at91sam9 Main crystal frequency problems
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)
I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day) Why is it that the frequency of Crystal is not found ?
I attached my DT, and kernel prints.
Thanks for your help.
Signature · 256 lines
Antoine Aubert
a.aubert at overkiz.com
-------------- next part --------------
ll /proc/device-tree/clocks/*
-r--r--r-- 1 root root 7 Sep 7 09:13 /proc/device-tree/clocks/name
/proc/device-tree/clocks/adc_op_clk:
-r--r--r-- 1 root root 4 Sep 7 09:14 #clock-cells
-r--r--r-- 1 root root 4 Sep 7 09:14 clock-frequency
-r--r--r-- 1 root root 12 Sep 7 09:14 compatible
-r--r--r-- 1 root root 4 Sep 7 09:14 linux,phandle
-r--r--r-- 1 root root 11 Sep 7 09:14 name
-r--r--r-- 1 root root 4 Sep 7 09:14 phandle
/proc/device-tree/clocks/main_xtal:
-r--r--r-- 1 root root 4 Sep 7 09:14 #clock-cells
-r--r--r-- 1 root root 4 Sep 7 09:14 clock-frequency
-r--r--r-- 1 root root 12 Sep 7 09:14 compatible
-r--r--r-- 1 root root 4 Sep 7 09:14 linux,phandle
-r--r--r-- 1 root root 10 Sep 7 09:14 name
-r--r--r-- 1 root root 4 Sep 7 09:14 phandle
/proc/device-tree/clocks/slow_xtal:
-r--r--r-- 1 root root 4 Sep 7 09:14 #clock-cells
-r--r--r-- 1 root root 4 Sep 7 09:14 clock-frequency
-r--r--r-- 1 root root 12 Sep 7 09:14 compatible
-r--r--r-- 1 root root 4 Sep 7 09:14 linux,phandle
-r--r--r-- 1 root root 10 Sep 7 09:14 name
-r--r--r-- 1 root root 4 Sep 7 09:14 phandle
-------------- next part --------------
cat /sys/kernel/debug/clk/clk_summary
clock enable_cnt prepare_cnt rate accuracy phase
----------------------------------------------------------------------------------------
slow_xtal 0 0 32768 0 0
slow_osc 0 0 32768 0 0
main_xtal 1 1 12000000 0 0
main_osc 1 1 12000000 0 0
mainck 2 2 12000000 0 0
utmick 2 2 480000000 0 0
usbck 2 2 48000000 0 0
udpck 0 0 48000000 0 0
uhpck 1 1 48000000 0 0
pllack 1 1 800000000 0 0
plladivck 1 1 400000000 0 0
smdclk 0 0 400000000 0 0
smdck 0 0 400000000 0 0
masterck 11 11 133333333 0 0
ddrck 1 1 133333333 0 0
usart3_clk 0 0 133333333 0 0
usart2_clk 0 0 133333333 0 0
usart1_clk 0 0 133333333 0 0
usart0_clk 1 1 133333333 0 0
uhphs_clk 3 3 133333333 0 0
udphs_clk 0 0 133333333 0 0
uart1_clk 0 0 133333333 0 0
uart0_clk 0 0 133333333 0 0
twi2_clk 0 0 133333333 0 0
twi1_clk 0 0 133333333 0 0
twi0_clk 0 0 133333333 0 0
tcb0_clk 2 2 133333333 0 0
ssc0_clk 0 0 133333333 0 0
spi1_clk 0 0 133333333 0 0
spi0_clk 0 0 133333333 0 0
smd_clk 0 0 133333333 0 0
pwm_clk 2 1 133333333 0 0
pioCD_clk 2 2 133333333 0 0
pioAB_clk 2 2 133333333 0 0
mci1_clk 0 0 133333333 0 0
mci0_clk 0 0 133333333 0 0
macb0_clk 2 2 133333333 0 0
dma1_clk 1 1 133333333 0 0
dma0_clk 1 1 133333333 0 0
adc_clk 0 0 133333333 0 0
adc_op_clk 0 0 5000000 0 0
slow_rc_osc 1 1 32768 50000000 0
slck 1 1 32768 50000000 0
prog0 0 0 32768 50000000 0
pck0 0 0 32768 50000000 0
prog1 0 0 32768 50000000 0
pck1 0 0 32768 50000000 0
main_rc_osc 0 0 12000000 50000000 0
-------------- next part --------------
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.0.4 (antoine at compile-embedded) (gcc version 4.9.1 (GCC) ) #1 Thu Sep 3 09:25:30 CEST 2015
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Overkiz Kizbox mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] AT91: Detected soc type: at91sam9x5
[ 0.000000] AT91: Detected soc subtype: at91sam9g25
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c03dabac, node_mem_map c7ef9000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: panic=5 root=ubi0:root rootfstype=ubifs rw ubi.mtd=ubi console=ttyS0,115200 earlyprintk
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 125616K/131072K available (2698K kernel code, 133K rwdata, 988K rodata, 128K init, 194K bss, 5456K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc03a1f54 (3688 kB)
[ 0.000000] .init : 0xc03a2000 - 0xc03c2000 ( 128 kB)
[ 0.000000] .data : 0xc03c2000 - 0xc03e37c0 ( 134 kB)
[ 0.000000] .bss : 0xc03e37c0 - 0xc0414394 ( 195 kB)
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Main crystal frequency not set, using approximate value
[ 0.000000] master clk is overclocked
[ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns
[ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)
[ 0.070312] pid_max: default: 32768 minimum: 301
[ 0.078125] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085937] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.093750] CPU: Testing write buffer coherency: ok
[ 0.101562] Setting up static identity map for 0x20290e20 - 0x20290e9c
[ 0.109375] devtmpfs: initialized
[ 0.117187] pinctrl core: initialized pinctrl subsystem
[ 0.148437] NET: Registered protocol family 16
[ 0.156250] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.179687] AT91: Power Management
[ 0.187500] gpio-at91 fffff400.gpio: at address fefff400
[ 0.195312] gpio-at91 fffff600.gpio: at address fefff600
[ 0.203125] gpio-at91 fffff800.gpio: at address fefff800
[ 0.210937] gpio-at91 fffffa00.gpio: at address fefffa00
[ 0.218750] pinctrl-at91 ahb:apb:pinctrl at fffff400: initialized AT91 pinctrl driver
[ 0.226562] tcb_clksrc: tc0 at 16.166 MHz
[ 0.265625] at_hdmac ffffec00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
[ 0.281250] at_hdmac ffffee00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
[ 0.296875] usbcore: registered new interface driver usbfs
[ 0.296875] usbcore: registered new interface driver hub
[ 0.304687] usbcore: registered new device driver usb
[ 0.312500] Switched to clocksource tcb_clksrc
[ 0.335937] NET: Registered protocol family 2
[ 0.335937] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.343750] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.351562] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.359375] TCP: reno registered
[ 0.359375] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.367187] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.375000] NET: Registered protocol family 1
[ 0.382812] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.390625] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.398437] io scheduler noop registered (default)
[ 0.406250] f801c000.serial: ttyS1 at MMIO 0xf801c000 (irq = 30, base_baud = 8333333) is a ATMEL_SERIAL
[ 0.414062] fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 16, base_baud = 8333333) is a ATMEL_SERIAL
[ 0.421875] console [ttyS0] enabled
[ 0.429687] bootconsole [earlycon0] disabled
[ 0.453125] brd: module loaded
[ 0.476562] loop: module loaded
[ 0.492187] atmel_nand 40000000.nand: Use On Flash BBT
[ 0.492187] atmel_nand 40000000.nand: Using dma0chan0 for DMA transfers.
[ 0.500000] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.507812] nand: AMD/Spansion S34ML01G2
[ 0.507812] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.515625] atmel_nand 40000000.nand: minimum ECC: 4 bits in 512 bytes
[ 0.523437] atmel_nand 40000000.nand: Initialize PMECC params, cap: 4, sector: 512
[ 0.531250] Bad block table found at page 65472, version 0x01
[ 0.539062] Bad block table found at page 65408, version 0x01
[ 0.546875] 2 ofpart partitions found on MTD device atmel_nand
[ 0.546875] Creating 2 MTD partitions on "atmel_nand":
[ 0.554687] 0x000000000000-0x000000020000 : "bootstrap"
[ 0.562500] 0x000000020000-0x000008000000 : "ubi"
[ 0.578125] macb f802c000.ethernet (unnamed net_device) (uninitialized): invalid hw address, using random
[ 0.585937] libphy: MACB_mii_bus: probed
[ 0.671875] macb f802c000.ethernet eth0: Cadence MACB rev 0x0001010c at 0xf802c000 irq 26 (0a:90:3d:11:5b:1c)
[ 0.679687] macb f802c000.ethernet eth0: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f802c000.etherne:01, irq=-1)
[ 0.687500] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.695312] ehci-atmel: EHCI Atmel driver
[ 0.695312] atmel-ehci 700000.ehci: EHCI Host Controller
[ 0.703125] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 0.710937] atmel-ehci 700000.ehci: irq 32, io mem 0x00700000
[ 0.734375] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 0.734375] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.742187] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.750000] usb usb1: Product: EHCI Host Controller
[ 0.750000] usb usb1: Manufacturer: Linux 4.0.4 ehci_hcd
[ 0.757812] usb usb1: SerialNumber: 700000.ehci
[ 0.765625] hub 1-0:1.0: USB hub found
[ 0.765625] hub 1-0:1.0: 3 ports detected
[ 0.773437] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.781250] ohci-atmel: OHCI Atmel driver
[ 0.781250] at91_ohci 600000.ohci: USB Host Controller
[ 0.789062] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[ 0.796875] at91_ohci 600000.ohci: irq 32, io mem 0x00600000
[ 0.859375] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.867187] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.875000] usb usb2: Product: USB Host Controller
[ 0.875000] usb usb2: Manufacturer: Linux 4.0.4 ohci_hcd
[ 0.882812] usb usb2: SerialNumber: at91
[ 0.890625] hub 2-0:1.0: USB hub found
[ 0.890625] hub 2-0:1.0: 1 port detected
[ 0.898437] AT91: Starting after general reset
[ 0.906250] at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=1)
[ 0.914062] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.914062] usbcore: registered new interface driver usbhid
[ 0.921875] usbhid: USB HID core driver
[ 0.929687] TCP: cubic registered
[ 0.929687] NET: Registered protocol family 17
[ 0.945312] ubi0: attaching mtd1
[ 1.343750] ubi0: scanning is finished
[ 1.367187] ubi0: attached mtd1 (name "ubi", size 127 MiB)
[ 1.375000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.382812] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.390625] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.390625] ubi0: good PEBs: 1019, bad PEBs: 4, corrupted PEBs: 0
[ 1.398437] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[ 1.406250] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 288141040
[ 1.414062] ubi0: available PEBs: 102, total reserved PEBs: 917, PEBs reserved for bad PEB handling: 16
[ 1.421875] ubi0: background thread "ubi_bgt0d" started, PID 292
[ 1.468750] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 1.500000] UBIFS: background thread "ubifs_bgt0_7" started, PID 351
[ 1.515625] UBIFS: recovery needed
[ 1.593750] UBIFS: recovery completed
[ 1.593750] UBIFS: mounted UBI device 0, volume 7, name "root"
[ 1.601562] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.609375] UBIFS: FS size: 49393664 bytes (47 MiB, 389 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.617187] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.617187] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 778BA019-0C14-4BE8-857A-A31BF387B571, small LPT model
[ 1.625000] VFS: Mounted root (ubifs filesystem) on device 0:13.
[ 1.632812] devtmpfs: mounted
[ 1.632812] Freeing unused kernel memory: 128K (c03a2000 - c03c2000)
[ 2.695312] random: dd urandom read with 54 bits of entropy available
[ 3.000000] UBIFS: background thread "ubifs_bgt0_8" started, PID 415
[ 3.023437] UBIFS: recovery needed
[ 3.148437] UBIFS: recovery completed
[ 3.148437] UBIFS: mounted UBI device 0, volume 8, name "apps"
[ 3.156250] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 3.164062] UBIFS: FS size: 49393664 bytes (47 MiB, 389 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 3.171875] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 3.171875] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B11D014C-5838-40FE-AE66-E6FAE0EC2398, small LPT model
[ 5.671875] macb f802c000.ethernet eth0: link up (100/Full)
[ 10.914062] random: nonblocking pool is initialized
-------------- next part --------------
A non-text attachment was scrubbed...
Name: at91-kizboxmini.dts
Type: audio/vnd.dts
Size: 2484 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150907/06bcf6f1/attachment-0001.dts>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150907/06bcf6f1/attachment-0001.sig>Hi Antoine,
Quoted 8 lines · On Mon, 7 Sep 2015 09:31:07 +0200 Antoine Aubert <[email protected]> wrote:
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
Quoted 8 lines
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
According to your clk_summary dump that's not the case.
Quoted 3 lines
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day)
I'd say no, but could you tell me more about your watchdog issues.
Quoted 1 line
Why is it that the frequency of Crystal is not found ?
That's a good question, and honestly I don't. Everything seems to be defined properly in your device tree.
Could you add some traces in the fixed-rate clk driver [1] to see if the main_xtal is correctly registered and if its registration occurs before the main_osc registration?
Best Regards,
Boris
Signature · 3 lines
Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
Hi Boris,
Thank you for your help. I have some news thanks to traces in clk driver.
Le 08/09/2015 18:12, Boris Brezillon a ?crit :
Quoted 22 lines
Hi Antoine,
Quoted 8 lines · On Mon, 7 Sep 2015 09:31:07 +0200 Antoine Aubert <[email protected]> wrote:
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
Quoted 8 lines
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
Quoted 7 lines
According to your
clk_summarydump that's not the case.Quoted 3 lines
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day)I'd say no, but could you tell me more about your watchdog issues.
Yet, we did not take the analysis. We just observed these resets.
But, I found a clue:
We recently removed the slow clock to the PCB. I forgot to disabled the slow_xtal. :/
Can there be a link ? (I think so...)
Quoted 9 lines
Quoted 2 lines
Why is it that the frequency of Crystal is not found ?
That's a good question, and honestly I don't. Everything seems to be defined properly in your device tree.
Could you add some traces in the fixed-rate clk driver [1] to see if the
main_xtalis correctly registered and if its registration occurs before themain_oscregistration?
On our board, there is two kernel boot phases.
First, we boot from at91-bootstrap.
Second we launched kexec with an other kernel.
I found that the device tree is well loaded from the at91-bootstrap. Any crystal issues. But, on kexec --exec, (with the same kernel) those issues appears. (see dmesg attached)
If I launch kexec with --dtb, it's working ...
I thought kexec keep old dtb. Was I wrong ?
Quoted 7 lines
Best Regards,
Boris
Best regards,
Antoine Aubert
a.aubert at overkiz.com
-------------- next part --------------
[ 187.421875] kexec: Starting new kernel
[ 187.421875] Bye!
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.0.4 (antoine at compile-embedded) (gcc version 4.9.1 (GCC) ) #1 Fri Sep 11 14:36:53 CEST 2015
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Overkiz Kizbox mini
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] AT91: Detected soc type: at91sam9x5
[ 0.000000] AT91: Detected soc subtype: at91sam9g25
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=ubi0:root
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 125620K/131072K available (2698K kernel code, 133K rwdata, 988K rodata, 128K init, 194K bss, 5452K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc03a1f5c (3688 kB)
[ 0.000000] .init : 0xc03a2000 - 0xc03c2000 ( 128 kB)
[ 0.000000] .data : 0xc03c2000 - 0xc03e37c0 ( 134 kB)
[ 0.000000] .bss : 0xc03e37c0 - 0xc0414394 ( 195 kB)
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Main crystal frequency not set, using approximate value
[ 0.000000] parent_rate: 0
[ 0.000000] pmc: c7802400
[ 0.000000] rate: 0
[ 0.000000] min: 0
[ 0.000000] max: 133333333
[ 0.000000] rate: 148866833
[ 0.000000] min: 0
[ 0.000000] max: 133333333
[ 0.000000] master clk is overclocked
[ 0.000000] of_fixed_clk_setup
[ 0.000000] clock freq: 5000000
[ 0.000000] clock accuracy: 0
[ 0.000000] clock name: adc_op_clk
[ 0.000000] error !
[ 0.000000] Done
[ 0.000000] of_fixed_clk_setup
[ 0.000000] clock freq: 12000000
[ 0.000000] clock accuracy: 0
[ 0.000000] clock name: main_xtal
[ 0.000000] rate: 133333333
[ 0.000000] min: 0
[ 0.000000] max: 133333333
[ 0.000000] error !
[ 0.000000] Done
[ 0.000000] of_fixed_clk_setup
[ 0.000000] clock freq: 32768
[ 0.000000] clock accuracy: 0
[ 0.000000] clock name: slow_xtal
[ 0.000000] error !
[ 0.000000] Done
[ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns
[ 0.054687] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)
[ 0.054687] pid_max: default: 32768 minimum: 301
[ 0.062500] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.062500] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.062500] CPU: Testing write buffer coherency: ok
[ 0.062500] Setting up static identity map for 0x20290ed8 - 0x20290f54
[ 0.070312] devtmpfs: initialized
[ 0.070312] pinctrl core: initialized pinctrl subsystem
[ 0.093750] NET: Registered protocol family 16
[ 0.093750] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.117187] AT91: Power Management
[ 0.117187] gpio-at91 fffff400.gpio: at address fefff400
[ 0.117187] gpio-at91 fffff600.gpio: at address fefff600
[ 0.117187] gpio-at91 fffff800.gpio: at address fefff800
[ 0.117187] gpio-at91 fffffa00.gpio: at address fefffa00
[ 0.125000] pinctrl-at91 ahb:apb:pinctrl at fffff400: initialized AT91 pinctrl driver
[ 0.164062] at_hdmac ffffec00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
[ 0.164062] at_hdmac ffffee00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
[ 0.171875] usbcore: registered new interface driver usbfs
[ 0.171875] usbcore: registered new interface driver hub
[ 0.171875] usbcore: registered new device driver usb
[ 0.171875] Switched to clocksource tcb_clksrc
[ 0.187500] NET: Registered protocol family 2
[ 0.195312] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.195312] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.195312] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.195312] TCP: reno registered
[ 0.195312] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.195312] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.195312] NET: Registered protocol family 1
[ 0.195312] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.203125] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.203125] io scheduler noop registered (default)
[ 0.210937] f801c000.serial: ttyS1 at MMIO 0xf801c000 (irq = 30, base_baud = 8333333) is a ATMEL_SERIAL
[ 0.210937] fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 16, base_baud = 8333333) is a ATMEL_SERIAL
[ 0.562500] console [ttyS0] enabled
[ 0.578125] brd: module loaded
[ 0.601562] loop: module loaded
[ 0.617187] atmel_nand 40000000.nand: Use On Flash BBT
[ 0.625000] atmel_nand 40000000.nand: Using dma0chan0 for DMA transfers.
[ 0.632812] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.632812] nand: AMD/Spansion S34ML01G2
[ 0.640625] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.648437] atmel_nand 40000000.nand: minimum ECC: 4 bits in 512 bytes
[ 0.648437] atmel_nand 40000000.nand: Initialize PMECC params, cap: 4, sector: 512
[ 0.656250] Bad block table found at page 65472, version 0x01
[ 0.664062] Bad block table found at page 65408, version 0x01
[ 0.671875] 2 ofpart partitions found on MTD device atmel_nand
[ 0.679687] Creating 2 MTD partitions on "atmel_nand":
[ 0.679687] 0x000000000000-0x000000020000 : "bootstrap"
[ 0.687500] 0x000000020000-0x000080000000 : "ubi"
[ 0.695312] mtd: partition "ubi" extends beyond the end of device "atmel_nand" -- size truncated to 0x7fe0000
[ 0.710937] libphy: MACB_mii_bus: probed
[ 0.804687] macb f802c000.ethernet eth0: Cadence MACB rev 0x0001010c at 0xf802c000 irq 26 (f8:81:1a:02:4a:3b)
[ 0.812500] macb f802c000.ethernet eth0: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f802c000.etherne:01, irq=-1)
[ 0.820312] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.828125] ehci-atmel: EHCI Atmel driver
[ 0.828125] atmel-ehci 700000.ehci: EHCI Host Controller
[ 0.835937] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 0.843750] atmel-ehci 700000.ehci: irq 32, io mem 0x00700000
[ 0.867187] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 0.867187] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.875000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.882812] usb usb1: Product: EHCI Host Controller
[ 0.882812] usb usb1: Manufacturer: Linux 4.0.4 ehci_hcd
[ 0.890625] usb usb1: SerialNumber: 700000.ehci
[ 0.898437] hub 1-0:1.0: USB hub found
[ 0.898437] hub 1-0:1.0: 3 ports detected
[ 0.906250] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.914062] ohci-atmel: OHCI Atmel driver
[ 0.914062] AT91: Starting after general reset
[ 0.921875] at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=1)
[ 0.929687] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.937500] usbcore: registered new interface driver usbhid
[ 0.945312] usbhid: USB HID core driver
[ 0.945312] TCP: cubic registered
[ 0.953125] NET: Registered protocol family 17
[ 0.960937] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 0.976562] VFS: Cannot open root device "ubi0:root" or unknown-block(0,0): error -2
[ 0.984375] Please append a correct "root=" boot option; here are the available partitions:
[ 0.992187] 0100 8192 ram0 (driver?)
[ 0.992187] 0101 8192 ram1 (driver?)
[ 1.000000] 0102 8192 ram2 (driver?)
[ 1.007812] 0103 8192 ram3 (driver?)
[ 1.007812] 1f00 128 mtdblock0 (driver?)
[ 1.015625] 1f01 130944 mtdblock1 (driver?)
[ 1.015625] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.015625] CPU: 0 PID: 1 Comm: swapper Not tainted 4.0.4 #1
[ 1.015625] Hardware name: Atmel AT91SAM9
[ 1.015625] [<c000ded0>] (unwind_backtrace) from [<c000bd00>] (show_stack+0x10/0x14)
[ 1.015625] [<c000bd00>] (show_stack) from [<c028d8dc>] (panic+0x74/0x1dc)
[ 1.015625] [<c028d8dc>] (panic) from [<c03a310c>] (mount_block_root+0x26c/0x2b0)
[ 1.015625] [<c03a310c>] (mount_block_root) from [<c03a3338>] (prepare_namespace+0x88/0x1ac)
[ 1.015625] [<c03a3338>] (prepare_namespace) from [<c03a2d54>] (kernel_init_freeable+0x168/0x1ac)
[ 1.015625] [<c03a2d54>] (kernel_init_freeable) from [<c028ca90>] (kernel_init+0x8/0xe0)
[ 1.015625] [<c028ca90>] (kernel_init) from [<c0009658>] (ret_from_fork+0x14/0x3c)
[ 1.015625] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 64.492187] random: nonblocking pool is initialized
-------------- next part --------------
static unsigned long clk_main_recalc_rate(struct at91_pmc *pmc,
unsigned long parent_rate)
{
u32 tmp;
if (parent_rate)
return parent_rate;
pr_warn("Main crystal frequency not set, using approximate value\n");pr_err("parent_rate: %lu\n", parent_rate);pr_err("pmc: %p\n", pmc);
tmp = pmc_read(pmc, AT91_CKGR_MCFR);
if (!(tmp & AT91_PMC_MAINRDY))
return 0;
return ((tmp & AT91_PMC_MAINF) * SLOW_CLOCK_FREQ) / MAINF_DIV;
}-------------- next part --------------
static unsigned long clk_master_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
u8 pres;
u8 div;
unsigned long rate = parent_rate;
struct clk_master *master = to_clk_master(hw);
struct at91_pmc *pmc = master->pmc;
const struct clk_master_layout *layout = master->layout;
const struct clk_master_characteristics *characteristics =
master->characteristics;
u32 tmp;
pmc_lock(pmc);
tmp = pmc_read(pmc, AT91_PMC_MCKR) & layout->mask;
pmc_unlock(pmc);
pres = (tmp >> layout->pres_shift) & MASTER_PRES_MASK;
div = (tmp >> MASTER_DIV_SHIFT) & MASTER_DIV_MASK;
if (characteristics->have_div3_pres && pres == MASTER_PRES_MAX)
rate /= 3;
else
rate >>= pres;
rate /= characteristics->divisors[div];pr_err("rate: %lu\n", rate);pr_err("min: %lu\n", characteristics->output.min); pr_err("max: %lu\n", characteristics->output.max);
if (rate < characteristics->output.min)
pr_warn("master clk is underclocked");
else if (rate > characteristics->output.max)
pr_warn("master clk is overclocked");
return rate;
}
-------------- next part --------------
void of_fixed_clk_setup(struct device_node *node)
{
struct clk *clk;
const char *clk_name = node->name;
u32 rate;
u32 accuracy = 0;pr_err("of_fixed_clk_setup\n");
if (of_property_read_u32(node, "clock-frequency", &rate))
return;pr_err("clock freq: %u\n", rate);
of_property_read_u32(node, "clock-accuracy", &accuracy);
pr_err("clock accuracy: %u\n", accuracy);
of_property_read_string(node, "clock-output-names", &clk_name);
pr_err("clock name: %s\n", clk_name);
clk = clk_register_fixed_rate_with_accuracy(NULL, clk_name, NULL,
CLK_IS_ROOT, rate,
accuracy);
if (!IS_ERR(clk)){
pr_err("error !\n");
of_clk_add_provider(node, of_clk_src_simple_get, clk);
}pr_err("Done\n");
}
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150914/5ab722db/attachment-0001.sig>
Hi Antoine,
Quoted 34 lines · On Mon, 14 Sep 2015 14:41:32 +0200 Antoine Aubert <[email protected]> wrote:
Hi Boris,
Thank you for your help. I have some news thanks to traces in clk driver.
Le 08/09/2015 18:12, Boris Brezillon a ?crit :
Quoted 28 lines
Hi Antoine,
Quoted 8 lines · On Mon, 7 Sep 2015 09:31:07 +0200 Antoine Aubert <[email protected]> wrote:
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
Quoted 8 lines
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
According to your
clk_summarydump that's not the case.Quoted 3 lines
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day)
Quoted 8 lines
Quoted 1 line
I'd say no, but could you tell me more about your watchdog issues.
Yet, we did not take the analysis. We just observed these resets.
But, I found a clue:
We recently removed the slow clock to the PCB. I forgot to disabled theslow_xtal. :/
Can there be a link ? (I think so...)
Yep. The watchdog timer is based on the slow clock, which is taking its source from the crystal oscillator (requires a 32KHz external crystal), or the internal RC oscillator.
Since the internal RC oscillator is not as accurate as the one using an external crystal (+-5%), you might just reset the watchdog a bit too late.
Also, if you don't have this crystal, the clk event device is not reliable (unless you made a patch to change its source to one of the main clk divisor instead of the slow clk), but that should not impact the watchdog part.
Quoted 7 lines
Quoted 7 lines
Quoted 3 lines
Why is it that the frequency of Crystal is not found ?
That's a good question, and honestly I don't. Everything seems to be defined properly in your device tree.
Quoted 8 lines
Quoted 3 lines
Could you add some traces in the fixed-rate clk driver [1] to see if the
main_xtalis correctly registered and if its registration occurs before themain_oscregistration?On our board, there is two kernel boot phases.
First, we boot from at91-bootstrap.
Second we launched kexec with an other kernel.
Yes, I kinda know this workflow :-).
Quoted 7 lines
I found that the device tree is well loaded from the at91-bootstrap. Any crystal issues. But, on kexec --exec, (with the same kernel) those issues appears. (see dmesg attached)
If I launch kexec with --dtb, it's working ...
I thought kexec keep old dtb. Was I wrong ?
AFAIR, kexec is able to use the content of /proc/device-tree and create a dtb image to pass to the new kernel, but are you using the same kernel (4.0.4) for your "linux-based" bootloader?
If that's not the case, then you're not supposed to pass the same device tree (see this note [1]).
Best Regards,
Boris
[1]http://lxr.free-electrons.com/source/Documentation/arm/Atmel/README#L105
Signature · 3 lines
Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
Hi Antoine,
Quoted 3 lines · On Mon, 14 Sep 2015 14:41:32 +0200 Antoine Aubert <[email protected]> wrote:
Hi Boris,
Thank you for your help. I have some news thanks to traces in clk driver.
Any progress regarding this problem. I think Jiri (in Cc) has pretty much the same problem (see this thread [1]).
IIRC, activating NO_HZ_IDLE solved the problem for you, but have you find the root cause?
Best Regards,
Boris
[1]http://thread.gmane.org/gmane.linux.ports.arm.kernel/413356
Quoted 73 lines
Le 08/09/2015 18:12, Boris Brezillon a ?crit :
Quoted 22 lines
Hi Antoine,
Quoted 8 lines · On Mon, 7 Sep 2015 09:31:07 +0200 Antoine Aubert <[email protected]> wrote:
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
Quoted 8 lines
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
Quoted 7 lines
According to your
clk_summarydump that's not the case.Quoted 3 lines
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day)I'd say no, but could you tell me more about your watchdog issues.
Yet, we did not take the analysis. We just observed these resets.
But, I found a clue:
We recently removed the slow clock to the PCB. I forgot to disabled theslow_xtal. :/
Can there be a link ? (I think so...)Quoted 9 lines
Quoted 2 lines
Why is it that the frequency of Crystal is not found ?
That's a good question, and honestly I don't. Everything seems to be defined properly in your device tree.
Could you add some traces in the fixed-rate clk driver [1] to see if the
main_xtalis correctly registered and if its registration occurs before themain_oscregistration?On our board, there is two kernel boot phases.
First, we boot from at91-bootstrap.
Second we launched kexec with an other kernel.I found that the device tree is well loaded from the at91-bootstrap. Any crystal issues. But, on kexec --exec, (with the same kernel) those issues appears. (see dmesg attached)
If I launch kexec with --dtb, it's working ...
I thought kexec keep old dtb. Was I wrong ?Quoted 7 lines
Best Regards,
Boris
Best regards,
Antoine Aubert
a.aubert at overkiz.com
Signature · 3 lines
Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
Hi Boris
Le 06/10/2015 16:12, Boris Brezillon a ?crit :
Quoted 5 lines
Hi Antoine,
On Mon, 14 Sep 2015 14:41:32 +0200
Antoine Aubert <[email protected]> wrote:
Quoted 8 lines
Quoted 3 lines
Hi Boris,
Thank you for your help. I have some news thanks to traces in clk driver.
Any progress regarding this problem. I think Jiri (in Cc) has pretty much the same problem (see this thread [1]).
IIRC, activatingNO_HZ_IDLEsolved the problem for you, but have you find the root cause?
I'm not sure that the same issue. Here I don't have slow xtal.
What I found:
* DTB was not up to date (build with an other kernel version) Since we start from kexec, we added --dtb option
* slow_xtal wasn't disabled in our DTS
* defconfig was outdated
What i did first:
* updated the dts, disabled slow xtal
* Update DTB
* activating NO_HZ_IDLE
Quoted 1 line
20d updtime without WRST
Today what I did:
* use LTS last kernel: 4.1.6
* updated the dts, disabled slow xtal
* generate config from scratch using "make ARCH=arm at91_dt_defconfig" (without NO_HZ_IDLE=
12h uptime, at this time no WRST
Quoted 83 lines
Best Regards,
Boris
[1]http://thread.gmane.org/gmane.linux.ports.arm.kernel/413356
Quoted 73 lines
Le 08/09/2015 18:12, Boris Brezillon a ?crit :
Quoted 22 lines
Hi Antoine,
Quoted 8 lines · On Mon, 7 Sep 2015 09:31:07 +0200 Antoine Aubert <[email protected]> wrote:
Hi,
I currently bring up a board based on AT91SAM9G25cu, and I having problems of watchdogs resets.
We use linux-4.04 mainline, and i found some weird warnings on kernel traces, concerning main clk.
Quoted 8 lines
[ 0.000000] Main crystal frequency not set, using approximate value [ 0.000000] master clk is overclocked [ 0.000000] sched_clock: 32 bits at 128 Hz, resolution 7812500ns, wraps every 16777216000000000ns [ 0.007812] Calibrating delay loop... 198.76 BogoMIPS (lpj=775168)I set crystal clock in the DT, but it doesn't seems to work.. I feel that the board works out of the specified range.
Quoted 7 lines
According to your
clk_summarydump that's not the case.Quoted 3 lines
So here comes my questions:
Can there be a relationship with watchdog problems ? (1 per day)I'd say no, but could you tell me more about your watchdog issues.
Yet, we did not take the analysis. We just observed these resets.
But, I found a clue:
We recently removed the slow clock to the PCB. I forgot to disabled theslow_xtal. :/
Can there be a link ? (I think so...)Quoted 9 lines
Quoted 2 lines
Why is it that the frequency of Crystal is not found ?
That's a good question, and honestly I don't. Everything seems to be defined properly in your device tree.
Could you add some traces in the fixed-rate clk driver [1] to see if the
main_xtalis correctly registered and if its registration occurs before themain_oscregistration?On our board, there is two kernel boot phases.
First, we boot from at91-bootstrap.
Second we launched kexec with an other kernel.I found that the device tree is well loaded from the at91-bootstrap. Any crystal issues. But, on kexec --exec, (with the same kernel) those issues appears. (see dmesg attached)
If I launch kexec with --dtb, it's working ...
I thought kexec keep old dtb. Was I wrong ?Quoted 7 lines
Best Regards,
Boris
Best regards,
Antoine Aubert
a.aubert at overkiz.com
Antoine Aubert
a.aubert at overkiz.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151006/b7d54765/attachment.sig>
Hi Antoine,
Quoted 8 lines · Antoine Aubert
Le 06/10/2015 16:12, Boris Brezillon a ?crit :
Quoted 5 lines
Any progress regarding this problem. I think Jiri (in Cc) has pretty much the same problem (see this thread [1]).
IIRC, activatingNO_HZ_IDLEsolved the problem for you, but have you find the root cause?I'm not sure that the same issue. Here I don't have slow xtal.
There was no issue, it was just a misunderstanding on how the watchdog stack is working.
Quoted 13 lines
What I found:
* DTB was not up to date (build with an other kernel version) Since we start from kexec, we added --dtb option
*slow_xtalwasn't disabled in our DTS
* defconfig was outdatedWhat i did first:
* updated the dts, disabled slow xtal
* Update DTB
* activatingNO_HZ_IDLEQuoted 1 line
20d updtime without WRST
Quoted 7 lines
Today what I did:
* use LTS last kernel: 4.1.6
* updated the dts, disabled slow xtal
* generate config from scratch using "make ARCH=armat91_dt_defconfig" (without NO_HZ_IDLE=12h uptime, at this time no WRST
Great, no issue then, thank you !
Sylvain