configs: add Freescale i.MX6 SoloX Sabre SD support
PATCH 1/1 configs: add Freescale i.MX6 SoloX Sabre SD support
From: Vincent Stehl? <[email protected]>
The i.MX6 SoloX SABRE board for smart devices is Freescale's reference design board based on the heterogeneous ARM Cortex-A9 + Cortex-M4 i.MX6 SoloX applications processor.
This defconfig is inspired from previous freescale_imx6*sabresd_defconfig, and is based on Freescale "official" git repo on git.freescale.com and SW release 3.10.53_1.1.0_ga.
---
Hi,
This is a proposed defconfig for i.MX6 SoloX.
Because the i.MX6 SoloX is not supported with the Freescale release 3.10.17 currently in use by i.MX6 defconfigs in buildroot, and because patches to "bump" other i.MX6 boards to release 3.10.53 have been kindly submitted by Gary [1], this defconfig is based on release 3.10.53 for consistency.
To compile properly, this defconfig depends on a "refresh" of an u-boot patch, posted earlier [2].
Best regards,
V.
[1] http://patchwork.ozlabs.org/patch/476413/ and more
[2] http://patchwork.ozlabs.org/patch/474897/
board/freescale/imx6sabre/readme.txt | 63 ++++++++++++++++++++++++------- configs/freescale_imx6sxsabresd_defconfig | 35 +++++++++++++++++ 2 files changed, 84 insertions(+), 14 deletions(-) create mode 100644 configs/freescale_imx6sxsabresd_defconfig
board/freescale/imx6sabre/readme.txt +49 -14
@@ -1,14 +1,19 @@ -******************************************************* -Freescale i.MX6Q and i.MX6DL SABRESD development boards -******************************************************* +******************************************************** +Freescale i.MX6 Q, DL and SoloX SABRE development boards +******************************************************** -This file documents the Buildroot support for the Freescale SABRE Board for -Smart Devices Based on the i.MX 6 Series (SABRESD), as well as the Freescale -SABRE Board for Automotive Infotainment. +This file documents the Buildroot support for the Freescale SABRE Board +for Smart Devices Based on the i.MX 6 and i.MX 6SoloX Series (SABRESD), +as well as the Freescale SABRE Board for Automotive Infotainment. -Read the SABRESD Quick Start Guide for an introduction to the board: +Read the i.MX 6 SABRESD Quick Start Guide for an introduction to the +board: http://cache.freescale.com/files/32bit/doc/quick_start_guide/SABRESDB_IMX6_QSG.pdf +Read the i.MX 6 SoloX SABRESD Quick Start Guide for an introduction to +the board: +http://cache.freescale.com/files/32bit/doc/user_guide/IMX6SOLOXQSG.pdf + Read the SABRE for Automotive Infotainment Quick Start Guide for an introduction to the board: http://cache.freescale.com/files/32bit/doc/user_guide/IMX6SABREINFOQSG.pdf
@@ -25,6 +30,10 @@ For i.MX6DL SABRE SD board: make freescale_imx6dlsabresd_defconfig +For i.MX6 SoloX SABRE SD board: + + make freescale_imx6sxsabresd_defconfig + For i.MX6Q SABRE Auto board: make freescale_imx6qsabreauto_defconfig
@@ -38,12 +47,12 @@ Build all components: make You will find in ./output/images/ the following files: - - imx6dl-sabresd.dtb or imx6q-sabresd.dtb or imx6q-sabreauto.dtb or - imx6dl-sabreauto.dtb + - imx6dl-sabresd.dtb or imx6q-sabresd.dtb or imx6sx-sdb.dtb or + imx6q-sabreauto.dtb or imx6dl-sabreauto.dtb - rootfs.ext2 - rootfs.tar - u-boot.imx - - uImage + - uImage, or zImage for i.MX6 SoloX Create a bootable SD card =========================
@@ -63,17 +72,43 @@ and copy the bootloader, kernel, DTBs and root filesystem as needed. Boot the SABRE board ==================== -SABRE SD --------- +i.MX6 SABRE SD +-------------- -To boot your newly created system on a SABRE SD Board (refer to the SABRE SD -Quick Start Guide for guidance): +To boot your newly created system on an i.MX6 SABRE SD Board (refer to +the i.MX6 SABRE SD Quick Start Guide for guidance): - insert the SD card in the SD3 slot of the board; - locate the BOOT dip switches (SW6), set dips 2 and 7 to ON, all others to OFF; - connect a Micro USB cable to Debug Port and connect using a terminal emulator at 115200 bps, 8n1; - power on the board. +i.MX6 SoloX SABRE SD +-------------------- + +To boot your newly created system on an i.MX6 SoloX SABRE SD Board +(refer to the i.MX6 SoloX SABRE SD Quick Start Guide for guidance): +- insert the SD card in the J4-SD4 socket at the bottom of the board; +- Set the SW10, SW11 and SW12 DIP switches at the top of the board in + their default position, to boot from SD card. Reference configuration: + + SW10 + 1 2 3 4 5 6 7 8 + off off off off off off off off + + SW11 + 1 2 3 4 5 6 7 8 + off off ON ON ON off off off + + SW12 + 1 2 3 4 5 6 7 8 + off ON off off off off off off + +- connect a Micro USB cable to the J16 Debug Port at the bottom of the + board. This is a dual UART debug port; connect to the first tty using + a terminal emulator at 115200 bps, 8n1; +- power on the board with the SW1-PWR switch at the top of the board. + SABRE Auto ----------
configs/freescale_imx6sxsabresd_defconfig new file +35 -0
@@ -0,0 +1,35 @@ +# architecture +BR2_arm=y +BR2_cortex_a9=y + +# patches +BR2_GLOBAL_PATCH_DIR="board/freescale/imx6sabre/patches" + +# toolchain +BR2_KERNEL_HEADERS_VERSION=y +BR2_DEFAULT_KERNEL_VERSION="3.10.53" +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_10=y + +# system +BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0" + +# kernel +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="git://git.freescale.com/imx/linux-2.6-imx.git" +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="rel_imx_3.10.53_1.1.0_ga" +BR2_LINUX_KERNEL_DEFCONFIG="imx_v7" +BR2_LINUX_KERNEL_ZIMAGE=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx6sx-sdb" + +# filesystem +BR2_TARGET_ROOTFS_EXT2=y + +# bootloader +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="mx6sxsabresd" +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="git://git.freescale.com/imx/uboot-imx.git" +BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="rel_imx_3.10.53_1.1.0_ga" +BR2_TARGET_UBOOT_FORMAT_IMX=y
Signature · 1 line
2.1.4
Thomas Petazzoni
AppliedPATCH 1/1 configs: add Freescale i.MX6 SoloX Sabre SD support
Dear Vincent Stehle,
Quoted 10 lines · Vincent Stehle
From: Vincent Stehl? <[email protected]>
The i.MX6 SoloX SABRE board for smart devices is Freescale's reference design board based on the heterogeneous ARM Cortex-A9 + Cortex-M4 i.MX6 SoloX applications processor.
This defconfig is inspired from previous freescale_imx6*sabresd_defconfig, and is based on Freescale "official" git repo on git.freescale.com and SW release 3.10.53_1.1.0_ga.
Quoted 6 lines
Signed-off-by Vincent Stehl? <[email protected]>Cc Gary Bisson <[email protected]>Cc J?r?me Pouiller <[email protected]>Cc Gilles Talis <[email protected]>Cc Luca Ceresoli <[email protected]>---
Applied, thanks.
Thomas
Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com