phy: for 4.4 merge window

index 60c6f2a..0289d3b 100644
@@ -44,6 +44,9 @@ Required properties:
 	- the "ref" clock is used to get the rate of the clock provided to the
 	  PHY module
 
+Optional properties:
+- vbus-supply: power-supply phandle for vbus power source
+
 The first phandle argument in the PHY specifier identifies the PHY, its
 meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
 and Exynos 4212) it is as follows:

new file mode 100644
index 0000000..00100cf
@@ -0,0 +1,68 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy@11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port@11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port@11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};

index 47da573..ec436c1 100644
@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF

index a5b18c1..a7cc629 100644
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o

new file mode 100644
index 0000000..761c4bc
@@ -0,0 +1,47 @@
+Broadcom Cygnus PCIe PHY
+
+Required properties:
+- compatible: must be "brcm,cygnus-pcie-phy"
+- reg: base address and length of the PCIe PHY block
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Each PCIe PHY should be represented by a child node
+
+Required properties For the child node:
+- reg: the PHY ID
+0 - PCIe RC 0
+1 - PCIe RC 1
+- #phy-cells: must be 0
+
+Example:
+	pcie_phy: phy@0301d0a0 {
+		compatible = "brcm,cygnus-pcie-phy";
+		reg = <0x0301d0a0 0x14>;
+
+		pcie0_phy: phy@0 {
+			reg = <0>;
+			#phy-cells = <0>;
+		};
+
+		pcie1_phy: phy@1 {
+			reg = <1>;
+			#phy-cells = <0>;
+		};
+	};
+
+	/* users of the PCIe phy */
+
+	pcie0: pcie@18012000 {
+		...
+		...
+		phys = <&pcie0_phy>;
+		phy-names = "pcie-phy";
+	};
+
+	pcie1: pcie@18013000 {
+		...
+		...
+		phys = <pcie1_phy>;
+		phy-names = "pcie-phy";
+	};

index ec436c1..7eb5859d 100644
@@ -380,4 +380,13 @@ config PHY_BRCMSTB_SATA
 	  Enable this to support the SATA3 PHY on 28nm Broadcom STB SoCs.
 	  Likely useful only with CONFIG_SATA_BRCMSTB enabled.
 
+config PHY_CYGNUS_PCIE
+	tristate "Broadcom Cygnus PCIe PHY driver"
+	depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
+	select GENERIC_PHY
+	default ARCH_BCM_CYGNUS
+	help
+	  Enable this to support the Broadcom Cygnus PCIe PHY.
+	  If unsure, say N.
+
 endmenu

index a7cc629..075db1a 100644
@@ -47,3 +47,4 @@ obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
 obj-$(CONFIG_PHY_BRCMSTB_SATA)		+= phy-brcmstb-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
+obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o

index 7ba7ab7..be0055c 100644
@@ -1291,6 +1291,13 @@ F:	arch/arm/mach-mediatek/
 N:	mtk
 K:	mediatek
 
+ARM/Mediatek USB3 PHY DRIVER
+M:	Chunfeng Yun <[email protected]>
+L:	[email protected] (moderated for non-subscribers)
+L:	[email protected] (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/phy/phy-mt65xx-usb3.c
+
 ARM/MICREL KS8695 ARCHITECTURE
 M:	Greg Ungerer <[email protected]>
 L:	[email protected] (moderated for non-subscribers)