Skip to contentSkip to conversation

ARM: dts: imx: ventana: add PWM nodes for Ventana boards

PATCH New Tim Harvey 2 participants 3 messages Nov 19, 2015 – Nov 25, 2015

Subsystems (2)
Device tree bindings Arm i.MX and Layerscape
lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH 1/2 ARM: dts: imx: ventana: add PWM nodes for Ventana boards

Ventana boards have an off-board connector with signals that can be pinmuxed as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled state which the bootloader can decide to enable based on bootloader config.

Signed-off-by Tim Harvey <[email protected]>
---
 arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 36 +++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 24 +++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 24 +++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 36 +++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 24 +++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 24 +++++++++++++++++++++++
 6 files changed, 168 insertions(+)
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi +36 -0
index 7b31fdb..fb0abd6 100644
@@ -174,6 +174,24 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;

@@ -294,6 +312,24 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm4: pwm4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi +24 -0
index 9709728..e4a1e72 100644
@@ -282,6 +282,18 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;

@@ -436,6 +448,18 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +24 -0
index dc1cd13..c37f89d 100644
@@ -287,6 +287,18 @@
 	};
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;

@@ -442,6 +454,18 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +36 -0
index d8aa22e..2b3c877 100644
@@ -378,6 +378,24 @@
 	};
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */
+	status = "disabled";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;

@@ -537,6 +555,24 @@
 			>;
 		};
 
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_pwm4: pwm4grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
arch/arm/boot/dts/imx6qdl-gw551x.dtsi +24 -0
index 741f3d5..118bea5 100644
@@ -198,6 +198,18 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &ssi1 {
 	status = "okay";
 };

@@ -290,6 +302,18 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart2: uart2grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
arch/arm/boot/dts/imx6qdl-gw552x.dtsi +24 -0
index d1e5048..cca39f1 100644
@@ -164,6 +164,18 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;

@@ -242,6 +254,18 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+			>;
+		};
+
 		pinctrl_uart2: uart2grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
Signature · 1 line
1.9.1
Applied
#1 lore raw

PATCH 1/2 ARM: dts: imx: ventana: add PWM nodes for Ventana boards

Quoted 5 lines · Tim Harvey

Ventana boards have an off-board connector with signals that can be pinmuxed as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled state which the bootloader can decide to enable based on bootloader config.

Signed-off-by Tim Harvey <[email protected]>

Applied both, thanks.

#2 lore raw

PATCH 1/2 ARM: dts: imx: ventana: add PWM nodes for Ventana boards

In reply to Tim Harvey
Quoted 5 lines · Tim Harvey

Ventana boards have an off-board connector with signals that can be pinmuxed as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled state which the bootloader can decide to enable based on bootloader config.

Signed-off-by Tim Harvey <[email protected]>

Tim,

Please use my kernel.org rather than linaro.org mail address in the future. The MAINTAINERS file had been updated for a few release cycles.

Shawn