arm64: Use contiguous PTE bit for the kernel linear mapping
v3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
Changes from V2:
This version removes the kernel command line parameter and replaces it with a config option. It also renames a couple of the macros. Patches rebased to 4.3rc4.
Changes from V1:
This version is similar to the previous versions with the addition of contpte/nocontpte kernel parameters for enabling/disabling the functionality. I defaulted it to contpte, but will change it to nocontpte if someone feels strongly about that. I considered making the default a kconfig option, but decided against it to avoid adding clutter for what should eventually be a fairly normal piece of functionality. I also used the early_param_on_off() macro, which is a small and concise piece of code, but varies a little from the more common parameter=value kernel parameters.
Also, continuing thanks to Steve Capper who has been religiously testing these patch sets, and found a bug in the previous implementation.
Finally, I removed the formatting change per Catalin.
Original Description:
When running 64k pages it became apparent that it was possible that the kernel could create more TLB pressure in certain circumstances when compared to the 4k page kernel. This is due to the fact that large portions of the 4k kernel can be mapped with 2M blocks. While the larger block size for 64k pages is 512M, it frequently won't be used for assorted reasons.
ARMv8 has a contiguous PTE bit that allows the TLBs to map a range larger than a single PTE if the range is physically contiguous. So its a good idea to use this where appropriate for the kernel mapping.
This patch adds the definitions for the contiguous bit, updates the kernel page range dump to understand them (and block translations), and updates the code in mmu.c to use the contiguous bit where appropriate for the kernel linear mapping.
Jeremy Linton (7):
arm64: Add contiguous page flag shifts and constants
arm64: PTE/PMD contiguous bit definition
arm64: Macros to check/set/unset the contiguous bit
arm64: Default kernel pages should be contiguous
arm64: Make the kernel page dump utility aware of the CONT bit
arm64: Add a kernel Kconfig option to enable contiguous PTE marking
arm64: Mark kernel page ranges contiguous
arch/arm64/Kconfig | 7 +++ arch/arm64/include/asm/page.h | 8 +++- arch/arm64/include/asm/pgtable-hwdef.h | 9 ++++ arch/arm64/include/asm/pgtable.h | 13 ++++++ arch/arm64/mm/dump.c | 18 +++++++- arch/arm64/mm/mmu.c | 81 ++++++++++++++++++++++++++++++---- 6 files changed, 125 insertions(+), 11 deletions(-)
Signature · 1 line
2.4.3
PATCH v3 1/7 arm64: Add contiguous page flag shifts and constants
Add the number of pages required to form a contiguous range, as well as some supporting constants.
--- arch/arm64/include/asm/page.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
arch/arm64/include/asm/page.h +7 -1
@@ -20,14 +20,20 @@#define __ASM_PAGE_H/* PAGE_SHIFT determines the page size */ +/* CONT_SHIFT determines the number of pages which can be tracked together */ #ifdef CONFIG_ARM64_64K_PAGES #define PAGE_SHIFT 16 +#define CONT_SHIFT 5#else #define PAGE_SHIFT 12 +#define CONT_SHIFT 4#endif -#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT) +#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)#define PAGE_MASK (~(PAGE_SIZE-1)) +#define CONT_SIZE (_AC(1, UL) << (CONT_SHIFT + PAGE_SHIFT)) +#define CONT_MASK (~(CONT_SIZE-1)) +/* * The idmap and swapper page tables need some space reserved in the kernel * image. Both require pgd, pud (4 levels only) and pmd tables to (section)
Signature · 1 line
2.4.3
PATCH v3 2/7 arm64: PTE/PMD contiguous bit definition
In reply to Jeremy LintonDefine the bit positions in the PTE and PMD for the contiguous bit.
--- arch/arm64/include/asm/pgtable-hwdef.h | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm64/include/asm/pgtable-hwdef.h +9 -0
@@ -55,6 +55,13 @@#define SECTION_MASK (~(SECTION_SIZE-1))/* +* Contiguous page definitions. +*/ +#define CONT_PTES (_AC(1, UL) << CONT_SHIFT) +/* the the numerical offset of the PTE within a range of CONT_PTES */ +#define CONT_RANGE_OFFSET (addr) (((addr)>>PAGE_SHIFT)&(CONT_PTES-1)) + +/* * Hardware page table definitions. * * Level 1 descriptor (PUD).
@@ -83,6 +90,7 @@#define PMD_SECT_S (_AT(pmdval_t, 3) << 8)#define PMD_SECT_AF (_AT(pmdval_t, 1) << 10)#define PMD_SECT_NG (_AT(pmdval_t, 1) << 11) +#define PMD_SECT_CONT (_AT(pmdval_t, 1) << 52)#define PMD_SECT_PXN (_AT(pmdval_t, 1) << 53)#define PMD_SECT_UXN (_AT(pmdval_t, 1) << 54)
@@ -105,6 +113,7 @@#define PTE_AF (_AT(pteval_t, 1) << 10)/* Access Flag */ #define PTE_NG (_AT(pteval_t, 1) << 11)/* nG */ #define PTE_DBM (_AT(pteval_t, 1) << 51)/* Dirty Bit Management */ +#define PTE_CONT (_AT(pteval_t, 1) << 52)/* Contiguous range */ #define PTE_PXN (_AT(pteval_t, 1) << 53)/* Privileged XN */ #define PTE_UXN (_AT(pteval_t, 1) << 54)/* User XN */
Signature · 1 line
2.4.3
PATCH v3 3/7 arm64: Macros to check/set/unset the contiguous bit
In reply to Jeremy LintonAdd the supporting macros to check if the contiguous bit is set, set the bit, or clear it in a PTE entry.
--- arch/arm64/include/asm/pgtable.h | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm64/include/asm/pgtable.h +11 -0
@@ -140,6 +140,7 @@ extern struct page *empty_zero_page;#define pte_special (pte) (!!(pte_val(pte) & PTE_SPECIAL))#define pte_write (pte) (!!(pte_val(pte) & PTE_WRITE))#define pte_exec (pte) (!(pte_val(pte) & PTE_UXN)) +#define pte_cont (pte) (!!(pte_val(pte) & PTE_CONT))#ifdef CONFIG_ARM64_HW_AFDBM #define pte_hw_dirty (pte) (pte_write(pte) && !(pte_val(pte) & PTE_RDONLY))
@@ -202,6 +203,16 @@ static inline pte_t pte_mkspecial(pte_t pte)return set_pte_bit (pte,__pgprot (PTE_SPECIAL )); } +static inline pte_t pte_mkcont (pte_t pte) +{ +return set_pte_bit (pte,__pgprot (PTE_CONT )); +} + +static inline pte_t pte_mknoncont (pte_t pte) +{ +return clear_pte_bit (pte,__pgprot (PTE_CONT )); +} +static inline void set_pte (pte_t *ptep,pte_t pte) { *ptep = pte;
Signature · 1 line
2.4.3
PATCH v3 4/7 arm64: Default kernel pages should be contiguous
In reply to Jeremy LintonThe default page attributes for a PMD being broken should have the CONT bit set. Create a new definition for an early boot range of PTE's that are contiguous.
--- arch/arm64/include/asm/pgtable.h | 2 ++ 1 file changed, 2 insertions(+)
arch/arm64/include/asm/pgtable.h +2 -0
@@ -72,6 +72,8 @@ extern void __pgd_error(const char *file, int line, unsigned long val);#define PAGE_KERNEL __pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE)#define PAGE_KERNEL_EXEC __pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE) +#define PAGE_KERNEL_EXEC_CONT __pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | \ + PTE_WRITE | PTE_CONT)#define PAGE_HYP __pgprot(_PAGE_DEFAULT | PTE_HYP)#define PAGE_HYP_DEVICE __pgprot(PROT_DEVICE_nGnRE | PTE_HYP)
Signature · 1 line
2.4.3
PATCH v3 5/7 arm64: Make the kernel page dump utility aware of the CONT bit
In reply to Jeremy LintonThe kernel page dump utility needs to be aware of the CONT bit before it will break up pages ranges for display.
--- arch/arm64/mm/dump.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
arch/arm64/mm/dump.c +17 -1
@@ -67,6 +67,12 @@ static struct addr_marker address_markers[] = { { -1, NULL }, }; +/* + * The page dumper groups page table entries of the same type into a single + * description. It uses pg_state to track the range information while + * iterating over the pte entries. When the continuity is broken it then + * dumps out a description of the range. + */ struct pg_state { struct seq_file *seq; const struct addr_marker *marker;
@@ -114,6 +120,16 @@ static const struct prot_bits pte_bits[] = { .set = "NG", .clear = " ", }, { + .mask = PTE_CONT, + .val = PTE_CONT, + .set = "CON", + .clear = " ", + }, { + .mask = PTE_TABLE_BIT, + .val = PTE_TABLE_BIT, + .set = " ", + .clear = "BLK", + }, { .mask = PTE_UXN, .val = PTE_UXN, .set = "UXN",
@@ -198,7 +214,7 @@ static void note_page(struct pg_state *st, unsigned long addr, unsigned level,unsigned long delta;if (st->current_prot) { -seq_printf (st->seq,"0x%16lx-0x%16lx " , +seq_printf (st->seq,"0x%016lx-0x%016lx " , st->start_address, addr); delta = (addr - st->start_address) >>10 ;
Signature · 1 line
2.4.3
PATCH v3 6/7 arm64: Add a kernel Kconfig option to enable contiguous PTE marking
In reply to Jeremy LintonAdd ARM64_CONT_PTE, so that the contiguous PTE marking in the kernel's linear mapping may be turned off. In general this should not be necessary, but it can help sanity check that the code/hardware is working properly.
--- arch/arm64/Kconfig | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm64/Kconfig +7 -0
@@ -400,6 +400,13 @@ config ARM64_VA_BITS default 42 if ARM64_VA_BITS_42 default 48 if ARM64_VA_BITS_48 +config ARM64_CONT_PTE + bool "Use contiguous page hint for kernel linear mapping" + default y + help + Marking kernel pages contiguous can reduce TLB pressure for + certain workloads. If unsure, say Y. + config CPU_BIG_ENDIAN bool "Build big-endian kernel" help
Signature · 1 line
2.4.3
PATCH v3 7/7 arm64: Mark kernel page ranges contiguous
In reply to Jeremy LintonWith 64k pages, the next larger segment size is 512M. The linux kernel also uses different protection flags to cover its code and data. Because of this requirement, the vast majority of the kernel code and data structures end up being mapped with 64k pages instead of the larger pages common with a 4k page kernel.
Recent ARM processors support a contiguous bit in the page tables which allows the a TLB to cover a range larger than a single PTE if that range is mapped into physically contiguous ram.
So, for the kernel its a good idea to set this flag. Some basic micro benchmarks show it can significantly reduce the number of L1 dTLB refills.
Add boot option to enable/disable CONT marking, as well as fix a bug found by Steve Capper.
--- arch/arm64/mm/mmu.c | 81 +++++++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 72 insertions(+), 9 deletions(-)
arch/arm64/mm/mmu.c +72 -9
@@ -69,6 +69,10 @@ static void __init *early_alloc(unsigned long sz)return ptr; } +#ifndef CONFIG_ARM64_CONT_PTE +#define CONFIG_ARM64_CONT_PTE 0 +#endif +/* * remap a PMD into pages */
@@ -80,19 +84,58 @@ static void split_pmd(pmd_t *pmd, pte_t *pte)do {/* * Need to have the least restrictive permissions available -* permissions will be fixed up later +* permissions will be fixed up later. Default the new page +* range as contiguous ptes. */ -set_pte (pte,pfn_pte (pfn,PAGE_KERNEL_EXEC )); +if (CONFIG_ARM64_CONT_PTE ) +set_pte (pte,pfn_pte (pfn,PAGE_KERNEL_EXEC_CONT )); +else +set_pte (pte,pfn_pte (pfn,PAGE_KERNEL_EXEC )); pfn++; }while (pte++, i++, i <PTRS_PER_PTE ); } +/* +* Given a PTE with the CONT bit set, determine where the CONT range +* starts, and clear the entire range of PTE CONT bits. +*/ +static void clear_cont_pte_range (pte_t *pte,unsigned long addr) +{ +int i; + + pte -=CONT_RANGE_OFFSET (addr); +for (i =0 ; i <CONT_PTES ; i++) { +set_pte (pte,pte_mknoncont (*pte)); + pte++; + } +flush_tlb_all (); +} + +/* +* Given a range of PTEs set the pfn and provided page protection flags +*/ +static void __populate_init_pte (pte_t *pte,unsigned long addr, +unsigned long end,phys_addr_t phys, +pgprot_t prot) +{ +unsigned long pfn =__phys_to_pfn (phys); + +do { +/* clear all the bits except the pfn, then apply the prot */ +set_pte (pte,pfn_pte (pfn, prot)); + pte++; + pfn++; + addr +=PAGE_SIZE ; + }while (addr != end); +} +static void alloc_init_pte (pmd_t *pmd,unsigned long addr, -unsigned long end,unsigned long pfn, +unsigned long end,phys_addr_t phys,pgprot_t prot,void *(*alloc)(unsigned long size)) {pte_t *pte; +unsigned long next;if (pmd_none (*pmd) ||pmd_sect (*pmd)) { pte =alloc (PTRS_PER_PTE *sizeof (pte_t));
@@ -104,10 +147,31 @@ static void alloc_init_pte(pmd_t *pmd, unsigned long addr,BUG_ON (pmd_bad (*pmd)); pte =pte_offset_kernel (pmd, addr); -do { -set_pte (pte,pfn_pte (pfn, prot)); - pfn++; - }while (pte++, addr +=PAGE_SIZE , addr != end); +if (!CONFIG_ARM64_CONT_PTE ) +__populate_init_pte (pte, addr, end, phys, prot); +else +do { + next =min (end, (addr +CONT_SIZE ) &CONT_MASK ); +if (((addr | next | phys) & ~CONT_MASK ) ==0 ) { +/* a block of CONT_PTES */ +__populate_init_pte (pte, addr, next, phys, + prot |__pgprot (PTE_CONT )); + }else { +/* +* If the range being split is already inside of a +* contiguous range but this PTE isn't going to be +* contiguous, then we want to unmark the adjacent +* ranges, then update the portion of the range we +* are interrested in. +*/ +clear_cont_pte_range (pte, addr); +__populate_init_pte (pte, addr, next, phys, prot); + } + + pte += (next - addr) >>PAGE_SHIFT ; + phys += next - addr; + addr = next; + }while (addr != end); }void split_pud (pud_t *old_pud,pmd_t *pmd)
@@ -168,8 +232,7 @@ static void alloc_init_pmd(struct mm_struct *mm, pud_t *pud, } } }else { -alloc_init_pte (pmd, addr, next,__phys_to_pfn (phys), - prot, alloc); +alloc_init_pte (pmd, addr, next, phys, prot, alloc); } phys += next - addr; }while (pmd++, addr = next, addr != end);
Signature · 1 line
2.4.3
Catalin Marinas
maintainerv3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
In reply to Jeremy LintonQuoted 8 lines · Jeremy Linton
Jeremy Linton (7):
arm64: Add contiguous page flag shifts and constants
arm64: PTE/PMD contiguous bit definition
arm64: Macros to check/set/unset the contiguous bit
arm64: Default kernel pages should be contiguous
arm64: Make the kernel page dump utility aware of the CONT bit
arm64: Add a kernelKconfigoption to enable contiguous PTE marking
arm64: Mark kernel page ranges contiguous
I queued the series without patch 6 (and a modification of patch 7 to get rid of the config option check). If we need this option, we can add it later but for (hardware) debugging purposes it looks to me like we can simply set PTE_CONT to 0.
Thanks.
Signature · 1 line
Catalin
v3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
Quoted 4 lines · Catalin Marinas
I queued the series without patch 6 (and a modification of patch 7 to get rid of the config option check). If we need this option, we can add it later but for (hardware) debugging purposes it looks to me like we can simply set
PTE_CONTto 0.
Sounds good to me.
Thanks,
v3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
Hello,
Just a heads up, but this patch is causing a boot problem on a m400. I
should know more soon.
Thanks,
v3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
Quoted 1 line · Jeremy Linton
Hello,
Hi Jeremy,
Quoted 2 lines
Just a heads up, but this patch is causing a boot problem on a m400. I
should know more soon.
Any chance you could share a reproducer/panic log/debug info, please? If we can't fix this soon, then we'll have to look at reverting the change, so getting a few more eyes on the problem might help.
Will
v3 cover arm64: Use contiguous PTE bit for the kernel linear mapping
Quoted 11 lines · Will Deacon
Quoted 1 line · Jeremy Linton
Hello,
Hi Jeremy,
Quoted 2 lines
Just a heads up, but this patch is causing a boot problem on a m400. I
should know more soon.Any chance you could share a reproducer/panic log/debug info, please? If we can't fix this soon, then we'll have to look at reverting the change, so getting a few more eyes on the problem might help.
Its usually just hangs although, once in a while it will generate an
unknown exception. I posted a patch last night which fixes it with a big hammer (extra tlb flush), but It doesn't appear to have made the mailing list (I regularly get relay rejected messages). I will attempt to re-post it again.