ARM: OMAP2+: dts: cm-t335: initial support

[uri.mashiach at compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration]

---
 .../devicetree/bindings/arm/omap/omap.txt          |  3 ++
 arch/arm/boot/dts/Makefile                         |  7 +--
 arch/arm/boot/dts/am335x-cm-t335.dts               | 62 ++++++++++++++++++++++
 3 files changed, 69 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 9f4e513..2154f97 100644
@@ -138,6 +138,9 @@ Boards:
 - AM335X phyBOARD-WEGA: Single Board Computer dev kit
   compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"
 
+- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
+  compatible = "compulab,cm-t335", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +4 -3

index bb8fa02..0e011dc 100644
@@ -446,13 +446,14 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-base0033.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
-	am335x-sl50.dtb \
+	am335x-chiliboard.dtb \
+	am335x-cm-t335.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
+	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
-	am335x-lxm.dtb \
-	am335x-chiliboard.dtb \
+	am335x-sl50.dtb \
 	am335x-wega-rdk.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-duovero-parlor.dtb \

arch/arm/boot/dts/am335x-cm-t335.dts new file +62 -0

62 lines not on this page · raw message

Signature · 1 line

2.6.0

Uri Mashiach

author

2015-11-11 17:32 UTC #2 lore raw

PATCH 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

Gentle ping

Quoted 135 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.

Current patch adds support:
UART0 and GPIO LED

Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

[uri.mashiach at compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration]

---
  .../devicetree/bindings/arm/omap/omap.txt          |  3 ++
  arch/arm/boot/dts/Makefile                         |  7 +--
  arch/arm/boot/dts/am335x-cm-t335.dts               | 62 ++++++++++++++++++++++
  3 files changed, 69 insertions(+), 3 deletions(-)

create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 9f4e513..2154f97 100644
@@ -138,6 +138,9 @@ Boards:
  - AM335X phyBOARD-WEGA: Single Board Computer dev kit
    compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"
 
+- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
+  compatible = "compulab,cm-t335", "ti,am33xx"
+
  - OMAP5 EVM : Evaluation Module
    compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +4 -3

index bb8fa02..0e011dc 100644
@@ -446,13 +446,14 @@ dtb-$(CONFIG_SOC_AM33XX) += \
  	am335x-base0033.dtb \
  	am335x-bone.dtb \
  	am335x-boneblack.dtb \
-	am335x-sl50.dtb \
+	am335x-chiliboard.dtb \
+	am335x-cm-t335.dtb \
  	am335x-evm.dtb \
  	am335x-evmsk.dtb \
+	am335x-lxm.dtb \
  	am335x-nano.dtb \
  	am335x-pepper.dtb \
-	am335x-lxm.dtb \
-	am335x-chiliboard.dtb \
+	am335x-sl50.dtb \
  	am335x-wega-rdk.dtb
  dtb-$(CONFIG_ARCH_OMAP4) += \
  	omap4-duovero-parlor.dtb \

arch/arm/boot/dts/am335x-cm-t335.dts new file +62 -0

new file mode 100644
index 0000000..197d5ce
@@ -0,0 +1,62 @@
+/*
+ * am335x-cm-t335.dts - Device Tree file for Compulab CM-T335
+ *
+ * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "CompuLab CM-T335";
+	compatible = "compulab,cm-t335", "ti,am33xx";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>;	/* 128 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_led_pins>;
+		led at 0 {
+			label = "cm_t335:green";
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;	/* gpio2_0 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+
+	gpio_led_pins: pinmux_gpio_led_pins {
+		pinctrl-single,pins = <
+			0x88 (PIN_OUTPUT | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			/* uart0_rxd.uart0_rxd */
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* uart0_txd.uart0_txd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+

Igor Grinberg

2015-11-13 10:19 UTC #3 lore raw

PATCH 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

Hi Uri,

Quoted 17 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>
Add basic support for CompuLab cm-t335 module based on AM335X SoC.
CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.
The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.
Current patch adds support:
UART0 and GPIO LED
Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

[...]

Quoted 6 lines

arch/arm/boot/dts/am335x-cm-t335.dts new file +0 -0
new file mode 100644
index 0000000..197d5ce
@@ -0,0 +1,62 @@

[...]

Quoted 6 lines

+&am33xx_pinmux {
arch/arm/boot/dts/am335x-cm-t335.dts new file +5 -0
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+
+	gpio_led_pins: pinmux_gpio_led_pins {
+		pinctrl-single,pins = <

arch/arm/boot/dts/am335x-cm-t335.dts line 51

Quoted 10 lines

arch/arm/boot/dts/am335x-cm-t335.dts new file +10 -0

+			0x88 (PIN_OUTPUT | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			/* uart0_rxd.uart0_rxd */
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* uart0_txd.uart0_txd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)

Can we use AM33XX_IOPAD macro here?
and may be other patches too?

[...]

Signature · 2 lines

Regards,
Igor.

Uri Mashiach

author

2015-10-27 12:14 UTC #4 lore raw

PATCH 2/6 ARM: OMAP2+: dts: cm-t335: add basic support for I2C

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for I2C0 and I2C1 pins. Add description for I2C0 bus, set clock frequency to 400kHz. Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 37 ++++++++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +37 -0

index 197d5ce..39df3d2 100644
@@ -37,6 +37,24 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <>;
 
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			/* i2c0_sda.i2c0_sda */
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* i2c0_scl.i2c0_scl */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			/* uart0_ctsn.i2c1_sda */
+			0x168 (PIN_INPUT_PULLUP | MUX_MODE2)
+			/* uart0_rtsn.i2c1_scl */
+			0x16c (PIN_INPUT_PULLUP | MUX_MODE2)
+		>;
+	};
+
 	gpio_led_pins: pinmux_gpio_led_pins {
 		pinctrl-single,pins = <
 			0x88 (PIN_OUTPUT | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */

@@ -60,3 +78,22 @@
 	status = "okay";
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	eeprom: 24c02 at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	ext_rtc: em3027 at 56 {
+		compatible = "emmicro,em3027";
+		reg = <0x56>;
+	};
+};
+

Signature · 1 line

2.6.0

Uri Mashiach

author

2015-11-11 17:32 UTC #5 lore raw

PATCH 2/6 ARM: OMAP2+: dts: cm-t335: add basic support for I2C

Gentle ping

Quoted 66 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for I2C0 and I2C1 pins. Add description for I2C0 bus, set clock frequency to 400kHz. Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.

---
  arch/arm/boot/dts/am335x-cm-t335.dts | 37 ++++++++++++++++++++++++++++++++++++
  1 file changed, 37 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +37 -0

index 197d5ce..39df3d2 100644
@@ -37,6 +37,24 @@
  	pinctrl-names = "default";
  	pinctrl-0 = <>;
 
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			/* i2c0_sda.i2c0_sda */
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* i2c0_scl.i2c0_scl */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			/* uart0_ctsn.i2c1_sda */
+			0x168 (PIN_INPUT_PULLUP | MUX_MODE2)
+			/* uart0_rtsn.i2c1_scl */
+			0x16c (PIN_INPUT_PULLUP | MUX_MODE2)
+		>;
+	};
+
  	gpio_led_pins: pinmux_gpio_led_pins {
  		pinctrl-single,pins = <
  			0x88 (PIN_OUTPUT | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */

@@ -60,3 +78,22 @@
  	status = "okay";
  };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	eeprom: 24c02 at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	ext_rtc: em3027 at 56 {
+		compatible = "emmicro,em3027";
+		reg = <0x56>;
+	};
+};
+

Uri Mashiach

author

2015-10-27 12:14 UTC #6 lore raw

PATCH 3/6 ARM: OMAP2+: dts: cm-t335: add support for NAND flash

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for NAND specific GPMC pins. Add description for GPMC controller. Add child node for NAND flash including CM-T335 specific partition table to GPMC node. Enable error-location module (ELM).

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 106 +++++++++++++++++++++++++++++++++++
 1 file changed, 106 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +106 -0

index 39df3d2..9d6117a 100644
@@ -61,6 +61,41 @@
 		>;
 	};
 
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			/* gpmc_ad0.gpmc_ad0 */
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad1.gpmc_ad1 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad2.gpmc_ad2 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad3.gpmc_ad3 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad4.gpmc_ad4 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad5.gpmc_ad5 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad6.gpmc_ad6 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad7.gpmc_ad7 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wait0.gpmc_wait0 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wpn.gpio0_30 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)
+			/* gpmc_csn0.gpmc_csn0  */
+			0x7c (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_advn_ale.gpmc_advn_ale */
+			0x90 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_oen_ren.gpmc_oen_ren */
+			0x94 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_wen.gpmc_wen */
+			0x98 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_be0n_cle.gpmc_be0n_cle */
+			0x9c (PIN_OUTPUT | MUX_MODE0)
+		>;
+	};
+
 	uart0_pins: pinmux_uart0_pins {
 		pinctrl-single,pins = <
 			/* uart0_rxd.uart0_rxd */

@@ -97,3 +132,74 @@
 	};
 };
 
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand at 0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition at 0 {
+			label = "spl";
+			reg = <0x00000000 0x00200000>;
+		};
+		partition at 1 {
+			label = "uboot";
+			reg = <0x00200000 0x00100000>;
+		};
+		partition at 2 {
+			label = "uboot environment";
+			reg = <0x00300000 0x00100000>;
+		};
+		partition at 3 {
+			label = "dtb";
+			reg = <0x00400000 0x00100000>;
+		};
+		partition at 4 {
+			label = "splash";
+			reg = <0x00500000 0x00400000>;
+		};
+		partition at 5 {
+			label = "linux";
+			reg = <0x00900000 0x00600000>;
+		};
+		partition at 6 {
+			label = "rootfs";
+			reg = <0x00F00000 0>;
+		};
+	};
+};
+
+&elm {
+	status = "okay";
+};
+

Signature · 1 line

2.6.0

Uri Mashiach

author

2015-11-11 17:32 UTC #7 lore raw

PATCH 3/6 ARM: OMAP2+: dts: cm-t335: add support for NAND flash

Gentle ping

Quoted 136 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

---
  arch/arm/boot/dts/am335x-cm-t335.dts | 106 +++++++++++++++++++++++++++++++++++
  1 file changed, 106 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +106 -0

index 39df3d2..9d6117a 100644
@@ -61,6 +61,41 @@
  		>;
  	};
 
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			/* gpmc_ad0.gpmc_ad0 */
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad1.gpmc_ad1 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad2.gpmc_ad2 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad3.gpmc_ad3 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad4.gpmc_ad4 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad5.gpmc_ad5 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad6.gpmc_ad6 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad7.gpmc_ad7 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wait0.gpmc_wait0 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wpn.gpio0_30 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)
+			/* gpmc_csn0.gpmc_csn0  */
+			0x7c (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_advn_ale.gpmc_advn_ale */
+			0x90 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_oen_ren.gpmc_oen_ren */
+			0x94 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_wen.gpmc_wen */
+			0x98 (PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_be0n_cle.gpmc_be0n_cle */
+			0x9c (PIN_OUTPUT | MUX_MODE0)
+		>;
+	};
+
  	uart0_pins: pinmux_uart0_pins {
  		pinctrl-single,pins = <
  			/* uart0_rxd.uart0_rxd */

@@ -97,3 +132,74 @@
  	};
  };
 
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand at 0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition at 0 {
+			label = "spl";
+			reg = <0x00000000 0x00200000>;
+		};
+		partition at 1 {
+			label = "uboot";
+			reg = <0x00200000 0x00100000>;
+		};
+		partition at 2 {
+			label = "uboot environment";
+			reg = <0x00300000 0x00100000>;
+		};
+		partition at 3 {
+			label = "dtb";
+			reg = <0x00400000 0x00100000>;
+		};
+		partition at 4 {
+			label = "splash";
+			reg = <0x00500000 0x00400000>;
+		};
+		partition at 5 {
+			label = "linux";
+			reg = <0x00900000 0x00600000>;
+		};
+		partition at 6 {
+			label = "rootfs";
+			reg = <0x00F00000 0>;
+		};
+	};
+};
+
+&elm {
+	status = "okay";
+};
+

Uri Mashiach

author

2015-10-27 12:14 UTC #8 lore raw

PATCH 4/6 ARM: OMAP2+: dts: cm-t335: add support for MMC

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for MMC0 pins. Add fixed regulator 'vmmc_fixed'.
Enable MMC0 in 4-bit mode.

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +33 -0

index 9d6117a..976c330 100644
@@ -31,6 +31,14 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	/* regulator for mmc */
+	vmmc_fixed: fixedregulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &am33xx_pinmux {

@@ -104,6 +112,23 @@
 			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 		>;
 	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			/* mmc0_dat3.mmc0_dat3 */
+			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat2.mmc0_dat2 */
+			0xf4 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat1.mmc0_dat1 */
+			0xf8 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat0.mmc0_dat0 */
+			0xfc (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_clk.mmc0_clk */
+			0x100 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_cmd.mmc0_cmd */
+			0x104 (PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
 };
 
 &uart0 {

@@ -203,3 +228,11 @@
 	status = "okay";
 };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+

Signature · 1 line

2.6.0

Uri Mashiach

author

2015-11-11 17:33 UTC #9 lore raw

PATCH 4/6 ARM: OMAP2+: dts: cm-t335: add support for MMC

Gentle ping

Quoted 69 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for MMC0 pins. Add fixed regulator 'vmmc_fixed'.
Enable MMC0 in 4-bit mode.

---
  arch/arm/boot/dts/am335x-cm-t335.dts | 33 +++++++++++++++++++++++++++++++++
  1 file changed, 33 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +33 -0

index 9d6117a..976c330 100644
@@ -31,6 +31,14 @@
  			linux,default-trigger = "heartbeat";
  		};
  	};
+
+	/* regulator for mmc */
+	vmmc_fixed: fixedregulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
  };
 
  &am33xx_pinmux {

@@ -104,6 +112,23 @@
  			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)
  		>;
  	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			/* mmc0_dat3.mmc0_dat3 */
+			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat2.mmc0_dat2 */
+			0xf4 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat1.mmc0_dat1 */
+			0xf8 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat0.mmc0_dat0 */
+			0xfc (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_clk.mmc0_clk */
+			0x100 (PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_cmd.mmc0_cmd */
+			0x104 (PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
  };
 
  &uart0 {

@@ -203,3 +228,11 @@
  	status = "okay";
  };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+

Uri Mashiach

author

2015-10-27 12:14 UTC #10 lore raw

PATCH 5/6 ARM: OMAP2+: dts: cm-t335: add support for network device

From: Ilya Ledvich <[email protected]>

Add pinmux configurations for RGMII1 based CPSW Ethernet pins and MDIO pins:
- default configuration required for module in active state,
- sleep configuration required for module in inactive state.
Add mac node with single slave device. Add nodes for davinci_mdio and cpsw_emac0.

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 85 ++++++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +85 -0

index 976c330..0296d3f 100644
@@ -113,6 +113,71 @@
 		>;
 	};
 
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			/* mii1_txen.rgmii1_tctl */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxdv.rgmii1_rctl */
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd3.rgmii1_td3 */
+			0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd2.rgmii1_td2 */
+			0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd1.rgmii1_td1 */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd0.rgmii1_td0 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txclk.rgmii1_tclk */
+			0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxclk.rgmii1_rclk */
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd3.rgmii1_rd3 */
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd2.rgmii1_rd2 */
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd1.rgmii1_rd1 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd0.rgmii1_rd0 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* mdio_data.mdio_data */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
+			/* mdio_clk.mdio_clk */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
 	mmc1_pins: pinmux_mmc1_pins {
 		pinctrl-single,pins = <
 			/* mmc0_dat3.mmc0_dat3 */

@@ -228,6 +293,26 @@
 	status = "okay";
 };
 
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	slaves = <1>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmc_fixed>;

Signature · 1 line

2.6.0

Mugunthan V N

2015-10-27 13:14 UTC #11 lore raw

PATCH 5/6 ARM: OMAP2+: dts: cm-t335: add support for network device

Quoted 9 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>
Add pinmux configurations for RGMII1 based CPSW Ethernet pins and MDIO pins:
- default configuration required for module in active state,
- sleep configuration required for module in inactive state.
Add mac node with single slave device. Add nodes for davinci_mdio and cpsw_emac0.

Quoted 3 lines

Acked-by Igor Grinberg <[email protected]>
Signed-off-by Ilya Ledvich <[email protected]>
Signed-off-by Uri Mashiach <[email protected]>

Acked-by Mugunthan V N <[email protected]>

Regards
Mugunthan V N

Uri Mashiach

author

2015-11-11 17:33 UTC #12 lore raw

PATCH 5/6 ARM: OMAP2+: dts: cm-t335: add support for network device

Gentle ping

Quoted 120 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

---
  arch/arm/boot/dts/am335x-cm-t335.dts | 85 ++++++++++++++++++++++++++++++++++++
  1 file changed, 85 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +85 -0

index 976c330..0296d3f 100644
@@ -113,6 +113,71 @@
  		>;
  	};
 
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			/* mii1_txen.rgmii1_tctl */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxdv.rgmii1_rctl */
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd3.rgmii1_td3 */
+			0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd2.rgmii1_td2 */
+			0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd1.rgmii1_td1 */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd0.rgmii1_td0 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txclk.rgmii1_tclk */
+			0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxclk.rgmii1_rclk */
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd3.rgmii1_rd3 */
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd2.rgmii1_rd2 */
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd1.rgmii1_rd1 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd0.rgmii1_rd0 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2)
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* mdio_data.mdio_data */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
+			/* mdio_clk.mdio_clk */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
  	mmc1_pins: pinmux_mmc1_pins {
  		pinctrl-single,pins = <
  			/* mmc0_dat3.mmc0_dat3 */

@@ -228,6 +293,26 @@
  	status = "okay";
  };
 
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	slaves = <1>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
  &mmc1 {
  	status = "okay";
  	vmmc-supply = <&vmmc_fixed>;

Uri Mashiach

author

2015-10-27 12:15 UTC #13 lore raw

PATCH 6/6 ARM: OMAP2+: dts: cm-t335: add support for PWM backlight

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for ECAP0 pin. Add node for PWM backlight device.
Use PWM output from ecap0 as backlight source.

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +24 -0

index 0296d3f..571a453 100644
@@ -39,6 +39,13 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &am33xx_pinmux {

@@ -113,6 +120,13 @@
 		>;
 	};
 
+	ecap0_pins: pinmux_ecap0_pins {
+		pinctrl-single,pins = <
+			/* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			0x164 0x0
+		>;
+	};
+
 	cpsw_default: cpsw_default {
 		pinctrl-single,pins = <
 			/* Slave 1 */

@@ -222,6 +236,16 @@
 	};
 };
 
+&epwmss0 {
+	status = "okay";
+
+	ecap0: ecap@48300100 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+	};
+};
+
 &gpmc {
 	status = "okay";
 	pinctrl-names = "default";

Signature · 1 line

2.6.0

Uri Mashiach

author

2015-11-11 17:33 UTC #14 lore raw

PATCH 6/6 ARM: OMAP2+: dts: cm-t335: add support for PWM backlight

Gentle ping

Quoted 63 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for ECAP0 pin. Add node for PWM backlight device.
Use PWM output from ecap0 as backlight source.

---
  arch/arm/boot/dts/am335x-cm-t335.dts | 24 ++++++++++++++++++++++++
  1 file changed, 24 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +24 -0

index 0296d3f..571a453 100644
@@ -39,6 +39,13 @@
  		regulator-min-microvolt = <3300000>;
  		regulator-max-microvolt = <3300000>;
  	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
  };
 
  &am33xx_pinmux {

@@ -113,6 +120,13 @@
  		>;
  	};
 
+	ecap0_pins: pinmux_ecap0_pins {
+		pinctrl-single,pins = <
+			/* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			0x164 0x0
+		>;
+	};
+
  	cpsw_default: cpsw_default {
  		pinctrl-single,pins = <
  			/* Slave 1 */

@@ -222,6 +236,16 @@
  	};
  };
 
+&epwmss0 {
+	status = "okay";
+
+	ecap0: ecap at 48300100 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+	};
+};
+
  &gpmc {
  	status = "okay";
  	pinctrl-names = "default";

Uri Mashiach

author

2015-11-11 17:32 UTC #15 lore raw

cover ARM: OMAP2+: dts: cm-t335: initial support

Gentle ping

Quoted 24 lines · Uri Mashiach

Add basic support for CompuLab cm-t335 module based on AM335X SoC.
CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.
The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.
Ilya Ledvich (6):
ARM: OMAP2+: dts: cm-t335: add initial support
ARM: OMAP2+: dts: cm-t335: add basic support for I2C
ARM: OMAP2+: dts: cm-t335: add support for NAND flash
ARM: OMAP2+: dts: cm-t335: add support for MMC
ARM: OMAP2+: dts: cm-t335: add support for network device
ARM: OMAP2+: dts: cm-t335: add support for PWM backlight
  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
  arch/arm/boot/dts/Makefile                         |   7 +-
  arch/arm/boot/dts/am335x-cm-t335.dts               | 347 +++++++++++++++++++++
  3 files changed, 354 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Tony Lindgren

2015-11-11 17:50 UTC #16 lore raw

cover ARM: OMAP2+: dts: cm-t335: initial support

Hi,

Quoted 1 line · Uri Mashiach

Gentle ping

Well the merge window is ongoing, and I'm not touching anything except fixes until they are all out of the way. And after that I'll start applying patches for v4.5 merge window, usually by -rc2 except when things go wrong and we have regressions with the mainline kernel like we did during v4.3-rc cycle.

So for fixes, it's always a good time to send them. The sooner we have fixes out of the way after each merge window, the sooner I'll start applying new features.

So for new features, between -rc1 and -rc4. We really want to have all the new code sit in Linux next for a few weeks before each merge window so in general I try to have things ready togo by -rc5 for most part and by -rc6 latest.

Regards,

Tony

Uri Mashiach

author

2015-11-24 14:02 UTC #17 lore raw

v2 cover ARM: OMAP2+: dts: cm-t335: initial support

Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.

[v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions ] Ilya Ledvich (6):
ARM: OMAP2+: dts: cm-t335: add initial support
ARM: OMAP2+: dts: cm-t335: add basic support for I2C
ARM: OMAP2+: dts: cm-t335: add support for NAND flash
ARM: OMAP2+: dts: cm-t335: add support for MMC
ARM: OMAP2+: dts: cm-t335: add support for network device
ARM: OMAP2+: dts: cm-t335: add support for PWM backlight

 .../devicetree/bindings/arm/omap/omap.txt          |   3 +
 arch/arm/boot/dts/Makefile                         |   7 +-
 arch/arm/boot/dts/am335x-cm-t335.dts               | 348 +++++++++++++++++++++
 3 files changed, 355 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-11-24 14:02 UTC #18 lore raw

PATCH v2 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

From: Ilya Ledvich <[email protected]>

Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.

Current patch adds support:
UART0 and GPIO LED

Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

[uri.mashiach at compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration]

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 .../devicetree/bindings/arm/omap/omap.txt          |  3 ++
 arch/arm/boot/dts/Makefile                         |  7 +--
 arch/arm/boot/dts/am335x-cm-t335.dts               | 63 ++++++++++++++++++++++
 3 files changed, 70 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 9f4e513..2154f97 100644
@@ -138,6 +138,9 @@ Boards:
 - AM335X phyBOARD-WEGA: Single Board Computer dev kit
   compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"
 
+- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
+  compatible = "compulab,cm-t335", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +4 -3

index bb8fa02..0e011dc 100644
@@ -446,13 +446,14 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-base0033.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
-	am335x-sl50.dtb \
+	am335x-chiliboard.dtb \
+	am335x-cm-t335.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
+	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
-	am335x-lxm.dtb \
-	am335x-chiliboard.dtb \
+	am335x-sl50.dtb \
 	am335x-wega-rdk.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-duovero-parlor.dtb \

arch/arm/boot/dts/am335x-cm-t335.dts new file +63 -0

63 lines not on this page · raw message

Signature · 1 line

2.5.0

Rob Herring

maintainer

2015-11-25 22:44 UTC #19 lore raw

PATCH v2 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

Quoted 18 lines · Uri Mashiach

From: Ilya Ledvich <[email protected]>
Add basic support for CompuLab cm-t335 module based on AM335X SoC.
CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip.
The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus.
Current patch adds support:
UART0 and GPIO LED
Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

Quoted 7 lines

Signed-off-by Ilya Ledvich <[email protected]>
[uri.mashiach at compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration]
Signed-off-by Uri Mashiach <[email protected]>
Acked-by Igor Grinberg <[email protected]>
---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

This macro is exactly the kind we should not be doing in DT files which are ones that expand to multiple cells. But not really much point in doing 1 board differently from the rest, so:

Acked-by Rob Herring <[email protected]>

Rob

Quoted 115 lines

 .../devicetree/bindings/arm/omap/omap.txt          |  3 ++
 arch/arm/boot/dts/Makefile                         |  7 +--
 arch/arm/boot/dts/am335x-cm-t335.dts               | 63 ++++++++++++++++++++++
 3 files changed, 70 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/boot/dts/am335x-cm-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 9f4e513..2154f97 100644
@@ -138,6 +138,9 @@ Boards:
 - AM335X phyBOARD-WEGA: Single Board Computer dev kit
   compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"
 
+- AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
+  compatible = "compulab,cm-t335", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +4 -3

index bb8fa02..0e011dc 100644
@@ -446,13 +446,14 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-base0033.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
-	am335x-sl50.dtb \
+	am335x-chiliboard.dtb \
+	am335x-cm-t335.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
+	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
-	am335x-lxm.dtb \
-	am335x-chiliboard.dtb \
+	am335x-sl50.dtb \
 	am335x-wega-rdk.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-duovero-parlor.dtb \

arch/arm/boot/dts/am335x-cm-t335.dts new file +63 -0

new file mode 100644
index 0000000..719658e
@@ -0,0 +1,63 @@
+/*
+ * am335x-cm-t335.dts - Device Tree file for Compulab CM-T335
+ *
+ * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "CompuLab CM-T335";
+	compatible = "compulab,cm-t335", "ti,am33xx";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>;	/* 128 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_led_pins>;
+		led at 0 {
+			label = "cm_t335:green";
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;	/* gpio2_0 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+
+	gpio_led_pins: pinmux_gpio_led_pins {
+		pinctrl-single,pins = <
+			/* gpmc_csn3.gpio2_0 */
+			AM33XX_IOPAD(0x888, PIN_OUTPUT | MUX_MODE7)
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* uart0_txd.uart0_txd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+

Signature · 1 line

2.5.0

Tony Lindgren

2015-11-30 19:51 UTC #20 lore raw

PATCH v2 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

Quoted 2 lines · Uri Mashiach

arch/arm/boot/dts/am335x-cm-t335.dts new file +0 -0

...

arch/arm/boot/dts/am335x-cm-t335.dts line 63

Quoted 7 lines

+&uart0 {
arch/arm/boot/dts/am335x-cm-t335.dts new file +6 -0
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+

FYI, the extra line break at the end of the file causes whitespace warnings when applying. And fixing that causes extra hassles with applying the other patches in the series as the patches won't apply.. So for the next time, you may want to check that ;)

Also, the subject line should be "ARM: dts: ..." for the dts changes so the git log loooks unified for all the ARM SoCs.

Anyways, I've fixed up those locally and applying into omap-for-v4.5/dt.

Regards,

Tony

Uri Mashiach

author

2015-12-02 10:44 UTC #21 lore raw

PATCH v2 1/6 ARM: OMAP2+: dts: cm-t335: add initial support

Hi Tony,

Quoted 5 lines · Tony Lindgren

Quoted 2 lines · Uri Mashiach
arch/arm/boot/dts/am335x-cm-t335.dts new file +0 -0
...

Quoted 12 lines

arch/arm/boot/dts/am335x-cm-t335.dts line 63
Quoted 7 lines
+&uart0 {
arch/arm/boot/dts/am335x-cm-t335.dts new file +6 -0
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
FYI, the extra line break at the end of the file causes whitespace warnings when applying. And fixing that causes extra hassles with applying the other patches in the series as the patches won't apply.. So for the next time, you may want to check that ;)

Yes, I will definitely do that.

Quoted 3 lines

Also, the subject line should be "ARM: dts: ..." for the dts changes so the git log loooks unified for all the ARM SoCs.

Got it. Thanks!

Quoted 3 lines

Anyways, I've fixed up those locally and applying into omap-for-v4.5/dt.

Thank you Tony!

Signature · 2 lines

Regards,
Uri.

Uri Mashiach

author

2015-11-24 14:02 UTC #22 lore raw

PATCH v2 2/6 ARM: OMAP2+: dts: cm-t335: add basic support for I2C

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for I2C0 and I2C1 pins. Add description for I2C0 bus, set clock frequency to 400kHz. Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 arch/arm/boot/dts/am335x-cm-t335.dts | 37 ++++++++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +37 -0

index 719658e..02b6679 100644
@@ -37,6 +37,24 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <>;
 
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			/* i2c0_sda.i2c0_sda */
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* i2c0_scl.i2c0_scl */
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			/* uart0_ctsn.i2c1_sda */
+			AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE2)
+			/* uart0_rtsn.i2c1_scl */
+			AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2)
+		>;
+	};
+
 	gpio_led_pins: pinmux_gpio_led_pins {
 		pinctrl-single,pins = <
 			/* gpmc_csn3.gpio2_0 */

@@ -61,3 +79,22 @@
 	status = "okay";
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+	/* CM-T335 board EEPROM */
+	eeprom: 24c02 at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+	/* Real Time Clock */
+	ext_rtc: em3027 at 56 {
+		compatible = "emmicro,em3027";
+		reg = <0x56>;
+	};
+};
+

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-11-24 14:02 UTC #23 lore raw

PATCH v2 3/6 ARM: OMAP2+: dts: cm-t335: add support for NAND flash

From: Ilya Ledvich <[email protected]>

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 arch/arm/boot/dts/am335x-cm-t335.dts | 106 +++++++++++++++++++++++++++++++++++
 1 file changed, 106 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +106 -0

index 02b6679..431b6dd 100644
@@ -62,6 +62,41 @@
 		>;
 	};
 
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			/* gpmc_ad0.gpmc_ad0 */
+			AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad1.gpmc_ad1 */
+			AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad2.gpmc_ad2 */
+			AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad3.gpmc_ad3 */
+			AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad4.gpmc_ad4 */
+			AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad5.gpmc_ad5 */
+			AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad6.gpmc_ad6 */
+			AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_ad7.gpmc_ad7 */
+			AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wait0.gpmc_wait0 */
+			AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* gpmc_wpn.gpio0_30 */
+			AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7)
+			/* gpmc_csn0.gpmc_csn0  */
+			AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_advn_ale.gpmc_advn_ale */
+			AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_oen_ren.gpmc_oen_ren */
+			AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_wen.gpmc_wen */
+			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0)
+			/* gpmc_ben0_cle.gpmc_ben0_cle */
+			AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0)
+		>;
+	};
+
 	uart0_pins: pinmux_uart0_pins {
 		pinctrl-single,pins = <
 			/* uart0_rxd.uart0_rxd */

@@ -98,3 +133,74 @@
 	};
 };
 
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand at 0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition at 0 {
+			label = "spl";
+			reg = <0x00000000 0x00200000>;
+		};
+		partition at 1 {
+			label = "uboot";
+			reg = <0x00200000 0x00100000>;
+		};
+		partition at 2 {
+			label = "uboot environment";
+			reg = <0x00300000 0x00100000>;
+		};
+		partition at 3 {
+			label = "dtb";
+			reg = <0x00400000 0x00100000>;
+		};
+		partition at 4 {
+			label = "splash";
+			reg = <0x00500000 0x00400000>;
+		};
+		partition at 5 {
+			label = "linux";
+			reg = <0x00900000 0x00600000>;
+		};
+		partition at 6 {
+			label = "rootfs";
+			reg = <0x00F00000 0>;
+		};
+	};
+};
+
+&elm {
+	status = "okay";
+};
+

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-11-24 14:02 UTC #24 lore raw

PATCH v2 4/6 ARM: OMAP2+: dts: cm-t335: add support for MMC

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for MMC0 pins.
Add fixed regulator 'vmmc_fixed'.
Enable MMC0 in 4-bit mode.

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 arch/arm/boot/dts/am335x-cm-t335.dts | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +33 -0

index 431b6dd..0a20256 100644
@@ -31,6 +31,14 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	/* regulator for mmc */
+	vmmc_fixed: fixedregulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &am33xx_pinmux {

@@ -105,6 +113,23 @@
 			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 		>;
 	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			/* mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_clk.mmc0_clk */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
 };
 
 &uart0 {

@@ -204,3 +229,11 @@
 	status = "okay";
 };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-11-24 14:02 UTC #25 lore raw

PATCH v2 5/6 ARM: OMAP2+: dts: cm-t335: add support for network device

From: Ilya Ledvich <[email protected]>

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 arch/arm/boot/dts/am335x-cm-t335.dts | 85 ++++++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +85 -0

index 0a20256..9be0bfe 100644
@@ -114,6 +114,71 @@
 		>;
 	};
 
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			/* mii1_tx_en.rgmii1_tctl */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxdv.rgmii1_rctl */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd3.rgmii1_td3 */
+			AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd2.rgmii1_td2 */
+			AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd1.rgmii1_td1 */
+			AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txd0.rgmii1_td0 */
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_txclk.rgmii1_tclk */
+			AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxclk.rgmii1_rclk */
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd3.rgmii1_rd3 */
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd2.rgmii1_rd2 */
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd1.rgmii1_rd1 */
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2)
+			/* mii1_rxd0.rgmii1_rd0 */
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2)
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* mdio_data.mdio_data */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
+			/* mdio_clk.mdio_clk */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
 	mmc1_pins: pinmux_mmc1_pins {
 		pinctrl-single,pins = <
 			/* mmc0_dat3.mmc0_dat3 */

@@ -229,6 +294,26 @@
 	status = "okay";
 };
 
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	slaves = <1>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii-txid";
+};
+
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmc_fixed>;

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-11-24 14:02 UTC #26 lore raw

PATCH v2 6/6 ARM: OMAP2+: dts: cm-t335: add support for PWM backlight

From: Ilya Ledvich <[email protected]>

Add pinmux configuration for ECAP0 pin.
Add node for PWM backlight device.
Use PWM output from ecap0 as backlight source.

---
v1 -> v2: integrate AM33XX_IOPAD macro in pinmux definitions

 arch/arm/boot/dts/am335x-cm-t335.dts | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +24 -0

index 9be0bfe..4939d82 100644
@@ -39,6 +39,13 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &am33xx_pinmux {

@@ -114,6 +121,13 @@
 		>;
 	};
 
+	ecap0_pins: pinmux_ecap0_pins {
+		pinctrl-single,pins = <
+			/* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			AM33XX_IOPAD(0x964, 0x0)
+		>;
+	};
+
 	cpsw_default: cpsw_default {
 		pinctrl-single,pins = <
 			/* Slave 1 */

@@ -223,6 +237,16 @@
 	};
 };
 
+&epwmss0 {
+	status = "okay";
+
+	ecap0: ecap@48300100 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+	};
+};
+
 &gpmc {
 	status = "okay";
 	pinctrl-names = "default";

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-12-13 08:55 UTC #27 lore raw

cover ARM: dts: cm-t335: add peripheral support

Add support for the following CM-T335 module peripherals:
USB, I2C controller, LCD/DVI, bluetooth

Ilya Ledvich (1):
ARM: dts: cm-t335: add support for USB0

Uri Mashiach (4):
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for bluetooth

 .../devicetree/bindings/arm/omap/omap.txt          |   3 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/am335x-cm-t335.dts               |  51 ++++-
 arch/arm/boot/dts/am335x-sbc-t335.dts              | 219 +++++++++++++++++++++
 4 files changed, 273 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/am335x-sbc-t335.dts

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-12-13 08:55 UTC #28 lore raw

PATCH 1/5 ARM: dts: cm-t335: add support for USB0

From: Ilya Ledvich <[email protected]>

Enable USB0.

---
 arch/arm/boot/dts/am335x-cm-t335.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

arch/arm/boot/dts/am335x-cm-t335.dts +20 -0

index 31ff1aa..ae2366e 100644
@@ -237,6 +237,26 @@
 	};
 };
 
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
 &epwmss0 {
 	status = "okay";

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-12-13 08:55 UTC #29 lore raw

PATCH 2/5 ARM: dts: cm-t335: add support for SBC-T335

Add basic support for the SBC-T335.

CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354 SoC.

---
 Documentation/devicetree/bindings/arm/omap/omap.txt |  3 +++
 arch/arm/boot/dts/Makefile                          |  1 +
 arch/arm/boot/dts/am335x-sbc-t335.dts               | 16 ++++++++++++++++
 3 files changed, 20 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-sbc-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 2154f97..358e87e 100644
@@ -141,6 +141,9 @@ Boards:
 - AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
   compatible = "compulab,cm-t335", "ti,am33xx"
 
+- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
+  compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +1 -0

index 15411bc..d82ea97 100644
@@ -466,6 +466,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
+	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
 	am335x-wega-rdk.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \

arch/arm/boot/dts/am335x-sbc-t335.dts new file +16 -0

new file mode 100644
index 0000000..9e98445
@@ -0,0 +1,16 @@
+/*
+ * am335x-sbc-t335.dts - Device Tree file for Compulab SBC-T335
+ *
+ * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am335x-cm-t335.dts"
+
+/ {
+	model = "CompuLab CM-T335 on SB-T335";
+	compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx";
+};

Signature · 1 line

2.5.0

Rob Herring

maintainer

2015-12-14 01:25 UTC #30 lore raw

PATCH 2/5 ARM: dts: cm-t335: add support for SBC-T335

Quoted 8 lines · Uri Mashiach

Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354 SoC.
Signed-off-by Uri Mashiach <[email protected]>
Acked-by Igor Grinberg <[email protected]>

Acked-by Rob Herring <[email protected]>

Quoted 58 lines

---
 Documentation/devicetree/bindings/arm/omap/omap.txt |  3 +++
 arch/arm/boot/dts/Makefile                          |  1 +
 arch/arm/boot/dts/am335x-sbc-t335.dts               | 16 ++++++++++++++++
 3 files changed, 20 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-sbc-t335.dts

Documentation/devicetree/bindings/arm/omap/omap.txt +3 -0

index 2154f97..358e87e 100644
@@ -141,6 +141,9 @@ Boards:
 - AM335X CM-T335 : System On Module, built around the Sitara AM3352/4
   compatible = "compulab,cm-t335", "ti,am33xx"
 
+- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
+  compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"

arch/arm/boot/dts/Makefile +1 -0

index 15411bc..d82ea97 100644
@@ -466,6 +466,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
+	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
 	am335x-wega-rdk.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \

arch/arm/boot/dts/am335x-sbc-t335.dts new file +16 -0

new file mode 100644
index 0000000..9e98445
@@ -0,0 +1,16 @@
+/*
+ * am335x-sbc-t335.dts - Device Tree file for Compulab SBC-T335
+ *
+ * Copyright (C) 2014 - 2015 CompuLab Ltd. - http://www.compulab.co.il/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am335x-cm-t335.dts"
+
+/ {
+	model = "CompuLab CM-T335 on SB-T335";
+	compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx";
+};

Signature · 1 line

2.5.0

Tony Lindgren

2015-12-17 18:05 UTC #31 lore raw

PATCH 2/5 ARM: dts: cm-t335: add support for SBC-T335

Quoted 11 lines · Rob Herring

Quoted 8 lines · Uri Mashiach
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354 SoC.
Signed-off-by Uri Mashiach <[email protected]>
Acked-by Igor Grinberg <[email protected]>
Acked-by Rob Herring <[email protected]>

Thanks applying the whole series into omap-for-v4.5/dt.

Tony

Uri Mashiach

author

2015-12-13 08:55 UTC #32 lore raw

PATCH 3/5 ARM: dts: cm-t335: add support for I2C GPIO expander

The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.

---
 arch/arm/boot/dts/am335x-sbc-t335.dts | 11 +++++++++++
 1 file changed, 11 insertions(+)

arch/arm/boot/dts/am335x-sbc-t335.dts +11 -0

index 9e98445..4a5177e 100644
@@ -14,3 +14,14 @@
 	model = "CompuLab CM-T335 on SB-T335";
 	compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx";
 };
+
+&i2c0 {
+	/* GPIO extender */
+	gpio_ext: pca9555 at 26 {
+		compatible = "nxp,pca9555";
+		pinctrl-names = "default";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x26>;
+	};
+};

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-12-13 08:55 UTC #33 lore raw

PATCH 4/5 ARM: dts: cm-t335: add support for DVI/LCD

Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD. Add I2C GPIOs configurations for DVI and LCD enable.

---
 arch/arm/boot/dts/am335x-sbc-t335.dts | 192 ++++++++++++++++++++++++++++++++++
 1 file changed, 192 insertions(+)

arch/arm/boot/dts/am335x-sbc-t335.dts +192 -0

index 4a5177e..917d7cc 100644
@@ -13,6 +13,181 @@
 / {
 	model = "CompuLab CM-T335 on SB-T335";
 	compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx";
+
+	/* DRM display driver */
+	panel {
+		compatible = "ti,tilcdc,panel";
+		status = "okay";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&lcd_pins_default>;
+		pinctrl-1 = <&lcd_pins_sleep>;
+
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <32>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+		display-timings {
+			/* Timing selection performed by U-Boot */
+			timing0: lcd {/* 800x480p62 */
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <39>;
+				hback-porch = <39>;
+				hsync-len = <47>;
+				vback-porch = <29>;
+				vfront-porch = <13>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+			timing1: dvi { /* 1024x768p60 */
+				clock-frequency = <65000000>;
+				hactive = <1024>;
+				hfront-porch = <24>;
+				hback-porch = <160>;
+				hsync-len = <136>;
+				vactive = <768>;
+				vfront-porch = <3>;
+				vback-porch = <29>;
+				vsync-len = <6>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+			};
+		};
+	};
+};
+
+&am33xx_pinmux {
+	/* Display */
+	lcd_pins_default: lcd_pins_default {
+		pinctrl-single,pins = <
+			/* gpmc_ad8.lcd_data23 */
+			AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad9.lcd_data22 */
+			AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad10.lcd_data21 */
+			AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad11.lcd_data20 */
+			AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad12.lcd_data19 */
+			AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad13.lcd_data18 */
+			AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad14.lcd_data17 */
+			AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE1)
+			/* gpmc_ad15.lcd_data16 */
+			AM33XX_IOPAD(0x83c, PIN_OUTPUT | MUX_MODE1)
+			/* lcd_data0.lcd_data0 */
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data1.lcd_data1 */
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data2.lcd_data2 */
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data3.lcd_data3 */
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data4.lcd_data4 */
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data5.lcd_data5 */
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data6.lcd_data6 */
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data7.lcd_data7 */
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data8.lcd_data8 */
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data9.lcd_data9 */
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data10.lcd_data10 */
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data11.lcd_data11 */
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data12.lcd_data12 */
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data13.lcd_data13 */
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data14.lcd_data14 */
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_data15.lcd_data15 */
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_vsync.lcd_vsync */
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_hsync.lcd_hsync */
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_pclk.lcd_pclk */
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0)
+		>;
+	};
+
+	lcd_pins_sleep: lcd_pins_sleep {
+		pinctrl-single,pins = <
+			/* gpmc_ad8.lcd_data23 */
+			AM33XX_IOPAD(0x820, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad9.lcd_data22 */
+			AM33XX_IOPAD(0x824, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad10.lcd_data21 */
+			AM33XX_IOPAD(0x828, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad11.lcd_data20 */
+			AM33XX_IOPAD(0x82c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad12.lcd_data19 */
+			AM33XX_IOPAD(0x830, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad13.lcd_data18 */
+			AM33XX_IOPAD(0x834, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad14.lcd_data17 */
+			AM33XX_IOPAD(0x838, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* gpmc_ad15.lcd_data16 */
+			AM33XX_IOPAD(0x83c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* lcd_data0.lcd_data0 */
+			AM33XX_IOPAD(0x8a0, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data1.lcd_data1 */
+			AM33XX_IOPAD(0x8a4, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data2.lcd_data2 */
+			AM33XX_IOPAD(0x8a8, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data3.lcd_data3 */
+			AM33XX_IOPAD(0x8ac, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data4.lcd_data4 */
+			AM33XX_IOPAD(0x8b0, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data5.lcd_data5 */
+			AM33XX_IOPAD(0x8b4, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data6.lcd_data6 */
+			AM33XX_IOPAD(0x8b8, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data7.lcd_data7 */
+			AM33XX_IOPAD(0x8bc, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data8.lcd_data8 */
+			AM33XX_IOPAD(0x8c0, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data9.lcd_data9 */
+			AM33XX_IOPAD(0x8c4, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data10.lcd_data10 */
+			AM33XX_IOPAD(0x8c8, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data11.lcd_data11 */
+			AM33XX_IOPAD(0x8cc, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data12.lcd_data12 */
+			AM33XX_IOPAD(0x8d0, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data13.lcd_data13 */
+			AM33XX_IOPAD(0x8d4, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data14.lcd_data14 */
+			AM33XX_IOPAD(0x8d8, PULL_DISABLE | MUX_MODE7)
+			/* lcd_data15.lcd_data15 */
+			AM33XX_IOPAD(0x8dc, PULL_DISABLE | MUX_MODE7)
+			/* lcd_vsync.lcd_vsync */
+			AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* lcd_hsync.lcd_hsync */
+			AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* lcd_pclk.lcd_pclk */
+			AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
+			AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
 };
 
 &i2c0 {

@@ -23,5 +198,22 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reg = <0x26>;
+		dvi_ena {
+			gpio-hog;
+			gpios = <13 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "dvi-enable";
+		};
+		lcd_ena {
+			gpio-hog;
+			gpios = <11 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "lcd-enable";
+		};
 	};
 };
+
+/* Display */
+&lcdc {
+	status = "okay";
+};

Signature · 1 line

2.5.0

Uri Mashiach

author

2015-12-13 08:55 UTC #34 lore raw

PATCH 5/5 ARM: dts: cm-t335: add support for bluetooth

bluetooth HW is WLS1271 chip connected to UART1.

Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.

Bluetooth enable GPIO is set to enable during startup by setting the relevant pinmux pin to pull-up.