usb: host: ehci-msm: Allow LS devices to work

index c23e285..aed499d 100644
@@ -61,6 +61,8 @@ static int ehci_msm_reset(struct usb_hcd *hcd)
 	writel(0x8, USB_AHBMODE);
 	/* Disable streaming mode and select host mode */
 	writel(0x13, USB_USBMODE);
+	/* Disable ULPI_TX_PKT_EN_CLR_FIX which is valid only for HSIC */
+	writel(readl(USB_GENCONFIG_2) & ~ULPI_TX_PKT_EN_CLR_FIX, USB_GENCONFIG_2);
 
 	return 0;
 }

index e159b39..974c379 100644
@@ -22,6 +22,7 @@
 #define USB_AHBBURST         (MSM_USB_BASE + 0x0090)
 #define USB_AHBMODE          (MSM_USB_BASE + 0x0098)
 #define USB_GENCONFIG_2      (MSM_USB_BASE + 0x00a0)
+#define ULPI_TX_PKT_EN_CLR_FIX	BIT(19)
 
 #define USB_CAPLENGTH        (MSM_USB_BASE + 0x0100) /* 8 bit */
 

index e1004bc..102837e 100644
@@ -33,6 +33,7 @@
 #include <linux/usb/msm_hsusb_hw.h>
 #include <linux/usb.h>
 #include <linux/usb/hcd.h>
+#include <linux/acpi.h>
 
 #include "ehci.h"
 

@@ -202,6 +203,12 @@ static const struct dev_pm_ops ehci_msm_dev_pm_ops = {
 	.resume          = ehci_msm_pm_resume,
 };
 
+static const struct acpi_device_id msm_ehci_acpi_ids[] = {
+	{ "QCOM8040", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, msm_ehci_acpi_ids);
+
 static const struct of_device_id msm_ehci_dt_match[] = {
 	{ .compatible = "qcom,ehci-host", },
 	{}

@@ -215,6 +222,7 @@ static struct platform_driver ehci_msm_driver = {
 		   .name = "msm_hsusb_host",
 		   .pm = &ehci_msm_dev_pm_ops,
 		   .of_match_table = msm_ehci_dt_match,
+		   .acpi_match_table = ACPI_PTR(msm_ehci_acpi_ids),
 	},
 };
 

index 102837e..b71947d 100644
@@ -56,6 +56,8 @@ static int ehci_msm_reset(struct usb_hcd *hcd)
 	if (retval)
 		return retval;
 
+	/* select ULPI phy and clear other status/control bits in PORTSC */
+	writel(PORTSC_PTS_ULPI, USB_PORTSC);
 	/* bursts of unspecified length. */
 	writel(0, USB_AHBBURST);
 	/* Use the AHB transactor, allow posted data writes */

index aed499d..e1004bc 100644
@@ -106,9 +106,9 @@ static int ehci_msm_probe(struct platform_device *pdev)
 	}
 
 	/*
-	 * OTG driver takes care of PHY initialization, clock management,
-	 * powering up VBUS, mapping of registers address space and power
-	 * management.
+	 * If there is an OTG driver, let it take care of PHY initialization,
+	 * clock management, powering up VBUS, mapping of registers address
+	 * space and power management.
 	 */
 	if (pdev->dev.of_node)
 		phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0);

@@ -116,27 +116,35 @@ static int ehci_msm_probe(struct platform_device *pdev)
 		phy = devm_usb_get_phy(&pdev->dev, USB_PHY_TYPE_USB2);
 
 	if (IS_ERR(phy)) {
-		dev_err(&pdev->dev, "unable to find transceiver\n");
-		ret = -EPROBE_DEFER;
-		goto put_hcd;
-	}
-
-	ret = otg_set_host(phy->otg, &hcd->self);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "unable to register with transceiver\n");
-		goto put_hcd;
+		if (PTR_ERR(phy) == -EPROBE_DEFER) {
+			dev_err(&pdev->dev, "unable to find transceiver\n");
+			ret = -EPROBE_DEFER;
+			goto put_hcd;
+		}
+		phy = NULL;
 	}
 
 	hcd->usb_phy = phy;
 	device_init_wakeup(&pdev->dev, 1);
-	/*
-	 * OTG device parent of HCD takes care of putting
-	 * hardware into low power mode.
-	 */
-	pm_runtime_no_callbacks(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
 
-	/* FIXME: need to call usb_add_hcd() here? */
+	if (phy && phy->otg) {
+		/*
+		 * MSM OTG driver takes care of adding the HCD and
+		 * placing hardware into low power mode via runtime PM.
+		 */
+		ret = otg_set_host(phy->otg, &hcd->self);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "unable to register with transceiver\n");
+			goto put_hcd;
+		}
+
+		pm_runtime_no_callbacks(&pdev->dev);
+		pm_runtime_enable(&pdev->dev);
+	} else {
+		ret = usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
+		if (ret)
+			goto put_hcd;
+	}
 
 	return 0;
 

@@ -154,9 +162,10 @@ static int ehci_msm_remove(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_set_suspended(&pdev->dev);
 
-	otg_set_host(hcd->usb_phy->otg, NULL);
-
-	/* FIXME: need to call usb_remove_hcd() here? */
+	if (hcd->usb_phy && hcd->usb_phy->otg)
+		otg_set_host(hcd->usb_phy->otg, NULL);
+	else
+		usb_remove_hcd(hcd);
 
 	usb_put_hcd(hcd);
 

index b71947d..3e226ef 100644
@@ -220,6 +220,7 @@ MODULE_DEVICE_TABLE(of, msm_ehci_dt_match);
 static struct platform_driver ehci_msm_driver = {
 	.probe	= ehci_msm_probe,
 	.remove	= ehci_msm_remove,
+	.shutdown = usb_hcd_platform_shutdown,
 	.driver = {
 		   .name = "msm_hsusb_host",
 		   .pm = &ehci_msm_dev_pm_ops,