Add support for touchscreen on Colibri VF50

Add device tree node for touchscreen support on Colibri VF50. The touchscreen functionality on VF50 uses the ADC channels of Vybrid and some GPIOs. Also add pinctrl nodes for proper pinmux.

Signed-off-by Sanchayan Maity <[email protected]>

---
 arch/arm/boot/dts/vf500-colibri-eval-v3.dts |  5 +++
 arch/arm/boot/dts/vf500-colibri.dtsi        | 47 +++++++++++++++++++++++++++++
 2 files changed, 52 insertions(+)

arch/arm/boot/dts/vf500-colibri-eval-v3.dts +5 -0

index 7fc782c..c3173fc 100644
@@ -15,3 +15,8 @@
 	model = "Toradex Colibri VF50 on Colibri Evaluation Board";
 	compatible = "toradex,vf500-colibri_vf50-on-eval", "toradex,vf500-colibri_vf50", "fsl,vf500";
 };
+
+&touchscreen {
+	vf50-ts-min-pressure = <200>;
+	status = "okay";
+};

arch/arm/boot/dts/vf500-colibri.dtsi +47 -0

index cee34a3..84f091d 100644
@@ -17,4 +17,51 @@
 	memory {
 		reg = <0x80000000 0x8000000>;
 	};
+
+	touchscreen: vf50-touchscreen {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 0>,<&adc0 0>,
+				<&adc0 1>,<&adc1 2>;
+		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default","gpios";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>;
+		pinctrl-1 = <&pinctrl_touchctrl_default>;
+		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	vf610-colibri {
+		pinctrl_touchctrl_idle: touchctrl_idle {
+			fsl,pins = <
+				VF610_PAD_PTA18__GPIO_8		0x006d
+				VF610_PAD_PTA19__GPIO_9		0x006c
+				>;
+		};
+
+		pinctrl_touchctrl_default: touchctrl_default {
+			fsl,pins = <
+				VF610_PAD_PTA18__ADC0_SE0	0x0040
+				VF610_PAD_PTA19__ADC0_SE1	0x0040
+				VF610_PAD_PTA16__ADC1_SE0	0x0040
+				VF610_PAD_PTB2__ADC1_SE2	0x0040
+				>;
+		};
+
+		pinctrl_touchctrl_gpios: touchctrl_gpios {
+			fsl,pins = <
+				VF610_PAD_PTA23__GPIO_13	0x22e9
+				VF610_PAD_PTB23__GPIO_93	0x22e9
+				VF610_PAD_PTA22__GPIO_12	0x22e9
+				VF610_PAD_PTA11__GPIO_4		0x22e9
+				>;
+		};
+	};
 };

Signature · 1 line

2.5.0

Add device tree node for touchscreen support on Colibri VF50. The touchscreen functionality on VF50 uses the ADC channels of Vybrid and some GPIOs. Also add pinctrl nodes for proper pinmux.

Signed-off-by Sanchayan Maity <[email protected]>

The Colibri Vybrid VF50 module supports 4-wire touchscreens using FETs and ADC inputs. This driver uses the IIO consumer interface and relies on the vf610_adc driver based on the IIO framework.

Signed-off-by Sanchayan Maity <[email protected]>

---
 drivers/input/touchscreen/Kconfig           |  12 +
 drivers/input/touchscreen/Makefile          |   1 +
 drivers/input/touchscreen/colibri-vf50-ts.c | 381 ++++++++++++++++++++++++++++
 3 files changed, 394 insertions(+)
 create mode 100644 drivers/input/touchscreen/colibri-vf50-ts.c

drivers/input/touchscreen/Kconfig +12 -0

index 80f6386..28948ca 100644
@@ -1027,4 +1027,16 @@ config TOUCHSCREEN_ZFORCE
 	  To compile this driver as a module, choose M here: the
 	  module will be called zforce_ts.
 
+config TOUCHSCREEN_COLIBRI_VF50
+	tristate "Toradex Colibri on board touchscreen driver"
+	depends on GPIOLIB && IIO && VF610_ADC
+	help
+	  Say Y here if you have a Colibri VF50 and plan to use
+	  the on-board provided 4-wire touchscreen driver.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called colibri_vf50_ts.
+
 endif

drivers/input/touchscreen/Makefile +1 -0

index 44deea7..93746a0 100644
@@ -84,3 +84,4 @@ obj-$(CONFIG_TOUCHSCREEN_W90X900)	+= w90p910_ts.o
 obj-$(CONFIG_TOUCHSCREEN_SX8654)	+= sx8654.o
 obj-$(CONFIG_TOUCHSCREEN_TPS6507X)	+= tps6507x-ts.o
 obj-$(CONFIG_TOUCHSCREEN_ZFORCE)	+= zforce_ts.o
+obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50)	+= colibri-vf50-ts.o

drivers/input/touchscreen/colibri-vf50-ts.c new file +381 -0

new file mode 100644
index 0000000..26187e0
@@ -0,0 +1,381 @@
+/* Copyright 2015 Toradex AG
+ *
+ * Toradex Colibri VF50 Touchscreen driver
+ *
+ * Originally authored by Stefan Agner for 3.0 kernel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/iio/consumer.h>
+#include <linux/iio/types.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define DRIVER_NAME "colibri-vf50-ts"
+#define DRV_VERSION "1.0"
+
+#define VF_ADC_MAX ((1 << 12) - 1)
+
+#define COLI_TOUCH_MIN_DELAY_US 1000
+#define COLI_TOUCH_MAX_DELAY_US 2000
+#define COLI_TOUCH_NO_OF_AVGS	5
+#define COLI_TOUCH_REQ_ADC_CHAN	4
+
+struct vf50_touch_device {
+	struct platform_device	*pdev;
+	struct input_dev	*ts_input;
+	struct iio_channel	*channels;
+	struct gpio_desc *gpio_xp;
+	struct gpio_desc *gpio_xm;
+	struct gpio_desc *gpio_yp;
+	struct gpio_desc *gpio_ym;
+	int pen_irq;
+	int min_pressure;
+	bool stop_touchscreen;
+};
+
+/*
+ * Enables given plates and measures touch parameters using ADC
+ */
+static int adc_ts_measure(struct iio_channel *channel,
+		  struct gpio_desc *plate_p, struct gpio_desc *plate_m)
+{
+	int i, value = 0, val = 0;
+	int ret;
+
+	gpiod_set_value(plate_p, 1);
+	gpiod_set_value(plate_m, 1);
+
+	usleep_range(COLI_TOUCH_MIN_DELAY_US, COLI_TOUCH_MAX_DELAY_US);
+
+	for (i = 0; i < COLI_TOUCH_NO_OF_AVGS; i++) {
+		ret = iio_read_channel_raw(channel, &val);
+		if (ret < 0) {
+			value = ret;
+			goto error_iio_read;
+		}
+
+		value += val;
+	}
+
+	value /= COLI_TOUCH_NO_OF_AVGS;
+
+error_iio_read:
+	gpiod_set_value(plate_p, 0);
+	gpiod_set_value(plate_m, 0);
+
+	return value;
+}
+
+/*
+ * Enable touch detection using falling edge detection on XM
+ */
+static void vf50_ts_enable_touch_detection(struct vf50_touch_device *vf50_ts)
+{
+	/* Enable plate YM (needs to be strong GND, high active) */
+	gpiod_set_value(vf50_ts->gpio_ym, 1);
+
+	/*
+	 * Let the platform mux to idle state in order to enable
+	 * Pull-Up on GPIO
+	 */
+	pinctrl_pm_select_idle_state(&vf50_ts->pdev->dev);
+}
+
+/*
+ * ADC touch screen sampling bottom half irq handler
+ */
+static irqreturn_t vf50_ts_irq_bh(int irq, void *private)
+{
+	struct vf50_touch_device *vf50_ts = private;
+	struct device *dev = &vf50_ts->pdev->dev;
+	int val_x, val_y, val_z1, val_z2, val_p = 0;
+	bool discard_val_on_start = true;
+
+	/* Disable the touch detection plates */
+	gpiod_set_value(vf50_ts->gpio_ym, 0);
+
+	/* Let the platform mux to default state in order to mux as ADC */
+	pinctrl_pm_select_default_state(dev);
+
+	while (!vf50_ts->stop_touchscreen) {
+		/* X-Direction */
+		val_x = adc_ts_measure(&vf50_ts->channels[0],
+				vf50_ts->gpio_xp, vf50_ts->gpio_xm);
+		if (val_x < 0)
+			break;
+
+		/* Y-Direction */
+		val_y = adc_ts_measure(&vf50_ts->channels[1],
+				vf50_ts->gpio_yp, vf50_ts->gpio_ym);
+		if (val_y < 0)
+			break;
+
+		/*
+		 * Touch pressure
+		 * Measure on XP/YM
+		 */
+		val_z1 = adc_ts_measure(&vf50_ts->channels[2],
+				vf50_ts->gpio_yp, vf50_ts->gpio_xm);
+		if (val_z1 < 0)
+			break;
+		val_z2 = adc_ts_measure(&vf50_ts->channels[3],
+				vf50_ts->gpio_yp, vf50_ts->gpio_xm);
+		if (val_z2 < 0)
+			break;
+
+		/* Validate signal (avoid calculation using noise) */
+		if (val_z1 > 64 && val_x > 64) {
+			/*
+			 * Calculate resistance between the plates
+			 * lower resistance means higher pressure
+			 */
+			int r_x = (1000 * val_x) / VF_ADC_MAX;
+
+			val_p = (r_x * val_z2) / val_z1 - r_x;
+
+		} else {
+			val_p = 2000;
+		}
+
+		val_p = 2000 - val_p;
+		dev_dbg(dev, "Measured values: x: %d, y: %d, z1: %d, z2: %d, "
+			"p: %d\n", val_x, val_y, val_z1, val_z2, val_p);
+
+		/*
+		 * If touch pressure is too low, stop measuring and reenable
+		 * touch detection
+		 */
+		if (val_p < vf50_ts->min_pressure || val_p > 2000)
+			break;
+
+		/*
+		 * The pressure may not be enough for the first x and the
+		 * second y measurement, but, the pressure is ok when the
+		 * driver is doing the third and fourth measurement. To
+		 * take care of this, we drop the first measurement always.
+		 */
+		if (discard_val_on_start) {
+			discard_val_on_start = false;
+		} else {
+			/*
+			 * Report touch position and sleep for
+			 * next measurement
+			 */
+			input_report_abs(vf50_ts->ts_input,
+					ABS_X, VF_ADC_MAX - val_x);
+			input_report_abs(vf50_ts->ts_input,
+					ABS_Y, VF_ADC_MAX - val_y);
+			input_report_abs(vf50_ts->ts_input,
+					ABS_PRESSURE, val_p);
+			input_report_key(vf50_ts->ts_input, BTN_TOUCH, 1);
+			input_sync(vf50_ts->ts_input);
+		}
+
+		msleep(10);
+	}
+
+	/* Report no more touch, reenable touch detection */
+	input_report_abs(vf50_ts->ts_input, ABS_PRESSURE, 0);
+	input_report_key(vf50_ts->ts_input, BTN_TOUCH, 0);
+	input_sync(vf50_ts->ts_input);
+
+	vf50_ts_enable_touch_detection(vf50_ts);
+
+	/* Wait for the pull-up to be stable on high */
+	msleep(10);
+
+	return IRQ_HANDLED;
+}
+
+static int vf50_ts_open(struct input_dev *dev_input)
+{
+	struct vf50_touch_device *touchdev = input_get_drvdata(dev_input);
+	struct device *dev = &touchdev->pdev->dev;
+
+	dev_dbg(dev, "Input device %s opened, starting touch detection\n",
+			dev_input->name);
+
+	touchdev->stop_touchscreen = false;
+
+	/* Mux detection before request IRQ, wait for pull-up to settle */
+	vf50_ts_enable_touch_detection(touchdev);
+	msleep(10);
+
+	return 0;
+}
+
+static void vf50_ts_close(struct input_dev *dev_input)
+{
+	struct vf50_touch_device *touchdev = input_get_drvdata(dev_input);
+	struct device *dev = &touchdev->pdev->dev;
+
+	touchdev->stop_touchscreen = true;
+
+	/* Make sure IRQ is not running past close */
+	mb();
+	synchronize_irq(touchdev->pen_irq);
+
+	gpiod_set_value(touchdev->gpio_ym, 0);
+	pinctrl_pm_select_default_state(dev);
+
+	dev_dbg(dev, "Input device %s closed, disable touch detection\n",
+		dev_input->name);
+}
+
+static int vf50_ts_get_gpiod(struct device *dev,
+	struct gpio_desc **gpio_d, const char *con_id, enum gpiod_flags flags)
+{
+	int error;
+
+	*gpio_d = devm_gpiod_get(dev, con_id, flags);
+	if (IS_ERR(*gpio_d)) {
+		error = PTR_ERR(*gpio_d);
+		dev_err(dev, "Could not get gpio_%s %d\n", con_id, error);
+		return error;
+	}
+
+	return 0;
+}
+
+static void vf50_ts_channel_release(void *data)
+{
+	struct iio_channel *channels = data;
+
+	iio_channel_release_all(channels);
+}
+
+static int vf50_ts_probe(struct platform_device *pdev)
+{
+	struct input_dev *input;
+	struct iio_channel *channels;
+	struct device *dev = &pdev->dev;
+	struct vf50_touch_device *touchdev;
+	int num_adc_channels = 0;
+	int error;
+
+	channels = iio_channel_get_all(dev);
+	if (IS_ERR(channels))
+		return PTR_ERR(channels);
+
+	error = devm_add_action(dev, vf50_ts_channel_release, channels);
+	if (error) {
+		iio_channel_release_all(channels);
+		dev_err(dev, "Failed to register iio channel release action");
+		return error;
+	}
+
+	touchdev = devm_kzalloc(dev, sizeof(*touchdev), GFP_KERNEL);
+	if (!touchdev)
+		return -ENOMEM;
+
+	touchdev->pdev = pdev;
+	touchdev->channels = channels;
+
+	while (channels[num_adc_channels].indio_dev)
+		num_adc_channels++;
+
+	if (num_adc_channels != COLI_TOUCH_REQ_ADC_CHAN) {
+		dev_err(dev, "Inadequate ADC channels specified\n");
+		return -EINVAL;
+	}
+
+	error = of_property_read_u32(dev->of_node, "vf50-ts-min-pressure",
+				 &touchdev->min_pressure);
+	if (error)
+		return error;
+
+	input = devm_input_allocate_device(dev);
+	if (!input) {
+		dev_err(dev, "Failed to allocate TS input device\n");
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, touchdev);
+
+	input->name = DRIVER_NAME;
+	input->id.bustype = BUS_HOST;
+	input->dev.parent = dev;
+	input->open = vf50_ts_open;
+	input->close = vf50_ts_close;
+
+	input_set_capability(input, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(input, ABS_X, 0, VF_ADC_MAX, 0, 0);
+	input_set_abs_params(input, ABS_Y, 0, VF_ADC_MAX, 0, 0);
+	input_set_abs_params(input, ABS_PRESSURE, 0, VF_ADC_MAX, 0, 0);
+
+	touchdev->ts_input = input;
+	input_set_drvdata(input, touchdev);
+	error = input_register_device(input);
+	if (error) {
+		dev_err(dev, "Failed to register input device\n");
+		return error;
+	}
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_xp,
+				"xp", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_xm,
+				"xm", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_yp,
+				"yp", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_ym,
+				"ym", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	touchdev->pen_irq = platform_get_irq(pdev, 0);
+	if (touchdev->pen_irq < 0)
+		return touchdev->pen_irq;
+
+	error = devm_request_threaded_irq(dev, touchdev->pen_irq, NULL,
+			vf50_ts_irq_bh, IRQF_ONESHOT,
+			"vf50 touch", touchdev);
+	if (error < 0)
+		return error;
+
+	return 0;
+}
+
+static const struct of_device_id vf50_touch_of_match[] = {
+	{ .compatible = "toradex,vf50-touchscreen", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, vf50_touch_of_match);
+
+static struct platform_driver vf50_touch_driver = {
+	.driver = {
+		.name = "toradex,vf50_touchctrl",
+		.of_match_table = vf50_touch_of_match,
+	},
+	.probe = vf50_ts_probe,
+};
+
+module_platform_driver(vf50_touch_driver);
+
+MODULE_AUTHOR("Sanchayan Maity");
+MODULE_DESCRIPTION("Colibri VF50 Touchscreen driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);

Signature · 6 lines

2.5.0

--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html