Skip to contentSkip to conversation

clk: imx: increase AXI clock rate to 264MHz for i.MX6UL

PATCH New Anson Huang 2 participants 2 messages Aug 6, 2015 – Sep 6, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 clk: imx: increase AXI clock rate to 264MHz for i.MX6UL

On i.MX6UL, AXI clock rate's design target is 264MHz, but by default it is only set to 198MHz which is NOT good enough for performance, this patch increases AXI clock rate from 198MHz to 264MHz to meet the design target, this is done by switching its parent clock "periph" from 396MHz PFD to 528MHz PLL.

---
 drivers/clk/imx/clk-imx6ul.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/clk/imx/clk-imx6ul.c +18 -0
index aaa3665..01718d0 100644
@@ -407,6 +407,24 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
 	clk_data.clk_num = ARRAY_SIZE(clks);
 	of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
 
+	/*
+	 * Lower the AHB clock rate before changing the parent clock source,
+	 * as AHB clock rate can NOT be higher than 133MHz, but its parent
+	 * will be switched from 396MHz PFD to 528MHz PLL in order to increase
+	 * AXI clock rate, so we need to lower AHB rate first to make sure at
+	 * any time, AHB rate is <= 133MHz.
+	 */
+	clk_set_rate(clks[IMX6UL_CLK_AHB], 99000000);
+
+	/* Change periph_pre clock to pll2_bus to adjust AXI rate to 264MHz */
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH_CLK2_SEL], clks[IMX6UL_CLK_PLL3_USB_OTG]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH], clks[IMX6UL_CLK_PERIPH_CLK2]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH_PRE], clks[IMX6UL_CLK_PLL2_BUS]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH], clks[IMX6UL_CLK_PERIPH_PRE]);
+
+	/* Make sure AHB rate is 132MHz  */
+	clk_set_rate(clks[IMX6UL_CLK_AHB], 132000000);
+
 	/* set perclk to from OSC */
 	clk_set_parent(clks[IMX6UL_CLK_PERCLK_SEL], clks[IMX6UL_CLK_OSC]);
 
Signature · 1 line
1.9.1
Applied
#1 lore raw

PATCH 1/1 clk: imx: increase AXI clock rate to 264MHz for i.MX6UL

Quoted 7 lines · Anson Huang

On i.MX6UL, AXI clock rate's design target is 264MHz, but by default it is only set to 198MHz which is NOT good enough for performance, this patch increases AXI clock rate from 198MHz to 264MHz to meet the design target, this is done by switching its parent clock "periph" from 396MHz PFD to 528MHz PLL.

Applied, thanks.

But please remember to copy not only linux-clk list but also clk maintainers Michael and Stephen for future i.MX clock patches.

Shawn

Quoted 36 lines
---
 drivers/clk/imx/clk-imx6ul.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/clk/imx/clk-imx6ul.c +18 -0
index aaa3665..01718d0 100644
@@ -407,6 +407,24 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
 	clk_data.clk_num = ARRAY_SIZE(clks);
 	of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
 
+	/*
+	 * Lower the AHB clock rate before changing the parent clock source,
+	 * as AHB clock rate can NOT be higher than 133MHz, but its parent
+	 * will be switched from 396MHz PFD to 528MHz PLL in order to increase
+	 * AXI clock rate, so we need to lower AHB rate first to make sure at
+	 * any time, AHB rate is <= 133MHz.
+	 */
+	clk_set_rate(clks[IMX6UL_CLK_AHB], 99000000);
+
+	/* Change periph_pre clock to pll2_bus to adjust AXI rate to 264MHz */
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH_CLK2_SEL], clks[IMX6UL_CLK_PLL3_USB_OTG]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH], clks[IMX6UL_CLK_PERIPH_CLK2]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH_PRE], clks[IMX6UL_CLK_PLL2_BUS]);
+	clk_set_parent(clks[IMX6UL_CLK_PERIPH], clks[IMX6UL_CLK_PERIPH_PRE]);
+
+	/* Make sure AHB rate is 132MHz  */
+	clk_set_rate(clks[IMX6UL_CLK_AHB], 132000000);
+
 	/* set perclk to from OSC */
 	clk_set_parent(clks[IMX6UL_CLK_PERCLK_SEL], clks[IMX6UL_CLK_OSC]);
 
Signature · 1 line
1.9.1