Skip to contentSkip to conversation

brcmfmac: IBSS fix and cleanup

PATCH In review Arend van Spriel 2 participants 21 messages Dec 10, 2015 – Dec 11, 2015 Broadcom BRCM80211 IEEE802.11 wireless drivers

lore
Share & tools
lore
#0 lore raw

v2 cover brcmfmac: IBSS fix and cleanup

This series provides following:
* fix IBSS which got broken over time.
* new USB id for bcm43242 dongle.
* arp offload configuration through inet notifier.

The series is intended for 4.5 kernel and applies to master branch of the wireless-drivers-next repository.

Arend van Spriel (2):
brcmfmac: no interface combination check for single interface
brcmfmac: add 43242 device id for LG dongle

Franky Lin (1):
brcmfmac: add arp offload ip address table configuration support

Hante Meuleman (9):
brcmfmac: Simplify scan timing configuration.
brcmfmac: Use local storage for ssid iovar.
brcmfmac: Remove some redundant cfg80211 data.
brcmfmac: Cleanup pmksa cache handling code.
brcmfmac: Make TDLS a detectable feature.
brcmfmac: Add support for PCIE 4350 revision 5 device.
brcmfmac: Fix IBSS setup.
brcmfmac: Change error print in debug print.
brcmfmac: Move scheduled scan related interface layer structs.

Kosuke Tatsukawa (1):
brcmfmac: fix waitqueue_active without memory barrier in brcmfmac
driver

 .../broadcom/brcm80211/brcmfmac/cfg80211.c         | 233 ++++++++++-----------
 .../broadcom/brcm80211/brcmfmac/cfg80211.h         | 111 +---------
 .../wireless/broadcom/brcm80211/brcmfmac/core.c    | 108 ++++++++++
 .../wireless/broadcom/brcm80211/brcmfmac/core.h    |   2 +
 .../wireless/broadcom/brcm80211/brcmfmac/feature.c |   1 +
 .../wireless/broadcom/brcm80211/brcmfmac/feature.h |   4 +-
 .../broadcom/brcm80211/brcmfmac/fwil_types.h       | 105 ++++++++++
 .../wireless/broadcom/brcm80211/brcmfmac/msgbuf.c  |   3 +-
 .../wireless/broadcom/brcm80211/brcmfmac/pcie.c    |   8 +-
 .../wireless/broadcom/brcm80211/brcmfmac/sdio.c    |   6 +-
 .../net/wireless/broadcom/brcm80211/brcmfmac/usb.c |   4 +-
 .../broadcom/brcm80211/include/brcm_hw_ids.h       |   2 +
 .../broadcom/brcm80211/include/brcmu_wifi.h        |  23 --
 13 files changed, 342 insertions(+), 268 deletions(-)
Signature · 1 line
1.9.1
#1 lore raw

PATCH v2 1/13 brcmfmac: Simplify scan timing configuration

From: Hante Meuleman <[email protected]>

No need to pass timing configuration in local functions as they are static anyway.

---
 .../broadcom/brcm80211/brcmfmac/cfg80211.c         | 31 +++++++++-------------
 .../broadcom/brcm80211/brcmfmac/cfg80211.h         |  4 ---
 2 files changed, 12 insertions(+), 23 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +12 -19
index 771c581..4aebb2a 100644
@@ -91,6 +91,10 @@
 #define BRCMF_SCAN_JOIN_PASSIVE_DWELL_TIME_MS	400
 #define BRCMF_SCAN_JOIN_PROBE_INTERVAL_MS	20
 
+#define BRCMF_SCAN_CHANNEL_TIME		40
+#define BRCMF_SCAN_UNASSOC_TIME		40
+#define BRCMF_SCAN_PASSIVE_TIME		120
+
 #define BRCMF_ASSOC_PARAMS_FIXED_SIZE \
 	(sizeof(struct brcmf_assoc_params_le) - sizeof(u16))
 
@@ -5357,37 +5361,27 @@ roam_setup_done:
 }
 
 static s32
-brcmf_dongle_scantime(struct brcmf_if *ifp, s32 scan_assoc_time,
-		      s32 scan_unassoc_time, s32 scan_passive_time)
+brcmf_dongle_scantime(struct brcmf_if *ifp)
 {
 	s32 err = 0;
 
 	err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_SCAN_CHANNEL_TIME,
-				    scan_assoc_time);
+				    BRCMF_SCAN_CHANNEL_TIME);
 	if (err) {
-		if (err == -EOPNOTSUPP)
-			brcmf_dbg(INFO, "Scan assoc time is not supported\n");
-		else
-			brcmf_err("Scan assoc time error (%d)\n", err);
+		brcmf_err("Scan assoc time error (%d)\n", err);
 		goto dongle_scantime_out;
 	}
 	err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_SCAN_UNASSOC_TIME,
-				    scan_unassoc_time);
+				    BRCMF_SCAN_UNASSOC_TIME);
 	if (err) {
-		if (err == -EOPNOTSUPP)
-			brcmf_dbg(INFO, "Scan unassoc time is not supported\n");
-		else
-			brcmf_err("Scan unassoc time error (%d)\n", err);
+		brcmf_err("Scan unassoc time error (%d)\n", err);
 		goto dongle_scantime_out;
 	}
 
 	err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_SCAN_PASSIVE_TIME,
-				    scan_passive_time);
+				    BRCMF_SCAN_PASSIVE_TIME);
 	if (err) {
-		if (err == -EOPNOTSUPP)
-			brcmf_dbg(INFO, "Scan passive time is not supported\n");
-		else
-			brcmf_err("Scan passive time error (%d)\n", err);
+		brcmf_err("Scan passive time error (%d)\n", err);
 		goto dongle_scantime_out;
 	}
 
@@ -6089,8 +6083,7 @@ static s32 brcmf_config_dongle(struct brcmf_cfg80211_info *cfg)
 	/* make sure RF is ready for work */
 	brcmf_fil_cmd_int_set(ifp, BRCMF_C_UP, 0);
 
-	brcmf_dongle_scantime(ifp, WL_SCAN_CHANNEL_TIME,
-			      WL_SCAN_UNASSOC_TIME, WL_SCAN_PASSIVE_TIME);
+	brcmf_dongle_scantime(ifp);
 
 	power_mode = cfg->pwr_save ? PM_FAST : PM_OFF;
 	err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_PM, power_mode);
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +0 -4
index d492163..cf7a93d 100644
@@ -29,10 +29,6 @@
 #define WL_ROAM_TRIGGER_LEVEL		-75
 #define WL_ROAM_DELTA			20
 
-#define WL_SCAN_CHANNEL_TIME		40
-#define WL_SCAN_UNASSOC_TIME		40
-#define WL_SCAN_PASSIVE_TIME		120
-
 #define WL_ESCAN_BUF_SIZE		(1024 * 64)
 #define WL_ESCAN_TIMER_INTERVAL_MS	10000 /* E-Scan timeout */
 
Signature · 1 line
1.9.1
#2 lore raw

Re: [V2,01/13] brcmfmac: Simplify scan timing configuration

Quoted 10 lines

From: Hante Meuleman <[email protected]>

No need to pass timing configuration in local functions as they are static anyway.

Thanks, 12 patches applied to wireless-drivers-next.git:

1678ba8ed350 brcmfmac: Simplify scan timing configuration
675f5d82a73f brcmfmac: Use local storage for ssid iovar
4235edcdfc30 brcmfmac: Remove some redundant cfg80211 data
6c404f34f2bd brcmfmac: Cleanup pmksa cache handling code
a7b82d474171 brcmfmac: Make TDLS a detectable feature
fdf345642297 brcmfmac: Add support for PCIE 4350 revision 5 device 353c46ac9e53 brcmfmac: no interface combination check for single interface b0a790883ed4 brcmfmac: Fix IBSS setup
a7decc44a002 brcmfmac: fix waitqueue_active without memory barrier in brcmfmac driver 540313d8f954 brcmfmac: add 43242 device id for LG dongle
f3fb75038dd1 brcmfmac: Change error print in debug print
a41286aee42f brcmfmac: Move scheduled scan related interface layer structs

Kalle Valo

#3 lore raw

PATCH v2 2/13 brcmfmac: Use local storage for ssid iovar

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

---
 .../wireless/broadcom/brcm80211/brcmfmac/cfg80211.c    | 18 +++++++++---------
 .../wireless/broadcom/brcm80211/brcmfmac/cfg80211.h    |  7 -------
 2 files changed, 9 insertions(+), 16 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +9 -9
index 4aebb2a..b7b60f52 100644
@@ -1031,11 +1031,11 @@ brcmf_cfg80211_escan(struct wiphy *wiphy, struct brcmf_cfg80211_vif *vif,
 	struct brcmf_if *ifp = vif->ifp;
 	struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy);
 	struct cfg80211_ssid *ssids;
-	struct brcmf_cfg80211_scan_req *sr = &cfg->scan_req_int;
 	u32 passive_scan;
 	bool escan_req;
 	bool spec_scan;
 	s32 err;
+	struct brcmf_ssid_le ssid_le;
 	u32 SSID_len;
 
 	brcmf_dbg(SCAN, "START ESCAN\n");
@@ -1088,13 +1088,13 @@ brcmf_cfg80211_escan(struct wiphy *wiphy, struct brcmf_cfg80211_vif *vif,
 	} else {
 		brcmf_dbg(SCAN, "ssid \"%s\", ssid_len (%d)\n",
 			  ssids->ssid, ssids->ssid_len);
-		memset(&sr->ssid_le, 0, sizeof(sr->ssid_le));
-		SSID_len = min_t(u8, sizeof(sr->ssid_le.SSID), ssids->ssid_len);
-		sr->ssid_le.SSID_len = cpu_to_le32(0);
+		memset(&ssid_le, 0, sizeof(ssid_le));
+		SSID_len = min_t(u8, sizeof(ssid_le.SSID), ssids->ssid_len);
+		ssid_le.SSID_len = cpu_to_le32(0);
 		spec_scan = false;
 		if (SSID_len) {
-			memcpy(sr->ssid_le.SSID, ssids->ssid, SSID_len);
-			sr->ssid_le.SSID_len = cpu_to_le32(SSID_len);
+			memcpy(ssid_le.SSID, ssids->ssid, SSID_len);
+			ssid_le.SSID_len = cpu_to_le32(SSID_len);
 			spec_scan = true;
 		} else
 			brcmf_dbg(SCAN, "Broadcast scan\n");
@@ -1107,12 +1107,12 @@ brcmf_cfg80211_escan(struct wiphy *wiphy, struct brcmf_cfg80211_vif *vif,
 			goto scan_out;
 		}
 		brcmf_scan_config_mpc(ifp, 0);
-		err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SCAN,
-					     &sr->ssid_le, sizeof(sr->ssid_le));
+		err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SCAN, &ssid_le,
+					     sizeof(ssid_le));
 		if (err) {
 			if (err == -EBUSY)
 				brcmf_dbg(INFO, "BUSY: scan for \"%s\" canceled\n",
-					  sr->ssid_le.SSID);
+					  ssid_le.SSID);
 			else
 				brcmf_err("WLC_SCAN error (%d)\n", err);
 
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +0 -7
index cf7a93d..e77f137 100644
@@ -99,11 +99,6 @@ struct brcmf_cfg80211_conf {
 	struct ieee80211_channel channel;
 };
 
-/* basic structure of scan request */
-struct brcmf_cfg80211_scan_req {
-	struct brcmf_ssid_le ssid_le;
-};
-
 /* basic structure of information element */
 struct brcmf_cfg80211_ie {
 	u16 offset;
@@ -337,7 +332,6 @@ struct brcmf_cfg80211_vif_event {
  * @scan_request: cfg80211 scan request object.
  * @usr_sync: mainly for dongle up/down synchronization.
  * @bss_list: bss_list holding scanned ap information.
- * @scan_req_int: internal scan request object.
  * @bss_info: bss information for cfg80211 layer.
  * @ie: information element object for internal purpose.
  * @conn_info: association info.
@@ -372,7 +366,6 @@ struct brcmf_cfg80211_info {
 	struct brcmf_btcoex_info *btcoex;
 	struct cfg80211_scan_request *scan_request;
 	struct mutex usr_sync;
-	struct brcmf_cfg80211_scan_req scan_req_int;
 	struct wl_cfg80211_bss_info *bss_info;
 	struct brcmf_cfg80211_ie ie;
 	struct brcmf_cfg80211_connect_info conn_info;
Signature · 1 line
1.9.1
#4 lore raw

PATCH v2 3/13 brcmfmac: Remove some redundant cfg80211 data

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c |  1 -
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h | 10 ----------
 2 files changed, 11 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +0 -1
index b7b60f52..5432c46 100644
@@ -5203,7 +5203,6 @@ static void brcmf_init_conf(struct brcmf_cfg80211_conf *conf)
 	conf->rts_threshold = (u32)-1;
 	conf->retry_short = (u32)-1;
 	conf->retry_long = (u32)-1;
-	conf->tx_power = -1;
 }
 
 static void brcmf_register_event_handlers(struct brcmf_cfg80211_info *cfg)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +0 -10
index e77f137..ec8d1f8 100644
@@ -95,14 +95,6 @@ struct brcmf_cfg80211_conf {
 	u32 rts_threshold;
 	u32 retry_short;
 	u32 retry_long;
-	s32 tx_power;
-	struct ieee80211_channel channel;
-};
-
-/* basic structure of information element */
-struct brcmf_cfg80211_ie {
-	u16 offset;
-	u8 buf[WL_TLV_INFO_MAX];
 };
 
 /* security information with currently associated ap */
@@ -333,7 +325,6 @@ struct brcmf_cfg80211_vif_event {
  * @usr_sync: mainly for dongle up/down synchronization.
  * @bss_list: bss_list holding scanned ap information.
  * @bss_info: bss information for cfg80211 layer.
- * @ie: information element object for internal purpose.
  * @conn_info: association info.
  * @pmk_list: wpa2 pmk list.
  * @scan_status: scan activity on the dongle.
@@ -367,7 +358,6 @@ struct brcmf_cfg80211_info {
 	struct cfg80211_scan_request *scan_request;
 	struct mutex usr_sync;
 	struct wl_cfg80211_bss_info *bss_info;
-	struct brcmf_cfg80211_ie ie;
 	struct brcmf_cfg80211_connect_info conn_info;
 	struct brcmf_cfg80211_pmk_list *pmk_list;
 	unsigned long scan_status;
Signature · 1 line
1.9.1
#5 lore raw

PATCH v2 4/13 brcmfmac: Cleanup pmksa cache handling code

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

---
 .../broadcom/brcm80211/brcmfmac/cfg80211.c         | 131 +++++++++------------
 .../broadcom/brcm80211/brcmfmac/cfg80211.h         |   9 +-
 .../broadcom/brcm80211/brcmfmac/fwil_types.h       |  24 ++++
 .../broadcom/brcm80211/include/brcmu_wifi.h        |  23 ----
 4 files changed, 82 insertions(+), 105 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +57 -74
index 5432c46..564e533 100644
@@ -3223,26 +3223,22 @@ exit:
 }
 
 static __used s32
-brcmf_update_pmklist(struct net_device *ndev,
-		     struct brcmf_cfg80211_pmk_list *pmk_list, s32 err)
+brcmf_update_pmklist(struct brcmf_cfg80211_info *cfg, struct brcmf_if *ifp)
 {
-	int i, j;
-	u32 pmkid_len;
+	struct brcmf_pmk_list_le *pmk_list;
+	int i;
+	u32 npmk;
+	s32 err;
 
-	pmkid_len = le32_to_cpu(pmk_list->pmkids.npmkid);
+	pmk_list = &cfg->pmk_list;
+	npmk = le32_to_cpu(pmk_list->npmk);
 
-	brcmf_dbg(CONN, "No of elements %d\n", pmkid_len);
-	for (i = 0; i < pmkid_len; i++) {
-		brcmf_dbg(CONN, "PMKID[%d]: %pM =\n", i,
-			  &pmk_list->pmkids.pmkid[i].BSSID);
-		for (j = 0; j < WLAN_PMKID_LEN; j++)
-			brcmf_dbg(CONN, "%02x\n",
-				  pmk_list->pmkids.pmkid[i].PMKID[j]);
-	}
+	brcmf_dbg(CONN, "No of elements %d\n", npmk);
+	for (i = 0; i < npmk; i++)
+		brcmf_dbg(CONN, "PMK[%d]: %pM\n", i, &pmk_list->pmk[i].bssid);
 
-	if (!err)
-		brcmf_fil_iovar_data_set(netdev_priv(ndev), "pmkid_info",
-					 (char *)pmk_list, sizeof(*pmk_list));
+	err = brcmf_fil_iovar_data_set(ifp, "pmkid_info", pmk_list,
+				       sizeof(*pmk_list));
 
 	return err;
 }
@@ -3253,34 +3249,37 @@ brcmf_cfg80211_set_pmksa(struct wiphy *wiphy, struct net_device *ndev,
 {
 	struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy);
 	struct brcmf_if *ifp = netdev_priv(ndev);
-	struct pmkid_list *pmkids = &cfg->pmk_list->pmkids;
-	s32 err = 0;
-	u32 pmkid_len, i;
+	struct brcmf_pmksa *pmk = &cfg->pmk_list.pmk[0];
+	s32 err;
+	u32 npmk, i;
 
 	brcmf_dbg(TRACE, "Enter\n");
 	if (!check_vif_up(ifp->vif))
 		return -EIO;
 
-	pmkid_len = le32_to_cpu(pmkids->npmkid);
-	for (i = 0; i < pmkid_len; i++)
-		if (!memcmp(pmksa->bssid, pmkids->pmkid[i].BSSID, ETH_ALEN))
+	npmk = le32_to_cpu(cfg->pmk_list.npmk);
+	for (i = 0; i < npmk; i++)
+		if (!memcmp(pmksa->bssid, pmk[i].bssid, ETH_ALEN))
 			break;
-	if (i < WL_NUM_PMKIDS_MAX) {
-		memcpy(pmkids->pmkid[i].BSSID, pmksa->bssid, ETH_ALEN);
-		memcpy(pmkids->pmkid[i].PMKID, pmksa->pmkid, WLAN_PMKID_LEN);
-		if (i == pmkid_len) {
-			pmkid_len++;
-			pmkids->npmkid = cpu_to_le32(pmkid_len);
+	if (i < BRCMF_MAXPMKID) {
+		memcpy(pmk[i].bssid, pmksa->bssid, ETH_ALEN);
+		memcpy(pmk[i].pmkid, pmksa->pmkid, WLAN_PMKID_LEN);
+		if (i == npmk) {
+			npmk++;
+			cfg->pmk_list.npmk = cpu_to_le32(npmk);
 		}
-	} else
-		err = -EINVAL;
+	} else {
+		brcmf_err("Too many PMKSA entries cached %d\n", npmk);
+		return -EINVAL;
+	}
 
-	brcmf_dbg(CONN, "set_pmksa,IW_PMKSA_ADD - PMKID: %pM =\n",
-		  pmkids->pmkid[pmkid_len].BSSID);
-	for (i = 0; i < WLAN_PMKID_LEN; i++)
-		brcmf_dbg(CONN, "%02x\n", pmkids->pmkid[pmkid_len].PMKID[i]);
+	brcmf_dbg(CONN, "set_pmksa - PMK bssid: %pM =\n", pmk[npmk].bssid);
+	for (i = 0; i < WLAN_PMKID_LEN; i += 4)
+		brcmf_dbg(CONN, "%02x %02x %02x %02x\n", pmk[npmk].pmkid[i],
+			  pmk[npmk].pmkid[i + 1], pmk[npmk].pmkid[i + 2],
+			  pmk[npmk].pmkid[i + 3]);
 
-	err = brcmf_update_pmklist(ndev, cfg->pmk_list, err);
+	err = brcmf_update_pmklist(cfg, ifp);
 
 	brcmf_dbg(TRACE, "Exit\n");
 	return err;
@@ -3288,50 +3287,39 @@ brcmf_cfg80211_set_pmksa(struct wiphy *wiphy, struct net_device *ndev,
 
 static s32
 brcmf_cfg80211_del_pmksa(struct wiphy *wiphy, struct net_device *ndev,
-		      struct cfg80211_pmksa *pmksa)
+			 struct cfg80211_pmksa *pmksa)
 {
 	struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy);
 	struct brcmf_if *ifp = netdev_priv(ndev);
-	struct pmkid_list pmkid;
-	s32 err = 0;
-	u32 pmkid_len, i;
+	struct brcmf_pmksa *pmk = &cfg->pmk_list.pmk[0];
+	s32 err;
+	u32 npmk, i;
 
 	brcmf_dbg(TRACE, "Enter\n");
 	if (!check_vif_up(ifp->vif))
 		return -EIO;
 
-	memcpy(&pmkid.pmkid[0].BSSID, pmksa->bssid, ETH_ALEN);
-	memcpy(&pmkid.pmkid[0].PMKID, pmksa->pmkid, WLAN_PMKID_LEN);
+	brcmf_dbg(CONN, "del_pmksa - PMK bssid = %pM\n", &pmksa->bssid);
 
-	brcmf_dbg(CONN, "del_pmksa,IW_PMKSA_REMOVE - PMKID: %pM =\n",
-		  &pmkid.pmkid[0].BSSID);
-	for (i = 0; i < WLAN_PMKID_LEN; i++)
-		brcmf_dbg(CONN, "%02x\n", pmkid.pmkid[0].PMKID[i]);
-
-	pmkid_len = le32_to_cpu(cfg->pmk_list->pmkids.npmkid);
-	for (i = 0; i < pmkid_len; i++)
-		if (!memcmp
-		    (pmksa->bssid, &cfg->pmk_list->pmkids.pmkid[i].BSSID,
-		     ETH_ALEN))
+	npmk = le32_to_cpu(cfg->pmk_list.npmk);
+	for (i = 0; i < npmk; i++)
+		if (!memcmp(&pmksa->bssid, &pmk[i].bssid, ETH_ALEN))
 			break;
 
-	if ((pmkid_len > 0)
-	    && (i < pmkid_len)) {
-		memset(&cfg->pmk_list->pmkids.pmkid[i], 0,
-		       sizeof(struct pmkid));
-		for (; i < (pmkid_len - 1); i++) {
-			memcpy(&cfg->pmk_list->pmkids.pmkid[i].BSSID,
-			       &cfg->pmk_list->pmkids.pmkid[i + 1].BSSID,
-			       ETH_ALEN);
-			memcpy(&cfg->pmk_list->pmkids.pmkid[i].PMKID,
-			       &cfg->pmk_list->pmkids.pmkid[i + 1].PMKID,
+	if ((npmk > 0) && (i < npmk)) {
+		for (; i < (npmk - 1); i++) {
+			memcpy(&pmk[i].bssid, &pmk[i + 1].bssid, ETH_ALEN);
+			memcpy(&pmk[i].pmkid, &pmk[i + 1].pmkid,
 			       WLAN_PMKID_LEN);
 		}
-		cfg->pmk_list->pmkids.npmkid = cpu_to_le32(pmkid_len - 1);
-	} else
-		err = -EINVAL;
+		memset(&pmk[i], 0, sizeof(*pmk));
+		cfg->pmk_list.npmk = cpu_to_le32(npmk - 1);
+	} else {
+		brcmf_err("Cache entry not found\n");
+		return -EINVAL;
+	}
 
-	err = brcmf_update_pmklist(ndev, cfg->pmk_list, err);
+	err = brcmf_update_pmklist(cfg, ifp);
 
 	brcmf_dbg(TRACE, "Exit\n");
 	return err;
@@ -3343,14 +3331,14 @@ brcmf_cfg80211_flush_pmksa(struct wiphy *wiphy, struct net_device *ndev)
 {
 	struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy);
 	struct brcmf_if *ifp = netdev_priv(ndev);
-	s32 err = 0;
+	s32 err;
 
 	brcmf_dbg(TRACE, "Enter\n");
 	if (!check_vif_up(ifp->vif))
 		return -EIO;
 
-	memset(cfg->pmk_list, 0, sizeof(*cfg->pmk_list));
-	err = brcmf_update_pmklist(ndev, cfg->pmk_list, err);
+	memset(&cfg->pmk_list, 0, sizeof(cfg->pmk_list));
+	err = brcmf_update_pmklist(cfg, ifp);
 
 	brcmf_dbg(TRACE, "Exit\n");
 	return err;
@@ -5249,8 +5237,6 @@ static void brcmf_deinit_priv_mem(struct brcmf_cfg80211_info *cfg)
 	cfg->escan_ioctl_buf = NULL;
 	kfree(cfg->extra_buf);
 	cfg->extra_buf = NULL;
-	kfree(cfg->pmk_list);
-	cfg->pmk_list = NULL;
 }
 
 static s32 brcmf_init_priv_mem(struct brcmf_cfg80211_info *cfg)
@@ -5264,9 +5250,6 @@ static s32 brcmf_init_priv_mem(struct brcmf_cfg80211_info *cfg)
 	cfg->extra_buf = kzalloc(WL_EXTRA_BUF_MAX, GFP_KERNEL);
 	if (!cfg->extra_buf)
 		goto init_priv_mem_out;
-	cfg->pmk_list = kzalloc(sizeof(*cfg->pmk_list), GFP_KERNEL);
-	if (!cfg->pmk_list)
-		goto init_priv_mem_out;
 
 	return 0;
 
@@ -5971,7 +5954,7 @@ static int brcmf_setup_wiphy(struct wiphy *wiphy, struct brcmf_if *ifp)
 
 	wiphy->max_scan_ssids = WL_NUM_SCAN_MAX;
 	wiphy->max_scan_ie_len = BRCMF_SCAN_IE_LEN_MAX;
-	wiphy->max_num_pmkids = WL_NUM_PMKIDS_MAX;
+	wiphy->max_num_pmkids = BRCMF_MAXPMKID;
 
 	err = brcmf_setup_ifmodes(wiphy, ifp);
 	if (err)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +1 -8
index ec8d1f8..397d41b 100644
@@ -21,7 +21,6 @@
 #include <brcmu_d11.h>
 
 #define WL_NUM_SCAN_MAX			10
-#define WL_NUM_PMKIDS_MAX		MAXPMKID
 #define WL_TLV_INFO_MAX			1024
 #define WL_BSS_INFO_MAX			2048
 #define WL_ASSOC_INFO_MAX		512	/* assoc related fil max buf */
@@ -196,12 +195,6 @@ struct brcmf_cfg80211_assoc_ielen_le {
 	__le32 resp_len;
 };
 
-/* wpa2 pmk list */
-struct brcmf_cfg80211_pmk_list {
-	struct pmkid_list pmkids;
-	struct pmkid foo[MAXPMKID - 1];
-};
-
 /* dongle escan state */
 enum wl_escan_state {
 	WL_ESCAN_STATE_IDLE,
@@ -359,7 +352,7 @@ struct brcmf_cfg80211_info {
 	struct mutex usr_sync;
 	struct wl_cfg80211_bss_info *bss_info;
 	struct brcmf_cfg80211_connect_info conn_info;
-	struct brcmf_cfg80211_pmk_list *pmk_list;
+	struct brcmf_pmk_list_le pmk_list;
 	unsigned long scan_status;
 	struct brcmf_pub *pub;
 	u32 channel;
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h +24 -0
index 18483e7..e56eabc 100644
@@ -126,6 +126,8 @@
 #define BRCMF_TXBF_SU_BFR_CAP		BIT(0)
 #define BRCMF_TXBF_MU_BFR_CAP		BIT(1)
 
+#define	BRCMF_MAXPMKID			16	/* max # PMKID cache entries */
+
 /* join preference types for join_pref iovar */
 enum brcmf_join_pref_types {
 	BRCMF_JOIN_PREF_RSSI = 1,
@@ -646,4 +648,26 @@ struct brcmf_wowl_wakeind_le {
 	__le32 ucode_wakeind;
 };
 
+/**
+ * struct brcmf_pmksa - PMK Security Association
+ *
+ * @bssid: The AP's BSSID.
+ * @pmkid: he PMK material itself.
+ */
+struct brcmf_pmksa {
+	u8 bssid[ETH_ALEN];
+	u8 pmkid[WLAN_PMKID_LEN];
+};
+
+/**
+ * struct brcmf_pmk_list_le - List of pmksa's.
+ *
+ * @npmk: Number of pmksa's.
+ * @pmk: PMK SA information.
+ */
+struct brcmf_pmk_list_le {
+	__le32 npmk;
+	struct brcmf_pmksa pmk[BRCMF_MAXPMKID];
+};
+
 #endif /* FWIL_TYPES_H_ */
drivers/net/wireless/broadcom/brcm80211/include/brcmu_wifi.h +0 -23
index 76b5d3a..3f68dd5 100644
@@ -237,9 +237,6 @@ static inline bool ac_bitmap_tst(u8 bitmap, int prec)
 #define WPA2_AUTH_RESERVED4	0x0400
 #define WPA2_AUTH_RESERVED5	0x0800
 
-/* pmkid */
-#define	MAXPMKID		16
-
 #define DOT11_DEFAULT_RTS_LEN		2347
 #define DOT11_DEFAULT_FRAG_LEN		2346
 
@@ -251,24 +248,4 @@ static inline bool ac_bitmap_tst(u8 bitmap, int prec)
 #define HT_CAP_RX_STBC_NO		0x0
 #define HT_CAP_RX_STBC_ONE_STREAM	0x1
 
-struct pmkid {
-	u8 BSSID[ETH_ALEN];
-	u8 PMKID[WLAN_PMKID_LEN];
-};
-
-struct pmkid_list {
-	__le32 npmkid;
-	struct pmkid pmkid[1];
-};
-
-struct pmkid_cand {
-	u8 BSSID[ETH_ALEN];
-	u8 preauth;
-};
-
-struct pmkid_cand_list {
-	u32 npmkid_cand;
-	struct pmkid_cand pmkid_cand[1];
-};
-
 #endif				/* _BRCMU_WIFI_H_ */
Signature · 1 line
1.9.1
#6 lore raw

PATCH v2 5/13 brcmfmac: Make TDLS a detectable feature

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

---
 .../wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 21 ++++++++++++---------
 .../wireless/broadcom/brcm80211/brcmfmac/feature.c  |  1 +
 .../wireless/broadcom/brcm80211/brcmfmac/feature.h  |  4 +++-
 3 files changed, 16 insertions(+), 10 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +12 -9
index 564e533..8557566 100644
@@ -5983,8 +5983,9 @@ static int brcmf_setup_wiphy(struct wiphy *wiphy, struct brcmf_if *ifp)
 	wiphy->n_cipher_suites = ARRAY_SIZE(__wl_cipher_suites);
 	wiphy->flags |= WIPHY_FLAG_PS_ON_BY_DEFAULT |
 			WIPHY_FLAG_OFFCHAN_TX |
-			WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL |
-			WIPHY_FLAG_SUPPORTS_TDLS;
+			WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
+	if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_TDLS))
+		wiphy->flags |= WIPHY_FLAG_SUPPORTS_TDLS;
 	if (!brcmf_roamoff)
 		wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM;
 	wiphy->mgmt_stypes = brcmf_txrx_stypes;
@@ -6376,13 +6377,15 @@ struct brcmf_cfg80211_info *brcmf_cfg80211_attach(struct brcmf_pub *drvr,
 		goto wiphy_unreg_out;
 	}
 
-	err = brcmf_fil_iovar_int_set(ifp, "tdls_enable", 1);
-	if (err) {
-		brcmf_dbg(INFO, "TDLS not enabled (%d)\n", err);
-		wiphy->flags &= ~WIPHY_FLAG_SUPPORTS_TDLS;
-	} else {
-		brcmf_fweh_register(cfg->pub, BRCMF_E_TDLS_PEER_EVENT,
-				    brcmf_notify_tdls_peer_event);
+	if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_TDLS)) {
+		err = brcmf_fil_iovar_int_set(ifp, "tdls_enable", 1);
+		if (err) {
+			brcmf_dbg(INFO, "TDLS not enabled (%d)\n", err);
+			wiphy->flags &= ~WIPHY_FLAG_SUPPORTS_TDLS;
+		} else {
+			brcmf_fweh_register(cfg->pub, BRCMF_E_TDLS_PEER_EVENT,
+					    brcmf_notify_tdls_peer_event);
+		}
 	}
 
 	/* (re-) activate FWEH event handling */
drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c +1 -0
index ba52494..d9d1ca4 100644
@@ -138,6 +138,7 @@ void brcmf_feat_attach(struct brcmf_pub *drvr)
 		brcmf_feat_iovar_int_set(ifp, BRCMF_FEAT_MBSS, "mbss", 0);
 	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_P2P, "p2p");
 	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_RSDB, "rsdb_mode");
+	brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_TDLS, "tdls_enable");
 
 	if (brcmf_feature_disable) {
 		brcmf_dbg(INFO, "Features: 0x%02x, disable: 0x%02x\n",
drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h +3 -1
index 5381758..1390656 100644
@@ -25,6 +25,7 @@
  * WOWL: Wake-On-WLAN.
  * P2P: peer-to-peer
  * RSDB: Real Simultaneous Dual Band
+ * TDLS: Tunneled Direct Link Setup
  */
 #define BRCMF_FEAT_LIST \
 	BRCMF_FEAT_DEF(MBSS) \
@@ -32,7 +33,8 @@
 	BRCMF_FEAT_DEF(PNO) \
 	BRCMF_FEAT_DEF(WOWL) \
 	BRCMF_FEAT_DEF(P2P) \
-	BRCMF_FEAT_DEF(RSDB)
+	BRCMF_FEAT_DEF(RSDB) \
+	BRCMF_FEAT_DEF(TDLS)
 
 /*
  * Quirks:
Signature · 1 line
1.9.1
#7 lore raw

PATCH v2 6/13 brcmfmac: Add support for PCIE 4350 revision 5 device

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

Change-Id I72b519ec6a7ff0d36f076df06d042f0c5894142c

Reviewed-on: http://hnd-swgit.sj.broadcom.com:8080/5513

---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +3 -1
index b5a4247..4ebc53c 100644
@@ -46,6 +46,7 @@ enum brcmf_pcie_state {
 
 BRCMF_FW_NVRAM_DEF(43602, "brcmfmac43602-pcie.bin", "brcmfmac43602-pcie.txt");
 BRCMF_FW_NVRAM_DEF(4350, "brcmfmac4350-pcie.bin", "brcmfmac4350-pcie.txt");
+BRCMF_FW_NVRAM_DEF(4350C, "brcmfmac4350c2-pcie.bin", "brcmfmac4350c2-pcie.txt");
 BRCMF_FW_NVRAM_DEF(4356, "brcmfmac4356-pcie.bin", "brcmfmac4356-pcie.txt");
 BRCMF_FW_NVRAM_DEF(43570, "brcmfmac43570-pcie.bin", "brcmfmac43570-pcie.txt");
 BRCMF_FW_NVRAM_DEF(4358, "brcmfmac4358-pcie.bin", "brcmfmac4358-pcie.txt");
@@ -56,7 +57,8 @@ BRCMF_FW_NVRAM_DEF(4371, "brcmfmac4371-pcie.bin", "brcmfmac4371-pcie.txt");
 
 static struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = {
 	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_43602_CHIP_ID, 0xFFFFFFFF, 43602),
-	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_4350_CHIP_ID, 0xFFFFFFFF, 4350),
+	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_4350_CHIP_ID, 0x000000FF, 4350C),
+	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_4350_CHIP_ID, 0xFFFFFF00, 4350),
 	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_4356_CHIP_ID, 0xFFFFFFFF, 4356),
 	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_43567_CHIP_ID, 0xFFFFFFFF, 43570),
 	BRCMF_FW_NVRAM_ENTRY(BRCM_CC_43569_CHIP_ID, 0xFFFFFFFF, 43570),
Signature · 1 line
1.9.1
#8 lore raw

Re: [PATCH V2 06/13] brcmfmac: Add support for PCIE 4350 revision 5 device

Quoted 8 lines · Arend van Spriel

From: Hante Meuleman <[email protected]>

Change-Id I72b519ec6a7ff0d36f076df06d042f0c5894142c

Reviewed-on: http://hnd-swgit.sj.broadcom.com:8080/5513

You forgot this one. But I'll fix it before I apply it, unless I forget it :)

Signature · 1 line
Kalle Valo
#9 lore raw

PATCH v2 7/13 brcmfmac: no interface combination check for single interface

In reply to Arend van Spriel

The interface combinations are intended for use-case in which the driver handles multiple interface concurrently. This means that the combinations do not need to be checked when there is only a single interface active.

---
 .../net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c    | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +11 -3
index 8557566..3ac5cf7 100644
@@ -396,15 +396,23 @@ static int brcmf_vif_change_validate(struct brcmf_cfg80211_info *cfg,
 {
 	int iftype_num[NUM_NL80211_IFTYPES];
 	struct brcmf_cfg80211_vif *pos;
+	bool check_combos = false;
+	int ret = 0;
 
 	memset(&iftype_num[0], 0, sizeof(iftype_num));
 	list_for_each_entry(pos, &cfg->vif_list, list)
-		if (pos == vif)
+		if (pos == vif) {
 			iftype_num[new_type]++;
-		else
+		} else {
+			/* concurrent interfaces so need check combinations */
+			check_combos = true;
 			iftype_num[pos->wdev.iftype]++;
+		}
 
-	return cfg80211_check_combinations(cfg->wiphy, 1, 0, iftype_num);
+	if (check_combos)
+		ret = cfg80211_check_combinations(cfg->wiphy, 1, 0, iftype_num);
+
+	return ret;
 }
 
 static int brcmf_vif_add_validate(struct brcmf_cfg80211_info *cfg,
Signature · 1 line
1.9.1
#10 lore raw

PATCH v2 8/13 brcmfmac: Fix IBSS setup

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

IBSS got broken over time. Disconnect events should not be given for IBSS mode and connect events for IBSS need to have channel information.

---
 .../net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +9 -8
index 3ac5cf7..17658b3 100644
@@ -1273,17 +1273,17 @@ static void brcmf_link_down(struct brcmf_cfg80211_vif *vif, u16 reason)
 
 	brcmf_dbg(TRACE, "Enter\n");
 
-	if (test_bit(BRCMF_VIF_STATUS_CONNECTED, &vif->sme_state)) {
+	if (test_and_clear_bit(BRCMF_VIF_STATUS_CONNECTED, &vif->sme_state)) {
 		brcmf_dbg(INFO, "Call WLC_DISASSOC to stop excess roaming\n ");
 		err = brcmf_fil_cmd_data_set(vif->ifp,
 					     BRCMF_C_DISASSOC, NULL, 0);
 		if (err) {
 			brcmf_err("WLC_DISASSOC failed (%d)\n", err);
 		}
-		clear_bit(BRCMF_VIF_STATUS_CONNECTED, &vif->sme_state);
-		cfg80211_disconnected(vif->wdev.netdev, reason, NULL, 0,
-				      true, GFP_KERNEL);
-
+		if ((vif->wdev.iftype == NL80211_IFTYPE_STATION) ||
+		    (vif->wdev.iftype == NL80211_IFTYPE_P2P_CLIENT))
+			cfg80211_disconnected(vif->wdev.netdev, reason, NULL, 0,
+					      true, GFP_KERNEL);
 	}
 	clear_bit(BRCMF_VIF_STATUS_CONNECTING, &vif->sme_state);
 	clear_bit(BRCMF_SCAN_STATUS_SUPPRESS, &cfg->scan_status);
@@ -2697,8 +2697,8 @@ static s32 brcmf_inform_bss(struct brcmf_cfg80211_info *cfg)
 	return err;
 }
 
-static s32 wl_inform_ibss(struct brcmf_cfg80211_info *cfg,
-			  struct net_device *ndev, const u8 *bssid)
+static s32 brcmf_inform_ibss(struct brcmf_cfg80211_info *cfg,
+			     struct net_device *ndev, const u8 *bssid)
 {
 	struct wiphy *wiphy = cfg_to_wiphy(cfg);
 	struct ieee80211_channel *notify_channel;
@@ -2743,6 +2743,7 @@ static s32 wl_inform_ibss(struct brcmf_cfg80211_info *cfg,
 		band = wiphy->bands[IEEE80211_BAND_5GHZ];
 
 	freq = ieee80211_channel_to_frequency(ch.chnum, band->band);
+	cfg->channel = freq;
 	notify_channel = ieee80211_get_channel(wiphy, freq);
 
 	notify_capability = le16_to_cpu(bi->capability);
@@ -5071,9 +5072,9 @@ brcmf_notify_connect_status(struct brcmf_if *ifp,
 	} else if (brcmf_is_linkup(e)) {
 		brcmf_dbg(CONN, "Linkup\n");
 		if (brcmf_is_ibssmode(ifp->vif)) {
+			brcmf_inform_ibss(cfg, ndev, e->addr);
 			chan = ieee80211_get_channel(cfg->wiphy, cfg->channel);
 			memcpy(profile->bssid, e->addr, ETH_ALEN);
-			wl_inform_ibss(cfg, ndev, e->addr);
 			cfg80211_ibss_joined(ndev, e->addr, chan, GFP_KERNEL);
 			clear_bit(BRCMF_VIF_STATUS_CONNECTING,
 				  &ifp->vif->sme_state);
Signature · 1 line
1.9.1
#11 lore raw

PATCH v2 9/13 brcmfmac: fix waitqueue_active without memory barrier in brcmfmac driver

In reply to Arend van Spriel

From: Kosuke Tatsukawa <[email protected]>

brcmf_msgbuf_ioctl_resp_wake() seems to be missing a memory barrier which might cause the waker to not notice the waiter and miss sending a wake_up as in the following figure.

brcmf_msgbuf_ioctl_resp_wake brcmf_msgbuf_ioctl_resp_wait
------------------------------------------------------------------------
if (waitqueue_active(&msgbuf->ioctl_resp_wait))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
/* wait_event_timeout */

				        /* __wait_event_timeout */
					 /* ___wait_event */
					 prepare_to_wait_event(&wq, &__wait,
					   state);
					 if (msgbuf->ctl_completed)
					 ...

msgbuf->ctl_completed = true;
schedule_timeout(__ret))
------------------------------------------------------------------------

There are three other place in drivers/net/wireless/brcm80211/brcmfmac/ which have similar code. The attached patch removes the call to waitqueue_active() leaving just wake_up() behind. This fixes the problem because the call to spin_lock_irqsave() in wake_up() will be an ACQUIRE operation.

I found this issue when I was looking through the linux source code for places calling waitqueue_active() before wake_up*(), but without preceding memory barriers, after sending a patch to fix a similar issue in drivers/tty/n_tty.c (Details about the original issue can be found here: https://lkml.org/lkml/2015/9/28/849).

---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c | 3 +--
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c   | 6 ++----
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c    | 3 +--
 3 files changed, 4 insertions(+), 8 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c +1 -2
index 44e618f..5df9138 100644
@@ -473,8 +473,7 @@ static int brcmf_msgbuf_ioctl_resp_wait(struct brcmf_msgbuf *msgbuf)
 static void brcmf_msgbuf_ioctl_resp_wake(struct brcmf_msgbuf *msgbuf)
 {
 	msgbuf->ctl_completed = true;
-	if (waitqueue_active(&msgbuf->ioctl_resp_wait))
-		wake_up(&msgbuf->ioctl_resp_wait);
+	wake_up(&msgbuf->ioctl_resp_wait);
 }
 
 
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c +2 -4
index 9fa3a3a..ceb2a75 100644
@@ -1678,8 +1678,7 @@ static int brcmf_sdio_dcmd_resp_wait(struct brcmf_sdio *bus, uint *condition,
 
 static int brcmf_sdio_dcmd_resp_wake(struct brcmf_sdio *bus)
 {
-	if (waitqueue_active(&bus->dcmd_resp_wait))
-		wake_up_interruptible(&bus->dcmd_resp_wait);
+	wake_up_interruptible(&bus->dcmd_resp_wait);
 
 	return 0;
 }
@@ -2003,8 +2002,7 @@ static uint brcmf_sdio_readframes(struct brcmf_sdio *bus, uint maxframes)
 static void
 brcmf_sdio_wait_event_wakeup(struct brcmf_sdio *bus)
 {
-	if (waitqueue_active(&bus->ctrl_wait))
-		wake_up_interruptible(&bus->ctrl_wait);
+	wake_up_interruptible(&bus->ctrl_wait);
 	return;
 }
 
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c +1 -2
index ccde559..23eaf0f 100644
@@ -196,8 +196,7 @@ static int brcmf_usb_ioctl_resp_wait(struct brcmf_usbdev_info *devinfo)
 
 static void brcmf_usb_ioctl_resp_wake(struct brcmf_usbdev_info *devinfo)
 {
-	if (waitqueue_active(&devinfo->ioctl_resp_wait))
-		wake_up(&devinfo->ioctl_resp_wait);
+	wake_up(&devinfo->ioctl_resp_wait);
 }
 
 static void
Signature · 1 line
1.9.1
#12 lore raw

PATCH v2 10/13 brcmfmac: add 43242 device id for LG dongle

In reply to Arend van Spriel

Got a hint on IRC that a 43242 dongle for LG smart TV's works with brcmfmac:

Quoted 8 lines

Hello - I recently got a LG AN-WF500 wireless dongle for LG's SmartTVs. From the information I gathered it uses a Broadcom chipset BCM43242. The device should have been supported by brcmfmac kernel driver if it used USB IDs 0a5c:bd1f.
My device however identifies itself as "ID 043e:3101 LG Electronics USA, Inc.". I then tried adding the USB ID to the driver with
"echo "043e 3101" > /sys/bus/usb/drivers/brcmfmac/new_id" and it just works. The kernel provides the following information.

Quoted 6 lines
[15958.851291] usb 3-1.1.3: new high-speed USB device number 53 using ehci-pci
[15958.946723] usb 3-1.1.3: New USB device found, idVendor=043e, idProduct=3101
[15958.946728] usb 3-1.1.3: New USB device strings: Mfr=1, Product=4, SerialNumber=3
[15958.946731] usb 3-1.1.3: Product: Composite Wireless Adapter
[15958.946733] usb 3-1.1.3: Manufacturer: Broadcom
[15958.946735] usb 3-1.1.3: SerialNumber: 28458
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c        | 1 +
 drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++
 2 files changed, 3 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c +1 -0
index 23eaf0f..66c26a9 100644
@@ -1452,6 +1452,7 @@ static struct usb_device_id brcmf_usb_devid_table[] = {
 	BRCMF_USB_DEVICE(BRCM_USB_43236_DEVICE_ID),
 	BRCMF_USB_DEVICE(BRCM_USB_43242_DEVICE_ID),
 	BRCMF_USB_DEVICE(BRCM_USB_43569_DEVICE_ID),
+	{ USB_DEVICE(BRCM_USB_VENDOR_ID_LG, BRCM_USB_43242_LG_DEVICE_ID) },
 	/* special entry for device with firmware loaded and running */
 	BRCMF_USB_DEVICE(BRCM_USB_BCMFW_DEVICE_ID),
 	{ /* end: all zeroes */ }
drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h +2 -0
index 4092d27..699f2c2 100644
@@ -21,6 +21,7 @@
 #include <linux/mmc/sdio_ids.h>
 
 #define BRCM_USB_VENDOR_ID_BROADCOM	0x0a5c
+#define BRCM_USB_VENDOR_ID_LG		0x043e
 #define BRCM_PCIE_VENDOR_ID_BROADCOM	PCI_VENDOR_ID_BROADCOM
 
 /* Chipcommon Core Chip IDs */
@@ -57,6 +58,7 @@
 #define BRCM_USB_43143_DEVICE_ID	0xbd1e
 #define BRCM_USB_43236_DEVICE_ID	0xbd17
 #define BRCM_USB_43242_DEVICE_ID	0xbd1f
+#define BRCM_USB_43242_LG_DEVICE_ID	0x3101
 #define BRCM_USB_43569_DEVICE_ID	0xbd27
 #define BRCM_USB_BCMFW_DEVICE_ID	0x0bdc
 
Signature · 1 line
1.9.1
#13 lore raw

PATCH v2 11/13 brcmfmac: Change error print in debug print

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

The pcie suspend and resume routines contain some error prints, which should have been debug prints.

Change-Id Ibafe5d38301ee8f5e86889259ddeaea4dcae4cee

Reviewed-on: http://hnd-swgit.sj.broadcom.com:8080/5581

---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +2 -2
index 4ebc53c..3d2d790 100644
@@ -1875,7 +1875,7 @@ static int brcmf_pcie_pm_enter_D3(struct device *dev)
 	struct brcmf_pciedev_info *devinfo;
 	struct brcmf_bus *bus;
 
-	brcmf_err("Enter\n");
+	brcmf_dbg(PCIE, "Enter\n");
 
 	bus = dev_get_drvdata(dev);
 	devinfo = bus->bus_priv.pcie->devinfo;
@@ -1906,7 +1906,7 @@ static int brcmf_pcie_pm_leave_D3(struct device *dev)
 	struct pci_dev *pdev;
 	int err;
 
-	brcmf_err("Enter\n");
+	brcmf_dbg(PCIE, "Enter\n");
 
 	bus = dev_get_drvdata(dev);
 	devinfo = bus->bus_priv.pcie->devinfo;
Signature · 1 line
1.9.1
#14 lore raw

Re: [PATCH V2 11/13] brcmfmac: Change error print in debug print

Quoted 5 lines · Arend van Spriel

From: Hante Meuleman <[email protected]>

The pcie suspend and resume routines contain some error prints, which should have been debug prints.

Quoted 7 lines
Change-Id Ibafe5d38301ee8f5e86889259ddeaea4dcae4cee

Reviewed-on: http://hnd-swgit.sj.broadcom.com:8080/5581

I'll fix this one also.

Signature · 1 line
Kalle Valo
#15 lore raw

Re: [PATCH V2 11/13] brcmfmac: Change error print in debug print

Quoted 15 lines · Kalle Valo
Quoted 5 lines · Arend van Spriel

From: Hante Meuleman <[email protected]>

The pcie suspend and resume routines contain some error prints, which should have been debug prints.

Quoted 7 lines
Change-Id Ibafe5d38301ee8f5e86889259ddeaea4dcae4cee

Reviewed-on: http://hnd-swgit.sj.broadcom.com:8080/5581

Quoted 1 line

I'll fix this one also.

Thanks, Kalle

I could blame gedit, but that is a bit lame. Sorry for the inconvenience.

Regards,
Arend

#16 lore raw

PATCH v2 12/13 brcmfmac: Move scheduled scan related interface layer structs

In reply to Arend van Spriel

From: Hante Meuleman <[email protected]>

All interface layer related to scheduled scan are moved in fwil_types.h

---
 .../broadcom/brcm80211/brcmfmac/cfg80211.h         | 81 ----------------------
 .../broadcom/brcm80211/brcmfmac/fwil_types.h       | 81 ++++++++++++++++++++++
 2 files changed, 81 insertions(+), 81 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +0 -81
index 397d41b..c17b6d5 100644
@@ -211,87 +211,6 @@ struct escan_info {
 };
 
 /**
- * struct brcmf_pno_param_le - PNO scan configuration parameters
- *
- * @version: PNO parameters version.
- * @scan_freq: scan frequency.
- * @lost_network_timeout: #sec. to declare discovered network as lost.
- * @flags: Bit field to control features of PFN such as sort criteria auto
- *	enable switch and background scan.
- * @rssi_margin: Margin to avoid jitter for choosing a PFN based on RSSI sort
- *	criteria.
- * @bestn: number of best networks in each scan.
- * @mscan: number of scans recorded.
- * @repeat: minimum number of scan intervals before scan frequency changes
- *	in adaptive scan.
- * @exp: exponent of 2 for maximum scan interval.
- * @slow_freq: slow scan period.
- */
-struct brcmf_pno_param_le {
-	__le32 version;
-	__le32 scan_freq;
-	__le32 lost_network_timeout;
-	__le16 flags;
-	__le16 rssi_margin;
-	u8 bestn;
-	u8 mscan;
-	u8 repeat;
-	u8 exp;
-	__le32 slow_freq;
-};
-
-/**
- * struct brcmf_pno_net_param_le - scan parameters per preferred network.
- *
- * @ssid: ssid name and its length.
- * @flags: bit2: hidden.
- * @infra: BSS vs IBSS.
- * @auth: Open vs Closed.
- * @wpa_auth: WPA type.
- * @wsec: wsec value.
- */
-struct brcmf_pno_net_param_le {
-	struct brcmf_ssid_le ssid;
-	__le32 flags;
-	__le32 infra;
-	__le32 auth;
-	__le32 wpa_auth;
-	__le32 wsec;
-};
-
-/**
- * struct brcmf_pno_net_info_le - information per found network.
- *
- * @bssid: BSS network identifier.
- * @channel: channel number only.
- * @SSID_len: length of ssid.
- * @SSID: ssid characters.
- * @RSSI: receive signal strength (in dBm).
- * @timestamp: age in seconds.
- */
-struct brcmf_pno_net_info_le {
-	u8 bssid[ETH_ALEN];
-	u8 channel;
-	u8 SSID_len;
-	u8 SSID[32];
-	__le16	RSSI;
-	__le16	timestamp;
-};
-
-/**
- * struct brcmf_pno_scanresults_le - result returned in PNO NET FOUND event.
- *
- * @version: PNO version identifier.
- * @status: indicates completion status of PNO scan.
- * @count: amount of brcmf_pno_net_info_le entries appended.
- */
-struct brcmf_pno_scanresults_le {
-	__le32 version;
-	__le32 status;
-	__le32 count;
-};
-
-/**
  * struct brcmf_cfg80211_vif_event - virtual interface event information.
  *
  * @vif_wq: waitqueue awaiting interface event from firmware.
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h +81 -0

85 lines not on this page · raw message

Signature · 1 line
1.9.1
#17 lore raw

PATCH v2 13/13 brcmfmac: add arp offload ip address table configuration support

In reply to Arend van Spriel

From: Franky Lin <[email protected]>

Obtain ipv4 address through inetaddr notification for ARP offload host ip table configuration.

---
 .../wireless/broadcom/brcm80211/brcmfmac/core.c    | 108 +++++++++++++++++++++
 .../wireless/broadcom/brcm80211/brcmfmac/core.h    |   2 +
 2 files changed, 110 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c +108 -0
index 3a39192..2631f6f 100644
@@ -17,6 +17,7 @@
 #include <linux/kernel.h>
 #include <linux/etherdevice.h>
 #include <linux/module.h>
+#include <linux/inetdevice.h>
 #include <net/cfg80211.h>
 #include <net/rtnetlink.h>
 #include <brcmu_utils.h>
@@ -620,6 +621,8 @@ static int brcmf_netdev_stop(struct net_device *ndev)
 
 	brcmf_cfg80211_down(ndev);
 
+	brcmf_fil_iovar_data_set(ifp, "arp_hostip_clear", NULL, 0);
+
 	brcmf_net_setcarrier(ifp, false);
 
 	return 0;
@@ -940,6 +943,98 @@ int brcmf_get_next_free_bsscfgidx(struct brcmf_pub *drvr)
 	return available ? bsscfgidx : -ENOMEM;
 }
 
+#ifdef CONFIG_INET
+#define ARPOL_MAX_ENTRIES	8
+static int brcmf_inetaddr_changed(struct notifier_block *nb,
+				  unsigned long action, void *data)
+{
+	struct brcmf_pub *drvr = container_of(nb, struct brcmf_pub,
+					      inetaddr_notifier);
+	struct in_ifaddr *ifa = data;
+	struct net_device *ndev = ifa->ifa_dev->dev;
+	struct brcmf_if *ifp;
+	int idx, i, ret;
+	u32 val;
+	u32 addr_table[ARPOL_MAX_ENTRIES] = {0};
+
+	/* Find out if the notification is meant for us */
+	for (idx = 0; idx < BRCMF_MAX_IFS; idx++) {
+		ifp = drvr->iflist[idx];
+		if (ifp && ifp->ndev == ndev)
+			break;
+		if (idx == BRCMF_MAX_IFS - 1)
+			return NOTIFY_DONE;
+	}
+
+	/* check if arp offload is supported */
+	ret = brcmf_fil_iovar_int_get(ifp, "arpoe", &val);
+	if (ret)
+		return NOTIFY_OK;
+
+	/* old version only support primary index */
+	ret = brcmf_fil_iovar_int_get(ifp, "arp_version", &val);
+	if (ret)
+		val = 1;
+	if (val == 1)
+		ifp = drvr->iflist[0];
+
+	/* retrieve the table from firmware */
+	ret = brcmf_fil_iovar_data_get(ifp, "arp_hostip", addr_table,
+				       sizeof(addr_table));
+	if (ret) {
+		brcmf_err("fail to get arp ip table err:%d\n", ret);
+		return NOTIFY_OK;
+	}
+
+	for (i = 0; i < ARPOL_MAX_ENTRIES; i++)
+		if (ifa->ifa_address == addr_table[i])
+			break;
+
+	switch (action) {
+	case NETDEV_UP:
+		if (i == ARPOL_MAX_ENTRIES) {
+			brcmf_dbg(TRACE, "add %pI4 to arp table\n",
+				  &ifa->ifa_address);
+			/* set it directly */
+			ret = brcmf_fil_iovar_int_set(ifp, "arp_hostip",
+						      ifa->ifa_address);
+			if (ret)
+				brcmf_err("add arp ip err %d\n", ret);
+		}
+		break;
+	case NETDEV_DOWN:
+		if (i < ARPOL_MAX_ENTRIES) {
+			addr_table[i] = 0;
+			brcmf_dbg(TRACE, "remove %pI4 from arp table\n",
+				  &ifa->ifa_address);
+			/* clear the table in firmware */
+			ret = brcmf_fil_iovar_data_set(ifp, "arp_hostip_clear",
+						       NULL, 0);
+			if (ret) {
+				brcmf_err("fail to clear arp ip table err:%d\n",
+					  ret);
+				return NOTIFY_OK;
+			}
+			for (i = 0; i < ARPOL_MAX_ENTRIES; i++) {
+				if (addr_table[i] != 0) {
+					brcmf_fil_iovar_int_set(ifp,
+								"arp_hostip",
+								addr_table[i]);
+					if (ret)
+						brcmf_err("add arp ip err %d\n",
+							  ret);
+				}
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+#endif
+
 int brcmf_attach(struct device *dev)
 {
 	struct brcmf_pub *drvr = NULL;
@@ -1068,6 +1163,15 @@ int brcmf_bus_start(struct device *dev)
 		if (p2p_ifp)
 			ret = brcmf_net_p2p_attach(p2p_ifp);
 	}
+
+	if (ret)
+		goto fail;
+
+#ifdef CONFIG_INET
+	drvr->inetaddr_notifier.notifier_call = brcmf_inetaddr_changed;
+	ret = register_inetaddr_notifier(&drvr->inetaddr_notifier);
+#endif
+
 fail:
 	if (ret < 0) {
 		brcmf_err("failed: %d\n", ret);
@@ -1133,6 +1237,10 @@ void brcmf_detach(struct device *dev)
 	if (drvr == NULL)
 		return;
 
+#ifdef CONFIG_INET
+	unregister_inetaddr_notifier(&drvr->inetaddr_notifier);
+#endif
+
 	/* stop firmware event handling */
 	brcmf_fweh_detach(drvr);
 	if (drvr->config)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h +2 -0
index 77d8239..6018af7 100644
@@ -141,6 +141,8 @@ struct brcmf_pub {
 #ifdef DEBUG
 	struct dentry *dbgfs_dir;
 #endif
+
+	struct notifier_block inetaddr_notifier;
 };
 
 /* forward declarations */
Signature · 1 line
1.9.1
#18 lore raw

Re: [PATCH V2 13/13] brcmfmac: add arp offload ip address table configuration support

Quoted 4 lines · Arend van Spriel

From: Franky Lin <[email protected]>

Obtain ipv4 address through inetaddr notification for ARP offload host ip table configuration.

Turns out this patch has a sparse warning, ie. would not work on big-endian system. We have a fix for that. Should I mark this patch as dropped in patchwork?

Regards,
Arend

Quoted 168 lines
---
  .../wireless/broadcom/brcm80211/brcmfmac/core.c    | 108 +++++++++++++++++++++
  .../wireless/broadcom/brcm80211/brcmfmac/core.h    |   2 +
  2 files changed, 110 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c +108 -0
index 3a39192..2631f6f 100644
@@ -17,6 +17,7 @@
  #include <linux/kernel.h>
  #include <linux/etherdevice.h>
  #include <linux/module.h>
+#include <linux/inetdevice.h>
  #include <net/cfg80211.h>
  #include <net/rtnetlink.h>
  #include <brcmu_utils.h>
@@ -620,6 +621,8 @@ static int brcmf_netdev_stop(struct net_device *ndev)
 
  	brcmf_cfg80211_down(ndev);
 
+	brcmf_fil_iovar_data_set(ifp, "arp_hostip_clear", NULL, 0);
+
  	brcmf_net_setcarrier(ifp, false);
 
  	return 0;
@@ -940,6 +943,98 @@ int brcmf_get_next_free_bsscfgidx(struct brcmf_pub *drvr)
  	return available ? bsscfgidx : -ENOMEM;
  }
 
+#ifdef CONFIG_INET
+#define ARPOL_MAX_ENTRIES	8
+static int brcmf_inetaddr_changed(struct notifier_block *nb,
+				  unsigned long action, void *data)
+{
+	struct brcmf_pub *drvr = container_of(nb, struct brcmf_pub,
+					      inetaddr_notifier);
+	struct in_ifaddr *ifa = data;
+	struct net_device *ndev = ifa->ifa_dev->dev;
+	struct brcmf_if *ifp;
+	int idx, i, ret;
+	u32 val;
+	u32 addr_table[ARPOL_MAX_ENTRIES] = {0};
+
+	/* Find out if the notification is meant for us */
+	for (idx = 0; idx < BRCMF_MAX_IFS; idx++) {
+		ifp = drvr->iflist[idx];
+		if (ifp && ifp->ndev == ndev)
+			break;
+		if (idx == BRCMF_MAX_IFS - 1)
+			return NOTIFY_DONE;
+	}
+
+	/* check if arp offload is supported */
+	ret = brcmf_fil_iovar_int_get(ifp, "arpoe", &val);
+	if (ret)
+		return NOTIFY_OK;
+
+	/* old version only support primary index */
+	ret = brcmf_fil_iovar_int_get(ifp, "arp_version", &val);
+	if (ret)
+		val = 1;
+	if (val == 1)
+		ifp = drvr->iflist[0];
+
+	/* retrieve the table from firmware */
+	ret = brcmf_fil_iovar_data_get(ifp, "arp_hostip", addr_table,
+				       sizeof(addr_table));
+	if (ret) {
+		brcmf_err("fail to get arp ip table err:%d\n", ret);
+		return NOTIFY_OK;
+	}
+
+	for (i = 0; i < ARPOL_MAX_ENTRIES; i++)
+		if (ifa->ifa_address == addr_table[i])
+			break;
+
+	switch (action) {
+	case NETDEV_UP:
+		if (i == ARPOL_MAX_ENTRIES) {
+			brcmf_dbg(TRACE, "add %pI4 to arp table\n",
+				  &ifa->ifa_address);
+			/* set it directly */
+			ret = brcmf_fil_iovar_int_set(ifp, "arp_hostip",
+						      ifa->ifa_address);
+			if (ret)
+				brcmf_err("add arp ip err %d\n", ret);
+		}
+		break;
+	case NETDEV_DOWN:
+		if (i < ARPOL_MAX_ENTRIES) {
+			addr_table[i] = 0;
+			brcmf_dbg(TRACE, "remove %pI4 from arp table\n",
+				  &ifa->ifa_address);
+			/* clear the table in firmware */
+			ret = brcmf_fil_iovar_data_set(ifp, "arp_hostip_clear",
+						       NULL, 0);
+			if (ret) {
+				brcmf_err("fail to clear arp ip table err:%d\n",
+					  ret);
+				return NOTIFY_OK;
+			}
+			for (i = 0; i < ARPOL_MAX_ENTRIES; i++) {
+				if (addr_table[i] != 0) {
+					brcmf_fil_iovar_int_set(ifp,
+								"arp_hostip",
+								addr_table[i]);
+					if (ret)
+						brcmf_err("add arp ip err %d\n",
+							  ret);
+				}
+			}
+		}
+		break;
+	default:
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+#endif
+
  int brcmf_attach(struct device *dev)
  {
  	struct brcmf_pub *drvr = NULL;
@@ -1068,6 +1163,15 @@ int brcmf_bus_start(struct device *dev)
  		if (p2p_ifp)
  			ret = brcmf_net_p2p_attach(p2p_ifp);
  	}
+
+	if (ret)
+		goto fail;
+
+#ifdef CONFIG_INET
+	drvr->inetaddr_notifier.notifier_call = brcmf_inetaddr_changed;
+	ret = register_inetaddr_notifier(&drvr->inetaddr_notifier);
+#endif
+
  fail:
  	if (ret < 0) {
  		brcmf_err("failed: %d\n", ret);
@@ -1133,6 +1237,10 @@ void brcmf_detach(struct device *dev)
  	if (drvr == NULL)
  		return;
 
+#ifdef CONFIG_INET
+	unregister_inetaddr_notifier(&drvr->inetaddr_notifier);
+#endif
+
  	/* stop firmware event handling */
  	brcmf_fweh_detach(drvr);
  	if (drvr->config)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h +2 -0
index 77d8239..6018af7 100644
@@ -141,6 +141,8 @@ struct brcmf_pub {
  #ifdef DEBUG
  	struct dentry *dbgfs_dir;
  #endif
+
+	struct notifier_block inetaddr_notifier;
  };
 
  /* forward declarations */
#19 lore raw

Re: [PATCH V2 13/13] brcmfmac: add arp offload ip address table configuration support

Quoted 9 lines · Arend van Spriel
Quoted 4 lines · Arend van Spriel

From: Franky Lin <[email protected]>

Obtain ipv4 address through inetaddr notification for ARP offload host ip table configuration.

Turns out this patch has a sparse warning, ie. would not work on big-endian system. We have a fix for that. Should I mark this patch as dropped in patchwork?

Yeah, that's the best way. For example you could use state "Changes Requested" and then it automatically gets dropped from my queue.

Signature · 1 line
Kalle Valo
#20 lore raw

Re: [PATCH V2 13/13] brcmfmac: add arp offload ip address table configuration support

Quoted 8 lines · Kalle Valo
Quoted 6 lines · Arend van Spriel
Quoted 4 lines · Arend van Spriel

From: Franky Lin <[email protected]>

Obtain ipv4 address through inetaddr notification for ARP offload host ip table configuration.

Quoted 6 lines
Quoted 3 lines

Turns out this patch has a sparse warning, ie. would not work on big-endian system. We have a fix for that. Should I mark this patch as dropped in patchwork?

Yeah, that's the best way. For example you could use state "Changes Requested" and then it automatically gets dropped from my queue.

will do that.

Thanks,
Arend