@@ -200,7 +200,7 @@ int pci_bus_alloc_resource(struct pci_bu
 					  resource_size_t),
 		void *alignf_data)
 {
-#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+#ifdef CONFIG_PCI_BUS_ADDR_T_64BIT
 	int rc;
 
 	if (res->flags & IORESOURCE_MEM_64) {
drivers/pci/probe.c +6 -6
@@ -253,8 +253,8 @@ int __pci_read_base(struct pci_dev *dev,
 	}
 
 	if (res->flags & IORESOURCE_MEM_64) {
-		if ((sizeof(dma_addr_t) < 8 || sizeof(resource_size_t) < 8) &&
-		    sz64 > 0x100000000ULL) {
+		if ((sizeof(pci_bus_addr_t) < 8 || sizeof(resource_size_t) < 8)
+		    && sz64 > 0x100000000ULL) {
 			res->flags |= IORESOURCE_UNSET | IORESOURCE_DISABLED;
 			res->start = 0;
 			res->end = 0;
@@ -263,7 +263,7 @@ int __pci_read_base(struct pci_dev *dev,
 			goto out;
 		}
 
-		if ((sizeof(dma_addr_t) < 8) && l) {
+		if ((sizeof(pci_bus_addr_t) < 8) && l) {
 			/* Above 32-bit boundary; try to reallocate */
 			res->flags |= IORESOURCE_UNSET;
 			res->start = 0;
@@ -398,7 +398,7 @@ static void pci_read_bridge_mmio_pref(st
 	struct pci_dev *dev = child->self;
 	u16 mem_base_lo, mem_limit_lo;
 	u64 base64, limit64;
-	dma_addr_t base, limit;
+	pci_bus_addr_t base, limit;
 	struct pci_bus_region region;
 	struct resource *res;
 
@@ -425,8 +425,8 @@ static void pci_read_bridge_mmio_pref(st
 		}
 	}
 
-	base = (dma_addr_t) base64;
-	limit = (dma_addr_t) limit64;
+	base = (pci_bus_addr_t) base64;
+	limit = (pci_bus_addr_t) limit64;
 
 	if (base != base64) {
 		dev_err(&dev->dev, "can't handle bridge window above 4GB (bus address %#010llx)\n",
include/linux/pci.h +9 -3
@@ -573,9 +573,15 @@ int raw_pci_read(unsigned int domain, un
 int raw_pci_write(unsigned int domain, unsigned int bus, unsigned int devfn,
 		  int reg, int len, u32 val);
 
+#ifdef CONFIG_PCI_BUS_ADDR_T_64BIT
+typedef u64 pci_bus_addr_t;
+#else
+typedef u32 pci_bus_addr_t;
+#endif
+
 struct pci_bus_region {
-	dma_addr_t start;
-	dma_addr_t end;
+	pci_bus_addr_t start;
+	pci_bus_addr_t end;
 };
 
 struct pci_dynids {
@@ -1120,7 +1126,7 @@ int __must_check pci_bus_alloc_resource(
 
 int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr);
 
-static inline dma_addr_t pci_bus_address(struct pci_dev *pdev, int bar)
+static inline pci_bus_addr_t pci_bus_address(struct pci_dev *pdev, int bar)
 {
 	struct pci_bus_region region;
 
include/linux/types.h +10 -2
@@ -139,12 +139,20 @@ typedef unsigned long blkcnt_t;
  */
 #define pgoff_t unsigned long
 
-/* A dma_addr_t can hold any valid DMA or bus address for the platform */
+/*
+ * A dma_addr_t can hold any valid DMA address, i.e., any address returned
+ * by the DMA API.
+ *
+ * If the DMA API only uses 32-bit addresses, dma_addr_t need only be 32
+ * bits wide.  Bus addresses, e.g., PCI BARs, may be wider than 32 bits,
+ * but drivers do memory-mapped I/O to ioremapped kernel virtual addresses,
+ * so they don't care about the size of the actual bus addresses.
+ */
 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
 typedef u64 dma_addr_t;
 #else
 typedef u32 dma_addr_t;
-#endif /* dma_addr_t */
+#endif
 
 #ifdef __CHECKER__
 #else
author maintainer
#54 lore raw

PATCH 56/58 PCI: pciehp: Wait for hotplug command completion where necessary

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Williamson <[email protected]>

commit a5dd4b4b0570b3bf880d563969b245dfbd170c1e upstream.

The commit referenced below deferred waiting for command completion until the start of the next command, allowing hardware to do the latching asynchronously. Unfortunately, being ready to accept a new command is the only indication we have that the previous command is completed. In cases where we need that state change to be enabled, we must still wait for completion. For instance, pciehp_reset_slot() attempts to disable anything that might generate a surprise hotplug on slots that support presence detection. If we don't wait for those settings to latch before the secondary bus reset, we negate any value in attempting to prevent the spurious hotplug.

Create a base function with optional wait and helper functions so that pcie_write_cmd() turns back into the "safe" interface which waits before and after issuing a command and add pcie_write_cmd_nowait(), which eliminates the trailing wait for asynchronous completion. The following functions are returned to their previous behavior:

pciehp_power_on_slot
pciehp_power_off_slot
pcie_disable_notification
pciehp_reset_slot

The rationale is that pciehp_power_on_slot() enables the link and therefore relies on completion of power-on. pciehp_power_off_slot() and pcie_disable_notification() need a wait because data structures may be freed after these calls and continued signaling from the device would be unexpected. And, of course, pciehp_reset_slot() needs to wait for the scenario outlined above.

Fixes 3461a068661c ("PCI: pciehp: Wait for hotplug command completion lazily")
---
 drivers/pci/hotplug/pciehp_hpc.c |   52 ++++++++++++++++++++++++++++-----------
 1 file changed, 38 insertions(+), 14 deletions(-)
drivers/pci/hotplug/pciehp_hpc.c +38 -14
@@ -176,20 +176,17 @@ static void pcie_wait_cmd(struct control
 			  jiffies_to_msecs(jiffies - ctrl->cmd_started));
 }
 
-/**
- * pcie_write_cmd - Issue controller command
- * @ctrl: controller to which the command is issued
- * @cmd:  command value written to slot control register
- * @mask: bitmask of slot control register to be modified
- */
-static void pcie_write_cmd(struct controller *ctrl, u16 cmd, u16 mask)
+static void pcie_do_write_cmd(struct controller *ctrl, u16 cmd,
+			      u16 mask, bool wait)
 {
 	struct pci_dev *pdev = ctrl_dev(ctrl);
 	u16 slot_ctrl;
 
 	mutex_lock(&ctrl->ctrl_lock);
 
-	/* Wait for any previous command that might still be in progress */
+	/*
+	 * Always wait for any previous command that might still be in progress
+	 */
 	pcie_wait_cmd(ctrl);
 
 	pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, &slot_ctrl);
@@ -201,9 +198,33 @@ static void pcie_write_cmd(struct contro
 	ctrl->cmd_started = jiffies;
 	ctrl->slot_ctrl = slot_ctrl;
 
+	/*
+	 * Optionally wait for the hardware to be ready for a new command,
+	 * indicating completion of the above issued command.
+	 */
+	if (wait)
+		pcie_wait_cmd(ctrl);
+
 	mutex_unlock(&ctrl->ctrl_lock);
 }
 
+/**
+ * pcie_write_cmd - Issue controller command
+ * @ctrl: controller to which the command is issued
+ * @cmd:  command value written to slot control register
+ * @mask: bitmask of slot control register to be modified
+ */
+static void pcie_write_cmd(struct controller *ctrl, u16 cmd, u16 mask)
+{
+	pcie_do_write_cmd(ctrl, cmd, mask, true);
+}
+
+/* Same as above without waiting for the hardware to latch */
+static void pcie_write_cmd_nowait(struct controller *ctrl, u16 cmd, u16 mask)
+{
+	pcie_do_write_cmd(ctrl, cmd, mask, false);
+}
+
 bool pciehp_check_link_active(struct controller *ctrl)
 {
 	struct pci_dev *pdev = ctrl_dev(ctrl);
@@ -422,7 +443,7 @@ void pciehp_set_attention_status(struct
 	default:
 		return;
 	}
-	pcie_write_cmd(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC);
+	pcie_write_cmd_nowait(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, slot_cmd);
 }
@@ -434,7 +455,8 @@ void pciehp_green_led_on(struct slot *sl
 	if (!PWR_LED(ctrl))
 		return;
 
-	pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_ON, PCI_EXP_SLTCTL_PIC);
+	pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_ON,
+			      PCI_EXP_SLTCTL_PIC);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL,
 		 PCI_EXP_SLTCTL_PWR_IND_ON);
@@ -447,7 +469,8 @@ void pciehp_green_led_off(struct slot *s
 	if (!PWR_LED(ctrl))
 		return;
 
-	pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF, PCI_EXP_SLTCTL_PIC);
+	pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_OFF,
+			      PCI_EXP_SLTCTL_PIC);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL,
 		 PCI_EXP_SLTCTL_PWR_IND_OFF);
@@ -460,7 +483,8 @@ void pciehp_green_led_blink(struct slot
 	if (!PWR_LED(ctrl))
 		return;
 
-	pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_IND_BLINK, PCI_EXP_SLTCTL_PIC);
+	pcie_write_cmd_nowait(ctrl, PCI_EXP_SLTCTL_PWR_IND_BLINK,
+			      PCI_EXP_SLTCTL_PIC);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL,
 		 PCI_EXP_SLTCTL_PWR_IND_BLINK);
@@ -613,7 +637,7 @@ void pcie_enable_notification(struct con
 		PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_CCIE |
 		PCI_EXP_SLTCTL_DLLSCE);
 
-	pcie_write_cmd(ctrl, cmd, mask);
+	pcie_write_cmd_nowait(ctrl, cmd, mask);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, cmd);
 }
@@ -664,7 +688,7 @@ int pciehp_reset_slot(struct slot *slot,
 	pci_reset_bridge_secondary_bus(ctrl->pcie->port);
 
 	pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, stat_mask);
-	pcie_write_cmd(ctrl, ctrl_mask, ctrl_mask);
+	pcie_write_cmd_nowait(ctrl, ctrl_mask, ctrl_mask);
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, ctrl_mask);
 	if (pciehp_poll_mode)
author maintainer
#55 lore raw

PATCH 57/58 of/pci: Fix pci_address_to_pio() conversion of CPU address to I/O port

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Zhichang Yuan <[email protected]>

commit 5dbb4c6167229c8d4f528e8ec26699a7305000a3 upstream.

41f8bba7f555 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()") added support for systems with several I/O ranges described by OF bindings. It modified pci_address_to_pio() look up the io_range for a given CPU physical address, but the conversion was wrong.

Fix the conversion of address to I/O port.

[bhelgaas: changelog]
Fixes 41f8bba7f555 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()")
---
 drivers/of/address.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/of/address.c +1 -1
@@ -765,7 +765,7 @@ unsigned long __weak pci_address_to_pio(
 	spin_lock(&io_range_lock);
 	list_for_each_entry(res, &io_range_list, list) {
 		if (address >= res->start && address < res->start + res->size) {
-			addr = res->start - address + offset;
+			addr = address - res->start + offset;
 			break;
 		}
 		offset += res->size;
author maintainer
#56 lore raw

PATCH 58/58 Input: pixcir_i2c_ts - fix receive error

In reply to Greg Kroah-Hartman

4.0-stable review patch. If anyone has any objections, please let me know.

------------------

From: Frodo Lai <[email protected]>

commit 469d7d22cea146e40efe8c330e5164b4d8f13934 upstream.

The i2c_master_recv() uses readsize to receive data from i2c but compares to size of rdbuf which is always 27. This would cause problem when the max_fingers is not 5. Change the comparison value to readsize instead.

Fixes 36874c7e219 ("Input: pixcir_i2c_ts - support up to 5 fingers and

hardware tracking IDs:)

---
 drivers/input/touchscreen/pixcir_i2c_ts.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +1 -1
@@ -78,7 +78,7 @@ static void pixcir_ts_parse(struct pixci
 	}
 
 	ret = i2c_master_recv(tsdata->client, rdbuf, readsize);
-	if (ret != sizeof(rdbuf)) {
+	if (ret != readsize) {
 		dev_err(&tsdata->client->dev,
 			"%s: i2c_master_recv failed(), ret=%d\n",
 			__func__, ret);
#57 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Build results:

	total: 124 pass: 124 fail: 0
Qemu test results:
	total: 30 pass: 30 fail: 0

Details are available at http://server.roeck-us.net:8010/builders/

Guenter

#58 lore raw
In reply to Greg Kroah-Hartman
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Compiled and booted on x86_32. No errors in dmesg.

regards
sudip

#59 lore raw
In reply to Greg Kroah-Hartman
Quoted 8 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Quoted 8 lines

The whole patch series can be found in one patch at:

	kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.0.9-rc1.gz

and the diffstat can be found below.

thanks,

greg k-h

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

Signature · 5 lines
Shuah Khan
Sr. Linux Kernel Developer
Open Source Innovation Group
Samsung Research America (Silicon Valley)
[email protected] | (970) 217-8978
#60 lore raw
In reply to Greg Kroah-Hartman
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Can you please add commit 0294112ee313 (ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage) to this series too?

It fixes an exsiting regression in earlier 4.0.y.

Thanks,
Rafael

author maintainer
#61 lore raw
Quoted 6 lines · Rafael J. Wysocki
Quoted 5 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Quoted 7 lines
Quoted 2 lines

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Can you please add commit 0294112ee313 (ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage) to this series too?

It fixes an exsiting regression in earlier 4.0.y.

How about I wait for the next 4.0.y, which will be out later this week, as it would be good for people to be able to test this patch out well.

thanks,

greg k-h

#62 lore raw
Quoted 10 lines · Greg Kroah-Hartman
Quoted 9 lines · Rafael J. Wysocki
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.0.9 release. There are 58 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Tue Jul 21 19:08:01 UTC 2015. Anything received after that time might be too late.

Quoted 7 lines
Quoted 4 lines

Can you please add commit 0294112ee313 (ACPI / PNP: Reserve ACPI resources at the fs_initcall_sync stage) to this series too?

It fixes an exsiting regression in earlier 4.0.y.

How about I wait for the next 4.0.y, which will be out later this week, as it would be good for people to be able to test this patch out well.

Yes, that should work too.

Thanks,
Rafael