phy: add phy-hi6220-usb
Subsystems (2)
PATCH 1/1 phy: add phy-hi6220-usb
Support hi6220 use phy for HiKey board
Signed-off-by Zhangfei Gao <[email protected]>
--- .../devicetree/bindings/phy/phy-hi6220-usb.txt | 16 ++ drivers/phy/Kconfig | 9 ++ drivers/phy/Makefile | 1 + drivers/phy/phy-hi6220-usb.c | 168 +++++++++++++++++++++ 4 files changed, 194 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt create mode 100644 drivers/phy/phy-hi6220-usb.c
Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file +16 -0
@@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + };
drivers/phy/Kconfig +9 -0
@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA help Support for SATA PHY on Hisilicon hix5hd2 Soc. +config PHY_HI6220_USB + tristate "hi6220 USB PHY support" + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the HISILICON HI6220 USB PHY. + + To compile this driver as a module, choose M here. + config PHY_SUN4I_USB tristate "Allwinner sunxi SoC USB PHY driver" depends on ARCH_SUNXI && HAS_IOMEM && OF
drivers/phy/Makefile +1 -0
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o +obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.o
drivers/phy/phy-hi6220-usb.c new file +168 -0
168 lines not on this page · raw message
Signature · 1 line
1.9.1
Rob Herring
maintainerPATCH 1/1 phy: add phy-hi6220-usb
Quoted 5 lines · Zhangfei Gao
Support hi6220 use phy for HiKey board
Signed-off-by Zhangfei Gao <[email protected]>--- .../devicetree/bindings/phy/phy-hi6220-usb.txt | 16 ++
For the binding:
Acked-by Rob Herring <[email protected]>
Quoted 242 lines
drivers/phy/Kconfig | 9 ++ drivers/phy/Makefile | 1 + drivers/phy/phy-hi6220-usb.c | 168 +++++++++++++++++++++ 4 files changed, 194 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt create mode 100644 drivers/phy/phy-hi6220-usb.cDocumentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file +16
-0@@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + };drivers/phy/Kconfig +9
-0@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA help Support for SATA PHY on Hisilicon hix5hd2 Soc. +config PHY_HI6220_USB + tristate "hi6220 USB PHY support" + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the HISILICON HI6220 USB PHY. + + To compile this driver as a module, choose M here. + config PHY_SUN4I_USB tristate "Allwinner sunxi SoC USB PHY driver" depends on ARCH_SUNXI && HAS_IOMEM && OFdrivers/phy/Makefile +1
-0@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o +obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.odrivers/phy/phy-hi6220-usb.c new file +168
-0@@ -0,0 +1,168 @@ +/* +* Copyright (c) 2015 Linaro Ltd. +* Copyright (c) 2015 Hisilicon Limited. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +*/ + +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> + +#define SC_PERIPH_CTRL4 0x00c + +#define CTRL4_PICO_SIDDQ BIT(6) +#define CTRL4_PICO_OGDISABLE BIT(8) +#define CTRL4_PICO_VBUSVLDEXT BIT(10) +#define CTRL4_PICO_VBUSVLDEXTSEL BIT(11) +#define CTRL4_OTG_PHY_SEL BIT(21) + +#define SC_PERIPH_CTRL5 0x010 + +#define CTRL5_USBOTG_RES_SEL BIT(3) +#define CTRL5_PICOPHY_ACAENB BIT(4) +#define CTRL5_PICOPHY_BC_MODE BIT(5) +#define CTRL5_PICOPHY_CHRGSEL BIT(6) +#define CTRL5_PICOPHY_VDATSRCEND BIT(7) +#define CTRL5_PICOPHY_VDATDETENB BIT(8) +#define CTRL5_PICOPHY_DCDENB BIT(9) +#define CTRL5_PICOPHY_IDDIG BIT(10) + +#define SC_PERIPH_CTRL8 0x018 +#define SC_PERIPH_RSTEN0 0x300 +#define SC_PERIPH_RSTDIS0 0x304 + +#define RST0_USBOTG_BUS BIT(4) +#define RST0_POR_PICOPHY BIT(5) +#define RST0_USBOTG BIT(6) +#define RST0_USBOTG_32K BIT(7) + +#define EYE_PATTERN_PARA 0x7053348c + +struct hi6220_priv { +struct regmap *reg; +struct device *dev; +}; + +static void hi6220_phy_init (struct hi6220_priv *priv) +{ +struct regmap *reg = priv->reg; +u32 val, mask; + + val =RST0_USBOTG_BUS |RST0_POR_PICOPHY | +RST0_USBOTG |RST0_USBOTG_32K ; + mask = val; +regmap_update_bits (reg,SC_PERIPH_RSTEN0 , mask, val); +regmap_update_bits (reg,SC_PERIPH_RSTDIS0 , mask, val); +} + +static int hi6220_phy_setup (struct hi6220_priv *priv,bool on) +{ +struct regmap *reg = priv->reg; +u32 val, mask; +int ret; + +if (on) { + val =CTRL5_USBOTG_RES_SEL |CTRL5_PICOPHY_ACAENB ; + mask = val |CTRL5_PICOPHY_BC_MODE ; + ret =regmap_update_bits (reg,SC_PERIPH_CTRL5 , mask, val); +if (ret) + goto out; + + val =CTRL4_PICO_VBUSVLDEXT |CTRL4_PICO_VBUSVLDEXTSEL | +CTRL4_OTG_PHY_SEL ; + mask = val |CTRL4_PICO_SIDDQ |CTRL4_PICO_OGDISABLE ; + ret =regmap_update_bits (reg,SC_PERIPH_CTRL4 , mask, val); +if (ret) + goto out; + + ret =regmap_write (reg,SC_PERIPH_CTRL8 ,EYE_PATTERN_PARA ); +if (ret) + goto out; + }else { + val =CTRL4_PICO_SIDDQ ; + mask = val; + ret =regmap_update_bits (reg,SC_PERIPH_CTRL4 , mask, val); +if (ret) + goto out; + } + +return 0 ; +out: +dev_err (priv->dev,"failed to setup phy ret: %d\n" , ret); +return ret; +} + +static int hi6220_phy_start (struct phy *phy) +{ +struct hi6220_priv *priv =phy_get_drvdata (phy); + +return hi6220_phy_setup (priv, true); +} + +static int hi6220_phy_exit (struct phy *phy) +{ +struct hi6220_priv *priv =phy_get_drvdata (phy); + +return hi6220_phy_setup (priv, false); +} + +static struct phy_ops hi6220_phy_ops = { + .init = hi6220_phy_start, + .exit = hi6220_phy_exit, + .owner =THIS_MODULE , +}; + +static int hi6220_phy_probe (struct platform_device *pdev) +{ +struct phy_provider *phy_provider; +struct device *dev = &pdev->dev; +struct phy *phy; +struct hi6220_priv *priv; + + priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) +return -ENOMEM ; + + priv->dev = dev; + priv->reg =syscon_regmap_lookup_by_phandle (dev->of_node, +"hisilicon,peripheral-syscon" ); +if (IS_ERR (priv->reg)) { +dev_err (dev,"no hisilicon,peripheral-syscon\n" ); +return PTR_ERR (priv->reg); + } + +hi6220_phy_init (priv); + + phy =devm_phy_create (dev,NULL , &hi6220_phy_ops); +if (IS_ERR (phy)) +return PTR_ERR (phy); + +phy_set_drvdata (phy, priv); + phy_provider =devm_of_phy_provider_register (dev, of_phy_simple_xlate); +return PTR_ERR_OR_ZERO (phy_provider); +} + +static const struct of_device_id hi6220_phy_of_match[] = { + {.compatible ="hisilicon,hi6220-usb-phy" ,}, + { }, +}; +MODULE_DEVICE_TABLE (of, hi6220_phy_of_match); + +static struct platform_driver hi6220_phy_driver = { + .probe = hi6220_phy_probe, + .driver = { + .name ="hi6220-usb-phy" , + .of_match_table = hi6220_phy_of_match, + } +}; +module_platform_driver (hi6220_phy_driver); + +MODULE_DESCRIPTION ("HISILICON HI6220 USB PHY driver" ); +MODULE_ALIAS ("platform:hi6220-usb-phy" ); +MODULE_LICENSE ("GPL" );Signature · 6 lines
1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo at vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH v2 1/1 phy: add phy-hi6220-usb
In reply to Zhangfei GaoSupport hi6220 use phy for HiKey board
Acked-by Rob Herring <[email protected]>
Signed-off-by Zhangfei Gao <[email protected]>
---
Rebase to Linux 4.4-rc1
.../devicetree/bindings/phy/phy-hi6220-usb.txt | 16 ++ drivers/phy/Kconfig | 9 ++ drivers/phy/Makefile | 1 + drivers/phy/phy-hi6220-usb.c | 168 +++++++++++++++++++++ 4 files changed, 194 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt create mode 100644 drivers/phy/phy-hi6220-usb.c
Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file +16 -0
@@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + };
drivers/phy/Kconfig +9 -0
@@ -215,6 +215,15 @@ config PHY_MT65XX_USB3 for mt65xx SoCs. it supports two usb2.0 ports and one usb3.0 port. +config PHY_HI6220_USB + tristate "hi6220 USB PHY support" + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the HISILICON HI6220 USB PHY. + + To compile this driver as a module, choose M here. + config PHY_SUN4I_USB tristate "Allwinner sunxi SoC USB PHY driver" depends on ARCH_SUNXI && HAS_IOMEM && OF
drivers/phy/Makefile +1 -0
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o +obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
drivers/phy/phy-hi6220-usb.c new file +168 -0
168 lines not on this page · raw message
Signature · 1 line
1.9.1