Skip to contentSkip to conversation

This series implements fastboot on the "bcm28155_ap" boards.

PATCH New Steve Rae 2 participants 5 messages Jul 9, 2015 – Jul 20, 2015

Subsystems (4)
Arm (32-bit) USB Broadcom BCM2711/BCM2835 Arm architecture Broadcom BCM281XX/BCM11XXX/BCM216XX Arm architecture
lore
Share & tools
lore

Steve Rae

author
#0 lore raw

v3 cover This series implements fastboot on the "bcm28155_ap" boards.

The OTG hardware is a DWC2 controller and this series uses the existing gadget driver ("s3c_udc_otg.c").

Changes in v3:
- use static inline functions instead of macros
- update the delay (2ms) to match the kernel code
- use "SZ_1M"
- undefine the 8-bit phy interface

Changes in v2:
- rebased against u-boot-dfu

Jiandong Zheng and Steve Rae (2):
usb: gadget: bcm_udc_otg files
implement Fastboot via USB OTG on bcm28155_ap boards

Steve Rae (1):
g_dnl: add missing declaration

 arch/arm/include/asm/arch-bcm281xx/sysmap.h |  7 ++++
 board/broadcom/bcm28155_ap/bcm28155_ap.c    | 40 ++++++++++++++++++++++
 drivers/usb/gadget/Makefile                 |  1 +
 drivers/usb/gadget/bcm_udc_otg.h            | 22 +++++++++++++
 drivers/usb/gadget/bcm_udc_otg_phy.c        | 51 +++++++++++++++++++++++++++++
 include/configs/bcm28155_ap.h               | 20 +++++++++++
 include/g_dnl.h                             |  1 +
 7 files changed, 142 insertions(+)
 create mode 100644 drivers/usb/gadget/bcm_udc_otg.h
 create mode 100644 drivers/usb/gadget/bcm_udc_otg_phy.c
Signature · 1 line
1.8.5
author
#1 lore raw

PATCH v3 1/3 g_dnl: add missing declaration

Signed-off-by Steve Rae <[email protected]>

---

Changes in v3: None
Changes in v2: None

 include/g_dnl.h | 1 +
 1 file changed, 1 insertion(+)
include/g_dnl.h +1 -0
index 4eeb5e4..ba49f1f 100644
@@ -34,6 +34,7 @@ struct g_dnl_bind_callback {
 };
 
 int g_dnl_bind_fixup(struct usb_device_descriptor *, const char *);
+int g_dnl_get_board_bcd_device_number(int gcnum);
 int g_dnl_board_usb_cable_connected(void);
 int g_dnl_register(const char *s);
 void g_dnl_unregister(void);
Signature · 1 line
1.8.5
author
#2 lore raw

PATCH v3 2/3 usb: gadget: bcm_udc_otg files

In reply to Steve Rae

From: Jiandong Zheng <[email protected]>

Add the required files for the Broadcom UDC OTG interface.

Signed-off-by Jiandong Zheng <[email protected]>
Signed-off-by Steve Rae <[email protected]>

---

Changes in v3:
- use static inline functions instead of macros
- update the delay (2ms) to match the kernel code

Changes in v2: None

 arch/arm/include/asm/arch-bcm281xx/sysmap.h |  7 ++++
 drivers/usb/gadget/bcm_udc_otg.h            | 22 +++++++++++++
 drivers/usb/gadget/bcm_udc_otg_phy.c        | 51 +++++++++++++++++++++++++++++
 3 files changed, 80 insertions(+)
 create mode 100644 drivers/usb/gadget/bcm_udc_otg.h
 create mode 100644 drivers/usb/gadget/bcm_udc_otg_phy.c
arch/arm/include/asm/arch-bcm281xx/sysmap.h +7 -0
index 93ebf34..dbcc88c 100644
@@ -27,4 +27,11 @@
 #define SECWD2_BASE_ADDR	0x35002f40
 #define TIMER_BASE_ADDR		0x3e00d000
 
+#define HSOTG_DCTL_OFFSET					0x00000804
+#define    HSOTG_DCTL_SFTDISCON_MASK				0x00000002
+
+#define HSOTG_CTRL_PHY_P1CTL_OFFSET				0x00000008
+#define    HSOTG_CTRL_PHY_P1CTL_SOFT_RESET_MASK			0x00000002
+#define    HSOTG_CTRL_PHY_P1CTL_NON_DRIVING_MASK		0x00000001
+
 #endif
drivers/usb/gadget/bcm_udc_otg.h new file +22 -0
new file mode 100644
index 0000000..d47aefa
@@ -0,0 +1,22 @@
+/*
+ * Copyright 2015 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __BCM_UDC_OTG_H
+#define __BCM_UDC_OTG_H
+
+#include <common.h>
+
+static inline void wfld_set(uintptr_t addr, uint32_t fld_val, uint32_t fld_mask)
+{
+	writel(((readl(addr) & ~(fld_mask)) | (fld_val)), (addr));
+}
+
+static inline void wfld_clear(uintptr_t addr, uint32_t fld_mask)
+{
+	writel((readl(addr) & ~(fld_mask)), (addr));
+}
+
+#endif
drivers/usb/gadget/bcm_udc_otg_phy.c new file +51 -0

51 lines not on this page · raw message

Signature · 1 line
1.8.5
author
#3 lore raw

PATCH v3 3/3 implement Fastboot via USB OTG on bcm28155_ap boards

In reply to Steve Rae

From: Jiandong Zheng <[email protected]>

Signed-off-by Jiandong Zheng <[email protected]>
Signed-off-by Steve Rae <[email protected]>

---

Changes in v3:
- use "SZ_1M"
- undefine the 8-bit phy interface

Changes in v2:
- rebased against u-boot-dfu

 board/broadcom/bcm28155_ap/bcm28155_ap.c | 40 ++++++++++++++++++++++++++++++++
 drivers/usb/gadget/Makefile              |  1 +
 include/configs/bcm28155_ap.h            | 20 ++++++++++++++++
 3 files changed, 61 insertions(+)
board/broadcom/bcm28155_ap/bcm28155_ap.c +40 -0
index 940a1c2..20eb191 100644
@@ -12,12 +12,20 @@
 #include <asm/kona-common/clk.h>
 #include <asm/arch/sysmap.h>
 
+#include <usb.h>
+#include <usb/s3c_udc.h>
+#include <g_dnl.h>
+
 #define SECWATCHDOG_SDOGCR_OFFSET	0x00000000
 #define SECWATCHDOG_SDOGCR_EN_SHIFT	27
 #define SECWATCHDOG_SDOGCR_SRSTEN_SHIFT	26
 #define SECWATCHDOG_SDOGCR_CLKS_SHIFT	20
 #define SECWATCHDOG_SDOGCR_LD_SHIFT	0
 
+#ifndef CONFIG_USB_SERIALNO
+#define CONFIG_USB_SERIALNO "1234567890"
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /*

@@ -85,3 +93,35 @@ int board_mmc_init(bd_t *bis)
 	return ret;
 }
 #endif
+
+#ifdef CONFIG_USB_GADGET
+static struct s3c_plat_otg_data bcm_otg_data = {
+	.regs_otg	= HSOTG_BASE_ADDR
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+	debug("%s: performing s3c_udc_probe\n", __func__);
+	return s3c_udc_probe(&bcm_otg_data);
+}
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
+{
+	debug("%s\n", __func__);
+	if (!getenv("serial#"))
+		g_dnl_set_serialnumber(CONFIG_USB_SERIALNO);
+	return 0;
+}
+
+int g_dnl_get_board_bcd_device_number(int gcnum)
+{
+	debug("%s\n", __func__);
+	return 1;
+}
+
+int board_usb_cleanup(int index, enum usb_init_type init)
+{
+	debug("%s\n", __func__);
+	return 0;
+}
+#endif
drivers/usb/gadget/Makefile +1 -0
index 4e15323..4c11a7e 100644
@@ -11,6 +11,7 @@ obj-$(CONFIG_USB_ETHER) += epautoconf.o config.o usbstring.o
 # new USB gadget layer dependencies
 ifdef CONFIG_USB_GADGET
 obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o
+obj-$(CONFIG_USB_GADGET_BCM_UDC_OTG_PHY) += bcm_udc_otg_phy.o
 obj-$(CONFIG_USB_GADGET_S3C_UDC_OTG) += s3c_udc_otg.o
 obj-$(CONFIG_USB_GADGET_S3C_UDC_OTG_PHY) += s3c_udc_otg_phy.o
 obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o
include/configs/bcm28155_ap.h +20 -0
index 900dc42..f023f27 100644
@@ -109,6 +109,7 @@
  * for example.
  */
 #define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
 
 /* version string, parser, etc */
 #define CONFIG_VERSION_VARIABLE

@@ -136,4 +137,23 @@
 
 #undef CONFIG_CMD_NFS
 
+/* Fastboot and USB OTG */
+#define CONFIG_USB_FUNCTION_FASTBOOT
+#define CONFIG_CMD_FASTBOOT
+#define CONFIG_FASTBOOT_FLASH
+#define CONFIG_FASTBOOT_FLASH_MMC_DEV	0
+#define CONFIG_SYS_CACHELINE_SIZE	64
+#define CONFIG_USB_FASTBOOT_BUF_SIZE	(CONFIG_SYS_SDRAM_SIZE - SZ_1M)
+#define CONFIG_USB_FASTBOOT_BUF_ADDR	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW	0
+#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_BCM_UDC_OTG_PHY
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_USBID_ADDR		0x34052c46
+#define CONFIG_G_DNL_VENDOR_NUM		0x18d1	/* google */
+#define CONFIG_G_DNL_PRODUCT_NUM	0x0d02	/* nexus one */
+#define CONFIG_G_DNL_MANUFACTURER	"Broadcom Corporation"
+
 #endif /* __BCM28155_AP_H */
Signature · 1 line
1.8.5
#4 lore raw

v3 cover This series implements fastboot on the "bcm28155_ap" boards.

In reply to Steve Rae

Hi Steve,

Quoted 24 lines

The OTG hardware is a DWC2 controller and this series uses the existing gadget driver ("s3c_udc_otg.c").

Changes in v3:
- use static inline functions instead of macros
- update the delay (2ms) to match the kernel code
- use "SZ_1M"
- undefine the 8-bit phy interface

Changes in v2:
- rebased against u-boot-dfu

Jiandong Zheng and Steve Rae (2):
usb: gadget: bcm_udc_otg files
implement Fastboot via USB OTG on bcm28155_ap boards

Steve Rae (1):
g_dnl: add missing declaration

 arch/arm/include/asm/arch-bcm281xx/sysmap.h |  7 ++++
 board/broadcom/bcm28155_ap/bcm28155_ap.c    | 40
++++++++++++++++++++++ drivers/usb/gadget/Makefile                 |
1 + drivers/usb/gadget/bcm_udc_otg.h            | 22 +++++++++++++
 drivers/usb/gadget/bcm_udc_otg_phy.c        | 51
Quoted 6 lines

+++++++++++++++++++++++++++++
include/configs/bcm28155_ap.h | 20 +++++++++++
include/g_dnl.h | 1 + 7 files changed,
142 insertions(+) create mode 100644 drivers/usb/gadget/bcm_udc_otg.h

 create mode 100644 drivers/usb/gadget/bcm_udc_otg_phy.c

Applied to u-boot-dfu (the whole series).

Thanks for patches!

Signature · 5 lines
Best regards,

Lukasz Majewski

Samsung R&D Institute Poland (SRPOL) | Linux Platform Group