Input: pixcir_i2c_ts: add wake and enable gpios

This patch improves the pixcir_i2c_ts touchscreen controller which is used by the POV PROTAB2 tablet.

On POV PROTAB2 tablet the WAKE and ENABLE gpios are used, and the screen is rotated, so touchscreen-inverted-x and touchscreen-inverted-y are needed.

In this patch the WAKE and ENABLE gpios are implemented and furtermore the touchscreen-inverted-x/y and touchscreen-swapped-x-y devicetree options are implemented.

Signed-off-by Sander Vermin <[email protected]>

---
 .../bindings/input/touchscreen/pixcir_i2c_ts.txt   |  24 ++--
 drivers/input/touchscreen/pixcir_i2c_ts.c          | 125 +++++++++++++++++++--
 2 files changed, 135 insertions(+), 14 deletions(-)

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +0 -2

index 8eb240a..5f25e96 100644
@@ -1,15 +1,25 @@
 * Pixcir I2C touchscreen controllers
 
 Required properties:
-- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
-- reg: I2C address of the chip

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +0 -0

 Example:
 

drivers/input/touchscreen/pixcir_i2c_ts.c +118 -7

index 4b961ad..87f86b5 100644
@@ -38,6 +38,13 @@ struct pixcir_i2c_ts_data {
 	struct input_dev *input;
 	struct gpio_desc *gpio_attb;
 	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_enable;
+	struct gpio_desc *gpio_wake;
+	u32 max_x;
+	u32 max_y;
+	bool invert_x;
+	bool invert_y;
+	bool swap_x_y;
 	const struct pixcir_i2c_chip_data *chip;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;

@@ -146,12 +153,27 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 			slot = slots[i];
 		}
 
+		if (ts->invert_x)
+			touch->x = ts->max_x - touch->x;
+
+		if (ts->invert_y)
+			touch->y = ts->max_y - touch->y;
+
 		input_mt_slot(ts->input, slot);
 		input_mt_report_slot_state(ts->input,
 					   MT_TOOL_FINGER, true);
 
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
+		if (!ts->swap_x_y) {
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
+					touch->x);
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
+					touch->y);
+		} else {
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
+					touch->y);
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
+					touch->x);
+		}
 
 		dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
 			i, slot, touch->x, touch->y);

@@ -194,6 +216,7 @@ static irqreturn_t pixcir_ts_isr(int irq, void *dev_id)
 static void pixcir_reset(struct pixcir_i2c_ts_data *tsdata)
 {
 	if (!IS_ERR_OR_NULL(tsdata->gpio_reset)) {
+		/* toggle reset pin */
 		gpiod_set_value_cansleep(tsdata->gpio_reset, 1);
 		ndelay(100);	/* datasheet section 1.2.3 says 80ns min. */
 		gpiod_set_value_cansleep(tsdata->gpio_reset, 0);

@@ -208,6 +231,14 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 	struct device *dev = &ts->client->dev;
 	int ret;
 
+	if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
+		if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
+			/* set wake pin */
+			gpiod_set_value_cansleep(ts->gpio_wake, 1);
+			dev_info(dev, "SET POWER: Set wake pin HIGH\n");
+		}
+	}
+
 	ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
 	if (ret < 0) {
 		dev_err(dev, "%s: can't read reg 0x%x : %d\n",

@@ -228,6 +259,14 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 		return ret;
 	}
 
+	if (mode == PIXCIR_POWER_HALT) {
+		if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
+			/* set wake pin */
+			gpiod_set_value_cansleep(ts->gpio_wake, 0);
+			dev_info(dev, "SET POWER: Set wake pin LOW\n");
+		}
+	}
+
 	return 0;
 }
 

@@ -302,6 +341,14 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 	struct device *dev = &ts->client->dev;
 	int error;
 
+	if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(ts->gpio_enable, 1);
+		dev_info(dev, "START: Set enable pin HIGH\n");
+	}
+
+	msleep(100);
+
 	/* LEVEL_TOUCH interrupt with active low polarity */
 	error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
 	if (error) {

@@ -325,6 +372,7 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 
 static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 {
+	struct device *dev = &ts->client->dev;
 	int error;
 
 	/* Disable interrupt generation */

@@ -343,6 +391,12 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 	/* Wait till running ISR is complete */
 	synchronize_irq(ts->client->irq);
 
+	if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(ts->gpio_enable, 0);
+		dev_info(dev, "STOP: Set enable pin LOW\n");
+	}
+
 	return 0;
 }
 

@@ -425,6 +479,7 @@ static int pixcir_parse_dt(struct device *dev,
 			   struct pixcir_i2c_ts_data *tsdata)
 {
 	const struct of_device_id *match;
+	struct device_node *np = dev->of_node;
 
 	match = of_match_device(of_match_ptr(pixcir_of_match), dev);
 	if (!match)

@@ -433,7 +488,12 @@ static int pixcir_parse_dt(struct device *dev,
 	tsdata->chip = (const struct pixcir_i2c_chip_data *)match->data;
 	if (!tsdata->chip)
 		return -EINVAL;
-
+	
+	/* Optional device tree properties */
+	tsdata->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
+	tsdata->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
+	tsdata->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
+	
 	return 0;
 }
 #else

@@ -490,19 +550,37 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 	input->dev.parent = &client->dev;
 
 	if (pdata) {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0, pdata->x_max, 0, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0, pdata->y_max, 0, 0);
+		if (!tsdata->swap_x_y) {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     pdata->x_max, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     pdata->y_max, 0, 0);
+		} else {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     pdata->y_max, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     pdata->x_max, 0, 0);
+		}
 	} else {
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
 		touchscreen_parse_properties(input, true);
-		if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
-		    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
+		tsdata->max_x = input_abs_get_max(input, ABS_MT_POSITION_X);
+		tsdata->max_y = input_abs_get_max(input, ABS_MT_POSITION_Y);
+		if (!tsdata->max_x || !tsdata->max_y) {
 			dev_err(dev, "Touchscreen size is not specified\n");
 			return -EINVAL;
 		}
+		if (tsdata->swap_x_y) {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     tsdata->max_y, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     tsdata->max_x, 0, 0);
+		}		
 	}
 
+	
+
 	tsdata->max_fingers = tsdata->chip->max_fingers;
 	if (tsdata->max_fingers > PIXCIR_MAX_SLOTS) {
 		tsdata->max_fingers = PIXCIR_MAX_SLOTS;

@@ -534,6 +612,24 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	tsdata->gpio_wake = devm_gpiod_get(dev, "wake",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_wake)) {
+		error = PTR_ERR(tsdata->gpio_wake);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to request wake gpio: %d\n", error);
+		return error;
+	}
+
+	tsdata->gpio_enable = devm_gpiod_get(dev, "enable",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_enable)) {
+		error = PTR_ERR(tsdata->gpio_enable);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to request enable gpio: %d\n", error);
+		return error;
+	}
+
 	error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, tsdata);

@@ -542,6 +638,21 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+
+	if (!IS_ERR_OR_NULL(tsdata->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(tsdata->gpio_enable, 1);
+		dev_info(dev, "PROBE: Set enable pin HIGH\n");
+	}
+
+	if (!IS_ERR_OR_NULL(tsdata->gpio_wake)) {
+		/* set wake pin */
+		gpiod_set_value_cansleep(tsdata->gpio_wake, 1);
+		dev_info(dev, "PROBE: Set wake pin HIGH\n");
+	}
+
+	msleep(100);
+
 	pixcir_reset(tsdata);
 
 	/* Always be in IDLE mode to save power, device supports auto wake */

Signature · 7 lines

2.5.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Quoted 5 lines · Sander Vermin

This patch improves the pixcir_i2c_ts touchscreen controller which is used by the POV PROTAB2 tablet.

On POV PROTAB2 tablet the WAKE and ENABLE gpios are used, and the screen is rotated, so touchscreen-inverted-x and touchscreen-inverted-y are needed.

In this patch the WAKE and ENABLE gpios are implemented and furtermore the touchscreen-inverted-x/y and touchscreen-swapped-x-y devicetree options are implemented.

Need to fix the line wrapping.

Quoted 18 lines

Signed-off-by Sander Vermin <[email protected]>

---
 .../bindings/input/touchscreen/pixcir_i2c_ts.txt   |  24 ++--
 drivers/input/touchscreen/pixcir_i2c_ts.c          | 125 +++++++++++++++++++--
 2 files changed, 135 insertions(+), 14 deletions(-)

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +0 -2

index 8eb240a..5f25e96 100644
@@ -1,15 +1,25 @@
 * Pixcir I2C touchscreen controllers
 
 Required properties:
-- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
-- reg: I2C address of the chip

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt line 9

Quoted 10 lines

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +6 -4

-- interrupts: interrupt to which the chip is connected
-- attb-gpio: GPIO connected to the ATTB line of the chip
-- touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
-- touchscreen-size-y: vertical resolution of touchscreen (in pixels)
+- compatible		: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
+- reg			: I2C address of the chip
+- interrupts		: interrupt to which the chip is connected
+- attb-gpio		: GPIO connected to the ATTB line of the chip
+- touchscreen-size-x	: horizontal resolution of touchscreen (in pixels)
+- touchscreen-size-y	: vertical resolution of touchscreen (in pixels)

Please do reformatting in a separate patch.

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt line 22

Quoted 13 lines

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +11 -1

 Optional properties:
-- reset-gpio: GPIO connected to the RESET line of the chip
+- reset-gpio		: GPIO connected to the RESET line of the chip
+- enable-gpios		: GPIO connected to the ENABLE line of the chip
+- wake-gpios		: GPIO connected to the WAKE line of the chip
+- touchscreen-fuzz-x	: horizontal noise value of the absolute input
+			    device (in pixels)
+- touchscreen-fuzz-y	: vertical noise value of the absolute input
+			    device (in pixels)
+- touchscreen-inverted-x: X axis is inverted (boolean)
+- touchscreen-inverted-y: Y axis is inverted (boolean)
+- touchscreen-swapped-x-y	  : X and Y axis are swapped (boolean)
+			    Swapping is done after inverting the axis

Adding these touchscreen properties are not mentioned in the subject.

Quoted 218 lines

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +0 -0

 Example:
 

drivers/input/touchscreen/pixcir_i2c_ts.c +103 -7

index 4b961ad..87f86b5 100644
@@ -38,6 +38,13 @@ struct pixcir_i2c_ts_data {
 	struct input_dev *input;
 	struct gpio_desc *gpio_attb;
 	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_enable;
+	struct gpio_desc *gpio_wake;
+	u32 max_x;
+	u32 max_y;
+	bool invert_x;
+	bool invert_y;
+	bool swap_x_y;
 	const struct pixcir_i2c_chip_data *chip;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;

@@ -146,12 +153,27 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 			slot = slots[i];
 		}
 
+		if (ts->invert_x)
+			touch->x = ts->max_x - touch->x;
+
+		if (ts->invert_y)
+			touch->y = ts->max_y - touch->y;
+
 		input_mt_slot(ts->input, slot);
 		input_mt_report_slot_state(ts->input,
 					   MT_TOOL_FINGER, true);
 
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
+		if (!ts->swap_x_y) {
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
+					touch->x);
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
+					touch->y);
+		} else {
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
+					touch->y);
+			input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
+					touch->x);
+		}
 
 		dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
 			i, slot, touch->x, touch->y);

@@ -194,6 +216,7 @@ static irqreturn_t pixcir_ts_isr(int irq, void *dev_id)
 static void pixcir_reset(struct pixcir_i2c_ts_data *tsdata)
 {
 	if (!IS_ERR_OR_NULL(tsdata->gpio_reset)) {
+		/* toggle reset pin */
 		gpiod_set_value_cansleep(tsdata->gpio_reset, 1);
 		ndelay(100);	/* datasheet section 1.2.3 says 80ns min. */
 		gpiod_set_value_cansleep(tsdata->gpio_reset, 0);

@@ -208,6 +231,14 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 	struct device *dev = &ts->client->dev;
 	int ret;
 
+	if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
+		if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
+			/* set wake pin */
+			gpiod_set_value_cansleep(ts->gpio_wake, 1);
+			dev_info(dev, "SET POWER: Set wake pin HIGH\n");
+		}
+	}
+
 	ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
 	if (ret < 0) {
 		dev_err(dev, "%s: can't read reg 0x%x : %d\n",

@@ -228,6 +259,14 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 		return ret;
 	}
 
+	if (mode == PIXCIR_POWER_HALT) {
+		if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
+			/* set wake pin */
+			gpiod_set_value_cansleep(ts->gpio_wake, 0);
+			dev_info(dev, "SET POWER: Set wake pin LOW\n");
+		}
+	}
+
 	return 0;
 }
 

@@ -302,6 +341,14 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 	struct device *dev = &ts->client->dev;
 	int error;
 
+	if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(ts->gpio_enable, 1);
+		dev_info(dev, "START: Set enable pin HIGH\n");
+	}
+
+	msleep(100);
+
 	/* LEVEL_TOUCH interrupt with active low polarity */
 	error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
 	if (error) {

@@ -325,6 +372,7 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 
 static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 {
+	struct device *dev = &ts->client->dev;
 	int error;
 
 	/* Disable interrupt generation */

@@ -343,6 +391,12 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 	/* Wait till running ISR is complete */
 	synchronize_irq(ts->client->irq);
 
+	if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(ts->gpio_enable, 0);
+		dev_info(dev, "STOP: Set enable pin LOW\n");
+	}
+
 	return 0;
 }
 

@@ -425,6 +479,7 @@ static int pixcir_parse_dt(struct device *dev,
 			   struct pixcir_i2c_ts_data *tsdata)
 {
 	const struct of_device_id *match;
+	struct device_node *np = dev->of_node;
 
 	match = of_match_device(of_match_ptr(pixcir_of_match), dev);
 	if (!match)

@@ -433,7 +488,12 @@ static int pixcir_parse_dt(struct device *dev,
 	tsdata->chip = (const struct pixcir_i2c_chip_data *)match->data;
 	if (!tsdata->chip)
 		return -EINVAL;
-
+	
+	/* Optional device tree properties */
+	tsdata->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
+	tsdata->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
+	tsdata->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
+	
 	return 0;
 }
 #else

@@ -490,19 +550,37 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 	input->dev.parent = &client->dev;
 
 	if (pdata) {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0, pdata->x_max, 0, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0, pdata->y_max, 0, 0);
+		if (!tsdata->swap_x_y) {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     pdata->x_max, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     pdata->y_max, 0, 0);
+		} else {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     pdata->y_max, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     pdata->x_max, 0, 0);
+		}
 	} else {
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
 		touchscreen_parse_properties(input, true);
-		if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
-		    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
+		tsdata->max_x = input_abs_get_max(input, ABS_MT_POSITION_X);
+		tsdata->max_y = input_abs_get_max(input, ABS_MT_POSITION_Y);
+		if (!tsdata->max_x || !tsdata->max_y) {
 			dev_err(dev, "Touchscreen size is not specified\n");
 			return -EINVAL;
 		}
+		if (tsdata->swap_x_y) {
+			input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+					     tsdata->max_y, 0, 0);
+			input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+					     tsdata->max_x, 0, 0);
+		}		
 	}
 
+	
+
 	tsdata->max_fingers = tsdata->chip->max_fingers;
 	if (tsdata->max_fingers > PIXCIR_MAX_SLOTS) {
 		tsdata->max_fingers = PIXCIR_MAX_SLOTS;

@@ -534,6 +612,24 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	tsdata->gpio_wake = devm_gpiod_get(dev, "wake",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_wake)) {
+		error = PTR_ERR(tsdata->gpio_wake);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to request wake gpio: %d\n", error);
+		return error;
+	}
+
+	tsdata->gpio_enable = devm_gpiod_get(dev, "enable",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_enable)) {
+		error = PTR_ERR(tsdata->gpio_enable);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to request enable gpio: %d\n", error);
+		return error;
+	}
+
 	error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, tsdata);

@@ -542,6 +638,21 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 

drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_probe(struct i2c_client *client, · line 652

Quoted 12 lines

drivers/input/touchscreen/pixcir_i2c_ts.c +12 -0

+
+	if (!IS_ERR_OR_NULL(tsdata->gpio_enable)) {
+		/* set enable pin */
+		gpiod_set_value_cansleep(tsdata->gpio_enable, 1);
+		dev_info(dev, "PROBE: Set enable pin HIGH\n");
+	}
+
+	if (!IS_ERR_OR_NULL(tsdata->gpio_wake)) {
+		/* set wake pin */
+		gpiod_set_value_cansleep(tsdata->gpio_wake, 1);
+		dev_info(dev, "PROBE: Set wake pin HIGH\n");
+	}

Quoted 14 lines

drivers/input/touchscreen/pixcir_i2c_ts.c +3 -0

+
+	msleep(100);
+
 	pixcir_reset(tsdata);
 
 	/* Always be in IDLE mode to save power, device supports auto wake */

Signature · 7 lines

2.5.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel