Skip to contentSkip to conversation

dm: x86: Convert ivybridge code to use driver model

PATCH New Simon Glass 3 participants 130 messages Jan 17, 2016 – Jan 21, 2016

Subsystems (7)
x86 USB Block layer PCI +3 more subsystems
lore
Share & tools
lore
#0 lore raw

v2 cover dm: x86: Convert ivybridge code to use driver model

At present ivybridge is the only x86 implementation that includes a reasonably full board init. This means there is a lot more code than with a board that uses FSP (even then we don't have memory init or graphics init code).

This code does not use proper drivers for the devices and so its use of driver model is limited. This series refactors the code to improve this. In particular it drops use of the old x86_pci_...() API in favour of dm_pci_...(). The latter requires that each PCI device has a driver.

A few very minor driver model improvements are added to support this. Also a Northbridge uclass is added - this could instead be done with the syscon, so comments are well as to which is best.

A small amount of additional work will be needed to remove use of the x86_pci_...() in arch/x86, but this series represents the bulk of it.

Changes in v2:
- Fix -EEPFNOSUPPORT typo
- Add missing of_match member init so that ehci_pci_ids[] is used
- Add missing 'given' word
- Drop unnecessary/incorrect non-DM code in dm_pci_run_vga_bios()
- Drop unused 'gen-dec' device tree property
- Drop the init() method in the PCH
- Rename this commit from 'x86: ivybridge: Set up the PCH init'
- Drop unnecessary DECLARE_GLOBAL_DATA_PTR
- Drop explicit PCH probe
- Drop LPC init method
- Rename patch from 'Add an init() method for the bd82x6x LPC'
- Update to drop LPC init method and use probe() instead
- Fix 'baords' typo in the commit message
- Add a comment as to why we are initing the devices again
- Drop northbridge_enable()
- Rename from 'Move northbridge setup to the northbridge driver'
- Drop this unnecessary init
- Rename the AHCI uclass to DISK
- Update to use the disk uclass
- Update to use the disk uclass
- Drop unnecessary IRQ and command register init
- Update to use LPC probe() method instead of init()
- Drop the special compatible string in chromebook_link.dts
- Expand the Kconfig help a little
- Avoid needing the pch device to set up the USB bar
- Fix incorrect bits in bridge_silicon_revision() comment
- Rename from 'Convert EHCI init to use the DM PCI API'
- Drop this init
- Fix the USB PCI address in the device tree
- Enable SYSCON and REGMAP for panther to avoid a build error
- Drop bd82x6x_pci_init() function and associated DM-conversion patch
- Drop LPC init method an 'Add an init() method to the LPC uclass' patch

Simon Glass (55):
dm: core: Display the error number when driver binding fails
dm: usb: Add a compatible string for PCI EHCI controller
dm: syscon: Allow finding devices by driver data
dm: pci: Convert bios_emu to use the driver model PCI API
x86: ivybridge: Set up the LPC device using driver model
x86: ivybridge: Move lpc_early_init() to probe()
x86: ivybridge: Move more init to the probe() function
x86: ivybridge: Rename bd82x6x_init()
dm: x86: Add a northbridge uclass
x86: ivybridge: Add a driver for the bd82x6x northbridge
x86: ivybridge: Move northbridge init into the probe() method
x86: ivybridge: Move LPC and PCH init into northbridge probe()
x86: ivybridge: Rename lpc_init() to lpc_init_extra()
x86: ivybridge: Probe the LPC in CPU init
x86: ivybridge: Move graphics init much later
x86: ivybridge: Move sandybridge init to the lpc probe() method
x86: ivybridge: Move GPIO init to the LPC init() method
x86: ivybridge: Use common CPU init code
x86: ivybridge: Move CPU init code into the driver
x86: ivybridge: Set up the thermal target correctly
x86: ivybridge: Drop the dead MTRR code
x86: ivybridge: Move early init code into northbridge.c
x86: Make x86_init_cpus() static
x86: Don't show an error when the MRC cache is up to date
x86: Bring up northbridge, pch and lpc after the CPUs
x86: ivybridge: Move northbridge and PCH init into drivers
x86: ivybridge: Use driver model PCI API in bd82x6x.c
x86: ivybridge: Drop unnecessary northbridge setup
ahci: Add a disk-controller uclass
x86: ivybridge: Do the SATA init before relocation
x86: ivybridge: Drop the unused bd82x6x_init_extra()
x86: ivybridge: Use the SATA driver to do the init
x86: ivybridge: Use driver model PCI API in sata.c
x86: ivybridge: Move lpc_enable() into gma.c
x86: ivybridge: Move LPC init into the LPC probe() method
x86: ivybridge: Drop the special PCI driver
x86: ivybridge: Convert lpc init code to DM PCI API
x86: Enable DM_USB for link and panther
x86: i2c: Add a stub driver for Intel I2C/SMbus
x86: ivybridge: Use the I2C driver to perform SMbus init
x86: ivybridge: Convert enable_usb_bar() to use DM PCI API
x86: ivybridge: Convert dram_init() to use DM PCI API
x86: ivybridge: Convert sdram_initialise() to use DM PCI API
x86: chromebook_link: Enable the syscon uclass
x86: ivybridge: Convert SDRAM init to use driver model
x86: ivybridge: Convert report_platform to DM PCI API
x86: ivybridge: Convert pch.c to use DM PCI API
x86: ivybridge: Move code from pch.c to bd82x6x.c
x86: ivybridge: Sort out the calls to bridge_silicon_revision()
x86: ivybridge: Drop special EHCI init
x86: ivybridge: Drop XHCI support
x86: ivybridge: Drop the SMM-locking code
x86: Set up a shared syscon numbering schema
x86: ivybridge: Use syscon for the GMA device
x86: fdt: Drop the unused compatible strings in fdtdec

 arch/x86/cpu/cpu.c                                |  22 +-
 arch/x86/cpu/ivybridge/Makefile                   |   5 -
 arch/x86/cpu/ivybridge/bd82x6x.c                  | 217 ++++++++++------
 arch/x86/cpu/ivybridge/cpu.c                      | 146 +++--------
 arch/x86/cpu/ivybridge/early_init.c               | 147 -----------
 arch/x86/cpu/ivybridge/early_me.c                 |  70 +++--
 arch/x86/cpu/ivybridge/gma.c                      | 114 ++++++--
 arch/x86/cpu/ivybridge/lpc.c                      | 301 ++++++++++++----------
 arch/x86/cpu/ivybridge/model_206ax.c              | 126 ++++-----
 arch/x86/cpu/ivybridge/northbridge.c              | 126 ++++++---
 arch/x86/cpu/ivybridge/pch.c                      | 123 ---------
 arch/x86/cpu/ivybridge/pci.c                      |  67 -----
 arch/x86/cpu/ivybridge/report_platform.c          |  11 +-
 arch/x86/cpu/ivybridge/sata.c                     | 132 ++++++----
 arch/x86/cpu/ivybridge/sdram.c                    |  64 +++--
 arch/x86/cpu/ivybridge/usb_ehci.c                 |  29 ---
 arch/x86/cpu/ivybridge/usb_xhci.c                 |  32 ---
 arch/x86/dts/chromebook_link.dts                  |  86 ++++++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h     |  23 +-
 arch/x86/include/asm/arch-ivybridge/me.h          |  45 +++-
 arch/x86/include/asm/arch-ivybridge/pch.h         |  27 +-
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  13 +-
 arch/x86/include/asm/cpu.h                        |  11 +
 arch/x86/include/asm/u-boot-x86.h                 |   2 -
 arch/x86/lib/Makefile                             |   1 +
 arch/x86/lib/mrccache.c                           |   6 +-
 arch/x86/lib/northbridge-uclass.c                 |  15 ++
 board/google/chromebook_link/link.c               |   8 -
 configs/chromebook_link_defconfig                 |   9 +
 configs/chromebox_panther_defconfig               |   4 +
 drivers/bios_emulator/atibios.c                   | 109 +++++++-
 drivers/bios_emulator/bios.c                      |  39 +++
 drivers/block/Kconfig                             |   9 +
 drivers/block/Makefile                            |   1 +
 drivers/block/disk-uclass.c                       |  14 +
 drivers/core/lists.c                              |   3 +-
 drivers/core/syscon-uclass.c                      |  31 ++-
 drivers/i2c/Kconfig                               |   9 +
 drivers/i2c/Makefile                              |   1 +
 drivers/i2c/intel_i2c.c                           |  75 ++++++
 drivers/pci/pci_rom.c                             |   6 +-
 drivers/usb/host/ehci-pci.c                       |   6 +
 include/bios_emul.h                               |  19 +-
 include/dm/uclass-id.h                            |   2 +
 include/fdtdec.h                                  |   5 -
 include/syscon.h                                  |  14 +
 lib/fdtdec.c                                      |   5 -
 test/dm/syscon.c                                  |  17 ++
 48 files changed, 1288 insertions(+), 1059 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/early_init.c
 delete mode 100644 arch/x86/cpu/ivybridge/pch.c
 delete mode 100644 arch/x86/cpu/ivybridge/pci.c
 delete mode 100644 arch/x86/cpu/ivybridge/usb_ehci.c
 delete mode 100644 arch/x86/cpu/ivybridge/usb_xhci.c
 create mode 100644 arch/x86/lib/northbridge-uclass.c
 create mode 100644 drivers/block/disk-uclass.c
 create mode 100644 drivers/i2c/intel_i2c.c
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#1 lore raw

PATCH v2 1/55 dm: core: Display the error number when driver binding fails

This is often -96 (-EPFNOSUPPORT) which indicates that the uclass is not compiled in. Display the error number to make this easier to spot.

---

Changes in v2:
- Fix -EEPFNOSUPPORT typo

 drivers/core/lists.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/core/lists.c +2 -1
index a1c9478..c4fc216 100644
@@ -172,7 +172,8 @@ int lists_bind_fdt(struct udevice *parent, const void *blob, int offset,
 		dm_dbg("   - found match at '%s'\n", entry->name);
 		ret = device_bind(parent, entry, name, NULL, offset, &dev);
 		if (ret) {
-			dm_warn("Error binding driver '%s'\n", entry->name);
+			dm_warn("Error binding driver '%s': %d\n", entry->name,
+				ret);
 			return ret;
 		} else {
 			dev->driver_data = id->data;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#2 lore raw

PATCH v2 1/55 dm: core: Display the error number when driver binding fails

Quoted 8 lines · Simon Glass

This is often -96 (-EPFNOSUPPORT) which indicates that the uclass is not compiled in. Display the error number to make this easier to spot.

---

applied to u-boot-x86/master, thanks!

#3 lore raw

PATCH v2 2/55 dm: usb: Add a compatible string for PCI EHCI controller

In reply to Simon Glass

Add a compatible string to allow this to be specified in the device tree if needed.

---

Changes in v2:
- Add missing of_match member init so that ehci_pci_ids[] is used

 drivers/usb/host/ehci-pci.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/usb/host/ehci-pci.c +6 -0
index cda1c6d..f21a1fa 100644
@@ -137,11 +137,17 @@ static int ehci_pci_remove(struct udevice *dev)
 	return 0;
 }
 
+static const struct udevice_id ehci_pci_ids[] = {
+	{ .compatible = "ehci-pci" },
+	{ }
+};
+
 U_BOOT_DRIVER(ehci_pci) = {
 	.name	= "ehci_pci",
 	.id	= UCLASS_USB,
 	.probe = ehci_pci_probe,
 	.remove = ehci_pci_remove,
+	.of_match = ehci_pci_ids,
 	.ops	= &ehci_usb_ops,
 	.platdata_auto_alloc_size = sizeof(struct usb_platdata),
 	.priv_auto_alloc_size = sizeof(struct ehci_pci_priv),
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#6 lore raw

PATCH v2 2/55 dm: usb: Add a compatible string for PCI EHCI controller

Quoted 7 lines · Bin Meng
Quoted 6 lines · Simon Glass

Add a compatible string to allow this to be specified in the device tree if needed.

---

Quoted 8 lines
Quoted 6 lines

Changes in v2:
- Add missing of_match member init so that ehci_pci_ids[] is used

 drivers/usb/host/ehci-pci.c | 6 ++++++
 1 file changed, 6 insertions(+)

applied to u-boot-x86/master, thanks!

#7 lore raw

PATCH v2 3/55 dm: syscon: Allow finding devices by driver data

In reply to Simon Glass

We have a way to find a regmap by its syscon driver data value. Add the same for syscon itself.

---

Changes in v2:
- Add missing 'given' word

 drivers/core/syscon-uclass.c | 31 +++++++++++++++++++------------
 include/syscon.h             | 14 ++++++++++++++
 test/dm/syscon.c             | 17 +++++++++++++++++
 3 files changed, 50 insertions(+), 12 deletions(-)
drivers/core/syscon-uclass.c +19 -12
index 686c320..a0666d0 100644
@@ -32,7 +32,7 @@ static int syscon_pre_probe(struct udevice *dev)
 	return regmap_init_mem(dev, &priv->regmap);
 }
 
-struct regmap *syscon_get_regmap_by_driver_data(ulong driver_data)
+int syscon_get_by_driver_data(ulong driver_data, struct udevice **devp)
 {
 	struct udevice *dev;
 	struct uclass *uc;
@@ -40,22 +40,29 @@ struct regmap *syscon_get_regmap_by_driver_data(ulong driver_data)
 
 	ret = uclass_get(UCLASS_SYSCON, &uc);
 	if (ret)
-		return ERR_PTR(ret);
+		return ret;
 	uclass_foreach_dev(dev, uc) {
 		if (dev->driver_data == driver_data) {
-			struct syscon_uc_info *priv;
-			int ret;
-
-			ret = device_probe(dev);
-			if (ret)
-				return ERR_PTR(ret);
-			priv = dev_get_uclass_priv(dev);
-
-			return priv->regmap;
+			*devp = dev;
+			return device_probe(dev);
 		}
 	}
 
-	return ERR_PTR(-ENODEV);
+	return -ENODEV;
+}
+
+struct regmap *syscon_get_regmap_by_driver_data(ulong driver_data)
+{
+	struct syscon_uc_info *priv;
+	struct udevice *dev;
+	int ret;
+
+	ret = syscon_get_by_driver_data(driver_data, &dev);
+	if (ret)
+		return ERR_PTR(ret);
+	priv = dev_get_uclass_priv(dev);
+
+	return priv->regmap;
 }
 
 void *syscon_get_first_range(ulong driver_data)
include/syscon.h +14 -0
index c62ccd6..4593b6e 100644
@@ -37,6 +37,20 @@ struct regmap *syscon_get_regmap(struct udevice *dev);
  *
  * Each system controller can be accessed by its driver data, which is
  * assumed to be unique through the scope of all system controllers that
+ * are in use. This function looks up the controller given this driver data.
+ *
+ * @driver_data:	Driver data value to look up
+ * @devp:		Returns the controller correponding to @driver_data
+ * @return 0 on success, -ENODEV if the ID was not found, or other -ve error
+ *	   code
+ */
+int syscon_get_by_driver_data(ulong driver_data, struct udevice **devp);
+
+/**
+ * syscon_get_regmap_by_driver_data() - Look up a controller by its ID
+ *
+ * Each system controller can be accessed by its driver data, which is
+ * assumed to be unique through the scope of all system controllers that
  * are in use. This function looks up the regmap given this driver data.
  *
  * @driver_data:	Driver data value to look up
test/dm/syscon.c +17 -0
index 3642481..c40f5fc 100644
@@ -29,3 +29,20 @@ static int dm_test_syscon_base(struct unit_test_state *uts)
 	return 0;
 }
 DM_TEST(dm_test_syscon_base, DM_TESTF_SCAN_PDATA | DM_TESTF_SCAN_FDT);
+
+/* Test system controller finding */
+static int dm_test_syscon_by_driver_data(struct unit_test_state *uts)
+{
+	struct udevice *dev;
+
+	ut_assertok(syscon_get_by_driver_data(SYSCON0, &dev));
+	ut_asserteq(SYSCON0, dev->driver_data);
+
+	ut_assertok(syscon_get_by_driver_data(SYSCON1, &dev));
+	ut_asserteq(SYSCON1, dev->driver_data);
+
+	ut_asserteq(-ENODEV, syscon_get_by_driver_data(2, &dev));
+
+	return 0;
+}
+DM_TEST(dm_test_syscon_by_driver_data, DM_TESTF_SCAN_PDATA | DM_TESTF_SCAN_FDT);
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#8 lore raw

PATCH v2 3/55 dm: syscon: Allow finding devices by driver data

Quoted 6 lines · Simon Glass

We have a way to find a regmap by its syscon driver data value. Add the same for syscon itself.

---

Quoted 8 lines

Changes in v2:
- Add missing 'given' word

 drivers/core/syscon-uclass.c | 31 +++++++++++++++++++------------
 include/syscon.h             | 14 ++++++++++++++
 test/dm/syscon.c             | 17 +++++++++++++++++
 3 files changed, 50 insertions(+), 12 deletions(-)
#9 lore raw

PATCH v2 3/55 dm: syscon: Allow finding devices by driver data

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

We have a way to find a regmap by its syscon driver data value. Add the same for syscon itself.

---

Changes in v2:
- Add missing 'given' word

Quoted 7 lines
Quoted 5 lines
 drivers/core/syscon-uclass.c | 31 +++++++++++++++++++------------
 include/syscon.h             | 14 ++++++++++++++
 test/dm/syscon.c             | 17 +++++++++++++++++
 3 files changed, 50 insertions(+), 12 deletions(-)

applied to u-boot-x86/master, thanks!

#10 lore raw

PATCH v2 4/55 dm: pci: Convert bios_emu to use the driver model PCI API

In reply to Simon Glass

At present this BIOS emulator uses a bus/device/function number. Change it to use a device if CONFIG_DM_PCI is enabled.

---

Changes in v2:
- Drop unnecessary/incorrect non-DM code in dm_pci_run_vga_bios()

 drivers/bios_emulator/atibios.c | 109 ++++++++++++++++++++++++++++++++++++++--
 drivers/bios_emulator/bios.c    |  39 ++++++++++++++
 drivers/pci/pci_rom.c           |   6 +--
 include/bios_emul.h             |  19 ++++++-
 4 files changed, 165 insertions(+), 8 deletions(-)
drivers/bios_emulator/atibios.c +105 -4
index dec6230..7717246 100644
@@ -226,11 +226,19 @@ This function executes the BIOS POST code on the controller. We assume that
 at this stage the controller has its I/O and memory space enabled and
 that all other controllers are in a disabled state.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+static void PCI_doBIOSPOST(struct udevice *pcidev, BE_VGAInfo *vga_info,
+			   int vesa_mode, struct vbe_mode_info *mode_info)
+#else
 static void PCI_doBIOSPOST(pci_dev_t pcidev, BE_VGAInfo *vga_info,
 			   int vesa_mode, struct vbe_mode_info *mode_info)
+#endif
 {
 	RMREGS regs;
 	RMSREGS sregs;
+#ifdef CONFIG_DM_PCI
+	pci_dev_t bdf;
+#endif
 
 	/* Determine the value to store in AX for BIOS POST. Per the PCI specs,
 	 AH must contain the bus and AL must contain the devfn, encoded as
@@ -238,9 +246,14 @@ static void PCI_doBIOSPOST(pci_dev_t pcidev, BE_VGAInfo *vga_info,
 	 */
 	memset(&regs, 0, sizeof(regs));
 	memset(&sregs, 0, sizeof(sregs));
+#ifdef CONFIG_DM_PCI
+	bdf = dm_pci_get_bdf(pcidev);
+	regs.x.ax = (int)PCI_BUS(bdf) << 8 |
+			(int)PCI_DEV(bdf) << 3 | (int)PCI_FUNC(bdf);
+#else
 	regs.x.ax = ((int)PCI_BUS(pcidev) << 8) |
 	    ((int)PCI_DEV(pcidev) << 3) | (int)PCI_FUNC(pcidev);
-
+#endif
 	/*Setup the X86 emulator for the VGA BIOS*/
 	BE_setVGA(vga_info);
 
@@ -281,15 +294,28 @@ NOTE: This function leaves the original memory aperture disabled by leaving
       it programmed to all 1's. It must be restored to the correct value
       later.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+static u32 PCI_findBIOSAddr(struct udevice *pcidev, int *bar)
+#else
 static u32 PCI_findBIOSAddr(pci_dev_t pcidev, int *bar)
+#endif
 {
 	u32 base, size;
 
 	for (*bar = 0x10; *bar <= 0x14; (*bar) += 4) {
+#ifdef CONFIG_DM_PCI
+		dm_pci_read_config32(pcidev, *bar, &base);
+#else
 		pci_read_config_dword(pcidev, *bar, &base);
+#endif
 		if (!(base & 0x1)) {
+#ifdef CONFIG_DM_PCI
+			dm_pci_write_config32(pcidev, *bar, 0xFFFFFFFF);
+			dm_pci_read_config32(pcidev, *bar, &size);
+#else
 			pci_write_config_dword(pcidev, *bar, 0xFFFFFFFF);
 			pci_read_config_dword(pcidev, *bar, &size);
+#endif
 			size = ~(size & ~0xFF) + 1;
 			if (size >= MAX_BIOSLEN)
 				return base & ~0xFF;
@@ -312,11 +338,19 @@ necessary).
 Anyway to fix this we change all I/O mapped base registers and
 chop off the top bits.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+static void PCI_fixupIObase(struct udevice *pcidev, int reg, u32 *base)
+#else
 static void PCI_fixupIObase(pci_dev_t pcidev, int reg, u32 * base)
+#endif
 {
 	if ((*base & 0x1) && (*base > 0xFFFE)) {
 		*base &= 0xFFFF;
+#ifdef CONFIG_DM_PCI
+		dm_pci_write_config32(pcidev, reg, *base);
+#else
 		pci_write_config_dword(pcidev, reg, *base);
+#endif
 
 	}
 }
@@ -331,18 +365,30 @@ Pointers to the mapped BIOS image
 REMARKS:
 Maps a pointer to the BIOS image on the graphics card on the PCI bus.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+void *PCI_mapBIOSImage(struct udevice *pcidev)
+#else
 void *PCI_mapBIOSImage(pci_dev_t pcidev)
+#endif
 {
 	u32 BIOSImageBus;
 	int BIOSImageBAR;
 	u8 *BIOSImage;
 
 	/*Save PCI BAR registers that might get changed*/
+#ifdef CONFIG_DM_PCI
+	dm_pci_read_config32(pcidev, PCI_ROM_ADDRESS, &saveROMBaseAddress);
+	dm_pci_read_config32(pcidev, PCI_BASE_ADDRESS_0, &saveBaseAddress10);
+	dm_pci_read_config32(pcidev, PCI_BASE_ADDRESS_1, &saveBaseAddress14);
+	dm_pci_read_config32(pcidev, PCI_BASE_ADDRESS_2, &saveBaseAddress18);
+	dm_pci_read_config32(pcidev, PCI_BASE_ADDRESS_4, &saveBaseAddress20);
+#else
 	pci_read_config_dword(pcidev, PCI_ROM_ADDRESS, &saveROMBaseAddress);
 	pci_read_config_dword(pcidev, PCI_BASE_ADDRESS_0, &saveBaseAddress10);
 	pci_read_config_dword(pcidev, PCI_BASE_ADDRESS_1, &saveBaseAddress14);
 	pci_read_config_dword(pcidev, PCI_BASE_ADDRESS_2, &saveBaseAddress18);
 	pci_read_config_dword(pcidev, PCI_BASE_ADDRESS_4, &saveBaseAddress20);
+#endif
 
 	/*Fix up I/O base registers to less than 64K */
 	if(saveBaseAddress14 != 0)
@@ -361,13 +407,21 @@ void *PCI_mapBIOSImage(pci_dev_t pcidev)
 		return NULL;
 	}
 
+#ifdef CONFIG_DM_PCI
+	BIOSImage = dm_pci_bus_to_virt(pcidev, BIOSImageBus,
+				       PCI_REGION_MEM, 0, MAP_NOCACHE);
+
+	/*Change the PCI BAR registers to map it onto the bus.*/
+	dm_pci_write_config32(pcidev, BIOSImageBAR, 0);
+	dm_pci_write_config32(pcidev, PCI_ROM_ADDRESS, BIOSImageBus | 0x1);
+#else
 	BIOSImage = pci_bus_to_virt(pcidev, BIOSImageBus,
 				    PCI_REGION_MEM, 0, MAP_NOCACHE);
 
 	/*Change the PCI BAR registers to map it onto the bus.*/
 	pci_write_config_dword(pcidev, BIOSImageBAR, 0);
 	pci_write_config_dword(pcidev, PCI_ROM_ADDRESS, BIOSImageBus | 0x1);
-
+#endif
 	udelay(1);
 
 	/*Check that the BIOS image is valid. If not fail, or return the
@@ -387,6 +441,16 @@ pcidev	- PCI device info for the video card on the bus
 REMARKS:
 Unmaps the BIOS image for the device and restores framebuffer mappings
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+void PCI_unmapBIOSImage(struct udevice *pcidev, void *BIOSImage)
+{
+	dm_pci_write_config32(pcidev, PCI_ROM_ADDRESS, saveROMBaseAddress);
+	dm_pci_write_config32(pcidev, PCI_BASE_ADDRESS_0, saveBaseAddress10);
+	dm_pci_write_config32(pcidev, PCI_BASE_ADDRESS_1, saveBaseAddress14);
+	dm_pci_write_config32(pcidev, PCI_BASE_ADDRESS_2, saveBaseAddress18);
+	dm_pci_write_config32(pcidev, PCI_BASE_ADDRESS_4, saveBaseAddress20);
+}
+#else
 void PCI_unmapBIOSImage(pci_dev_t pcidev, void *BIOSImage)
 {
 	pci_write_config_dword(pcidev, PCI_ROM_ADDRESS, saveROMBaseAddress);
@@ -395,6 +459,7 @@ void PCI_unmapBIOSImage(pci_dev_t pcidev, void *BIOSImage)
 	pci_write_config_dword(pcidev, PCI_BASE_ADDRESS_2, saveBaseAddress18);
 	pci_write_config_dword(pcidev, PCI_BASE_ADDRESS_4, saveBaseAddress20);
 }
+#endif
 
 /****************************************************************************
 PARAMETERS:
@@ -408,13 +473,22 @@ REMARKS:
 Loads and POST's the display controllers BIOS, directly from the BIOS
 image we can extract over the PCI bus.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+static int PCI_postController(struct udevice *pcidev, uchar *bios_rom,
+			      int bios_len, BE_VGAInfo *vga_info,
+			      int vesa_mode, struct vbe_mode_info *mode_info)
+#else
 static int PCI_postController(pci_dev_t pcidev, uchar *bios_rom, int bios_len,
 			      BE_VGAInfo *vga_info, int vesa_mode,
 			      struct vbe_mode_info *mode_info)
+#endif
 {
 	u32 bios_image_len;
 	uchar *mapped_bios;
 	uchar *copy_of_bios;
+#ifdef CONFIG_DM_PCI
+	pci_dev_t bdf;
+#endif
 
 	if (bios_rom) {
 		copy_of_bios = bios_rom;
@@ -442,9 +516,16 @@ static int PCI_postController(pci_dev_t pcidev, uchar *bios_rom, int bios_len,
 	}
 
 	/*Save information in vga_info structure*/
+#ifdef CONFIG_DM_PCI
+	bdf = dm_pci_get_bdf(pcidev);
+	vga_info->function = PCI_FUNC(bdf);
+	vga_info->device = PCI_DEV(bdf);
+	vga_info->bus = PCI_BUS(bdf);
+#else
 	vga_info->function = PCI_FUNC(pcidev);
 	vga_info->device = PCI_DEV(pcidev);
 	vga_info->bus = PCI_BUS(pcidev);
+#endif
 	vga_info->pcidev = pcidev;
 	vga_info->BIOSImage = copy_of_bios;
 	vga_info->BIOSImageLen = bios_image_len;
@@ -462,13 +543,22 @@ static int PCI_postController(pci_dev_t pcidev, uchar *bios_rom, int bios_len,
 	return true;
 }
 
+#ifdef CONFIG_DM_PCI
+int biosemu_setup(struct udevice *pcidev, BE_VGAInfo **vga_infop)
+#else
 int biosemu_setup(pci_dev_t pcidev, BE_VGAInfo **vga_infop)
+#endif
 {
 	BE_VGAInfo *VGAInfo;
+#ifdef CONFIG_DM_PCI
+	pci_dev_t bdf = dm_pci_get_bdf(pcidev);
 
 	printf("videoboot: Booting PCI video card bus %d, function %d, device %d\n",
-	     PCI_BUS(pcidev), PCI_FUNC(pcidev), PCI_DEV(pcidev));
-
+	       PCI_BUS(bdf), PCI_FUNC(bdf), PCI_DEV(bdf));
+#else
+	printf("videoboot: Booting PCI video card bus %d, function %d, device %d\n",
+	       PCI_BUS(pcidev), PCI_FUNC(pcidev), PCI_DEV(pcidev));
+#endif
 	/*Initialise the x86 BIOS emulator*/
 	if ((VGAInfo = malloc(sizeof(*VGAInfo))) == NULL) {
 		printf("videoboot: Out of memory!\n");
@@ -486,9 +576,15 @@ void biosemu_set_interrupt_handler(int intnum, int (*int_func)(void))
 	X86EMU_setupIntrFunc(intnum, (X86EMU_intrFuncs)int_func);
 }
 
+#ifdef CONFIG_DM_PCI
+int biosemu_run(struct udevice *pcidev, uchar *bios_rom, int bios_len,
+		BE_VGAInfo *vga_info, int clean_up, int vesa_mode,
+		struct vbe_mode_info *mode_info)
+#else
 int biosemu_run(pci_dev_t pcidev, uchar *bios_rom, int bios_len,
 		BE_VGAInfo *vga_info, int clean_up, int vesa_mode,
 		struct vbe_mode_info *mode_info)
+#endif
 {
 	/*Post all the display controller BIOS'es*/
 	if (!PCI_postController(pcidev, bios_rom, bios_len, vga_info,
@@ -522,7 +618,12 @@ REMARKS:
 Boots the PCI/AGP video card on the bus using the Video ROM BIOS image
 and the X86 BIOS emulator module.
 ****************************************************************************/
+#ifdef CONFIG_DM_PCI
+int BootVideoCardBIOS(struct udevice *pcidev, BE_VGAInfo **pVGAInfo,
+		      int clean_up)
+#else
 int BootVideoCardBIOS(pci_dev_t pcidev, BE_VGAInfo **pVGAInfo, int clean_up)
+#endif
 {
 	BE_VGAInfo *VGAInfo;
 	int ret;
drivers/bios_emulator/bios.c +39 -0
index dd4c0a4..77c7f94 100644
@@ -185,12 +185,21 @@ static void X86API int1A(int unused)
 	case 0xB103:		/* Find PCI class code */
 		M.x86.R_AH = DEVICE_NOT_FOUND;
 #ifdef __KERNEL__
+#ifdef CONFIG_DM_PCI
+		dm_pci_read_config8(_BE_env.vgaInfo.pcidev, PCI_CLASS_PROG,
+				    &interface);
+		dm_pci_read_config8(_BE_env.vgaInfo.pcidev, PCI_CLASS_DEVICE,
+				    &subclass);
+		dm_pci_read_config8(_BE_env.vgaInfo.pcidev,
+				    PCI_CLASS_DEVICE + 1, &baseclass);
+#else
 		pci_read_config_byte(_BE_env.vgaInfo.pcidev, PCI_CLASS_PROG,
 				     &interface);
 		pci_read_config_byte(_BE_env.vgaInfo.pcidev, PCI_CLASS_DEVICE,
 				     &subclass);
 		pci_read_config_byte(_BE_env.vgaInfo.pcidev,
 				     PCI_CLASS_DEVICE + 1, &baseclass);
+#endif
 		if (M.x86.R_CL == interface && M.x86.R_CH == subclass
 		    && (u8) (M.x86.R_ECX >> 16) == baseclass) {
 #else
@@ -209,8 +218,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_read_config8(_BE_env.vgaInfo.pcidev, M.x86.R_DI,
+					    &M.x86.R_CL);
+# else
 			pci_read_config_byte(_BE_env.vgaInfo.pcidev, M.x86.R_DI,
 					     &M.x86.R_CL);
+# endif
 #else
 			M.x86.R_CL =
 			    (u8) PCI_accessReg(M.x86.R_DI, 0, PCI_READ_BYTE,
@@ -224,8 +238,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_read_config16(_BE_env.vgaInfo.pcidev, M.x86.R_DI,
+					     &M.x86.R_CX);
+# else
 			pci_read_config_word(_BE_env.vgaInfo.pcidev, M.x86.R_DI,
 					     &M.x86.R_CX);
+# endif
 #else
 			M.x86.R_CX =
 			    (u16) PCI_accessReg(M.x86.R_DI, 0, PCI_READ_WORD,
@@ -239,8 +258,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_read_config32(_BE_env.vgaInfo.pcidev,
+					     M.x86.R_DI, &M.x86.R_ECX);
+# else
 			pci_read_config_dword(_BE_env.vgaInfo.pcidev,
 					      M.x86.R_DI, &M.x86.R_ECX);
+# endif
 #else
 			M.x86.R_ECX =
 			    (u32) PCI_accessReg(M.x86.R_DI, 0, PCI_READ_DWORD,
@@ -254,8 +278,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_write_config8(_BE_env.vgaInfo.pcidev,
+					     M.x86.R_DI, M.x86.R_CL);
+# else
 			pci_write_config_byte(_BE_env.vgaInfo.pcidev,
 					      M.x86.R_DI, M.x86.R_CL);
+# endif
 #else
 			PCI_accessReg(M.x86.R_DI, M.x86.R_CL, PCI_WRITE_BYTE,
 				      _BE_env.vgaInfo.pciInfo);
@@ -268,8 +297,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_write_config32(_BE_env.vgaInfo.pcidev,
+					      M.x86.R_DI, M.x86.R_CX);
+# else
 			pci_write_config_word(_BE_env.vgaInfo.pcidev,
 					      M.x86.R_DI, M.x86.R_CX);
+# endif
 #else
 			PCI_accessReg(M.x86.R_DI, M.x86.R_CX, PCI_WRITE_WORD,
 				      _BE_env.vgaInfo.pciInfo);
@@ -282,8 +316,13 @@ static void X86API int1A(int unused)
 		if (M.x86.R_BX == pciSlot) {
 			M.x86.R_AH = SUCCESSFUL;
 #ifdef __KERNEL__
+# ifdef CONFIG_DM_PCI
+			dm_pci_write_config32(_BE_env.vgaInfo.pcidev,
+					      M.x86.R_DI, M.x86.R_ECX);
+# else
 			pci_write_config_dword(_BE_env.vgaInfo.pcidev,
 					       M.x86.R_DI, M.x86.R_ECX);
+# endif
 #else
 			PCI_accessReg(M.x86.R_DI, M.x86.R_ECX, PCI_WRITE_DWORD,
 				      _BE_env.vgaInfo.pciInfo);
drivers/pci/pci_rom.c +3 -3
index 8c83be6..1b37820 100644
@@ -328,12 +328,12 @@ int dm_pci_run_vga_bios(struct udevice *dev, int (*int15_handler)(void),
 #ifdef CONFIG_BIOSEMU
 		BE_VGAInfo *info;
 
-		ret = biosemu_setup(dm_pci_get_bdf(dev), &info);
+		ret = biosemu_setup(dev, &info);
 		if (ret)
 			goto err;
 		biosemu_set_interrupt_handler(0x15, int15_handler);
-		ret = biosemu_run(dm_pci_get_bdf(dev), (uchar *)ram, 1 << 16,
-				  info, true, vesa_mode, &mode_info);
+		ret = biosemu_run(dev, (uchar *)ram, 1 << 16, info,
+				  true, vesa_mode, &mode_info);
 		if (ret)
 			goto err;
 #endif
include/bios_emul.h +18 -1
index 80979ed..7571263 100644
@@ -31,7 +31,11 @@ typedef struct {
 	int bus;
 	u32 VendorID;
 	u32 DeviceID;
+#ifdef CONFIG_DM_PCI
+	struct udevice *pcidev;
+#else
 	pci_dev_t pcidev;
+#endif
 	void *BIOSImage;
 	u32 BIOSImageLen;
 	u8 LowMem[1536];
@@ -39,7 +43,12 @@ typedef struct {
 
 struct vbe_mode_info;
 
-int BootVideoCardBIOS(pci_dev_t pcidev, BE_VGAInfo **pVGAInfo, int cleanUp);
+#ifdef CONFIG_DM_PCI
+int BootVideoCardBIOS(struct udevice *pcidev, BE_VGAInfo **pVGAInfo,
+		      int clean_up);
+#else
+int BootVideoCardBIOS(pci_dev_t pcidev, BE_VGAInfo **pVGAInfo, int clean_up);
+#endif
 
 /* Run a BIOS ROM natively (only supported on x86 machines) */
 void bios_run_on_x86(struct udevice *dev, unsigned long addr, int vesa_mode,
@@ -57,10 +66,18 @@ void bios_set_interrupt_handler(int intnum, int (*int_handler_func)(void));
 
 void biosemu_set_interrupt_handler(int intnum, int (*int_func)(void));
 
+#ifdef CONFIG_DM_PCI
+int biosemu_setup(struct udevice *pcidev, BE_VGAInfo **pVGAInfo);
+
+int biosemu_run(struct udevice *dev, uchar *bios_rom, int bios_len,
+		BE_VGAInfo *vga_info, int clean_up, int vesa_mode,
+		struct vbe_mode_info *mode_info);
+#else
 int biosemu_setup(pci_dev_t pcidev, BE_VGAInfo **pVGAInfo);
 
 int biosemu_run(pci_dev_t pcidev, uchar *bios_rom, int bios_len,
 		BE_VGAInfo *vga_info, int clean_up, int vesa_mode,
 		struct vbe_mode_info *mode_info);
+#endif
 
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#11 lore raw

PATCH v2 4/55 dm: pci: Convert bios_emu to use the driver model PCI API

Quoted 6 lines · Simon Glass

At present this BIOS emulator uses a bus/device/function number. Change it to use a device if CONFIG_DM_PCI is enabled.

---

Quoted 9 lines

Changes in v2:
- Drop unnecessary/incorrect non-DM code in dm_pci_run_vga_bios()

 drivers/bios_emulator/atibios.c | 109 ++++++++++++++++++++++++++++++++++++++--
 drivers/bios_emulator/bios.c    |  39 ++++++++++++++
 drivers/pci/pci_rom.c           |   6 +--
 include/bios_emul.h             |  19 ++++++-
 4 files changed, 165 insertions(+), 8 deletions(-)
#12 lore raw

PATCH v2 4/55 dm: pci: Convert bios_emu to use the driver model PCI API

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

At present this BIOS emulator uses a bus/device/function number. Change it to use a device if CONFIG_DM_PCI is enabled.

---

Changes in v2:
- Drop unnecessary/incorrect non-DM code in dm_pci_run_vga_bios()

Quoted 8 lines
Quoted 6 lines
 drivers/bios_emulator/atibios.c | 109 ++++++++++++++++++++++++++++++++++++++--
 drivers/bios_emulator/bios.c    |  39 ++++++++++++++
 drivers/pci/pci_rom.c           |   6 +--
 include/bios_emul.h             |  19 ++++++-
 4 files changed, 165 insertions(+), 8 deletions(-)

applied to u-boot-x86/master, thanks!

#13 lore raw

PATCH v2 5/55 x86: ivybridge: Set up the LPC device using driver model

In reply to Simon Glass

Find the LPC device in arch_cpu_init_dm() as a first step to converting this code to use driver model. Probing the LPC will probe its parent (the PCH) automatically, so make sure that probing the PCH does nothing before relocation.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c | 3 +++
 arch/x86/cpu/ivybridge/cpu.c     | 6 +++++-
 arch/x86/cpu/ivybridge/lpc.c     | 6 ++++++
 arch/x86/dts/chromebook_link.dts | 1 +
 4 files changed, 15 insertions(+), 1 deletion(-)
arch/x86/cpu/ivybridge/bd82x6x.c +3 -0
index c000aca..72f2ed4 100644
@@ -65,6 +65,9 @@ static int bd82x6x_probe(struct udevice *dev)
 	int sata_node, gma_node;
 	int ret;
 
+	if (!(gd->flags & GD_FLG_RELOC))
+		return 0;
+
 	hose = pci_bus_to_hose(0);
 	lpc_enable(PCH_LPC_DEV);
 	lpc_init(hose, PCH_LPC_DEV);
arch/x86/cpu/ivybridge/cpu.c +5 -1
index 343bfb4..6ffc843 100644
@@ -126,7 +126,7 @@ int arch_cpu_init_dm(void)
 {
 	const void *blob = gd->fdt_blob;
 	struct pci_controller *hose;
-	struct udevice *bus;
+	struct udevice *bus, *dev;
 	int node;
 	int ret;
 
@@ -141,6 +141,10 @@ int arch_cpu_init_dm(void)
 	/* TODO(sjg at chromium.org): Get rid of gd->hose */
 	gd->hose = hose;
 
+	ret = uclass_first_device(UCLASS_LPC, &dev);
+	if (!dev)
+		return -ENODEV;
+
 	node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_PCH);
 	if (node < 0)
 		return -ENOENT;
arch/x86/cpu/ivybridge/lpc.c +6 -0
index af5d4a8..51a4073 100644
@@ -559,6 +559,11 @@ void lpc_enable(pci_dev_t dev)
 	setbits_le32(RCB_REG(FD2), PCH_ENABLE_DBDF);
 }
 
+static int bd82x6x_lpc_probe(struct udevice *dev)
+{
+	return 0;
+}
+
 static const struct udevice_id bd82x6x_lpc_ids[] = {
 	{ .compatible = "intel,bd82x6x-lpc" },
 	{ }
@@ -568,4 +573,5 @@ U_BOOT_DRIVER(bd82x6x_lpc_drv) = {
 	.name		= "lpc",
 	.id		= UCLASS_LPC,
 	.of_match	= bd82x6x_lpc_ids,
+	.probe		= bd82x6x_lpc_probe,
 };
arch/x86/dts/chromebook_link.dts +1 -0
index a5c5dc1..d5c5bfd 100644
@@ -223,6 +223,7 @@
 				compatible = "intel,bd82x6x-lpc";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				u-boot,dm-pre-reloc;
 				cros-ec at 200 {
 					compatible = "google,cros-ec";
 					reg = <0x204 1 0x200 1 0x880 0x80>;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#14 lore raw

PATCH v2 5/55 x86: ivybridge: Set up the LPC device using driver model

Quoted 8 lines · Simon Glass

Find the LPC device in arch_cpu_init_dm() as a first step to converting this code to use driver model. Probing the LPC will probe its parent (the PCH) automatically, so make sure that probing the PCH does nothing before relocation.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c | 3 +++
 arch/x86/cpu/ivybridge/cpu.c     | 6 +++++-
 arch/x86/cpu/ivybridge/lpc.c     | 6 ++++++
 arch/x86/dts/chromebook_link.dts | 1 +
 4 files changed, 15 insertions(+), 1 deletion(-)
#15 lore raw

PATCH v2 5/55 x86: ivybridge: Set up the LPC device using driver model

Quoted 11 lines · Bin Meng
Quoted 10 lines · Simon Glass

Find the LPC device in arch_cpu_init_dm() as a first step to converting this code to use driver model. Probing the LPC will probe its parent (the PCH) automatically, so make sure that probing the PCH does nothing before relocation.

---

Changes in v2: None

Quoted 8 lines
Quoted 6 lines
 arch/x86/cpu/ivybridge/bd82x6x.c | 3 +++
 arch/x86/cpu/ivybridge/cpu.c     | 6 +++++-
 arch/x86/cpu/ivybridge/lpc.c     | 6 ++++++
 arch/x86/dts/chromebook_link.dts | 1 +
 4 files changed, 15 insertions(+), 1 deletion(-)

applied to u-boot-x86/master, thanks!

#16 lore raw

PATCH v2 6/55 x86: ivybridge: Move lpc_early_init() to probe()

In reply to Simon Glass

Move this code to the LPC's probe() method so that it will happen automatically when the LPC is probed before relocation.

---

Changes in v2:
- Drop unused 'gen-dec' device tree property

 arch/x86/cpu/ivybridge/cpu.c              |  9 ---------
 arch/x86/cpu/ivybridge/lpc.c              | 32 ++++++++++++++++++++++++-------
 arch/x86/dts/chromebook_link.dts          |  3 +--
 arch/x86/include/asm/arch-ivybridge/pch.h | 10 ----------
 4 files changed, 26 insertions(+), 28 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +0 -9
index 6ffc843..4c6ffb2 100644
@@ -124,10 +124,8 @@ int arch_cpu_init(void)
 
 int arch_cpu_init_dm(void)
 {
-	const void *blob = gd->fdt_blob;
 	struct pci_controller *hose;
 	struct udevice *bus, *dev;
-	int node;
 	int ret;
 
 	post_code(0x70);
@@ -145,13 +143,6 @@ int arch_cpu_init_dm(void)
 	if (!dev)
 		return -ENODEV;
 
-	node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_PCH);
-	if (node < 0)
-		return -ENOENT;
-	ret = lpc_early_init(gd->fdt_blob, node, PCH_LPC_DEV);
-	if (ret)
-		return ret;
-
 	enable_spi_prefetch(hose, PCH_LPC_DEV);
 
 	/* This is already done in start.S, but let's do it in C */
arch/x86/cpu/ivybridge/lpc.c +25 -7
index 51a4073..9d089c7 100644
@@ -454,7 +454,13 @@ static void pch_fixups(pci_dev_t dev)
 	setbits_le32(RCB_REG(0x21a8), 0x3);
 }
 
-int lpc_early_init(const void *blob, int node, pci_dev_t dev)
+/**
+ * lpc_early_init() - set up LPC serial ports and other early things
+ *
+ * @dev:	LPC device
+ * @return 0 if OK, -ve on error
+ */
+static int lpc_early_init(struct udevice *dev)
 {
 	struct reg_info {
 		u32 base;
@@ -463,17 +469,18 @@ int lpc_early_init(const void *blob, int node, pci_dev_t dev)
 	int count;
 	int i;
 
-	count = fdtdec_get_int_array_count(blob, node, "intel,gen-dec",
-			(u32 *)values, sizeof(values) / sizeof(u32));
+	count = fdtdec_get_int_array_count(gd->fdt_blob, dev->of_offset,
+			"intel,gen-dec", (u32 *)values,
+			sizeof(values) / sizeof(u32));
 	if (count < 0)
 		return -EINVAL;
 
 	/* Set COM1/COM2 decode range */
-	x86_pci_write_config16(dev, LPC_IO_DEC, 0x0010);
+	dm_pci_write_config16(dev->parent, LPC_IO_DEC, 0x0010);
 
 	/* Enable PS/2 Keyboard/Mouse, EC areas and COM1 */
-	x86_pci_write_config16(dev, LPC_EN, KBC_LPC_EN | MC_LPC_EN |
-			   GAMEL_LPC_EN | COMA_LPC_EN);
+	dm_pci_write_config16(dev->parent, LPC_EN, KBC_LPC_EN | MC_LPC_EN |
+			      GAMEL_LPC_EN | COMA_LPC_EN);
 
 	/* Write all registers but use 0 if we run out of data */
 	count = count * sizeof(u32) / sizeof(values[0]);
@@ -482,7 +489,7 @@ int lpc_early_init(const void *blob, int node, pci_dev_t dev)
 
 		if (i < count)
 			reg = ptr->base | PCI_COMMAND_IO | (ptr->size << 16);
-		x86_pci_write_config32(dev, LPC_GENX_DEC(i), reg);
+		dm_pci_write_config32(dev->parent, LPC_GENX_DEC(i), reg);
 	}
 
 	return 0;
@@ -561,6 +568,17 @@ void lpc_enable(pci_dev_t dev)
 
 static int bd82x6x_lpc_probe(struct udevice *dev)
 {
+	int ret;
+
+	if (gd->flags & GD_FLG_RELOC)
+		return 0;
+
+	ret = lpc_early_init(dev);
+	if (ret) {
+		debug("%s: lpc_early_init() failed\n", __func__);
+		return ret;
+	}
+
 	return 0;
 }
 
arch/x86/dts/chromebook_link.dts +1 -2
index d5c5bfd..f2db844 100644
@@ -192,8 +192,6 @@
 			u-boot,dm-pre-reloc;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			gen-dec = <0x800 0xfc 0x900 0xfc>;
-			intel,gen-dec = <0x800 0xfc 0x900 0xfc>;
 			intel,pirq-routing = <0x8b 0x8a 0x8b 0x8b
 						0x80 0x80 0x80 0x80>;
 			intel,gpi-routing = <0 0 0 0 0 0 0 2
@@ -224,6 +222,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				u-boot,dm-pre-reloc;
+				intel,gen-dec = <0x800 0xfc 0x900 0xfc>;
 				cros-ec at 200 {
 					compatible = "google,cros-ec";
 					reg = <0x204 1 0x200 1 0x880 0x80>;
arch/x86/include/asm/arch-ivybridge/pch.h +0 -10
index 31437c8..19cd7e5 100644
@@ -473,14 +473,4 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue);
 int lpc_init(struct pci_controller *hose, pci_dev_t dev);
 void lpc_enable(pci_dev_t dev);
 
-/**
- * lpc_early_init() - set up LPC serial ports and other early things
- *
- * @blob:	Device tree blob
- * @node:	Offset of LPC node
- * @dev:	PCH PCI device containing the LPC
- * @return 0 if OK, -ve on error
- */
-int lpc_early_init(const void *blob, int node, pci_dev_t dev);
-
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#17 lore raw

PATCH v2 6/55 x86: ivybridge: Move lpc_early_init() to probe()

Quoted 6 lines · Simon Glass

Move this code to the LPC's probe() method so that it will happen automatically when the LPC is probed before relocation.

---

Quoted 9 lines

Changes in v2:
- Drop unused 'gen-dec' device tree property

 arch/x86/cpu/ivybridge/cpu.c              |  9 ---------
 arch/x86/cpu/ivybridge/lpc.c              | 32 ++++++++++++++++++++++++-------
 arch/x86/dts/chromebook_link.dts          |  3 +--
 arch/x86/include/asm/arch-ivybridge/pch.h | 10 ----------
 4 files changed, 26 insertions(+), 28 deletions(-)
#18 lore raw

PATCH v2 6/55 x86: ivybridge: Move lpc_early_init() to probe()

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

Move this code to the LPC's probe() method so that it will happen automatically when the LPC is probed before relocation.

---

Changes in v2:
- Drop unused 'gen-dec' device tree property

Quoted 8 lines
Quoted 6 lines
 arch/x86/cpu/ivybridge/cpu.c              |  9 ---------
 arch/x86/cpu/ivybridge/lpc.c              | 32 ++++++++++++++++++++++++-------
 arch/x86/dts/chromebook_link.dts          |  3 +--
 arch/x86/include/asm/arch-ivybridge/pch.h | 10 ----------
 4 files changed, 26 insertions(+), 28 deletions(-)

applied to u-boot-x86/master, thanks!

#19 lore raw

PATCH v2 7/55 x86: ivybridge: Move more init to the probe() function

In reply to Simon Glass

Move SPI and port80 init to lpc_early_init(), called from the LPC's probe() method.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c | 43 -------------------------------------------
 arch/x86/cpu/ivybridge/lpc.c | 43 +++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+), 43 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +0 -43
index 4c6ffb2..1e6f656 100644
@@ -30,26 +30,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static void enable_port80_on_lpc(struct pci_controller *hose, pci_dev_t dev)
-{
-	/* Enable port 80 POST on LPC */
-	pci_hose_write_config_dword(hose, dev, PCH_RCBA_BASE, DEFAULT_RCBA | 1);
-	clrbits_le32(RCB_REG(GCS), 4);
-}
-
-/*
- * Enable Prefetching and Caching.
- */
-static void enable_spi_prefetch(struct pci_controller *hose, pci_dev_t dev)
-{
-	u8 reg8;
-
-	pci_hose_read_config_byte(hose, dev, 0xdc, &reg8);
-	reg8 &= ~(3 << 2);
-	reg8 |= (2 << 2); /* Prefetching and Caching Enabled */
-	pci_hose_write_config_byte(hose, dev, 0xdc, reg8);
-}
-
 static int set_flex_ratio_to_tdp_nominal(void)
 {
 	msr_t flex_ratio, msr;
@@ -99,22 +79,6 @@ static int set_flex_ratio_to_tdp_nominal(void)
 	return -EINVAL;
 }
 
-static void set_spi_speed(void)
-{
-	u32 fdod;
-
-	/* Observe SPI Descriptor Component Section 0 */
-	writel(0x1000, RCB_REG(SPI_DESC_COMP0));
-
-	/* Extract the1 Write/Erase SPI Frequency from descriptor */
-	fdod = readl(RCB_REG(SPI_FREQ_WR_ERA));
-	fdod >>= 24;
-	fdod &= 7;
-
-	/* Set Software Sequence frequency to match */
-	clrsetbits_8(RCB_REG(SPI_FREQ_SWSEQ), 7, fdod);
-}
-
 int arch_cpu_init(void)
 {
 	post_code(POST_CPU_INIT);
@@ -143,13 +107,6 @@ int arch_cpu_init_dm(void)
 	if (!dev)
 		return -ENODEV;
 
-	enable_spi_prefetch(hose, PCH_LPC_DEV);
-
-	/* This is already done in start.S, but let's do it in C */
-	enable_port80_on_lpc(hose, PCH_LPC_DEV);
-
-	set_spi_speed();
-
 	/*
 	 * We should do as little as possible before the serial console is
 	 * up. Perhaps this should move to later. Our next lot of init
arch/x86/cpu/ivybridge/lpc.c +43 -0

55 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#20 lore raw

PATCH v2 7/55 x86: ivybridge: Move more init to the probe() function

Quoted 5 lines · Simon Glass

Move SPI and port80 init to lpc_early_init(), called from the LPC's probe() method.

Quoted 8 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c | 43 -------------------------------------------
 arch/x86/cpu/ivybridge/lpc.c | 43 +++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+), 43 deletions(-)

applied to u-boot-x86/master, thanks!

#21 lore raw

PATCH v2 8/55 x86: ivybridge: Rename bd82x6x_init()

In reply to Simon Glass

Rename the existing bd82x6x_init() to bd82x6x_init_extra(). We will remove this in a later patch.

---

Changes in v2:
- Drop the init() method in the PCH
- Rename this commit from 'x86: ivybridge: Set up the PCH init'

 arch/x86/cpu/ivybridge/bd82x6x.c              | 2 +-
 arch/x86/cpu/ivybridge/cpu.c                  | 8 ++++++++
 arch/x86/cpu/ivybridge/pci.c                  | 2 +-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h | 2 +-
 4 files changed, 11 insertions(+), 3 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +1 -1
index 72f2ed4..6556eeb 100644
@@ -102,7 +102,7 @@ static int bd82x6x_probe(struct udevice *dev)
 }
 
 /* TODO(sjg at chromium.org): Move this to the PCH init() method */
-int bd82x6x_init(void)
+int bd82x6x_init_extra(void)
 {
 	const void *blob = gd->fdt_blob;
 	int sata_node;
arch/x86/cpu/ivybridge/cpu.c +8 -0
index 1e6f656..2a15fc0 100644
@@ -15,6 +15,7 @@
 #include <dm.h>
 #include <errno.h>
 #include <fdtdec.h>
+#include <pch.h>
 #include <asm/cpu.h>
 #include <asm/io.h>
 #include <asm/lapic.h>
@@ -211,6 +212,7 @@ int print_cpuinfo(void)
 {
 	enum pei_boot_mode_t boot_mode = PEI_BOOT_NONE;
 	char processor_name[CPU_MAX_NAME_LEN];
+	struct udevice *dev;
 	const char *name;
 	uint32_t pm1_cnt;
 	uint16_t pm1_sts;
@@ -241,6 +243,12 @@ int print_cpuinfo(void)
 	}
 
 	/* Early chipset init required before RAM init can work */
+	ret = uclass_first_device(UCLASS_PCH, &dev);
+	if (ret)
+		return ret;
+	if (!dev)
+		return -ENODEV;
+
 	sandybridge_early_init(SANDYBRIDGE_MOBILE);
 
 	/* Check PM1_STS[15] to see if we are waking from Sx */
arch/x86/cpu/ivybridge/pci.c +1 -1
index 5e90f30..8af99b4 100644
@@ -26,7 +26,7 @@ static int pci_ivybridge_probe(struct udevice *bus)
 	if (!(gd->flags & GD_FLG_RELOC))
 		return 0;
 	post_code(0x50);
-	bd82x6x_init();
+	bd82x6x_init_extra();
 	post_code(0x51);
 
 	reg16 = 0xff;
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +1 -1
index fcdf6e2..d76cb8d 100644
@@ -13,7 +13,7 @@ void bd82x6x_pci_init(pci_dev_t dev);
 void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
-int bd82x6x_init(void);
+int bd82x6x_init_extra(void);
 
 /**
  * struct x86_cpu_priv - Information about a single CPU
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#22 lore raw

PATCH v2 8/55 x86: ivybridge: Rename bd82x6x_init()

Quoted 10 lines · Simon Glass

Rename the existing bd82x6x_init() to bd82x6x_init_extra(). We will remove this in a later patch.

---

Changes in v2:
- Drop the init() method in the PCH
- Rename this commit from 'x86: ivybridge: Set up the PCH init'

Quoted 6 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              | 2 +-
 arch/x86/cpu/ivybridge/cpu.c                  | 8 ++++++++
 arch/x86/cpu/ivybridge/pci.c                  | 2 +-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h | 2 +-
 4 files changed, 11 insertions(+), 3 deletions(-)
#23 lore raw

PATCH v2 8/55 x86: ivybridge: Rename bd82x6x_init()

Quoted 11 lines · Bin Meng
Quoted 10 lines · Simon Glass

Rename the existing bd82x6x_init() to bd82x6x_init_extra(). We will remove this in a later patch.

---

Changes in v2:
- Drop the init() method in the PCH
- Rename this commit from 'x86: ivybridge: Set up the PCH init'

Quoted 8 lines
Quoted 6 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              | 2 +-
 arch/x86/cpu/ivybridge/cpu.c                  | 8 ++++++++
 arch/x86/cpu/ivybridge/pci.c                  | 2 +-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h | 2 +-
 4 files changed, 11 insertions(+), 3 deletions(-)

applied to u-boot-x86/master, thanks!

#24 lore raw

PATCH v2 9/55 dm: x86: Add a northbridge uclass

In reply to Simon Glass

Add a uclass for the northbridge / SDRAM controller found on some older Intel chipsets.

---

Changes in v2:
- Drop unnecessary DECLARE_GLOBAL_DATA_PTR

 arch/x86/lib/Makefile             |  1 +
 arch/x86/lib/northbridge-uclass.c | 15 +++++++++++++++
 include/dm/uclass-id.h            |  1 +
 3 files changed, 17 insertions(+)
 create mode 100644 arch/x86/lib/northbridge-uclass.c
arch/x86/lib/Makefile +1 -0
index 43792bc..d9fc296 100644
@@ -19,6 +19,7 @@ obj-y	+= lpc-uclass.o
 obj-y	+= mpspec.o
 obj-$(CONFIG_ENABLE_MRC_CACHE) += mrccache.o
 obj-y += cmd_mtrr.o
+obj-y	+= northbridge-uclass.o
 obj-$(CONFIG_I8259_PIC) += i8259.o
 obj-$(CONFIG_I8254_TIMER) += i8254.o
 ifndef CONFIG_DM_PCI
arch/x86/lib/northbridge-uclass.c new file +15 -0
new file mode 100644
index 0000000..64b6257
@@ -0,0 +1,15 @@
+/*
+ * Copyright (c) 2015 Google, Inc
+ * Written by Simon Glass <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/root.h>
+
+UCLASS_DRIVER(northbridge) = {
+	.id		= UCLASS_NORTHBRIDGE,
+	.name		= "northbridge",
+};
include/dm/uclass-id.h +1 -0
index ef145af..4a6827b 100644
@@ -46,6 +46,7 @@ enum uclass_id {
 	UCLASS_MMC,		/* SD / MMC card or chip */
 	UCLASS_MOD_EXP,		/* RSA Mod Exp device */
 	UCLASS_MTD,		/* Memory Technology Device (MTD) device */
+	UCLASS_NORTHBRIDGE,	/* Intel Northbridge / SDRAM controller */
 	UCLASS_PCH,		/* x86 platform controller hub */
 	UCLASS_PCI,		/* PCI bus */
 	UCLASS_PCI_GENERIC,	/* Generic PCI bus device */
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#25 lore raw

PATCH v2 9/55 dm: x86: Add a northbridge uclass

Quoted 7 lines · Simon Glass

Add a uclass for the northbridge / SDRAM controller found on some older Intel chipsets.

---

Quoted 9 lines

Changes in v2:
- Drop unnecessary DECLARE_GLOBAL_DATA_PTR

 arch/x86/lib/Makefile             |  1 +
 arch/x86/lib/northbridge-uclass.c | 15 +++++++++++++++
 include/dm/uclass-id.h            |  1 +
 3 files changed, 17 insertions(+)
 create mode 100644 arch/x86/lib/northbridge-uclass.c

applied to u-boot-x86/master, thanks!

#26 lore raw

PATCH v2 10/55 x86: ivybridge: Add a driver for the bd82x6x northbridge

In reply to Simon Glass

Add a driver with an empty probe function where we can move init code in follow-on patches.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/early_init.c | 18 ++++++++++++++++++
 arch/x86/dts/chromebook_link.dts    |  7 +++++++
 2 files changed, 25 insertions(+)
arch/x86/cpu/ivybridge/early_init.c +18 -0
index 9ca008e..945ae2d 100644
@@ -8,6 +8,7 @@
  */
 
 #include <common.h>
+#include <dm.h>
 #include <asm/io.h>
 #include <asm/pci.h>
 #include <asm/arch/pch.h>
@@ -145,3 +146,20 @@ void sandybridge_early_init(int chipset_type)
 
 	sandybridge_setup_graphics(pch_dev, video_dev);
 }
+
+static int bd82x6x_northbridge_probe(struct udevice *dev)
+{
+	return 0;
+}
+
+static const struct udevice_id bd82x6x_northbridge_ids[] = {
+	{ .compatible = "intel,bd82x6x-northbridge" },
+	{ }
+};
+
+U_BOOT_DRIVER(bd82x6x_northbridge_drv) = {
+	.name		= "bd82x6x_northbridge",
+	.id		= UCLASS_NORTHBRIDGE,
+	.of_match	= bd82x6x_northbridge_ids,
+	.probe		= bd82x6x_northbridge_probe,
+};
arch/x86/dts/chromebook_link.dts +7 -0
index f2db844..e2c722d 100644
@@ -166,6 +166,13 @@
 		ranges = <0x02000000 0x0 0xe0000000 0xe0000000 0 0x10000000
 			0x42000000 0x0 0xd0000000 0xd0000000 0 0x10000000
 			0x01000000 0x0 0x1000 0x1000 0 0xefff>;
+
+		northbridge at 0,0 {
+			reg = <0x00000000 0 0 0 0>;
+			compatible = "intel,bd82x6x-northbridge";
+			u-boot,dm-pre-reloc;
+		};
+
 		sata {
 			compatible = "intel,pantherpoint-ahci";
 			intel,sata-mode = "ahci";
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#27 lore raw

PATCH v2 10/55 x86: ivybridge: Add a driver for the bd82x6x northbridge

Quoted 5 lines · Simon Glass

Add a driver with an empty probe function where we can move init code in follow-on patches.

Quoted 8 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/early_init.c | 18 ++++++++++++++++++
 arch/x86/dts/chromebook_link.dts    |  7 +++++++
 2 files changed, 25 insertions(+)

applied to u-boot-x86/master, thanks!

#28 lore raw

PATCH v2 11/55 x86: ivybridge: Move northbridge init into the probe() method

In reply to Simon Glass

Now that we have a proper driver for the nortbridge, set it up in by probing it, and move the early init code into the probe() method.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c        |  2 ++
 arch/x86/cpu/ivybridge/early_init.c | 33 +++++++++++++++++++--------------
 2 files changed, 21 insertions(+), 14 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +2 -0
index 2a15fc0..f32b4a1 100644
@@ -243,6 +243,8 @@ int print_cpuinfo(void)
 	}
 
 	/* Early chipset init required before RAM init can work */
+	uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
+
 	ret = uclass_first_device(UCLASS_PCH, &dev);
 	if (ret)
 		return ret;
arch/x86/cpu/ivybridge/early_init.c +19 -14
index 945ae2d..c629f5b 100644
@@ -123,20 +123,6 @@ void sandybridge_early_init(int chipset_type)
 	pci_dev_t pch_dev = PCH_DEV;
 	pci_dev_t video_dev = PCH_VIDEO_DEV;
 	pci_dev_t lpc_dev = PCH_LPC_DEV;
-	u32 capid0_a;
-	u8 reg8;
-
-	/* Device ID Override Enable should be done very early */
-	capid0_a = x86_pci_read_config32(pch_dev, 0xe4);
-	if (capid0_a & (1 << 10)) {
-		reg8 = x86_pci_read_config8(pch_dev, 0xf3);
-		reg8 &= ~7; /* Clear 2:0 */
-
-		if (chipset_type == SANDYBRIDGE_MOBILE)
-			reg8 |= 1; /* Set bit 0 */
-
-		x86_pci_write_config8(pch_dev, 0xf3, reg8);
-	}
 
 	/* Setup all BARs required for early PCIe and raminit */
 	sandybridge_setup_bars(pch_dev, lpc_dev);
@@ -149,6 +135,25 @@ void sandybridge_early_init(int chipset_type)
 
 static int bd82x6x_northbridge_probe(struct udevice *dev)
 {
+	const int chipset_type = SANDYBRIDGE_MOBILE;
+	u32 capid0_a;
+	u8 reg8;
+
+	if (gd->flags & GD_FLG_RELOC)
+		return 0;
+
+	/* Device ID Override Enable should be done very early */
+	dm_pci_read_config32(dev, 0xe4, &capid0_a);
+	if (capid0_a & (1 << 10)) {
+		dm_pci_read_config8(dev, 0xf3, &reg8);
+		reg8 &= ~7; /* Clear 2:0 */
+
+		if (chipset_type == SANDYBRIDGE_MOBILE)
+			reg8 |= 1; /* Set bit 0 */
+
+		dm_pci_write_config8(dev, 0xf3, reg8);
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#29 lore raw

PATCH v2 11/55 x86: ivybridge: Move northbridge init into the probe() method

Quoted 5 lines · Simon Glass

Now that we have a proper driver for the nortbridge, set it up in by probing it, and move the early init code into the probe() method.

Quoted 8 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c        |  2 ++
 arch/x86/cpu/ivybridge/early_init.c | 33 +++++++++++++++++++--------------
 2 files changed, 21 insertions(+), 14 deletions(-)

applied to u-boot-x86/master, thanks!

#30 lore raw

PATCH v2 12/55 x86: ivybridge: Move LPC and PCH init into northbridge probe()

In reply to Simon Glass

Move more code into the northbridge probe() function.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/early_init.c | 47 +++++++++++++++++++------------------
 1 file changed, 24 insertions(+), 23 deletions(-)
arch/x86/cpu/ivybridge/early_init.c +24 -23
index c629f5b..029f5ef 100644
@@ -14,7 +14,7 @@
 #include <asm/arch/pch.h>
 #include <asm/arch/sandybridge.h>
 
-static void sandybridge_setup_bars(pci_dev_t pch_dev, pci_dev_t lpc_dev)
+static void sandybridge_setup_lpc_bars(pci_dev_t lpc_dev)
 {
 	/* Setting up Southbridge. In the northbridge code. */
 	debug("Setting up static southbridge registers\n");
@@ -26,30 +26,31 @@ static void sandybridge_setup_bars(pci_dev_t pch_dev, pci_dev_t lpc_dev)
 	debug("Disabling watchdog reboot\n");
 	setbits_le32(RCB_REG(GCS), 1 >> 5);	/* No reset */
 	outw(1 << 11, DEFAULT_PMBASE | 0x60 | 0x08);	/* halt timer */
+}
 
+static void sandybridge_setup_northbridge_bars(struct udevice *dev)
+{
 	/* Set up all hardcoded northbridge BARs */
 	debug("Setting up static registers\n");
-	x86_pci_write_config32(pch_dev, EPBAR, DEFAULT_EPBAR | 1);
-	x86_pci_write_config32(pch_dev, EPBAR + 4, (0LL + DEFAULT_EPBAR) >> 32);
-	x86_pci_write_config32(pch_dev, MCHBAR, DEFAULT_MCHBAR | 1);
-	x86_pci_write_config32(pch_dev, MCHBAR + 4,
-			       (0LL + DEFAULT_MCHBAR) >> 32);
+	dm_pci_write_config32(dev, EPBAR, DEFAULT_EPBAR | 1);
+	dm_pci_write_config32(dev, EPBAR + 4, (0LL + DEFAULT_EPBAR) >> 32);
+	dm_pci_write_config32(dev, MCHBAR, DEFAULT_MCHBAR | 1);
+	dm_pci_write_config32(dev, MCHBAR + 4, (0LL + DEFAULT_MCHBAR) >> 32);
 	/* 64MB - busses 0-63 */
-	x86_pci_write_config32(pch_dev, PCIEXBAR, DEFAULT_PCIEXBAR | 5);
-	x86_pci_write_config32(pch_dev, PCIEXBAR + 4,
-			       (0LL + DEFAULT_PCIEXBAR) >> 32);
-	x86_pci_write_config32(pch_dev, DMIBAR, DEFAULT_DMIBAR | 1);
-	x86_pci_write_config32(pch_dev, DMIBAR + 4,
-			       (0LL + DEFAULT_DMIBAR) >> 32);
+	dm_pci_write_config32(dev, PCIEXBAR, DEFAULT_PCIEXBAR | 5);
+	dm_pci_write_config32(dev, PCIEXBAR + 4,
+			      (0LL + DEFAULT_PCIEXBAR) >> 32);
+	dm_pci_write_config32(dev, DMIBAR, DEFAULT_DMIBAR | 1);
+	dm_pci_write_config32(dev, DMIBAR + 4, (0LL + DEFAULT_DMIBAR) >> 32);
 
 	/* Set C0000-FFFFF to access RAM on both reads and writes */
-	x86_pci_write_config8(pch_dev, PAM0, 0x30);
-	x86_pci_write_config8(pch_dev, PAM1, 0x33);
-	x86_pci_write_config8(pch_dev, PAM2, 0x33);
-	x86_pci_write_config8(pch_dev, PAM3, 0x33);
-	x86_pci_write_config8(pch_dev, PAM4, 0x33);
-	x86_pci_write_config8(pch_dev, PAM5, 0x33);
-	x86_pci_write_config8(pch_dev, PAM6, 0x33);
+	dm_pci_write_config8(dev, PAM0, 0x30);
+	dm_pci_write_config8(dev, PAM1, 0x33);
+	dm_pci_write_config8(dev, PAM2, 0x33);
+	dm_pci_write_config8(dev, PAM3, 0x33);
+	dm_pci_write_config8(dev, PAM4, 0x33);
+	dm_pci_write_config8(dev, PAM5, 0x33);
+	dm_pci_write_config8(dev, PAM6, 0x33);
 }
 
 static void sandybridge_setup_graphics(pci_dev_t pch_dev, pci_dev_t video_dev)
@@ -122,10 +123,6 @@ void sandybridge_early_init(int chipset_type)
 {
 	pci_dev_t pch_dev = PCH_DEV;
 	pci_dev_t video_dev = PCH_VIDEO_DEV;
-	pci_dev_t lpc_dev = PCH_LPC_DEV;
-
-	/* Setup all BARs required for early PCIe and raminit */
-	sandybridge_setup_bars(pch_dev, lpc_dev);
 
 	/* Device Enable */
 	x86_pci_write_config32(pch_dev, DEVEN, DEVEN_HOST | DEVEN_IGD);
@@ -154,6 +151,10 @@ static int bd82x6x_northbridge_probe(struct udevice *dev)
 		dm_pci_write_config8(dev, 0xf3, reg8);
 	}
 
+	sandybridge_setup_lpc_bars(PCH_LPC_DEV);
+
+	sandybridge_setup_northbridge_bars(dev);
+
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#31 lore raw

PATCH v2 12/55 x86: ivybridge: Move LPC and PCH init into northbridge probe()

Quoted 11 lines · Simon Glass

Move more code into the northbridge probe() function.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/early_init.c | 47 +++++++++++++++++++------------------
 1 file changed, 24 insertions(+), 23 deletions(-)

applied to u-boot-x86/master, thanks!

#32 lore raw

PATCH v2 13/55 x86: ivybridge: Rename lpc_init() to lpc_init_extra()

In reply to Simon Glass

In preparation for adding an init() method to the LPC uclass, rename this existing function so that it will not conflict.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c          | 2 +-
 arch/x86/cpu/ivybridge/lpc.c              | 2 +-
 arch/x86/include/asm/arch-ivybridge/pch.h | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +1 -1
index 6556eeb..c71596d 100644
@@ -70,7 +70,7 @@ static int bd82x6x_probe(struct udevice *dev)
 
 	hose = pci_bus_to_hose(0);
 	lpc_enable(PCH_LPC_DEV);
-	lpc_init(hose, PCH_LPC_DEV);
+	lpc_init_extra(hose, PCH_LPC_DEV);
 	sata_node = fdtdec_next_compatible(blob, 0,
 					   COMPAT_INTEL_PANTHERPOINT_AHCI);
 	if (sata_node < 0) {
arch/x86/cpu/ivybridge/lpc.c +1 -1
index 9dad9e4..9f41f22 100644
@@ -538,7 +538,7 @@ static int lpc_early_init(struct udevice *dev)
 	return 0;
 }
 
-int lpc_init(struct pci_controller *hose, pci_dev_t dev)
+int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev)
 {
 	const void *blob = gd->fdt_blob;
 	int node;
arch/x86/include/asm/arch-ivybridge/pch.h +1 -1
index 19cd7e5..f35803b 100644
@@ -470,7 +470,7 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue);
 #define   DMISCI_STS	(1 << 9)
 #define TCO2_STS	0x66
 
-int lpc_init(struct pci_controller *hose, pci_dev_t dev);
+int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev);
 void lpc_enable(pci_dev_t dev);
 
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#33 lore raw

PATCH v2 13/55 x86: ivybridge: Rename lpc_init() to lpc_init_extra()

Quoted 4 lines · Simon Glass

In preparation for adding an init() method to the LPC uclass, rename this existing function so that it will not conflict.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c          | 2 +-
 arch/x86/cpu/ivybridge/lpc.c              | 2 +-
 arch/x86/include/asm/arch-ivybridge/pch.h | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)
#34 lore raw

PATCH v2 13/55 x86: ivybridge: Rename lpc_init() to lpc_init_extra()

Quoted 9 lines · Bin Meng
Quoted 8 lines · Simon Glass

In preparation for adding an init() method to the LPC uclass, rename this existing function so that it will not conflict.

---

Changes in v2: None

Quoted 7 lines
Quoted 5 lines
 arch/x86/cpu/ivybridge/bd82x6x.c          | 2 +-
 arch/x86/cpu/ivybridge/lpc.c              | 2 +-
 arch/x86/include/asm/arch-ivybridge/pch.h | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

applied to u-boot-x86/master, thanks!

#35 lore raw

PATCH v2 14/55 x86: ivybridge: Probe the LPC in CPU init

In reply to Simon Glass

We can drop the explicit probe of the PCH since the LPC is a child device and this will happen automatically.

---

Changes in v2:
- Drop explicit PCH probe
- Drop LPC init method
- Rename patch from 'Add an init() method for the bd82x6x LPC'

 arch/x86/cpu/ivybridge/cpu.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +2 -3
index f32b4a1..65eea1f 100644
@@ -212,7 +212,7 @@ int print_cpuinfo(void)
 {
 	enum pei_boot_mode_t boot_mode = PEI_BOOT_NONE;
 	char processor_name[CPU_MAX_NAME_LEN];
-	struct udevice *dev;
+	struct udevice *dev, *lpc;
 	const char *name;
 	uint32_t pm1_cnt;
 	uint16_t pm1_sts;
@@ -245,12 +245,11 @@ int print_cpuinfo(void)
 	/* Early chipset init required before RAM init can work */
 	uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
 
-	ret = uclass_first_device(UCLASS_PCH, &dev);
+	ret = uclass_first_device(UCLASS_LPC, &lpc);
 	if (ret)
 		return ret;
 	if (!dev)
 		return -ENODEV;
-
 	sandybridge_early_init(SANDYBRIDGE_MOBILE);
 
 	/* Check PM1_STS[15] to see if we are waking from Sx */
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#36 lore raw

PATCH v2 14/55 x86: ivybridge: Probe the LPC in CPU init

Quoted 6 lines · Simon Glass

We can drop the explicit probe of the PCH since the LPC is a child device and this will happen automatically.

---

Quoted 8 lines

Changes in v2:
- Drop explicit PCH probe
- Drop LPC init method
- Rename patch from 'Add an init() method for the bd82x6x LPC'

 arch/x86/cpu/ivybridge/cpu.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
#37 lore raw

PATCH v2 14/55 x86: ivybridge: Probe the LPC in CPU init

Quoted 12 lines · Bin Meng
Quoted 11 lines · Simon Glass

We can drop the explicit probe of the PCH since the LPC is a child device and this will happen automatically.

---

Changes in v2:
- Drop explicit PCH probe
- Drop LPC init method
- Rename patch from 'Add an init() method for the bd82x6x LPC'

Quoted 5 lines
Quoted 3 lines
 arch/x86/cpu/ivybridge/cpu.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

applied to u-boot-x86/master, thanks!

#38 lore raw

PATCH v2 15/55 x86: ivybridge: Move graphics init much later

In reply to Simon Glass

We don't need to init the graphics controller so early. Move it alongside the other graphics setup, just before we run the ROM.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c        |  1 -
 arch/x86/cpu/ivybridge/early_init.c | 80 ++-----------------------------------
 arch/x86/cpu/ivybridge/gma.c        | 73 +++++++++++++++++++++++++++++++++
 3 files changed, 76 insertions(+), 78 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +0 -1
index 65eea1f..c3626c4 100644
@@ -250,7 +250,6 @@ int print_cpuinfo(void)
 		return ret;
 	if (!dev)
 		return -ENODEV;
-	sandybridge_early_init(SANDYBRIDGE_MOBILE);
 
 	/* Check PM1_STS[15] to see if we are waking from Sx */
 	pm1_sts = inw(DEFAULT_PMBASE + PM1_STS);
arch/x86/cpu/ivybridge/early_init.c +3 -77

92 lines not on this page · raw message

arch/x86/cpu/ivybridge/gma.c +73 -0

95 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#39 lore raw

PATCH v2 15/55 x86: ivybridge: Move graphics init much later

Quoted 5 lines · Simon Glass

We don't need to init the graphics controller so early. Move it alongside the other graphics setup, just before we run the ROM.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c        |  1 -
 arch/x86/cpu/ivybridge/early_init.c | 80 ++-----------------------------------
 arch/x86/cpu/ivybridge/gma.c        | 73 +++++++++++++++++++++++++++++++++
 3 files changed, 76 insertions(+), 78 deletions(-)

applied to u-boot-x86/master, thanks!

#40 lore raw

PATCH v2 16/55 x86: ivybridge: Move sandybridge init to the lpc probe() method

In reply to Simon Glass

The watchdog can be reset later when probing the LPC after relocation. Move it.

---

Changes in v2:
- Update to drop LPC init method and use probe() instead

 arch/x86/cpu/ivybridge/early_init.c | 16 ----------------
 arch/x86/cpu/ivybridge/lpc.c        | 19 ++++++++++++++++++-
 2 files changed, 18 insertions(+), 17 deletions(-)
arch/x86/cpu/ivybridge/early_init.c +0 -16
index 83ef7b7..5b16abc 100644
@@ -14,20 +14,6 @@
 #include <asm/arch/pch.h>
 #include <asm/arch/sandybridge.h>
 
-static void sandybridge_setup_lpc_bars(pci_dev_t lpc_dev)
-{
-	/* Setting up Southbridge. In the northbridge code. */
-	debug("Setting up static southbridge registers\n");
-	x86_pci_write_config32(lpc_dev, PCH_RCBA_BASE, DEFAULT_RCBA | 1);
-
-	x86_pci_write_config32(lpc_dev, PMBASE, DEFAULT_PMBASE | 1);
-	x86_pci_write_config8(lpc_dev, ACPI_CNTL, 0x80); /* Enable ACPI BAR */
-
-	debug("Disabling watchdog reboot\n");
-	setbits_le32(RCB_REG(GCS), 1 >> 5);	/* No reset */
-	outw(1 << 11, DEFAULT_PMBASE | 0x60 | 0x08);	/* halt timer */
-}
-
 static void sandybridge_setup_northbridge_bars(struct udevice *dev)
 {
 	/* Set up all hardcoded northbridge BARs */
@@ -74,8 +60,6 @@ static int bd82x6x_northbridge_probe(struct udevice *dev)
 		dm_pci_write_config8(dev, 0xf3, reg8);
 	}
 
-	sandybridge_setup_lpc_bars(PCH_LPC_DEV);
-
 	sandybridge_setup_northbridge_bars(dev);
 
 	/* Device Enable */
arch/x86/cpu/ivybridge/lpc.c +18 -1
index 9f41f22..c88733d 100644
@@ -609,6 +609,23 @@ void lpc_enable(pci_dev_t dev)
 	setbits_le32(RCB_REG(FD2), PCH_ENABLE_DBDF);
 }
 
+static int bd82x6x_lpc_early_init(struct udevice *dev)
+{
+	/* Setting up Southbridge. In the northbridge code. */
+	debug("Setting up static southbridge registers\n");
+	dm_pci_write_config32(dev->parent, PCH_RCBA_BASE, DEFAULT_RCBA | 1);
+	dm_pci_write_config32(dev->parent, PMBASE, DEFAULT_PMBASE | 1);
+
+	/* Enable ACPI BAR */
+	dm_pci_write_config8(dev->parent, ACPI_CNTL, 0x80);
+
+	debug("Disabling watchdog reboot\n");
+	setbits_le32(RCB_REG(GCS), 1 >> 5);	/* No reset */
+	outw(1 << 11, DEFAULT_PMBASE | 0x60 | 0x08);	/* halt timer */
+
+	return 0;
+}
+
 static int bd82x6x_lpc_probe(struct udevice *dev)
 {
 	int ret;
@@ -622,7 +639,7 @@ static int bd82x6x_lpc_probe(struct udevice *dev)
 		return ret;
 	}
 
-	return 0;
+	return bd82x6x_lpc_early_init(dev);
 }
 
 static const struct udevice_id bd82x6x_lpc_ids[] = {
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#41 lore raw

PATCH v2 16/55 x86: ivybridge: Move sandybridge init to the lpc probe() method

Quoted 5 lines · Simon Glass

The watchdog can be reset later when probing the LPC after relocation. Move it.

Quoted 9 lines

---

Changes in v2:
- Update to drop LPC init method and use probe() instead

 arch/x86/cpu/ivybridge/early_init.c | 16 ----------------
 arch/x86/cpu/ivybridge/lpc.c        | 19 ++++++++++++++++++-
 2 files changed, 18 insertions(+), 17 deletions(-)

applied to u-boot-x86/master, thanks!

#42 lore raw

PATCH v2 17/55 x86: ivybridge: Move GPIO init to the LPC init() method

In reply to Simon Glass

This init can happen in the driver also. Move it.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c | 4 ----
 arch/x86/cpu/ivybridge/lpc.c | 3 +++
 2 files changed, 3 insertions(+), 4 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +0 -4
index c3626c4..6d3f477 100644
@@ -278,10 +278,6 @@ int print_cpuinfo(void)
 
 	gd->arch.pei_boot_mode = boot_mode;
 
-	/* TODO: Move this to the board or driver */
-	x86_pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE | 1);
-	x86_pci_write_config32(PCH_LPC_DEV, GPIO_CNTL, 0x10);
-
 	/* Print processor name */
 	name = cpu_get_name(processor_name);
 	printf("CPU:   %s\n", name);
arch/x86/cpu/ivybridge/lpc.c +3 -0
index c88733d..0d85de2 100644
@@ -623,6 +623,9 @@ static int bd82x6x_lpc_early_init(struct udevice *dev)
 	setbits_le32(RCB_REG(GCS), 1 >> 5);	/* No reset */
 	outw(1 << 11, DEFAULT_PMBASE | 0x60 | 0x08);	/* halt timer */
 
+	dm_pci_write_config32(dev->parent, GPIO_BASE, DEFAULT_GPIOBASE | 1);
+	dm_pci_write_config32(dev->parent, GPIO_CNTL, 0x10);
+
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#43 lore raw

PATCH v2 17/55 x86: ivybridge: Move GPIO init to the LPC init() method

Quoted 4 lines · Simon Glass

This init can happen in the driver also. Move it.

Quoted 8 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c | 4 ----
 arch/x86/cpu/ivybridge/lpc.c | 3 +++
 2 files changed, 3 insertions(+), 4 deletions(-)

applied to u-boot-x86/master, thanks!

#44 lore raw

PATCH v2 18/55 x86: ivybridge: Use common CPU init code

In reply to Simon Glass

The existing ivybridge code predates the normal multi-core CPU init, and it is not used. Remove it and add CPU nodes to the device tree so that all four CPUs are set up. Also enable the 'cpu' command.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 94 ++++++++++++++++--------------------
 arch/x86/dts/chromebook_link.dts     | 34 +++++++++++++
 configs/chromebook_link_defconfig    |  3 ++
 3 files changed, 79 insertions(+), 52 deletions(-)
arch/x86/cpu/ivybridge/model_206ax.c +42 -52
index fd7db97..9fa1226 100644
@@ -8,10 +8,13 @@
  */
 
 #include <common.h>
+#include <cpu.h>
+#include <dm.h>
 #include <fdtdec.h>
 #include <malloc.h>
 #include <asm/acpi.h>
 #include <asm/cpu.h>
+#include <asm/cpu_x86.h>
 #include <asm/lapic.h>
 #include <asm/msr.h>
 #include <asm/mtrr.h>
@@ -400,55 +403,6 @@ static void configure_mca(void)
 static unsigned ehci_debug_addr;
 #endif
 
-/*
- * Initialize any extra cores/threads in this package.
- */
-static int intel_cores_init(struct x86_cpu_priv *cpu)
-{
-	struct cpuid_result result;
-	unsigned threads_per_package, threads_per_core, i;
-
-	/* Logical processors (threads) per core */
-	result = cpuid_ext(0xb, 0);
-	threads_per_core = result.ebx & 0xffff;
-
-	/* Logical processors (threads) per package */
-	result = cpuid_ext(0xb, 1);
-	threads_per_package = result.ebx & 0xffff;
-
-	debug("CPU: %u has %u cores, %u threads per core\n",
-	      cpu->apic_id, threads_per_package / threads_per_core,
-	      threads_per_core);
-
-	for (i = 1; i < threads_per_package; ++i) {
-		struct x86_cpu_priv *new_cpu;
-
-		new_cpu = calloc(1, sizeof(*new_cpu));
-		if (!new_cpu)
-			return -ENOMEM;
-
-		new_cpu->apic_id = cpu->apic_id + i;
-
-		/* Update APIC ID if no hyperthreading */
-		if (threads_per_core == 1)
-			new_cpu->apic_id <<= 1;
-
-		debug("CPU: %u has core %u\n", cpu->apic_id, new_cpu->apic_id);
-
-#if 0 && CONFIG_SMP && CONFIG_MAX_CPUS > 1
-		/* TODO(sjg at chromium.org): Start the new cpu */
-		if (!start_cpu(new_cpu)) {
-			/* Record the error in cpu? */
-			printk(BIOS_ERR, "CPU %u would not start!\n",
-			       new_cpu->apic_id);
-			new_cpu->start_err = 1;
-		}
-#endif
-	}
-
-	return 0;
-}
-
 int model_206ax_init(struct x86_cpu_priv *cpu)
 {
 	int ret;
@@ -492,8 +446,10 @@ int model_206ax_init(struct x86_cpu_priv *cpu)
 
 	/* Thermal throttle activation offset */
 	ret = configure_thermal_target();
-	if (ret)
+	if (ret) {
+		debug("Cannot set thermal target\n");
 		return ret;
+	}
 
 	/* Enable Direct Cache Access */
 	configure_dca_cap();
@@ -507,8 +463,42 @@ int model_206ax_init(struct x86_cpu_priv *cpu)
 	/* Enable Turbo */
 	turbo_enable();
 
-	/* Start up extra cores */
-	intel_cores_init(cpu);
+	return 0;
+}
+
+static int model_206ax_get_info(struct udevice *dev, struct cpu_info *info)
+{
+	info->features = 1 << CPU_FEAT_L1_CACHE | 1 << CPU_FEAT_MMU;
+
+	return 0;
+}
+
+static int model_206ax_get_count(struct udevice *dev)
+{
+	return 4;
+}
 
+static int cpu_x86_model_206ax_probe(struct udevice *dev)
+{
 	return 0;
 }
+
+static const struct cpu_ops cpu_x86_model_206ax_ops = {
+	.get_desc	= cpu_x86_get_desc,
+	.get_info	= model_206ax_get_info,
+	.get_count	= model_206ax_get_count,
+};
+
+static const struct udevice_id cpu_x86_model_206ax_ids[] = {
+	{ .compatible = "intel,core-gen3" },
+	{ }
+};
+
+U_BOOT_DRIVER(cpu_x86_model_206ax_drv) = {
+	.name		= "cpu_x86_model_206ax",
+	.id		= UCLASS_CPU,
+	.of_match	= cpu_x86_model_206ax_ids,
+	.bind		= cpu_x86_bind,
+	.probe		= cpu_x86_model_206ax_probe,
+	.ops		= &cpu_x86_model_206ax_ops,
+};
arch/x86/dts/chromebook_link.dts +34 -0
index e2c722d..3ed6662 100644
@@ -18,6 +18,40 @@
 	       silent_console = <0>;
 	};
 
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "intel,core-gen3";
+			reg = <0>;
+			intel,apic-id = <0>;
+		};
+
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "intel,core-gen3";
+			reg = <1>;
+			intel,apic-id = <1>;
+		};
+
+		cpu at 2 {
+			device_type = "cpu";
+			compatible = "intel,core-gen3";
+			reg = <2>;
+			intel,apic-id = <2>;
+		};
+
+		cpu at 3 {
+			device_type = "cpu";
+			compatible = "intel,core-gen3";
+			reg = <3>;
+			intel,apic-id = <3>;
+		};
+
+	};
+
 	gpioa {
 		compatible = "intel,ich6-gpio";
 		u-boot,dm-pre-reloc;
configs/chromebook_link_defconfig +3 -0
index dbfbb97..06e4ce6 100644
@@ -5,7 +5,9 @@ CONFIG_DEFAULT_DEVICE_TREE="chromebook_link"
 CONFIG_TARGET_CHROMEBOOK_LINK=y
 CONFIG_HAVE_MRC=y
 CONFIG_ENABLE_MRC_CACHE=y
+CONFIG_SMP=y
 CONFIG_HAVE_VGA_BIOS=y
+CONFIG_CMD_CPU=y
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
@@ -17,6 +19,7 @@ CONFIG_CMD_BOOTSTAGE=y
 CONFIG_CMD_TPM=y
 CONFIG_CMD_TPM_TEST=y
 CONFIG_OF_CONTROL=y
+CONFIG_CPU=y
 CONFIG_CMD_CROS_EC=y
 CONFIG_CROS_EC=y
 CONFIG_CROS_EC_LPC=y
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#45 lore raw

PATCH v2 18/55 x86: ivybridge: Use common CPU init code

Quoted 6 lines · Simon Glass

The existing ivybridge code predates the normal multi-core CPU init, and it is not used. Remove it and add CPU nodes to the device tree so that all four CPUs are set up. Also enable the 'cpu' command.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 94 ++++++++++++++++--------------------
 arch/x86/dts/chromebook_link.dts     | 34 +++++++++++++
 configs/chromebook_link_defconfig    |  3 ++
 3 files changed, 79 insertions(+), 52 deletions(-)

applied to u-boot-x86/master, thanks!

#46 lore raw

PATCH v2 19/55 x86: ivybridge: Move CPU init code into the driver

In reply to Simon Glass

Use the CPU driver's probe() method to perform the CPU init. This will happen automatically when the first CPU is probed.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              |  6 ------
 arch/x86/cpu/ivybridge/model_206ax.c          |  5 ++++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h | 15 ---------------
 3 files changed, 4 insertions(+), 22 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -6
index c71596d..149c1d2 100644
@@ -61,7 +61,6 @@ static int bd82x6x_probe(struct udevice *dev)
 {
 	const void *blob = gd->fdt_blob;
 	struct pci_controller *hose;
-	struct x86_cpu_priv *cpu;
 	int sata_node, gma_node;
 	int ret;
 
@@ -81,11 +80,6 @@ static int bd82x6x_probe(struct udevice *dev)
 	bd82x6x_usb_ehci_init(PCH_EHCI1_DEV);
 	bd82x6x_usb_ehci_init(PCH_EHCI2_DEV);
 
-	cpu = calloc(1, sizeof(*cpu));
-	if (!cpu)
-		return -ENOMEM;
-	model_206ax_init(cpu);
-
 	gma_node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_GMA);
 	if (gma_node < 0) {
 		debug("%s: Cannot find GMA node\n", __func__);
arch/x86/cpu/ivybridge/model_206ax.c +4 -1
index 9fa1226..6ab6ede 100644
@@ -403,7 +403,7 @@ static void configure_mca(void)
 static unsigned ehci_debug_addr;
 #endif
 
-int model_206ax_init(struct x86_cpu_priv *cpu)
+static int model_206ax_init(void)
 {
 	int ret;
 
@@ -480,6 +480,9 @@ static int model_206ax_get_count(struct udevice *dev)
 
 static int cpu_x86_model_206ax_probe(struct udevice *dev)
 {
+	if (dev->seq == 0)
+		model_206ax_init();
+
 	return 0;
 }
 
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -15
index d76cb8d..fc7fc6d 100644
@@ -15,19 +15,4 @@ void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
 int bd82x6x_init_extra(void);
 
-/**
- * struct x86_cpu_priv - Information about a single CPU
- *
- * @apic_id: Advanced Programmable Interrupt Controller Identifier, which is
- * just a number representing the CPU core
- *
- * TODO: Move this to driver model once lifecycle is understood
- */
-struct x86_cpu_priv {
-	int apic_id;
-	int start_err;
-};
-
-int model_206ax_init(struct x86_cpu_priv *cpu);
-
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#47 lore raw

PATCH v2 19/55 x86: ivybridge: Move CPU init code into the driver

Quoted 5 lines · Simon Glass

Use the CPU driver's probe() method to perform the CPU init. This will happen automatically when the first CPU is probed.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              |  6 ------
 arch/x86/cpu/ivybridge/model_206ax.c          |  5 ++++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h | 15 ---------------
 3 files changed, 4 insertions(+), 22 deletions(-)

applied to u-boot-x86/master, thanks!

#48 lore raw

PATCH v2 20/55 x86: ivybridge: Set up the thermal target correctly

In reply to Simon Glass

This uses a non-existent node at present. It should use the first CPU node. The referenced property does not exist (the correct value is the default of 0), but this allows the follow-on init to complete.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)
arch/x86/cpu/ivybridge/model_206ax.c +10 -11
index 6ab6ede..a217954 100644
@@ -283,18 +283,13 @@ static void configure_c_states(void)
 	msr_write(MSR_PP1_CURRENT_CONFIG, msr);
 }
 
-static int configure_thermal_target(void)
+static int configure_thermal_target(struct udevice *dev)
 {
 	int tcc_offset;
 	msr_t msr;
-	int node;
 
-	/* Find pointer to CPU configuration */
-	node = fdtdec_next_compatible(gd->fdt_blob, 0,
-				      COMPAT_INTEL_MODEL_206AX);
-	if (node < 0)
-		return -ENOENT;
-	tcc_offset = fdtdec_get_int(gd->fdt_blob, node, "tcc-offset", 0);
+	tcc_offset = fdtdec_get_int(gd->fdt_blob, dev->of_offset, "tcc-offset",
+				    0);
 
 	/* Set TCC activaiton offset if supported */
 	msr = msr_read(MSR_PLATFORM_INFO);
@@ -403,7 +398,7 @@ static void configure_mca(void)
 static unsigned ehci_debug_addr;
 #endif
 
-static int model_206ax_init(void)
+static int model_206ax_init(struct udevice *dev)
 {
 	int ret;
 
@@ -445,7 +440,7 @@ static int model_206ax_init(void)
 	configure_misc();
 
 	/* Thermal throttle activation offset */
-	ret = configure_thermal_target();
+	ret = configure_thermal_target(dev);
 	if (ret) {
 		debug("Cannot set thermal target\n");
 		return ret;
@@ -468,6 +463,10 @@ static int model_206ax_init(void)
 
 static int model_206ax_get_info(struct udevice *dev, struct cpu_info *info)
 {
+	msr_t msr;
+
+	msr = msr_read(IA32_PERF_CTL);
+	info->cpu_freq = ((msr.lo >> 8) & 0xff) * SANDYBRIDGE_BCLK * 1000000;
 	info->features = 1 << CPU_FEAT_L1_CACHE | 1 << CPU_FEAT_MMU;
 
 	return 0;
@@ -481,7 +480,7 @@ static int model_206ax_get_count(struct udevice *dev)
 static int cpu_x86_model_206ax_probe(struct udevice *dev)
 {
 	if (dev->seq == 0)
-		model_206ax_init();
+		model_206ax_init(dev);
 
 	return 0;
 }
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#49 lore raw

PATCH v2 20/55 x86: ivybridge: Set up the thermal target correctly

Quoted 4 lines · Simon Glass

This uses a non-existent node at present. It should use the first CPU node. The referenced property does not exist (the correct value is the default of 0), but this allows the follow-on init to complete.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)

applied to u-boot-x86/master, thanks!

#50 lore raw

PATCH v2 21/55 x86: ivybridge: Drop the dead MTRR code

In reply to Simon Glass

This is not used and MTRRs are set up elsewhere now. Drop it.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 10 ----------
 1 file changed, 10 deletions(-)
arch/x86/cpu/ivybridge/model_206ax.c +0 -10
index a217954..9654600 100644
@@ -412,16 +412,6 @@ static int model_206ax_init(struct udevice *dev)
 	set_ehci_debug(0);
 #endif
 
-	/* Setup MTRRs based on physical address size */
-#if 0 /* TODO: Implement this */
-	struct cpuid_result cpuid_regs;
-
-	cpuid_regs = cpuid(0x80000008);
-	x86_setup_fixed_mtrrs();
-	x86_setup_var_mtrrs(cpuid_regs.eax & 0xff, 2);
-	x86_mtrr_check();
-#endif
-
 #if CONFIG_USBDEBUG
 	set_ehci_debug(ehci_debug_addr);
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#51 lore raw

PATCH v2 21/55 x86: ivybridge: Drop the dead MTRR code

Quoted 11 lines · Simon Glass

This is not used and MTRRs are set up elsewhere now. Drop it.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/model_206ax.c | 10 ----------
 1 file changed, 10 deletions(-)

applied to u-boot-x86/master, thanks!

#52 lore raw

PATCH v2 22/55 x86: ivybridge: Move early init code into northbridge.c

In reply to Simon Glass

This code is now part of the northbridge driver, so move it into the same place.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile      |  1 -
 arch/x86/cpu/ivybridge/early_init.c  | 81 ------------------------------------
 arch/x86/cpu/ivybridge/northbridge.c | 67 +++++++++++++++++++++++++++++
 3 files changed, 67 insertions(+), 82 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/early_init.c
arch/x86/cpu/ivybridge/Makefile +0 -1
index 0c7efae..bdbd3fa 100644
@@ -7,7 +7,6 @@
 obj-y += bd82x6x.o
 obj-y += car.o
 obj-y += cpu.o
-obj-y += early_init.o
 obj-y += early_me.o
 obj-y += gma.o
 obj-y += lpc.o
arch/x86/cpu/ivybridge/early_init.c deleted +0 -81

81 lines not on this page · raw message

arch/x86/cpu/ivybridge/northbridge.c +67 -0

76 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#53 lore raw

PATCH v2 22/55 x86: ivybridge: Move early init code into northbridge.c

Quoted 7 lines · Simon Glass

This code is now part of the northbridge driver, so move it into the same place.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile      |  1 -
 arch/x86/cpu/ivybridge/early_init.c  | 81 ------------------------------------
 arch/x86/cpu/ivybridge/northbridge.c | 67 +++++++++++++++++++++++++++++
 3 files changed, 67 insertions(+), 82 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/early_init.c

applied to u-boot-x86/master, thanks!

#54 lore raw

PATCH v2 23/55 x86: Make x86_init_cpus() static

In reply to Simon Glass

There are no other implementations of this function, and boards that need it can implement a CPU driver.

---

Changes in v2:
- Fix 'baords' typo in the commit message

 arch/x86/cpu/cpu.c                | 2 +-
 arch/x86/include/asm/u-boot-x86.h | 2 --
 2 files changed, 1 insertion(+), 3 deletions(-)
arch/x86/cpu/cpu.c +1 -1
index 381d835..3c812e9 100644
@@ -688,7 +688,7 @@ static int x86_mp_init(void)
 }
 #endif
 
-__weak int x86_init_cpus(void)
+static int x86_init_cpus(void)
 {
 #ifdef CONFIG_SMP
 	debug("Init additional CPUs\n");
arch/x86/include/asm/u-boot-x86.h +0 -2
index dbf8e95..9c143ca 100644
@@ -77,8 +77,6 @@ uint64_t timer_get_tsc(void);
 
 void quick_ram_check(void);
 
-int x86_init_cpus(void);
-
 #define PCI_VGA_RAM_IMAGE_START		0xc0000
 
 #endif	/* _U_BOOT_I386_H_ */
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#55 lore raw

PATCH v2 23/55 x86: Make x86_init_cpus() static

Quoted 5 lines · Simon Glass

There are no other implementations of this function, and boards that need it can implement a CPU driver.

Quoted 9 lines

---

Changes in v2:
- Fix 'baords' typo in the commit message

 arch/x86/cpu/cpu.c                | 2 +-
 arch/x86/include/asm/u-boot-x86.h | 2 --
 2 files changed, 1 insertion(+), 3 deletions(-)

applied to u-boot-x86/master, thanks!

#56 lore raw

PATCH v2 24/55 x86: Don't show an error when the MRC cache is up to date

In reply to Simon Glass

When the final MRC cache record is the same as the one we want to write, we skip writing since there is no point. This is normal behaviour.

Avoiding printing an error when this happens.

---

Changes in v2: None

 arch/x86/lib/mrccache.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
arch/x86/lib/mrccache.c +5 -1
index 53a1259..67bace4 100644
@@ -243,8 +243,12 @@ int mrccache_save(void)
 		goto err_entry;
 	data  = (struct mrc_data_container *)gd->arch.mrc_output;
 	ret = mrccache_update(sf, &entry, data);
-	if (!ret)
+	if (!ret) {
 		debug("Saved MRC data with checksum %04x\n", data->checksum);
+	} else if (ret == -EEXIST) {
+		debug("MRC data is the same as last time, skipping save\n");
+		ret = 0;
+	}
 
 err_entry:
 	if (ret)
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#57 lore raw

PATCH v2 24/55 x86: Don't show an error when the MRC cache is up to date

Quoted 5 lines · Simon Glass

When the final MRC cache record is the same as the one we want to write, we skip writing since there is no point. This is normal behaviour.

Avoiding printing an error when this happens.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/lib/mrccache.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

applied to u-boot-x86/master, thanks!

#58 lore raw

PATCH v2 25/55 x86: Bring up northbridge, pch and lpc after the CPUs

In reply to Simon Glass

These devices currently need to be inited early in boot. Once we have the init in the right places (with each device doing its own init and no problems with ordering) we should be able to remove this. For now it is needed to keep things working.

---

Changes in v2:
- Add a comment as to why we are initing the devices again

 arch/x86/cpu/cpu.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)
arch/x86/cpu/cpu.c +18 -2
index 3c812e9..6c3a748 100644
@@ -709,8 +709,24 @@ static int x86_init_cpus(void)
 
 int cpu_init_r(void)
 {
-	if (ll_boot_init())
-		return x86_init_cpus();
+	struct udevice *dev;
+	int ret;
+
+	if (!ll_boot_init())
+		return 0;
+
+	ret = x86_init_cpus();
+	if (ret)
+		return ret;
+
+	/*
+	 * Set up the northbridge, PCH and LPC if available. Note that these
+	 * may have had some limited pre-relocation init if they were probed
+	 * before relocation, but this is post relocation.
+	 */
+	uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
+	uclass_first_device(UCLASS_PCH, &dev);
+	uclass_first_device(UCLASS_LPC, &dev);
 
 	return 0;
 }
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#59 lore raw

PATCH v2 25/55 x86: Bring up northbridge, pch and lpc after the CPUs

Quoted 5 lines · Simon Glass

These devices currently need to be inited early in boot. Once we have the init in the right places (with each device doing its own init and no problems with ordering) we should be able to remove this. For now it is needed to keep things working.

Quoted 9 lines

---

Changes in v2:
- Add a comment as to why we are initing the devices again

 arch/x86/cpu/cpu.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)
#60 lore raw

PATCH v2 25/55 x86: Bring up northbridge, pch and lpc after the CPUs

Quoted 9 lines · Bin Meng
Quoted 8 lines · Simon Glass

These devices currently need to be inited early in boot. Once we have the init in the right places (with each device doing its own init and no problems with ordering) we should be able to remove this. For now it is needed to keep things working.

---

Quoted 8 lines
Quoted 6 lines

Changes in v2:
- Add a comment as to why we are initing the devices again

 arch/x86/cpu/cpu.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

applied to u-boot-x86/master, thanks!

#61 lore raw

PATCH v2 26/55 x86: ivybridge: Move northbridge and PCH init into drivers

In reply to Simon Glass

Instead of calling the northbridge and PCH init from bd82x6x_init_extra() when the PCI bus is probed, call it from the respective drivers. Also drop the Northbridge init as it has no effect. The registers it touches appear to be read-only.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              | 42 ---------------------------
 arch/x86/cpu/ivybridge/northbridge.c          | 16 +++++++---
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 board/google/chromebook_link/link.c           |  8 -----
 4 files changed, 12 insertions(+), 55 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -42
index 149c1d2..c5a5d4d 100644
@@ -18,45 +18,6 @@
 
 #define BIOS_CTRL	0xdc
 
-void bd82x6x_pci_init(pci_dev_t dev)
-{
-	u16 reg16;
-	u8 reg8;
-
-	debug("bd82x6x PCI init.\n");
-	/* Enable Bus Master */
-	reg16 = x86_pci_read_config16(dev, PCI_COMMAND);
-	reg16 |= PCI_COMMAND_MASTER;
-	x86_pci_write_config16(dev, PCI_COMMAND, reg16);
-
-	/* This device has no interrupt */
-	x86_pci_write_config8(dev, INTR, 0xff);
-
-	/* disable parity error response and SERR */
-	reg16 = x86_pci_read_config16(dev, BCTRL);
-	reg16 &= ~(1 << 0);
-	reg16 &= ~(1 << 1);
-	x86_pci_write_config16(dev, BCTRL, reg16);
-
-	/* Master Latency Count must be set to 0x04! */
-	reg8 = x86_pci_read_config8(dev, SMLT);
-	reg8 &= 0x07;
-	reg8 |= (0x04 << 3);
-	x86_pci_write_config8(dev, SMLT, reg8);
-
-	/* Will this improve throughput of bus masters? */
-	x86_pci_write_config8(dev, PCI_MIN_GNT, 0x06);
-
-	/* Clear errors in status registers */
-	reg16 = x86_pci_read_config16(dev, PSTS);
-	/* reg16 |= 0xf900; */
-	x86_pci_write_config16(dev, PSTS, reg16);
-
-	reg16 = x86_pci_read_config16(dev, SECSTS);
-	/* reg16 |= 0xf900; */
-	x86_pci_write_config16(dev, SECSTS, reg16);
-}
-
 static int bd82x6x_probe(struct udevice *dev)
 {
 	const void *blob = gd->fdt_blob;
@@ -108,10 +69,7 @@ int bd82x6x_init_extra(void)
 		return -EINVAL;
 	}
 
-	bd82x6x_pci_init(PCH_DEV);
 	bd82x6x_sata_enable(PCH_SATA_DEV, blob, sata_node);
-	northbridge_enable(PCH_DEV);
-	northbridge_init(PCH_DEV);
 
 	return 0;
 }
arch/x86/cpu/ivybridge/northbridge.c +12 -4
index 6b00d31..2eed0af 100644
@@ -197,15 +197,12 @@ static void sandybridge_setup_northbridge_bars(struct udevice *dev)
 	dm_pci_write_config8(dev, PAM6, 0x33);
 }
 
-static int bd82x6x_northbridge_probe(struct udevice *dev)
+static int bd82x6x_northbridge_early_init(struct udevice *dev)
 {
 	const int chipset_type = SANDYBRIDGE_MOBILE;
 	u32 capid0_a;
 	u8 reg8;
 
-	if (gd->flags & GD_FLG_RELOC)
-		return 0;
-
 	/* Device ID Override Enable should be done very early */
 	dm_pci_read_config32(dev, 0xe4, &capid0_a);
 	if (capid0_a & (1 << 10)) {
@@ -226,6 +223,17 @@ static int bd82x6x_northbridge_probe(struct udevice *dev)
 	return 0;
 }
 
+static int bd82x6x_northbridge_probe(struct udevice *dev)
+{
+	if (!(gd->flags & GD_FLG_RELOC))
+		return bd82x6x_northbridge_early_init(dev);
+
+	northbridge_enable(PCH_DEV);
+	northbridge_init(PCH_DEV);
+
+	return 0;
+}
+
 static const struct udevice_id bd82x6x_northbridge_ids[] = {
 	{ .compatible = "intel,bd82x6x-northbridge" },
 	{ }
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index fc7fc6d..0f4fe47 100644
@@ -9,7 +9,6 @@
 
 void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node);
 void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node);
-void bd82x6x_pci_init(pci_dev_t dev);
 void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
board/google/chromebook_link/link.c +0 -8
index 1b97a8f..d12d742 100644
@@ -14,14 +14,6 @@
 
 int arch_early_init_r(void)
 {
-	struct udevice *dev;
-	int ret;
-
-	/* Make sure the platform controller hub is up and running */
-	ret = uclass_get_device(UCLASS_PCH, 0, &dev);
-	if (ret)
-		return ret;
-
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#62 lore raw

PATCH v2 26/55 x86: ivybridge: Move northbridge and PCH init into drivers

Quoted 8 lines · Simon Glass

Instead of calling the northbridge and PCH init from bd82x6x_init_extra() when the PCI bus is probed, call it from the respective drivers. Also drop the Northbridge init as it has no effect. The registers it touches appear to be read-only.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              | 42 ---------------------------
 arch/x86/cpu/ivybridge/northbridge.c          | 16 +++++++---
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 board/google/chromebook_link/link.c           |  8 -----
 4 files changed, 12 insertions(+), 55 deletions(-)
#63 lore raw

PATCH v2 26/55 x86: ivybridge: Move northbridge and PCH init into drivers

Quoted 11 lines · Bin Meng
Quoted 10 lines · Simon Glass

Instead of calling the northbridge and PCH init from bd82x6x_init_extra() when the PCI bus is probed, call it from the respective drivers. Also drop the Northbridge init as it has no effect. The registers it touches appear to be read-only.

---

Changes in v2: None

Quoted 8 lines
Quoted 6 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              | 42 ---------------------------
 arch/x86/cpu/ivybridge/northbridge.c          | 16 +++++++---
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 board/google/chromebook_link/link.c           |  8 -----
 4 files changed, 12 insertions(+), 55 deletions(-)

applied to u-boot-x86/master, thanks!

#64 lore raw

PATCH v2 27/55 x86: ivybridge: Use driver model PCI API in bd82x6x.c

In reply to Simon Glass

Adjust most of the remaining functions in this file to use the driver model PCI API. The one remaining function is bridge_silicon_revision() which will need a little more work.

---

Changes in v2:
- Drop northbridge_enable()

 arch/x86/cpu/ivybridge/northbridge.c              | 20 +++++++-------------
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  3 ---
 2 files changed, 7 insertions(+), 16 deletions(-)
arch/x86/cpu/ivybridge/northbridge.c +7 -13
index 2eed0af..d52eb39 100644
@@ -48,15 +48,14 @@ int bridge_silicon_revision(void)
 static const int legacy_hole_base_k = 0xa0000 / 1024;
 static const int legacy_hole_size_k = 384;
 
-static int get_pcie_bar(u32 *base, u32 *len)
+static int get_pcie_bar(struct udevice *dev, u32 *base, u32 *len)
 {
-	pci_dev_t dev = PCI_BDF(0, 0, 0);
 	u32 pciexbar_reg;
 
 	*base = 0;
 	*len = 0;
 
-	pciexbar_reg = x86_pci_read_config32(dev, PCIEXBAR);
+	dm_pci_read_config32(dev, PCIEXBAR, &pciexbar_reg);
 
 	if (!(pciexbar_reg & (1 << 0)))
 		return 0;
@@ -82,17 +81,17 @@ static int get_pcie_bar(u32 *base, u32 *len)
 	return 0;
 }
 
-static void add_fixed_resources(pci_dev_t dev, int index)
+static void add_fixed_resources(struct udevice *dev, int index)
 {
 	u32 pcie_config_base, pcie_config_size;
 
-	if (get_pcie_bar(&pcie_config_base, &pcie_config_size)) {
+	if (get_pcie_bar(dev, &pcie_config_base, &pcie_config_size)) {
 		debug("Adding PCIe config bar base=0x%08x size=0x%x\n",
 		      pcie_config_base, pcie_config_size);
 	}
 }
 
-static void northbridge_dmi_init(pci_dev_t dev)
+static void northbridge_dmi_init(struct udevice *dev)
 {
 	/* Clear error status bits */
 	writel(0xffffffff, DMIBAR_REG(0x1c4));
@@ -120,7 +119,7 @@ static void northbridge_dmi_init(pci_dev_t dev)
 	setbits_le32(DMIBAR_REG(0x88), (1 << 1) | (1 << 0));
 }
 
-void northbridge_init(pci_dev_t dev)
+static void northbridge_init(struct udevice *dev)
 {
 	u32 bridge_type;
 
@@ -168,10 +167,6 @@ void northbridge_init(pci_dev_t dev)
 	writel(0x00100001, MCHBAR_REG(0x5500));
 }
 
-void northbridge_enable(pci_dev_t dev)
-{
-}
-
 static void sandybridge_setup_northbridge_bars(struct udevice *dev)
 {
 	/* Set up all hardcoded northbridge BARs */
@@ -228,8 +223,7 @@ static int bd82x6x_northbridge_probe(struct udevice *dev)
 	if (!(gd->flags & GD_FLG_RELOC))
 		return bd82x6x_northbridge_early_init(dev);
 
-	northbridge_enable(PCH_DEV);
-	northbridge_init(PCH_DEV);
+	northbridge_init(dev);
 
 	return 0;
 }
arch/x86/include/asm/arch-ivybridge/sandybridge.h +0 -3
index c960525..af8a9f7 100644
@@ -110,9 +110,6 @@
 
 int bridge_silicon_revision(void);
 
-void northbridge_enable(pci_dev_t dev);
-void northbridge_init(pci_dev_t dev);
-
 void report_platform_info(void);
 
 void sandybridge_early_init(int chipset_type);
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#65 lore raw

PATCH v2 27/55 x86: ivybridge: Use driver model PCI API in bd82x6x.c

Quoted 6 lines · Simon Glass

Adjust most of the remaining functions in this file to use the driver model PCI API. The one remaining function is bridge_silicon_revision() which will need a little more work.

Quoted 9 lines

---

Changes in v2:
- Drop northbridge_enable()

 arch/x86/cpu/ivybridge/northbridge.c              | 20 +++++++-------------
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  3 ---
 2 files changed, 7 insertions(+), 16 deletions(-)

applied to u-boot-x86/master, thanks!

#66 lore raw

PATCH v2 28/55 x86: ivybridge: Drop unnecessary northbridge setup

In reply to Simon Glass

This is done by default with PCI auto-config. Drop it.

---

Changes in v2:
- Rename from 'Move northbridge setup to the northbridge driver'
- Drop this unnecessary init

 arch/x86/cpu/ivybridge/pci.c | 20 --------------------
 1 file changed, 20 deletions(-)
arch/x86/cpu/ivybridge/pci.c +0 -20
index 8af99b4..b081469 100644
@@ -19,32 +19,12 @@
 
 static int pci_ivybridge_probe(struct udevice *bus)
 {
-	struct pci_controller *hose = dev_get_uclass_priv(bus);
-	pci_dev_t dev;
-	u16 reg16;
-
 	if (!(gd->flags & GD_FLG_RELOC))
 		return 0;
 	post_code(0x50);
 	bd82x6x_init_extra();
 	post_code(0x51);
 
-	reg16 = 0xff;
-	dev = PCH_DEV;
-	reg16 = x86_pci_read_config16(dev, PCI_COMMAND);
-	reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
-	x86_pci_write_config16(dev, PCI_COMMAND, reg16);
-
-	/*
-	* Clear non-reserved bits in status register.
-	*/
-	pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
-	pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
-	pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
-
-	pci_write_bar32(hose, dev, 0, 0xf0000000);
-	post_code(0x52);
-
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#67 lore raw

PATCH v2 28/55 x86: ivybridge: Drop unnecessary northbridge setup

Quoted 12 lines · Simon Glass

This is done by default with PCI auto-config. Drop it.

---

Changes in v2:
- Rename from 'Move northbridge setup to the northbridge driver'
- Drop this unnecessary init

 arch/x86/cpu/ivybridge/pci.c | 20 --------------------
 1 file changed, 20 deletions(-)
#68 lore raw

PATCH v2 28/55 x86: ivybridge: Drop unnecessary northbridge setup

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

This is done by default with PCI auto-config. Drop it.

---

Changes in v2:
- Rename from 'Move northbridge setup to the northbridge driver'
- Drop this unnecessary init

Quoted 5 lines
Quoted 3 lines
 arch/x86/cpu/ivybridge/pci.c | 20 --------------------
 1 file changed, 20 deletions(-)

applied to u-boot-x86/master, thanks!

#69 lore raw

PATCH v2 29/55 ahci: Add a disk-controller uclass

In reply to Simon Glass

Add a uclass ID for a disk controller. This can be used by AHCI/SATA or other controller types. There are no operations and no interface so far, but it is possible to probe a SATA device.

---

Changes in v2:
- Rename the AHCI uclass to DISK

 drivers/block/Kconfig       |  9 +++++++++
 drivers/block/Makefile      |  1 +
 drivers/block/disk-uclass.c | 14 ++++++++++++++
 include/dm/uclass-id.h      |  1 +
 4 files changed, 25 insertions(+)
 create mode 100644 drivers/block/disk-uclass.c
drivers/block/Kconfig +9 -0
index e69de29..989b21d 100644
@@ -0,0 +1,9 @@
+config DISK
+	bool "Support disk controllers with driver model"
+	depends on DM
+	default y if DM
+	help
+	  This enables a uclass for disk controllers  in U-Boot. Various driver
+	  types can use this, such as AHCI/SATA. It does not provide any standard
+	  operations at present. The block device interface has not been converted
+	  to driver model.
drivers/block/Makefile +1 -0
index eb8bda9..5eb87e0 100644
@@ -5,6 +5,7 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+obj-$(CONFIG_DISK) += disk-uclass.o
 obj-$(CONFIG_SCSI_AHCI) += ahci.o
 obj-$(CONFIG_DWC_AHSATA) += dwc_ahsata.o
 obj-$(CONFIG_FSL_SATA) += fsl_sata.o
drivers/block/disk-uclass.c new file +14 -0
new file mode 100644
index 0000000..d665b35
@@ -0,0 +1,14 @@
+/*
+ * Copyright (c) 2015 Google, Inc
+ * Written by Simon Glass <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+
+UCLASS_DRIVER(disk) = {
+	.id		= UCLASS_DISK,
+	.name		= "disk",
+};
include/dm/uclass-id.h +1 -0
index 4a6827b..2e10953 100644
@@ -29,6 +29,7 @@ enum uclass_id {
 	UCLASS_CLK,		/* Clock source, e.g. used by peripherals */
 	UCLASS_CPU,		/* CPU, typically part of an SoC */
 	UCLASS_CROS_EC,		/* Chrome OS EC */
+	UCLASS_DISK,		/* Disk controller, e.g. SATA */
 	UCLASS_DISPLAY_PORT,	/* Display port video */
 	UCLASS_RAM,		/* RAM controller */
 	UCLASS_ETH,		/* Ethernet device */
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#70 lore raw

PATCH v2 29/55 ahci: Add a disk-controller uclass

Quoted 22 lines · Simon Glass

Add a uclass ID for a disk controller. This can be used by AHCI/SATA or other controller types. There are no operations and no interface so far, but it is possible to probe a SATA device.

---

Changes in v2:
- Rename the AHCI uclass to DISK

 drivers/block/Kconfig       |  9 +++++++++
 drivers/block/Makefile      |  1 +
 drivers/block/disk-uclass.c | 14 ++++++++++++++
 include/dm/uclass-id.h      |  1 +
 4 files changed, 25 insertions(+)
 create mode 100644 drivers/block/disk-uclass.c
drivers/block/Kconfig +0 -0
index e69de29..989b21d 100644

drivers/block/Kconfig line 6

Quoted 6 lines
drivers/block/Kconfig +6 -0
@@ -0,0 +1,9 @@
+config DISK
+       bool "Support disk controllers with driver model"
+       depends on DM
+       default y if DM
+       help
+         This enables a uclass for disk controllers  in U-Boot. Various driver

nits: one more space before "in U-Boot"

I can fix this when applying.

Quoted 40 lines
drivers/block/Kconfig +3 -0
+         types can use this, such as AHCI/SATA. It does not provide any standard
+         operations at present. The block device interface has not been converted
+         to driver model.
drivers/block/Makefile +1 -0
index eb8bda9..5eb87e0 100644
@@ -5,6 +5,7 @@
 # SPDX-License-Identifier:     GPL-2.0+
 #
 
+obj-$(CONFIG_DISK) += disk-uclass.o
 obj-$(CONFIG_SCSI_AHCI) += ahci.o
 obj-$(CONFIG_DWC_AHSATA) += dwc_ahsata.o
 obj-$(CONFIG_FSL_SATA) += fsl_sata.o
drivers/block/disk-uclass.c new file +14 -0
new file mode 100644
index 0000000..d665b35
@@ -0,0 +1,14 @@
+/*
+ * Copyright (c) 2015 Google, Inc
+ * Written by Simon Glass <[email protected]>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+
+UCLASS_DRIVER(disk) = {
+       .id             = UCLASS_DISK,
+       .name           = "disk",
+};
include/dm/uclass-id.h +0 -0
index 4a6827b..2e10953 100644

include/dm/uclass-id.h enum uclass_id {

Quoted 8 lines
include/dm/uclass-id.h +1 -1
@@ -29,6 +29,7 @@ enum uclass_id {
        UCLASS_CLK,             /* Clock source, e.g. used by peripherals */
        UCLASS_CPU,             /* CPU, typically part of an SoC */
        UCLASS_CROS_EC,         /* Chrome OS EC */
+       UCLASS_DISK,            /* Disk controller, e.g. SATA */
        UCLASS_DISPLAY_PORT,    /* Display port video */
        UCLASS_RAM,             /* RAM controller */
        UCLASS_ETH,             /* Ethernet device */
--
#71 lore raw

PATCH v2 29/55 ahci: Add a disk-controller uclass

Quoted 32 lines · Bin Meng
Quoted 22 lines · Simon Glass

Add a uclass ID for a disk controller. This can be used by AHCI/SATA or other controller types. There are no operations and no interface so far, but it is possible to probe a SATA device.

---

Changes in v2:
- Rename the AHCI uclass to DISK

 drivers/block/Kconfig       |  9 +++++++++
 drivers/block/Makefile      |  1 +
 drivers/block/disk-uclass.c | 14 ++++++++++++++
 include/dm/uclass-id.h      |  1 +
 4 files changed, 25 insertions(+)
 create mode 100644 drivers/block/disk-uclass.c
drivers/block/Kconfig +0 -0
index e69de29..989b21d 100644

drivers/block/Kconfig line 6

Quoted 6 lines
drivers/block/Kconfig +6 -0
@@ -0,0 +1,9 @@
+config DISK
+       bool "Support disk controllers with driver model"
+       depends on DM
+       default y if DM
+       help
+         This enables a uclass for disk controllers  in U-Boot. Various driver

nits: one more space before "in U-Boot"

Quoted 1 line

I can fix this when applying.

Fixed nits, and

Quoted 43 lines
Quoted 43 lines
drivers/block/Kconfig +3 -0
+         types can use this, such as AHCI/SATA. It does not provide any standard
+         operations at present. The block device interface has not been converted
+         to driver model.
drivers/block/Makefile +1 -0
index eb8bda9..5eb87e0 100644
@@ -5,6 +5,7 @@
 # SPDX-License-Identifier:     GPL-2.0+
 #
 
+obj-$(CONFIG_DISK) += disk-uclass.o
 obj-$(CONFIG_SCSI_AHCI) += ahci.o
 obj-$(CONFIG_DWC_AHSATA) += dwc_ahsata.o
 obj-$(CONFIG_FSL_SATA) += fsl_sata.o
drivers/block/disk-uclass.c new file +14 -0
new file mode 100644
index 0000000..d665b35
@@ -0,0 +1,14 @@
+/*
+ * Copyright (c) 2015 Google, Inc
+ * Written by Simon Glass <[email protected]>
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+
+UCLASS_DRIVER(disk) = {
+       .id             = UCLASS_DISK,
+       .name           = "disk",
+};
include/dm/uclass-id.h +0 -0
index 4a6827b..2e10953 100644
@@ -29,6 +29,7 @@ enum uclass_id {
        UCLASS_CLK,             /* Clock source, e.g. used by peripherals */
        UCLASS_CPU,             /* CPU, typically part of an SoC */
Quoted 8 lines

include/dm/uclass-id.h enum uclass_id {

Quoted 6 lines
include/dm/uclass-id.h +1 -1
        UCLASS_CROS_EC,         /* Chrome OS EC */
+       UCLASS_DISK,            /* Disk controller, e.g. SATA */
        UCLASS_DISPLAY_PORT,    /* Display port video */
        UCLASS_RAM,             /* RAM controller */
        UCLASS_ETH,             /* Ethernet device */
--

applied to u-boot-x86/master, thanks!

#72 lore raw

PATCH v2 30/55 x86: ivybridge: Do the SATA init before relocation

In reply to Simon Glass

The SATA device needs to set itself up so that it appears correctly on the PCI bus. The easiest way to do this is to set it up to probe before relocation. This can do the early setup.

---

Changes in v2:
- Update to use the disk uclass

 arch/x86/cpu/ivybridge/bd82x6x.c              |  2 --
 arch/x86/cpu/ivybridge/cpu.c                  |  3 +++
 arch/x86/cpu/ivybridge/sata.c                 | 25 ++++++++++++++++++++++++-
 arch/x86/dts/chromebook_link.dts              | 16 +++++++++-------
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 36 insertions(+), 11 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -2
index c5a5d4d..8e98fa2 100644
@@ -69,8 +69,6 @@ int bd82x6x_init_extra(void)
 		return -EINVAL;
 	}
 
-	bd82x6x_sata_enable(PCH_SATA_DEV, blob, sata_node);
-
 	return 0;
 }
 
arch/x86/cpu/ivybridge/cpu.c +3 -0
index 6d3f477..4cf2ba0 100644
@@ -251,6 +251,9 @@ int print_cpuinfo(void)
 	if (!dev)
 		return -ENODEV;
 
+	/* Cause the SATA device to do its early init */
+	uclass_first_device(UCLASS_DISK, &dev);
+
 	/* Check PM1_STS[15] to see if we are waking from Sx */
 	pm1_sts = inw(DEFAULT_PMBASE + PM1_STS);
 
arch/x86/cpu/ivybridge/sata.c +24 -1
index e7bf03c..c46ec3a 100644
@@ -6,12 +6,15 @@
  */
 
 #include <common.h>
+#include <dm.h>
 #include <fdtdec.h>
 #include <asm/io.h>
 #include <asm/pci.h>
 #include <asm/arch/pch.h>
 #include <asm/arch/bd82x6x.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 static inline u32 sir_read(pci_dev_t dev, int idx)
 {
 	x86_pci_write_config32(dev, SATA_SIRI, idx);
@@ -206,7 +209,7 @@ void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
 	pch_iobp_update(0xea00408a, 0xfffffcff, 0x00000100);
 }
 
-void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node)
+static void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node)
 {
 	unsigned port_map;
 	const char *mode;
@@ -224,3 +227,23 @@ void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node)
 	map |= (port_map ^ 0x3f) << 8;
 	x86_pci_write_config16(dev, 0x90, map);
 }
+
+static int bd82x6x_sata_probe(struct udevice *dev)
+{
+	if (!(gd->flags & GD_FLG_RELOC))
+		bd82x6x_sata_enable(PCH_SATA_DEV, gd->fdt_blob, dev->of_offset);
+
+	return 0;
+}
+
+static const struct udevice_id bd82x6x_ahci_ids[] = {
+	{ .compatible = "intel,pantherpoint-ahci" },
+	{ }
+};
+
+U_BOOT_DRIVER(ahci_ivybridge_drv) = {
+	.name		= "ahci_ivybridge",
+	.id		= UCLASS_DISK,
+	.of_match	= bd82x6x_ahci_ids,
+	.probe		= bd82x6x_sata_probe,
+};
arch/x86/dts/chromebook_link.dts +9 -7
index 3ed6662..022b04c 100644
@@ -207,13 +207,6 @@
 			u-boot,dm-pre-reloc;
 		};
 
-		sata {
-			compatible = "intel,pantherpoint-ahci";
-			intel,sata-mode = "ahci";
-			intel,sata-port-map = <1>;
-			intel,sata-port0-gen3-tx = <0x00880a7f>;
-		};
-
 		gma {
 			compatible = "intel,gma";
 			intel,dp_hotplug = <0 0 0x06>;
@@ -281,6 +274,15 @@
 				};
 			};
 		};
+
+		sata at 1f,2 {
+			compatible = "intel,pantherpoint-ahci";
+			reg = <0x0000fa00 0 0 0 0>;
+			u-boot,dm-pre-reloc;
+			intel,sata-mode = "ahci";
+			intel,sata-port-map = <1>;
+			intel,sata-port0-gen3-tx = <0x00880a7f>;
+		};
 	};
 
 	tpm {
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index 0f4fe47..faae5ff 100644
@@ -8,7 +8,6 @@
 #define _ASM_ARCH_BD82X6X_H
 
 void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node);
-void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node);
 void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#73 lore raw

PATCH v2 30/55 x86: ivybridge: Do the SATA init before relocation

Quoted 10 lines · Simon Glass

The SATA device needs to set itself up so that it appears correctly on the PCI bus. The easiest way to do this is to set it up to probe before relocation. This can do the early setup.

---

Changes in v2:
- Update to use the disk uclass

Quoted 7 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              |  2 --
 arch/x86/cpu/ivybridge/cpu.c                  |  3 +++
 arch/x86/cpu/ivybridge/sata.c                 | 25 ++++++++++++++++++++++++-
 arch/x86/dts/chromebook_link.dts              | 16 +++++++++-------
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 36 insertions(+), 11 deletions(-)
#74 lore raw

PATCH v2 30/55 x86: ivybridge: Do the SATA init before relocation

Quoted 19 lines · Bin Meng
Quoted 10 lines · Simon Glass

The SATA device needs to set itself up so that it appears correctly on the PCI bus. The easiest way to do this is to set it up to probe before relocation. This can do the early setup.

---

Changes in v2:
- Update to use the disk uclass

Quoted 7 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              |  2 --
 arch/x86/cpu/ivybridge/cpu.c                  |  3 +++
 arch/x86/cpu/ivybridge/sata.c                 | 25 ++++++++++++++++++++++++-
 arch/x86/dts/chromebook_link.dts              | 16 +++++++++-------
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 36 insertions(+), 11 deletions(-)
Quoted 1 line

applied to u-boot-x86/master, thanks!

#75 lore raw

PATCH v2 31/55 x86: ivybridge: Drop the unused bd82x6x_init_extra()

In reply to Simon Glass

This function does nothing now so can be dropped.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              | 16 ----------------
 arch/x86/cpu/ivybridge/pci.c                  |  1 -
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 18 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -16
index 8e98fa2..1fe2ce1 100644
@@ -56,22 +56,6 @@ static int bd82x6x_probe(struct udevice *dev)
 	return 0;
 }
 
-/* TODO(sjg at chromium.org): Move this to the PCH init() method */
-int bd82x6x_init_extra(void)
-{
-	const void *blob = gd->fdt_blob;
-	int sata_node;
-
-	sata_node = fdtdec_next_compatible(blob, 0,
-					   COMPAT_INTEL_PANTHERPOINT_AHCI);
-	if (sata_node < 0) {
-		debug("%s: Cannot find SATA node\n", __func__);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
 static int bd82x6x_pch_get_sbase(struct udevice *dev, ulong *sbasep)
 {
 	u32 rcba;
arch/x86/cpu/ivybridge/pci.c +0 -1
index b081469..5195002 100644
@@ -22,7 +22,6 @@ static int pci_ivybridge_probe(struct udevice *bus)
 	if (!(gd->flags & GD_FLG_RELOC))
 		return 0;
 	post_code(0x50);
-	bd82x6x_init_extra();
 	post_code(0x51);
 
 	return 0;
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index faae5ff..7a05c7e 100644
@@ -11,6 +11,5 @@ void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node);
 void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
-int bd82x6x_init_extra(void);
 
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#76 lore raw

PATCH v2 31/55 x86: ivybridge: Drop the unused bd82x6x_init_extra()

Quoted 4 lines · Simon Glass

This function does nothing now so can be dropped.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              | 16 ----------------
 arch/x86/cpu/ivybridge/pci.c                  |  1 -
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 18 deletions(-)

applied to u-boot-x86/master, thanks!

#77 lore raw

PATCH v2 32/55 x86: ivybridge: Use the SATA driver to do the init

In reply to Simon Glass

Instead of manually initing the device, probe the SATA device and move the init there.

---

Changes in v2:
- Update to use the disk uclass

 arch/x86/cpu/ivybridge/bd82x6x.c              | 13 +++++--------
 arch/x86/cpu/ivybridge/sata.c                 |  4 +++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 8 insertions(+), 10 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +5 -8
index 1fe2ce1..188b7da 100644
@@ -22,7 +22,7 @@ static int bd82x6x_probe(struct udevice *dev)
 {
 	const void *blob = gd->fdt_blob;
 	struct pci_controller *hose;
-	int sata_node, gma_node;
+	int gma_node;
 	int ret;
 
 	if (!(gd->flags & GD_FLG_RELOC))
@@ -31,13 +31,10 @@ static int bd82x6x_probe(struct udevice *dev)
 	hose = pci_bus_to_hose(0);
 	lpc_enable(PCH_LPC_DEV);
 	lpc_init_extra(hose, PCH_LPC_DEV);
-	sata_node = fdtdec_next_compatible(blob, 0,
-					   COMPAT_INTEL_PANTHERPOINT_AHCI);
-	if (sata_node < 0) {
-		debug("%s: Cannot find SATA node\n", __func__);
-		return -EINVAL;
-	}
-	bd82x6x_sata_init(PCH_SATA_DEV, blob, sata_node);
+
+	/* Cause the SATA device to do its init */
+	uclass_first_device(UCLASS_DISK, &dev);
+
 	bd82x6x_usb_ehci_init(PCH_EHCI1_DEV);
 	bd82x6x_usb_ehci_init(PCH_EHCI2_DEV);
 
arch/x86/cpu/ivybridge/sata.c +3 -1
index c46ec3a..6314566 100644
@@ -47,7 +47,7 @@ static void common_sata_init(pci_dev_t dev, unsigned int port_map)
 	x86_pci_write_config32(dev, 0x94, ((port_map ^ 0x3f) << 24) | 0x183);
 }
 
-void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
+static void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
 {
 	unsigned int port_map, speed_support, port_tx;
 	struct pci_controller *hose = pci_bus_to_hose(0);
@@ -232,6 +232,8 @@ static int bd82x6x_sata_probe(struct udevice *dev)
 {
 	if (!(gd->flags & GD_FLG_RELOC))
 		bd82x6x_sata_enable(PCH_SATA_DEV, gd->fdt_blob, dev->of_offset);
+	else
+		bd82x6x_sata_init(PCH_SATA_DEV, gd->fdt_blob, dev->of_offset);
 
 	return 0;
 }
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index 7a05c7e..bb3a6c9 100644
@@ -7,7 +7,6 @@
 #ifndef _ASM_ARCH_BD82X6X_H
 #define _ASM_ARCH_BD82X6X_H
 
-void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node);
 void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#78 lore raw

PATCH v2 32/55 x86: ivybridge: Use the SATA driver to do the init

Quoted 6 lines · Simon Glass

Instead of manually initing the device, probe the SATA device and move the init there.

---

Quoted 8 lines

Changes in v2:
- Update to use the disk uclass

 arch/x86/cpu/ivybridge/bd82x6x.c              | 13 +++++--------
 arch/x86/cpu/ivybridge/sata.c                 |  4 +++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 8 insertions(+), 10 deletions(-)
#79 lore raw

PATCH v2 32/55 x86: ivybridge: Use the SATA driver to do the init

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

Instead of manually initing the device, probe the SATA device and move the init there.

---

Changes in v2:
- Update to use the disk uclass

Quoted 7 lines
Quoted 5 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              | 13 +++++--------
 arch/x86/cpu/ivybridge/sata.c                 |  4 +++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 8 insertions(+), 10 deletions(-)

applied to u-boot-x86/master, thanks!

#80 lore raw

PATCH v2 33/55 x86: ivybridge: Use driver model PCI API in sata.c

In reply to Simon Glass

Adjust the functions in this file to use the driver model PCI API.

---

Changes in v2:
- Drop unnecessary IRQ and command register init

 arch/x86/cpu/ivybridge/sata.c | 94 +++++++++++++++++++++----------------------
 1 file changed, 45 insertions(+), 49 deletions(-)
arch/x86/cpu/ivybridge/sata.c +45 -49
index 6314566..21e11d1 100644
@@ -15,42 +15,47 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static inline u32 sir_read(pci_dev_t dev, int idx)
+static inline u32 sir_read(struct udevice *dev, int idx)
 {
-	x86_pci_write_config32(dev, SATA_SIRI, idx);
-	return x86_pci_read_config32(dev, SATA_SIRD);
+	u32 data;
+
+	dm_pci_write_config32(dev, SATA_SIRI, idx);
+	dm_pci_read_config32(dev, SATA_SIRD, &data);
+
+	return data;
 }
 
-static inline void sir_write(pci_dev_t dev, int idx, u32 value)
+static inline void sir_write(struct udevice *dev, int idx, u32 value)
 {
-	x86_pci_write_config32(dev, SATA_SIRI, idx);
-	x86_pci_write_config32(dev, SATA_SIRD, value);
+	dm_pci_write_config32(dev, SATA_SIRI, idx);
+	dm_pci_write_config32(dev, SATA_SIRD, value);
 }
 
-static void common_sata_init(pci_dev_t dev, unsigned int port_map)
+static void common_sata_init(struct udevice *dev, unsigned int port_map)
 {
 	u32 reg32;
 	u16 reg16;
 
 	/* Set IDE I/O Configuration */
 	reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
-	x86_pci_write_config32(dev, IDE_CONFIG, reg32);
+	dm_pci_write_config32(dev, IDE_CONFIG, reg32);
 
 	/* Port enable */
-	reg16 = x86_pci_read_config16(dev, 0x92);
+	dm_pci_read_config16(dev, 0x92, &reg16);
 	reg16 &= ~0x3f;
 	reg16 |= port_map;
-	x86_pci_write_config16(dev, 0x92, reg16);
+	dm_pci_write_config16(dev, 0x92, reg16);
 
 	/* SATA Initialization register */
 	port_map &= 0xff;
-	x86_pci_write_config32(dev, 0x94, ((port_map ^ 0x3f) << 24) | 0x183);
+	dm_pci_write_config32(dev, 0x94, ((port_map ^ 0x3f) << 24) | 0x183);
 }
 
-static void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
+static void bd82x6x_sata_init(struct udevice *dev)
 {
 	unsigned int port_map, speed_support, port_tx;
-	struct pci_controller *hose = pci_bus_to_hose(0);
+	const void *blob = gd->fdt_blob;
+	int node = dev->of_offset;
 	const char *mode;
 	u32 reg32;
 	u16 reg16;
@@ -62,33 +67,27 @@ static void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
 	speed_support = fdtdec_get_int(blob, node,
 				       "sata_interface_speed_support", 0);
 
-	/* Enable BARs */
-	x86_pci_write_config16(dev, PCI_COMMAND, 0x0007);
-
 	mode = fdt_getprop(blob, node, "intel,sata-mode", NULL);
 	if (!mode || !strcmp(mode, "ahci")) {
 		u32 abar;
 
 		debug("SATA: Controller in AHCI mode\n");
 
-		/* Set Interrupt Line, Interrupt Pin is set by D31IP.PIP */
-		x86_pci_write_config8(dev, INTR_LN, 0x0a);
-
 		/* Set timings */
-		x86_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
 				IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
 				IDE_PPE0 | IDE_IE0 | IDE_TIME0);
-		x86_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
 				IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
 
 		/* Sync DMA */
-		x86_pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
-		x86_pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
+		dm_pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
+		dm_pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
 
 		common_sata_init(dev, 0x8000 | port_map);
 
 		/* Initialize AHCI memory-mapped space */
-		abar = pci_read_bar32(hose, dev, 5);
+		abar = dm_pci_read_bar32(dev, 5);
 		debug("ABAR: %08X\n", abar);
 		/* CAP (HBA Capabilities) : enable power management */
 		reg32 = readl(abar + 0x00);
@@ -116,59 +115,54 @@ static void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
 		debug("SATA: Controller in combined mode\n");
 
 		/* No AHCI: clear AHCI base */
-		pci_write_bar32(hose, dev, 5, 0x00000000);
+		dm_pci_write_bar32(dev, 5, 0x00000000);
 		/* And without AHCI BAR no memory decoding */
-		reg16 = x86_pci_read_config16(dev, PCI_COMMAND);
+		dm_pci_read_config16(dev, PCI_COMMAND, &reg16);
 		reg16 &= ~PCI_COMMAND_MEMORY;
-		x86_pci_write_config16(dev, PCI_COMMAND, reg16);
+		dm_pci_write_config16(dev, PCI_COMMAND, reg16);
 
-		x86_pci_write_config8(dev, 0x09, 0x80);
+		dm_pci_write_config8(dev, 0x09, 0x80);
 
 		/* Set timings */
-		x86_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
 				IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
-		x86_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
 				IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
 				IDE_PPE0 | IDE_IE0 | IDE_TIME0);
 
 		/* Sync DMA */
-		x86_pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
-		x86_pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
+		dm_pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
+		dm_pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
 
 		common_sata_init(dev, port_map);
 	} else {
 		debug("SATA: Controller in plain-ide mode\n");
 
 		/* No AHCI: clear AHCI base */
-		pci_write_bar32(hose, dev, 5, 0x00000000);
+		dm_pci_write_bar32(dev, 5, 0x00000000);
 
 		/* And without AHCI BAR no memory decoding */
-		reg16 = x86_pci_read_config16(dev, PCI_COMMAND);
+		dm_pci_read_config16(dev, PCI_COMMAND, &reg16);
 		reg16 &= ~PCI_COMMAND_MEMORY;
-		x86_pci_write_config16(dev, PCI_COMMAND, reg16);
+		dm_pci_write_config16(dev, PCI_COMMAND, reg16);
 
 		/*
 		 * Native mode capable on both primary and secondary (0xa)
 		 * OR'ed with enabled (0x50) = 0xf
 		 */
-		x86_pci_write_config8(dev, 0x09, 0x8f);
-
-		/* Set Interrupt Line */
-		/* Interrupt Pin is set by D31IP.PIP */
-		x86_pci_write_config8(dev, INTR_LN, 0xff);
+		dm_pci_write_config8(dev, 0x09, 0x8f);
 
 		/* Set timings */
-		x86_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
 				IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
 				IDE_PPE0 | IDE_IE0 | IDE_TIME0);
-		x86_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+		dm_pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
 				IDE_SITRE | IDE_ISP_3_CLOCKS |
 				IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0);
 
 		/* Sync DMA */
-		x86_pci_write_config16(dev, IDE_SDMA_CNT,
-				       IDE_SSDE0 | IDE_PSDE0);
-		x86_pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
+		dm_pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0);
+		dm_pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
 
 		common_sata_init(dev, port_map);
 	}
@@ -209,8 +203,10 @@ static void bd82x6x_sata_init(pci_dev_t dev, const void *blob, int node)
 	pch_iobp_update(0xea00408a, 0xfffffcff, 0x00000100);
 }
 
-static void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node)
+static void bd82x6x_sata_enable(struct udevice *dev)
 {
+	const void *blob = gd->fdt_blob;
+	int node = dev->of_offset;
 	unsigned port_map;
 	const char *mode;
 	u16 map = 0;
@@ -225,15 +221,15 @@ static void bd82x6x_sata_enable(pci_dev_t dev, const void *blob, int node)
 	port_map = fdtdec_get_int(blob, node, "intel,sata-port-map", 0);
 
 	map |= (port_map ^ 0x3f) << 8;
-	x86_pci_write_config16(dev, 0x90, map);
+	dm_pci_write_config16(dev, 0x90, map);
 }
 
 static int bd82x6x_sata_probe(struct udevice *dev)
 {
 	if (!(gd->flags & GD_FLG_RELOC))
-		bd82x6x_sata_enable(PCH_SATA_DEV, gd->fdt_blob, dev->of_offset);
+		bd82x6x_sata_enable(dev);
 	else
-		bd82x6x_sata_init(PCH_SATA_DEV, gd->fdt_blob, dev->of_offset);
+		bd82x6x_sata_init(dev);
 
 	return 0;
 }
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#81 lore raw

PATCH v2 33/55 x86: ivybridge: Use driver model PCI API in sata.c

Quoted 11 lines · Simon Glass

Adjust the functions in this file to use the driver model PCI API.

---

Changes in v2:
- Drop unnecessary IRQ and command register init

 arch/x86/cpu/ivybridge/sata.c | 94 +++++++++++++++++++++----------------------
 1 file changed, 45 insertions(+), 49 deletions(-)
#82 lore raw

PATCH v2 33/55 x86: ivybridge: Use driver model PCI API in sata.c

Quoted 6 lines · Bin Meng
Quoted 5 lines · Simon Glass

Adjust the functions in this file to use the driver model PCI API.

---

Quoted 8 lines
Quoted 6 lines

Changes in v2:
- Drop unnecessary IRQ and command register init

 arch/x86/cpu/ivybridge/sata.c | 94 +++++++++++++++++++++----------------------
 1 file changed, 45 insertions(+), 49 deletions(-)

applied to u-boot-x86/master, thanks!

#83 lore raw

PATCH v2 34/55 x86: ivybridge: Move lpc_enable() into gma.c

In reply to Simon Glass

This graphics init code is best placed in the gma init code. Move the code and drop the function.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c          | 1 -
 arch/x86/cpu/ivybridge/gma.c              | 4 ++++
 arch/x86/cpu/ivybridge/lpc.c              | 7 -------
 arch/x86/include/asm/arch-ivybridge/pch.h | 1 -
 4 files changed, 4 insertions(+), 9 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -1
index 188b7da..9e7e30a 100644
@@ -29,7 +29,6 @@ static int bd82x6x_probe(struct udevice *dev)
 		return 0;
 
 	hose = pci_bus_to_hose(0);
-	lpc_enable(PCH_LPC_DEV);
 	lpc_init_extra(hose, PCH_LPC_DEV);
 
 	/* Cause the SATA device to do its init */
arch/x86/cpu/ivybridge/gma.c +4 -0
index 1748f7f..b94536c 100644
@@ -806,6 +806,10 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 	u32 reg32;
 	int ret;
 
+	/* Enable PCH Display Port */
+	writew(0x0010, RCB_REG(DISPBDF));
+	setbits_le32(RCB_REG(FD2), PCH_ENABLE_DBDF);
+
 	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &nbridge);
 	if (!nbridge)
 		return -ENODEV;
arch/x86/cpu/ivybridge/lpc.c +0 -7
index 0d85de2..44c4825 100644
@@ -602,13 +602,6 @@ int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev)
 	return 0;
 }
 
-void lpc_enable(pci_dev_t dev)
-{
-	/* Enable PCH Display Port */
-	writew(0x0010, RCB_REG(DISPBDF));
-	setbits_le32(RCB_REG(FD2), PCH_ENABLE_DBDF);
-}
-
 static int bd82x6x_lpc_early_init(struct udevice *dev)
 {
 	/* Setting up Southbridge. In the northbridge code. */
arch/x86/include/asm/arch-ivybridge/pch.h +0 -1
index f35803b..682a557 100644
@@ -471,6 +471,5 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue);
 #define TCO2_STS	0x66
 
 int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev);
-void lpc_enable(pci_dev_t dev);
 
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#84 lore raw

PATCH v2 34/55 x86: ivybridge: Move lpc_enable() into gma.c

Quoted 7 lines · Simon Glass

This graphics init code is best placed in the gma init code. Move the code and drop the function.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c          | 1 -
 arch/x86/cpu/ivybridge/gma.c              | 4 ++++
 arch/x86/cpu/ivybridge/lpc.c              | 7 -------
 arch/x86/include/asm/arch-ivybridge/pch.h | 1 -
 4 files changed, 4 insertions(+), 9 deletions(-)

applied to u-boot-x86/master, thanks!

#85 lore raw

PATCH v2 35/55 x86: ivybridge: Move LPC init into the LPC probe() method

In reply to Simon Glass

Drop the lpc_init_extra() function and just use the post-relocation LPC probe() instead.

---

Changes in v2:
- Update to use LPC probe() method instead of init()

 arch/x86/cpu/ivybridge/bd82x6x.c          |  4 ----
 arch/x86/cpu/ivybridge/lpc.c              | 17 +++++++++--------
 arch/x86/include/asm/arch-ivybridge/pch.h |  2 --
 3 files changed, 9 insertions(+), 14 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +0 -4
index 9e7e30a..5cb4152 100644
@@ -21,16 +21,12 @@
 static int bd82x6x_probe(struct udevice *dev)
 {
 	const void *blob = gd->fdt_blob;
-	struct pci_controller *hose;
 	int gma_node;
 	int ret;
 
 	if (!(gd->flags & GD_FLG_RELOC))
 		return 0;
 
-	hose = pci_bus_to_hose(0);
-	lpc_init_extra(hose, PCH_LPC_DEV);
-
 	/* Cause the SATA device to do its init */
 	uclass_first_device(UCLASS_DISK, &dev);
 
arch/x86/cpu/ivybridge/lpc.c +9 -8
index 44c4825..79224d9 100644
@@ -538,7 +538,7 @@ static int lpc_early_init(struct udevice *dev)
 	return 0;
 }
 
-int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev)
+static int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev)
 {
 	const void *blob = gd->fdt_blob;
 	int node;
@@ -626,16 +626,17 @@ static int bd82x6x_lpc_probe(struct udevice *dev)
 {
 	int ret;
 
-	if (gd->flags & GD_FLG_RELOC)
-		return 0;
+	if (!(gd->flags & GD_FLG_RELOC)) {
+		ret = lpc_early_init(dev);
+		if (ret) {
+			debug("%s: lpc_early_init() failed\n", __func__);
+			return ret;
+		}
 
-	ret = lpc_early_init(dev);
-	if (ret) {
-		debug("%s: lpc_early_init() failed\n", __func__);
-		return ret;
+		return bd82x6x_lpc_early_init(dev);
 	}
 
-	return bd82x6x_lpc_early_init(dev);
+	return lpc_init_extra(pci_bus_to_hose(0), PCH_LPC_DEV);
 }
 
 static const struct udevice_id bd82x6x_lpc_ids[] = {
arch/x86/include/asm/arch-ivybridge/pch.h +0 -2
index 682a557..629a144 100644
@@ -470,6 +470,4 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue);
 #define   DMISCI_STS	(1 << 9)
 #define TCO2_STS	0x66
 
-int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev);
-
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#86 lore raw

PATCH v2 35/55 x86: ivybridge: Move LPC init into the LPC probe() method

Quoted 7 lines · Simon Glass

Drop the lpc_init_extra() function and just use the post-relocation LPC probe() instead.

---

Quoted 8 lines

Changes in v2:
- Update to use LPC probe() method instead of init()

 arch/x86/cpu/ivybridge/bd82x6x.c          |  4 ----
 arch/x86/cpu/ivybridge/lpc.c              | 17 +++++++++--------
 arch/x86/include/asm/arch-ivybridge/pch.h |  2 --
 3 files changed, 9 insertions(+), 14 deletions(-)

applied to u-boot-x86/master, thanks!

#87 lore raw

PATCH v2 36/55 x86: ivybridge: Drop the special PCI driver

In reply to Simon Glass

There is nothing special about the ivybridge pci driver now, so just use the generic one.

---

Changes in v2:
- Drop the special compatible string in chromebook_link.dts

 arch/x86/cpu/ivybridge/Makefile  |  1 -
 arch/x86/cpu/ivybridge/pci.c     | 46 ----------------------------------------
 arch/x86/dts/chromebook_link.dts |  2 +-
 3 files changed, 1 insertion(+), 48 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/pci.c
arch/x86/cpu/ivybridge/Makefile +0 -1
index bdbd3fa..259a5df 100644
@@ -15,7 +15,6 @@ obj-y += model_206ax.o
 obj-y += microcode_intel.o
 obj-y += northbridge.o
 obj-y += pch.o
-obj-y += pci.o
 obj-y += report_platform.o
 obj-y += sata.o
 obj-y += sdram.o
arch/x86/cpu/ivybridge/pci.c deleted +0 -46

46 lines not on this page · raw message

arch/x86/dts/chromebook_link.dts +1 -1
index 022b04c..18305a3 100644
@@ -193,7 +193,7 @@
 	};
 
 	pci {
-		compatible = "intel,pci-ivybridge", "pci-x86";
+		compatible = "pci-x86";
 		#address-cells = <3>;
 		#size-cells = <2>;
 		u-boot,dm-pre-reloc;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#88 lore raw

PATCH v2 36/55 x86: ivybridge: Drop the special PCI driver

Quoted 6 lines · Simon Glass

There is nothing special about the ivybridge pci driver now, so just use the generic one.

---

Quoted 9 lines

Changes in v2:
- Drop the special compatible string in chromebook_link.dts

 arch/x86/cpu/ivybridge/Makefile  |  1 -
 arch/x86/cpu/ivybridge/pci.c     | 46 ----------------------------------------
 arch/x86/dts/chromebook_link.dts |  2 +-
 3 files changed, 1 insertion(+), 48 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/pci.c
#89 lore raw

PATCH v2 36/55 x86: ivybridge: Drop the special PCI driver

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

There is nothing special about the ivybridge pci driver now, so just use the generic one.

---

Changes in v2:
- Drop the special compatible string in chromebook_link.dts

Quoted 8 lines
Quoted 6 lines
 arch/x86/cpu/ivybridge/Makefile  |  1 -
 arch/x86/cpu/ivybridge/pci.c     | 46 ----------------------------------------
 arch/x86/dts/chromebook_link.dts |  2 +-
 3 files changed, 1 insertion(+), 48 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/pci.c

applied to u-boot-x86/master, thanks!

#90 lore raw

PATCH v2 37/55 x86: ivybridge: Convert lpc init code to DM PCI API

In reply to Simon Glass

Adjust this code to use the driver model PCI API. This is all called through lpc_init_extra().

---

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c | 129 ++++++++++++++++++++++---------------------
 1 file changed, 66 insertions(+), 63 deletions(-)
arch/x86/cpu/ivybridge/lpc.c +66 -63
index 79224d9..0cf55c5 100644
@@ -24,13 +24,13 @@
 #define ENABLE_ACPI_MODE_IN_COREBOOT	0
 #define TEST_SMM_FLASH_LOCKDOWN		0
 
-static int pch_enable_apic(pci_dev_t dev)
+static int pch_enable_apic(struct udevice *pch)
 {
 	u32 reg32;
 	int i;
 
 	/* Enable ACPI I/O and power management. Set SCI IRQ to IRQ9 */
-	x86_pci_write_config8(dev, ACPI_CNTL, 0x80);
+	dm_pci_write_config8(pch, ACPI_CNTL, 0x80);
 
 	writel(0, IO_APIC_INDEX);
 	writel(1 << 25, IO_APIC_DATA);
@@ -66,36 +66,36 @@ static int pch_enable_apic(pci_dev_t dev)
 	return 0;
 }
 
-static void pch_enable_serial_irqs(pci_dev_t dev)
+static void pch_enable_serial_irqs(struct udevice *pch)
 {
 	u32 value;
 
 	/* Set packet length and toggle silent mode bit for one frame. */
 	value = (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0);
 #ifdef CONFIG_SERIRQ_CONTINUOUS_MODE
-	x86_pci_write_config8(dev, SERIRQ_CNTL, value);
+	dm_pci_write_config8(pch, SERIRQ_CNTL, value);
 #else
-	x86_pci_write_config8(dev, SERIRQ_CNTL, value | (1 << 6));
+	dm_pci_write_config8(pch, SERIRQ_CNTL, value | (1 << 6));
 #endif
 }
 
-static int pch_pirq_init(const void *blob, int node, pci_dev_t dev)
+static int pch_pirq_init(struct udevice *pch)
 {
 	uint8_t route[8], *ptr;
 
-	if (fdtdec_get_byte_array(blob, node, "intel,pirq-routing", route,
-				  sizeof(route)))
+	if (fdtdec_get_byte_array(gd->fdt_blob, pch->of_offset,
+				  "intel,pirq-routing", route, sizeof(route)))
 		return -EINVAL;
 	ptr = route;
-	x86_pci_write_config8(dev, PIRQA_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQB_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQC_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQD_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQA_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQB_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQC_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQD_ROUT, *ptr++);
 
-	x86_pci_write_config8(dev, PIRQE_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQF_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQG_ROUT, *ptr++);
-	x86_pci_write_config8(dev, PIRQH_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQE_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQF_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQG_ROUT, *ptr++);
+	dm_pci_write_config8(pch, PIRQH_ROUT, *ptr++);
 
 	/*
 	 * TODO(sjg at chromium.org): U-Boot does not set up the interrupts
@@ -104,26 +104,28 @@ static int pch_pirq_init(const void *blob, int node, pci_dev_t dev)
 	return 0;
 }
 
-static int pch_gpi_routing(const void *blob, int node, pci_dev_t dev)
+static int pch_gpi_routing(struct udevice *pch)
 {
 	u8 route[16];
 	u32 reg;
 	int gpi;
 
-	if (fdtdec_get_byte_array(blob, node, "intel,gpi-routing", route,
-				  sizeof(route)))
+	if (fdtdec_get_byte_array(gd->fdt_blob, pch->of_offset,
+				  "intel,gpi-routing", route, sizeof(route)))
 		return -EINVAL;
 
 	for (reg = 0, gpi = 0; gpi < ARRAY_SIZE(route); gpi++)
 		reg |= route[gpi] << (gpi * 2);
 
-	x86_pci_write_config32(dev, 0xb8, reg);
+	dm_pci_write_config32(pch, 0xb8, reg);
 
 	return 0;
 }
 
-static int pch_power_options(const void *blob, int node, pci_dev_t dev)
+static int pch_power_options(struct udevice *pch)
 {
+	const void *blob = gd->fdt_blob;
+	int node = pch->of_offset;
 	u8 reg8;
 	u16 reg16, pmbase;
 	u32 reg32;
@@ -142,7 +144,7 @@ static int pch_power_options(const void *blob, int node, pci_dev_t dev)
 	 */
 	pwr_on = MAINBOARD_POWER_ON;
 
-	reg16 = x86_pci_read_config16(dev, GEN_PMCON_3);
+	dm_pci_read_config16(pch, GEN_PMCON_3, &reg16);
 	reg16 &= 0xfffe;
 	switch (pwr_on) {
 	case MAINBOARD_POWER_OFF:
@@ -169,7 +171,7 @@ static int pch_power_options(const void *blob, int node, pci_dev_t dev)
 
 	reg16 |= (1 << 12);	/* Disable SLP stretch after SUS well */
 
-	x86_pci_write_config16(dev, GEN_PMCON_3, reg16);
+	dm_pci_write_config16(pch, GEN_PMCON_3, reg16);
 	debug("Set power %s after power failure.\n", state);
 
 	/* Set up NMI on errors. */
@@ -193,21 +195,22 @@ static int pch_power_options(const void *blob, int node, pci_dev_t dev)
 	outb(reg8, 0x70);
 
 	/* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */
-	reg16 = x86_pci_read_config16(dev, GEN_PMCON_1);
+	dm_pci_read_config16(pch, GEN_PMCON_1, &reg16);
 	reg16 &= ~(3 << 0);	/* SMI# rate 1 minute */
 	reg16 &= ~(1 << 10);	/* Disable BIOS_PCI_EXP_EN for native PME */
 #if DEBUG_PERIODIC_SMIS
 	/* Set DEBUG_PERIODIC_SMIS in pch.h to debug using periodic SMIs */
 	reg16 |= (3 << 0);	/* Periodic SMI every 8s */
 #endif
-	x86_pci_write_config16(dev, GEN_PMCON_1, reg16);
+	dm_pci_write_config16(pch, GEN_PMCON_1, reg16);
 
 	/* Set the board's GPI routing. */
-	ret = pch_gpi_routing(blob, node, dev);
+	ret = pch_gpi_routing(pch);
 	if (ret)
 		return ret;
 
-	pmbase = x86_pci_read_config16(dev, 0x40) & 0xfffe;
+	dm_pci_read_config16(pch, 0x40, &pmbase);
+	pmbase &= 0xfffe;
 
 	writel(pmbase + GPE0_EN, fdtdec_get_int(blob, node,
 						"intel,gpe0-enable", 0));
@@ -227,16 +230,16 @@ static int pch_power_options(const void *blob, int node, pci_dev_t dev)
 	return 0;
 }
 
-static void pch_rtc_init(pci_dev_t dev)
+static void pch_rtc_init(struct udevice *pch)
 {
 	int rtc_failed;
 	u8 reg8;
 
-	reg8 = x86_pci_read_config8(dev, GEN_PMCON_3);
+	dm_pci_read_config8(pch, GEN_PMCON_3, &reg8);
 	rtc_failed = reg8 & RTC_BATTERY_DEAD;
 	if (rtc_failed) {
 		reg8 &= ~RTC_BATTERY_DEAD;
-		x86_pci_write_config8(dev, GEN_PMCON_3, reg8);
+		dm_pci_write_config8(pch, GEN_PMCON_3, reg8);
 	}
 	debug("rtc_failed = 0x%x\n", rtc_failed);
 
@@ -246,10 +249,10 @@ static void pch_rtc_init(pci_dev_t dev)
 }
 
 /* CougarPoint PCH Power Management init */
-static void cpt_pm_init(pci_dev_t dev)
+static void cpt_pm_init(struct udevice *pch)
 {
 	debug("CougarPoint PM init\n");
-	x86_pci_write_config8(dev, 0xa9, 0x47);
+	dm_pci_write_config8(pch, 0xa9, 0x47);
 	setbits_le32(RCB_REG(0x2238), (1 << 6) | (1 << 0));
 
 	setbits_le32(RCB_REG(0x228c), 1 << 0);
@@ -290,10 +293,10 @@ static void cpt_pm_init(pci_dev_t dev)
 }
 
 /* PantherPoint PCH Power Management init */
-static void ppt_pm_init(pci_dev_t dev)
+static void ppt_pm_init(struct udevice *pch)
 {
 	debug("PantherPoint PM init\n");
-	x86_pci_write_config8(dev, 0xa9, 0x47);
+	dm_pci_write_config8(pch, 0xa9, 0x47);
 	setbits_le32(RCB_REG(0x2238), 1 << 0);
 	setbits_le32(RCB_REG(0x228c), 1 << 0);
 	setbits_le16(RCB_REG(0x1100), (1 << 13) | (1 << 14));
@@ -340,16 +343,16 @@ static void enable_hpet(void)
 	clrsetbits_le32(RCB_REG(HPTC), 3 << 0, 1 << 7);
 }
 
-static void enable_clock_gating(pci_dev_t dev)
+static void enable_clock_gating(struct udevice *pch)
 {
 	u32 reg32;
 	u16 reg16;
 
 	setbits_le32(RCB_REG(0x2234), 0xf);
 
-	reg16 = x86_pci_read_config16(dev, GEN_PMCON_1);
+	dm_pci_read_config16(pch, GEN_PMCON_1, &reg16);
 	reg16 |= (1 << 2) | (1 << 11);
-	x86_pci_write_config16(dev, GEN_PMCON_1, reg16);
+	dm_pci_write_config16(pch, GEN_PMCON_1, reg16);
 
 	pch_iobp_update(0xEB007F07, ~0UL, (1 << 31));
 	pch_iobp_update(0xEB004000, ~0UL, (1 << 7));
@@ -429,24 +432,24 @@ static void pch_lock_smm(pci_dev_t dev)
 }
 #endif
 
-static void pch_disable_smm_only_flashing(pci_dev_t dev)
+static void pch_disable_smm_only_flashing(struct udevice *pch)
 {
 	u8 reg8;
 
 	debug("Enabling BIOS updates outside of SMM... ");
-	reg8 = x86_pci_read_config8(dev, 0xdc);	/* BIOS_CNTL */
+	dm_pci_read_config8(pch, 0xdc, &reg8);	/* BIOS_CNTL */
 	reg8 &= ~(1 << 5);
-	x86_pci_write_config8(dev, 0xdc, reg8);
+	dm_pci_write_config8(pch, 0xdc, reg8);
 }
 
-static void pch_fixups(pci_dev_t dev)
+static void pch_fixups(struct udevice *pch)
 {
 	u8 gen_pmcon_2;
 
 	/* Indicate DRAM init done for MRC S3 to know it can resume */
-	gen_pmcon_2 = x86_pci_read_config8(dev, GEN_PMCON_2);
+	dm_pci_read_config8(pch, GEN_PMCON_2, &gen_pmcon_2);
 	gen_pmcon_2 |= (1 << 7);
-	x86_pci_write_config8(dev, GEN_PMCON_2, gen_pmcon_2);
+	dm_pci_write_config8(pch, GEN_PMCON_2, gen_pmcon_2);
 
 	/* Enable DMI ASPM in the PCH */
 	clrbits_le32(RCB_REG(0x2304), 1 << 10);
@@ -538,66 +541,66 @@ static int lpc_early_init(struct udevice *dev)
 	return 0;
 }
 
-static int lpc_init_extra(struct pci_controller *hose, pci_dev_t dev)
+static int lpc_init_extra(struct udevice *dev)
 {
+	struct udevice *pch = dev->parent;
 	const void *blob = gd->fdt_blob;
 	int node;
 
 	debug("pch: lpc_init\n");
-	pci_write_bar32(hose, dev, 0, 0);
-	pci_write_bar32(hose, dev, 1, 0xff800000);
-	pci_write_bar32(hose, dev, 2, 0xfec00000);
-	pci_write_bar32(hose, dev, 3, 0x800);
-	pci_write_bar32(hose, dev, 4, 0x900);
+	dm_pci_write_bar32(pch, 0, 0);
+	dm_pci_write_bar32(pch, 1, 0xff800000);
+	dm_pci_write_bar32(pch, 2, 0xfec00000);
+	dm_pci_write_bar32(pch, 3, 0x800);
+	dm_pci_write_bar32(pch, 4, 0x900);
 
 	node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_PCH);
 	if (node < 0)
 		return -ENOENT;
 
 	/* Set the value for PCI command register. */
-	x86_pci_write_config16(dev, PCI_COMMAND, 0x000f);
+	dm_pci_write_config16(pch, PCI_COMMAND, 0x000f);
 
 	/* IO APIC initialization. */
-	pch_enable_apic(dev);
+	pch_enable_apic(pch);
 
-	pch_enable_serial_irqs(dev);
+	pch_enable_serial_irqs(pch);
 
 	/* Setup the PIRQ. */
-	pch_pirq_init(blob, node, dev);
+	pch_pirq_init(pch);
 
 	/* Setup power options. */
-	pch_power_options(blob, node, dev);
+	pch_power_options(pch);
 
 	/* Initialize power management */
 	switch (pch_silicon_type()) {
 	case PCH_TYPE_CPT: /* CougarPoint */
-		cpt_pm_init(dev);
+		cpt_pm_init(pch);
 		break;
 	case PCH_TYPE_PPT: /* PantherPoint */
-		ppt_pm_init(dev);
+		ppt_pm_init(pch);
 		break;
 	default:
-		printf("Unknown Chipset: %#02x.%dx\n", PCI_DEV(dev),
-		       PCI_FUNC(dev));
+		printf("Unknown Chipset: %s\n", pch->name);
 		return -ENOSYS;
 	}
 
 	/* Initialize the real time clock. */
-	pch_rtc_init(dev);
+	pch_rtc_init(pch);
 
 	/* Initialize the High Precision Event Timers, if present. */
 	enable_hpet();
 
 	/* Initialize Clock Gating */
-	enable_clock_gating(dev);
+	enable_clock_gating(pch);
 
-	pch_disable_smm_only_flashing(dev);
+	pch_disable_smm_only_flashing(pch);
 
 #if CONFIG_HAVE_SMI_HANDLER
 	pch_lock_smm(dev);
 #endif
 
-	pch_fixups(dev);
+	pch_fixups(pch);
 
 	return 0;
 }
@@ -636,7 +639,7 @@ static int bd82x6x_lpc_probe(struct udevice *dev)
 		return bd82x6x_lpc_early_init(dev);
 	}
 
-	return lpc_init_extra(pci_bus_to_hose(0), PCH_LPC_DEV);
+	return lpc_init_extra(dev);
 }
 
 static const struct udevice_id bd82x6x_lpc_ids[] = {
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#91 lore raw

PATCH v2 37/55 x86: ivybridge: Convert lpc init code to DM PCI API

Quoted 12 lines · Simon Glass

Adjust this code to use the driver model PCI API. This is all called through lpc_init_extra().

---

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c | 129 ++++++++++++++++++++++---------------------
 1 file changed, 66 insertions(+), 63 deletions(-)

applied to u-boot-x86/master, thanks!

#92 lore raw

PATCH v2 38/55 x86: Enable DM_USB for link and panther

In reply to Simon Glass

Move these two boards to use driver model for USB.

---

Changes in v2: None

 configs/chromebook_link_defconfig   | 2 ++
 configs/chromebox_panther_defconfig | 2 ++
 2 files changed, 4 insertions(+)
configs/chromebook_link_defconfig +2 -0
index 06e4ce6..f367f81 100644
@@ -37,6 +37,8 @@ CONFIG_SYS_NS16550=y
 CONFIG_ICH_SPI=y
 CONFIG_TIMER=y
 CONFIG_TPM_TIS_LPC=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
 CONFIG_VIDEO_VESA=y
 CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
 CONFIG_FRAMEBUFFER_VESA_MODE_11A=y
configs/chromebox_panther_defconfig +2 -0
index ed4428f..4b78292 100644
@@ -29,6 +29,8 @@ CONFIG_SYS_NS16550=y
 CONFIG_ICH_SPI=y
 CONFIG_TIMER=y
 CONFIG_TPM_TIS_LPC=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
 CONFIG_VIDEO_VESA=y
 CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
 CONFIG_FRAMEBUFFER_VESA_MODE_11A=y
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#93 lore raw

PATCH v2 38/55 x86: Enable DM_USB for link and panther

Quoted 4 lines · Simon Glass

Move these two boards to use driver model for USB.

Quoted 8 lines

---

Changes in v2: None

 configs/chromebook_link_defconfig   | 2 ++
 configs/chromebox_panther_defconfig | 2 ++
 2 files changed, 4 insertions(+)

applied to u-boot-x86/master, thanks!

#94 lore raw

PATCH v2 39/55 x86: i2c: Add a stub driver for Intel I2C/SMbus

In reply to Simon Glass

This is used on most Intel platforms. We don't have a driver for it yet, but add a stub to handle the init. For now this targets ivybridge so we may want to add a device tree binding and generalise it when other platforms are supported.

---

Changes in v2:
- Expand the Kconfig help a little

 drivers/i2c/Kconfig     |  9 +++++++++
 drivers/i2c/Makefile    |  1 +
 drivers/i2c/intel_i2c.c | 51 +++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 61 insertions(+)
 create mode 100644 drivers/i2c/intel_i2c.c
drivers/i2c/Kconfig +9 -0
index 14adda2..46b83e7 100644
@@ -58,6 +58,15 @@ config DM_I2C_GPIO
 	  bindings are supported.
 	  Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
 
+config SYS_I2C_INTEL
+	bool "Intel I2C/SMBUS driver"
+	depends on DM_I2C
+	help
+	  Add support for the Intel SMBUS driver. So far this driver is just
+	  a stub which perhaps some basic init. There is no implementation of
+	  the I2C API meaning that any I2C operations will immediately fail
+	  for now.
+
 config SYS_I2C_ROCKCHIP
 	bool "Rockchip I2C driver"
 	depends on DM_I2C
drivers/i2c/Makefile +1 -0
index 811ad9b..a2a956a 100644
@@ -21,6 +21,7 @@ obj-$(CONFIG_SYS_I2C_DW) += designware_i2c.o
 obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
 obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o
 obj-$(CONFIG_SYS_I2C_IHS) += ihs_i2c.o
+obj-$(CONFIG_SYS_I2C_INTEL) += intel_i2c.o
 obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o
 obj-$(CONFIG_SYS_I2C_LPC32XX) += lpc32xx_i2c.o
 obj-$(CONFIG_SYS_I2C_MVTWSI) += mvtwsi.o
drivers/i2c/intel_i2c.c new file +51 -0

51 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#95 lore raw

PATCH v2 39/55 x86: i2c: Add a stub driver for Intel I2C/SMbus

Quoted 10 lines · Simon Glass

This is used on most Intel platforms. We don't have a driver for it yet, but add a stub to handle the init. For now this targets ivybridge so we may want to add a device tree binding and generalise it when other platforms are supported.

---

Quoted 9 lines

Changes in v2:
- Expand the Kconfig help a little

 drivers/i2c/Kconfig     |  9 +++++++++
 drivers/i2c/Makefile    |  1 +
 drivers/i2c/intel_i2c.c | 51 +++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 61 insertions(+)
 create mode 100644 drivers/i2c/intel_i2c.c

applied to u-boot-x86/master, thanks!

#96 lore raw

PATCH v2 40/55 x86: ivybridge: Use the I2C driver to perform SMbus init

In reply to Simon Glass

Move the init code into the I2C driver.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c      | 39 +++------------------------------------
 arch/x86/dts/chromebook_link.dts  |  6 ++++++
 configs/chromebook_link_defconfig |  2 ++
 drivers/i2c/intel_i2c.c           | 24 ++++++++++++++++++++++++
 4 files changed, 35 insertions(+), 36 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +3 -36
index 4cf2ba0..b9dda4c7 100644
@@ -120,41 +120,6 @@ int arch_cpu_init_dm(void)
 	return 0;
 }
 
-static int enable_smbus(void)
-{
-	pci_dev_t dev;
-	uint16_t value;
-
-	/* Set the SMBus device statically. */
-	dev = PCI_BDF(0x0, 0x1f, 0x3);
-
-	/* Check to make sure we've got the right device. */
-	value = x86_pci_read_config16(dev, 0x0);
-	if (value != 0x8086) {
-		printf("SMBus controller not found\n");
-		return -ENOSYS;
-	}
-
-	/* Set SMBus I/O base. */
-	x86_pci_write_config32(dev, SMB_BASE,
-			       SMBUS_IO_BASE | PCI_BASE_ADDRESS_SPACE_IO);
-
-	/* Set SMBus enable. */
-	x86_pci_write_config8(dev, HOSTC, HST_EN);
-
-	/* Set SMBus I/O space enable. */
-	x86_pci_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO);
-
-	/* Disable interrupt generation. */
-	outb(0, SMBUS_IO_BASE + SMBHSTCTL);
-
-	/* Clear any lingering errors, so transactions can run. */
-	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
-	debug("SMBus controller enabled\n");
-
-	return 0;
-}
-
 #define PCH_EHCI0_TEMP_BAR0 0xe8000000
 #define PCH_EHCI1_TEMP_BAR0 0xe8000400
 #define PCH_XHCI_TEMP_BAR0  0xe8001000
@@ -271,9 +236,11 @@ int print_cpuinfo(void)
 	post_code(POST_EARLY_INIT);
 
 	/* Enable SPD ROMs and DDR-III DRAM */
-	ret = enable_smbus();
+	ret = uclass_first_device(UCLASS_I2C, &dev);
 	if (ret)
 		return ret;
+	if (!dev)
+		return -ENODEV;
 
 	/* Prepare USB controller early in S3 resume */
 	if (boot_mode == PEI_BOOT_RESUME)
arch/x86/dts/chromebook_link.dts +6 -0
index 18305a3..54f2043 100644
@@ -283,6 +283,12 @@
 			intel,sata-port-map = <1>;
 			intel,sata-port0-gen3-tx = <0x00880a7f>;
 		};
+
+		smbus: smbus at 1f,3 {
+			compatible = "intel,ich-i2c";
+			reg = <0x0000fb00 0 0 0 0>;
+			u-boot,dm-pre-reloc;
+		};
 	};
 
 	tpm {
configs/chromebook_link_defconfig +2 -0
index f367f81..daa958e 100644
@@ -1,5 +1,6 @@
 CONFIG_X86=y
 CONFIG_SYS_MALLOC_F_LEN=0x1800
+CONFIG_DM_I2C=y
 CONFIG_VENDOR_GOOGLE=y
 CONFIG_DEFAULT_DEVICE_TREE="chromebook_link"
 CONFIG_TARGET_CHROMEBOOK_LINK=y
@@ -20,6 +21,7 @@ CONFIG_CMD_TPM=y
 CONFIG_CMD_TPM_TEST=y
 CONFIG_OF_CONTROL=y
 CONFIG_CPU=y
+CONFIG_SYS_I2C_INTEL=y
 CONFIG_CMD_CROS_EC=y
 CONFIG_CROS_EC=y
 CONFIG_CROS_EC_LPC=y
drivers/i2c/intel_i2c.c +24 -0
index 1082d1a..3d777ff 100644
@@ -9,6 +9,7 @@
 #include <dm.h>
 #include <i2c.h>
 #include <asm/io.h>
+#include <asm/arch/pch.h>
 
 int intel_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, int nmsgs)
 {
@@ -27,6 +28,29 @@ int intel_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
 
 static int intel_i2c_probe(struct udevice *dev)
 {
+	/*
+	 * So far this is just setup code for ivybridge SMbus. When we have
+	 * a full I2C driver this may need to be moved, generalised or made
+	 * dependant on a particular compatible string.
+	 *
+	 * Set SMBus I/O base
+	 */
+	dm_pci_write_config32(dev, SMB_BASE,
+			      SMBUS_IO_BASE | PCI_BASE_ADDRESS_SPACE_IO);
+
+	/* Set SMBus enable. */
+	dm_pci_write_config8(dev, HOSTC, HST_EN);
+
+	/* Set SMBus I/O space enable. */
+	dm_pci_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO);
+
+	/* Disable interrupt generation. */
+	outb(0, SMBUS_IO_BASE + SMBHSTCTL);
+
+	/* Clear any lingering errors, so transactions can run. */
+	outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+	debug("SMBus controller enabled\n");
+
 	return 0;
 }
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#97 lore raw

PATCH v2 40/55 x86: ivybridge: Use the I2C driver to perform SMbus init

Quoted 7 lines · Simon Glass

Move the init code into the I2C driver.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/cpu.c      | 39 +++------------------------------------
 arch/x86/dts/chromebook_link.dts  |  6 ++++++
 configs/chromebook_link_defconfig |  2 ++
 drivers/i2c/intel_i2c.c           | 24 ++++++++++++++++++++++++
 4 files changed, 35 insertions(+), 36 deletions(-)

applied to u-boot-x86/master, thanks!

#98 lore raw

PATCH v2 41/55 x86: ivybridge: Convert enable_usb_bar() to use DM PCI API

In reply to Simon Glass

Convert this function over to use the driver model PCI API. In this case we want to avoid using the real PCI devices since they have not yet been probed. Instead, write directly to their PCI configuration address.

---

Changes in v2:
- Avoid needing the pch device to set up the USB bar

 arch/x86/cpu/ivybridge/cpu.c | 34 +++++++++++++++++-----------------
 1 file changed, 17 insertions(+), 17 deletions(-)
arch/x86/cpu/ivybridge/cpu.c +17 -17
index b9dda4c7..948833c 100644
@@ -133,33 +133,33 @@ int arch_cpu_init_dm(void)
  *
  * This is used to speed up the resume path.
  */
-static void enable_usb_bar(void)
+static void enable_usb_bar(struct udevice *bus)
 {
 	pci_dev_t usb0 = PCH_EHCI1_DEV;
 	pci_dev_t usb1 = PCH_EHCI2_DEV;
 	pci_dev_t usb3 = PCH_XHCI_DEV;
-	u32 cmd;
+	ulong cmd;
 
 	/* USB Controller 1 */
-	x86_pci_write_config32(usb0, PCI_BASE_ADDRESS_0,
-			       PCH_EHCI0_TEMP_BAR0);
-	cmd = x86_pci_read_config32(usb0, PCI_COMMAND);
+	pci_bus_write_config(bus, usb0, PCI_BASE_ADDRESS_0,
+			     PCH_EHCI0_TEMP_BAR0, PCI_SIZE_32);
+	pci_bus_read_config(bus, usb0, PCI_COMMAND, &cmd, PCI_SIZE_32);
 	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
-	x86_pci_write_config32(usb0, PCI_COMMAND, cmd);
+	pci_bus_write_config(bus, usb0, PCI_COMMAND, cmd, PCI_SIZE_32);
 
-	/* USB Controller 1 */
-	x86_pci_write_config32(usb1, PCI_BASE_ADDRESS_0,
-			       PCH_EHCI1_TEMP_BAR0);
-	cmd = x86_pci_read_config32(usb1, PCI_COMMAND);
+	/* USB Controller 2 */
+	pci_bus_write_config(bus, usb1, PCI_BASE_ADDRESS_0,
+			     PCH_EHCI1_TEMP_BAR0, PCI_SIZE_32);
+	pci_bus_read_config(bus, usb1, PCI_COMMAND, &cmd, PCI_SIZE_32);
 	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
-	x86_pci_write_config32(usb1, PCI_COMMAND, cmd);
+	pci_bus_write_config(bus, usb1, PCI_COMMAND, cmd, PCI_SIZE_32);
 
-	/* USB3 Controller */
-	x86_pci_write_config32(usb3, PCI_BASE_ADDRESS_0,
-			       PCH_XHCI_TEMP_BAR0);
-	cmd = x86_pci_read_config32(usb3, PCI_COMMAND);
+	/* USB3 Controller 1 */
+	pci_bus_write_config(bus, usb3, PCI_BASE_ADDRESS_0,
+			     PCH_XHCI_TEMP_BAR0, PCI_SIZE_32);
+	pci_bus_read_config(bus, usb3, PCI_COMMAND, &cmd, PCI_SIZE_32);
 	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
-	x86_pci_write_config32(usb3, PCI_COMMAND, cmd);
+	pci_bus_write_config(bus, usb3, PCI_COMMAND, cmd, PCI_SIZE_32);
 }
 
 static int report_bist_failure(void)
@@ -244,7 +244,7 @@ int print_cpuinfo(void)
 
 	/* Prepare USB controller early in S3 resume */
 	if (boot_mode == PEI_BOOT_RESUME)
-		enable_usb_bar();
+		enable_usb_bar(pci_get_controller(lpc->parent));
 
 	gd->arch.pei_boot_mode = boot_mode;
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#99 lore raw

PATCH v2 41/55 x86: ivybridge: Convert enable_usb_bar() to use DM PCI API

Quoted 6 lines · Simon Glass

Convert this function over to use the driver model PCI API. In this case we want to avoid using the real PCI devices since they have not yet been probed. Instead, write directly to their PCI configuration address.

Quoted 8 lines

---

Changes in v2:
- Avoid needing the pch device to set up the USB bar

 arch/x86/cpu/ivybridge/cpu.c | 34 +++++++++++++++++-----------------
 1 file changed, 17 insertions(+), 17 deletions(-)

applied to u-boot-x86/master, thanks!

#100 lore raw

PATCH v2 42/55 x86: ivybridge: Convert dram_init() to use DM PCI API

In reply to Simon Glass

Convert the top part of the DRAM init to use the driver model PCI API. Further work will complete the transformation.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/sdram.c | 39 +++++++++++++++++++++++++--------------
 1 file changed, 25 insertions(+), 14 deletions(-)
arch/x86/cpu/ivybridge/sdram.c +25 -14
index 4372a5c..5c1b788 100644
@@ -495,8 +495,10 @@ static int add_memory_area(struct memory_info *info,
  *
  * This is a bit complicated since on x86 there are system memory holes all
  * over the place. We create a list of available memory blocks
+ *
+ * @dev:	Northbridge device
  */
-static int sdram_find(pci_dev_t dev)
+static int sdram_find(struct udevice *dev)
 {
 	struct memory_info *info = &gd->arch.meminfo;
 	uint32_t tseg_base, uma_size, tolud;
@@ -505,6 +507,7 @@ static int sdram_find(pci_dev_t dev)
 	uint64_t uma_memory_size;
 	unsigned long long tomk;
 	uint16_t ggc;
+	u32 val;
 
 	/* Total Memory 2GB example:
 	 *
@@ -533,24 +536,27 @@ static int sdram_find(pci_dev_t dev)
 	 */
 
 	/* Top of Upper Usable DRAM, including remap */
-	touud = x86_pci_read_config32(dev, TOUUD+4);
-	touud <<= 32;
-	touud |= x86_pci_read_config32(dev, TOUUD);
+	dm_pci_read_config32(dev, TOUUD + 4, &val);
+	touud = (uint64_t)val << 32;
+	dm_pci_read_config32(dev, TOUUD, &val);
+	touud |= val;
 
 	/* Top of Lower Usable DRAM */
-	tolud = x86_pci_read_config32(dev, TOLUD);
+	dm_pci_read_config32(dev, TOLUD, &tolud);
 
 	/* Top of Memory - does not account for any UMA */
-	tom = x86_pci_read_config32(dev, 0xa4);
-	tom <<= 32;
-	tom |= x86_pci_read_config32(dev, 0xa0);
+	dm_pci_read_config32(dev, 0xa4, &val);
+	tom = (uint64_t)val << 32;
+	dm_pci_read_config32(dev, 0xa0, &val);
+	tom |= val;
 
 	debug("TOUUD %llx TOLUD %08x TOM %llx\n", touud, tolud, tom);
 
 	/* ME UMA needs excluding if total memory <4GB */
-	me_base = x86_pci_read_config32(dev, 0x74);
-	me_base <<= 32;
-	me_base |= x86_pci_read_config32(dev, 0x70);
+	dm_pci_read_config32(dev, 0x74, &val);
+	me_base = (uint64_t)val << 32;
+	dm_pci_read_config32(dev, 0x70, &val);
+	me_base |= val;
 
 	debug("MEBASE %llx\n", me_base);
 
@@ -568,7 +574,7 @@ static int sdram_find(pci_dev_t dev)
 	}
 
 	/* Graphics memory comes next */
-	ggc = x86_pci_read_config16(dev, GGC);
+	dm_pci_read_config16(dev, GGC, &ggc);
 	if (!(ggc & 2)) {
 		debug("IGD decoded, subtracting ");
 
@@ -588,7 +594,7 @@ static int sdram_find(pci_dev_t dev)
 	}
 
 	/* Calculate TSEG size from its base which must be below GTT */
-	tseg_base = x86_pci_read_config32(dev, 0xb8);
+	dm_pci_read_config32(dev, 0xb8, &tseg_base);
 	uma_size = (uma_memory_base - tseg_base) >> 10;
 	tomk -= uma_size;
 	uma_memory_base = tomk * 1024ULL;
@@ -723,7 +729,7 @@ int dram_init(void)
 			{ 0, 4, 0x0000 }, /* P13= Empty */
 		},
 	};
-	pci_dev_t dev = PCI_BDF(0, 0, 0);
+	struct udevice *dev;
 	int ret;
 
 	debug("Boot mode %d\n", gd->arch.pei_boot_mode);
@@ -742,6 +748,11 @@ int dram_init(void)
 
 	post_code(POST_DRAM);
 
+	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
+	if (ret)
+		return ret;
+	if (!dev)
+		return -ENODEV;
 	ret = sdram_find(dev);
 	if (ret)
 		return ret;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#101 lore raw

PATCH v2 42/55 x86: ivybridge: Convert dram_init() to use DM PCI API

Quoted 12 lines · Simon Glass

Convert the top part of the DRAM init to use the driver model PCI API. Further work will complete the transformation.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/sdram.c | 39 +++++++++++++++++++++++++--------------
 1 file changed, 25 insertions(+), 14 deletions(-)

applied to u-boot-x86/master, thanks!

#102 lore raw

PATCH v2 43/55 x86: ivybridge: Convert sdram_initialise() to use DM PCI API

In reply to Simon Glass

Convert this function to use the the driver model PCI API. We just need to pass in the northbridge device.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/sdram.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
arch/x86/cpu/ivybridge/sdram.c +10 -9
index 5c1b788..6105cc0 100644
@@ -283,9 +283,10 @@ static int recovery_mode_enabled(void)
 /**
  * Find the PEI executable in the ROM and execute it.
  *
- * @param pei_data: configuration data for UEFI PEI reference code
+ * @dev: Northbridge device
+ * @pei_data: configuration data for UEFI PEI reference code
  */
-int sdram_initialise(struct pei_data *pei_data)
+int sdram_initialise(struct udevice *dev, struct pei_data *pei_data)
 {
 	unsigned version;
 	const char *data;
@@ -374,7 +375,7 @@ int sdram_initialise(struct pei_data *pei_data)
 	 * Send ME init done for SandyBridge here.  This is done inside the
 	 * SystemAgent binary on IvyBridge
 	 */
-	done = x86_pci_read_config32(PCH_DEV, PCI_DEVICE_ID);
+	dm_pci_read_config16(dev, PCI_DEVICE_ID, &done);
 	done &= BASE_REV_MASK;
 	if (BASE_REV_SNB == done)
 		intel_early_me_init_done(ME_INIT_STATUS_SUCCESS);
@@ -732,12 +733,17 @@ int dram_init(void)
 	struct udevice *dev;
 	int ret;
 
+	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
+	if (ret)
+		return ret;
+	if (!dev)
+		return -ENODEV;
 	debug("Boot mode %d\n", gd->arch.pei_boot_mode);
 	debug("mrc_input %p\n", pei_data.mrc_input);
 	pei_data.boot_mode = gd->arch.pei_boot_mode;
 	ret = copy_spd(&pei_data);
 	if (!ret)
-		ret = sdram_initialise(&pei_data);
+		ret = sdram_initialise(dev, &pei_data);
 	if (ret)
 		return ret;
 
@@ -748,11 +754,6 @@ int dram_init(void)
 
 	post_code(POST_DRAM);
 
-	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
-	if (ret)
-		return ret;
-	if (!dev)
-		return -ENODEV;
 	ret = sdram_find(dev);
 	if (ret)
 		return ret;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#103 lore raw

PATCH v2 43/55 x86: ivybridge: Convert sdram_initialise() to use DM PCI API

Quoted 12 lines · Simon Glass

Convert this function to use the the driver model PCI API. We just need to pass in the northbridge device.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/sdram.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

applied to u-boot-x86/master, thanks!

#104 lore raw

PATCH v2 44/55 x86: chromebook_link: Enable the syscon uclass

In reply to Simon Glass

We will use a system controller to model the Intel Management Engine. Enable this for link.

---

Changes in v2: None

 configs/chromebook_link_defconfig | 2 ++
 1 file changed, 2 insertions(+)
configs/chromebook_link_defconfig +2 -0
index daa958e..f44bef7 100644
@@ -20,6 +20,8 @@ CONFIG_CMD_BOOTSTAGE=y
 CONFIG_CMD_TPM=y
 CONFIG_CMD_TPM_TEST=y
 CONFIG_OF_CONTROL=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
 CONFIG_CPU=y
 CONFIG_SYS_I2C_INTEL=y
 CONFIG_CMD_CROS_EC=y
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#105 lore raw

PATCH v2 44/55 x86: chromebook_link: Enable the syscon uclass

Quoted 12 lines · Simon Glass

We will use a system controller to model the Intel Management Engine. Enable this for link.

---

Changes in v2: None

 configs/chromebook_link_defconfig | 2 ++
 1 file changed, 2 insertions(+)

applied to u-boot-x86/master, thanks!

#106 lore raw

PATCH v2 45/55 x86: ivybridge: Convert SDRAM init to use driver model

In reply to Simon Glass

SDRAM init needs access to the Northbridge controller and the Intel Management Engine device. Add the latter to the device tree and convert all of this code to driver model.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/early_me.c        | 68 ++++++++++++++++++++------------
 arch/x86/cpu/ivybridge/sdram.c           | 20 ++++++----
 arch/x86/dts/chromebook_link.dts         |  6 +++
 arch/x86/include/asm/arch-ivybridge/me.h | 45 ++++++++++++++++++---
 4 files changed, 101 insertions(+), 38 deletions(-)
arch/x86/cpu/ivybridge/early_me.c +42 -26
index 711470f..612c910 100644
@@ -7,6 +7,7 @@
  */
 
 #include <common.h>
+#include <dm.h>
 #include <errno.h>
 #include <asm/pci.h>
 #include <asm/processor.h>
@@ -25,33 +26,36 @@ static const char *const me_ack_values[] = {
 	[ME_HFS_ACK_CONTINUE]	= "Continue to boot"
 };
 
-static inline void pci_read_dword_ptr(void *ptr, int offset)
+static inline void pci_read_dword_ptr(struct udevice *me_dev, void *ptr,
+				      int offset)
 {
 	u32 dword;
 
-	dword = x86_pci_read_config32(PCH_ME_DEV, offset);
+	dm_pci_read_config32(me_dev, offset, &dword);
 	memcpy(ptr, &dword, sizeof(dword));
 }
 
-static inline void pci_write_dword_ptr(void *ptr, int offset)
+static inline void pci_write_dword_ptr(struct udevice *me_dev, void *ptr,
+				       int offset)
 {
 	u32 dword = 0;
+
 	memcpy(&dword, ptr, sizeof(dword));
-	x86_pci_write_config32(PCH_ME_DEV, offset, dword);
+	dm_pci_write_config32(me_dev, offset, dword);
 }
 
-void intel_early_me_status(void)
+void intel_early_me_status(struct udevice *me_dev)
 {
 	struct me_hfs hfs;
 	struct me_gmes gmes;
 
-	pci_read_dword_ptr(&hfs, PCI_ME_HFS);
-	pci_read_dword_ptr(&gmes, PCI_ME_GMES);
+	pci_read_dword_ptr(me_dev, &hfs, PCI_ME_HFS);
+	pci_read_dword_ptr(me_dev, &gmes, PCI_ME_GMES);
 
 	intel_me_status(&hfs, &gmes);
 }
 
-int intel_early_me_init(void)
+int intel_early_me_init(struct udevice *me_dev)
 {
 	int count;
 	struct me_uma uma;
@@ -61,7 +65,7 @@ int intel_early_me_init(void)
 
 	/* Wait for ME UMA SIZE VALID bit to be set */
 	for (count = ME_RETRY; count > 0; --count) {
-		pci_read_dword_ptr(&uma, PCI_ME_UMA);
+		pci_read_dword_ptr(me_dev, &uma, PCI_ME_UMA);
 		if (uma.valid)
 			break;
 		udelay(ME_DELAY);
@@ -72,7 +76,7 @@ int intel_early_me_init(void)
 	}
 
 	/* Check for valid firmware */
-	pci_read_dword_ptr(&hfs, PCI_ME_HFS);
+	pci_read_dword_ptr(me_dev, &hfs, PCI_ME_HFS);
 	if (hfs.fpt_bad) {
 		printf("WARNING: ME has bad firmware\n");
 		return -EBADF;
@@ -83,11 +87,11 @@ int intel_early_me_init(void)
 	return 0;
 }
 
-int intel_early_me_uma_size(void)
+int intel_early_me_uma_size(struct udevice *me_dev)
 {
 	struct me_uma uma;
 
-	pci_read_dword_ptr(&uma, PCI_ME_UMA);
+	pci_read_dword_ptr(me_dev, &uma, PCI_ME_UMA);
 	if (uma.valid) {
 		debug("ME: Requested %uMB UMA\n", uma.size);
 		return uma.size;
@@ -97,11 +101,11 @@ int intel_early_me_uma_size(void)
 	return -EINVAL;
 }
 
-static inline void set_global_reset(int enable)
+static inline void set_global_reset(struct udevice *dev, int enable)
 {
 	u32 etr3;
 
-	etr3 = x86_pci_read_config32(PCH_LPC_DEV, ETR3);
+	dm_pci_read_config32(dev, ETR3, &etr3);
 
 	/* Clear CF9 Without Resume Well Reset Enable */
 	etr3 &= ~ETR3_CWORWRE;
@@ -112,10 +116,11 @@ static inline void set_global_reset(int enable)
 	else
 		etr3 &= ~ETR3_CF9GR;
 
-	x86_pci_write_config32(PCH_LPC_DEV, ETR3, etr3);
+	dm_pci_write_config32(dev, ETR3, etr3);
 }
 
-int intel_early_me_init_done(u8 status)
+int intel_early_me_init_done(struct udevice *dev, struct udevice *me_dev,
+			     uint status)
 {
 	int count;
 	u32 mebase_l, mebase_h;
@@ -126,8 +131,8 @@ int intel_early_me_init_done(u8 status)
 	};
 
 	/* MEBASE from MESEG_BASE[35:20] */
-	mebase_l = x86_pci_read_config32(PCH_DEV, PCI_CPU_MEBASE_L);
-	mebase_h = x86_pci_read_config32(PCH_DEV, PCI_CPU_MEBASE_H);
+	dm_pci_read_config32(PCH_DEV, PCI_CPU_MEBASE_L, &mebase_l);
+	dm_pci_read_config32(PCH_DEV, PCI_CPU_MEBASE_H, &mebase_h);
 	mebase_h &= 0xf;
 	did.uma_base = (mebase_l >> 20) | (mebase_h << 12);
 
@@ -135,25 +140,25 @@ int intel_early_me_init_done(u8 status)
 	debug("ME: Sending Init Done with status: %d, UMA base: 0x%04x\n",
 	      status, did.uma_base);
 
-	pci_write_dword_ptr(&did, PCI_ME_H_GS);
+	pci_write_dword_ptr(me_dev, &did, PCI_ME_H_GS);
 
 	/* Must wait for ME acknowledgement */
 	for (count = ME_RETRY; count > 0; --count) {
-		pci_read_dword_ptr(&hfs, PCI_ME_HFS);
+		pci_read_dword_ptr(me_dev, &hfs, PCI_ME_HFS);
 		if (hfs.bios_msg_ack)
 			break;
 		udelay(ME_DELAY);
 	}
 	if (!count) {
 		printf("ERROR: ME failed to respond\n");
-		return -1;
+		return -ETIMEDOUT;
 	}
 
 	/* Return the requested BIOS action */
 	debug("ME: Requested BIOS Action: %s\n", me_ack_values[hfs.ack_data]);
 
 	/* Check status after acknowledgement */
-	intel_early_me_status();
+	intel_early_me_status(me_dev);
 
 	switch (hfs.ack_data) {
 	case ME_HFS_ACK_CONTINUE:
@@ -161,17 +166,17 @@ int intel_early_me_init_done(u8 status)
 		return 0;
 	case ME_HFS_ACK_RESET:
 		/* Non-power cycle reset */
-		set_global_reset(0);
+		set_global_reset(dev, 0);
 		reset_cpu(0);
 		break;
 	case ME_HFS_ACK_PWR_CYCLE:
 		/* Power cycle reset */
-		set_global_reset(0);
+		set_global_reset(dev, 0);
 		x86_full_reset();
 		break;
 	case ME_HFS_ACK_GBL_RESET:
 		/* Global reset */
-		set_global_reset(1);
+		set_global_reset(dev, 1);
 		x86_full_reset();
 		break;
 	case ME_HFS_ACK_S3:
@@ -180,5 +185,16 @@ int intel_early_me_init_done(u8 status)
 		break;
 	}
 
-	return -1;
+	return -EINVAL;
 }
+
+static const struct udevice_id ivybridge_syscon_ids[] = {
+	{ .compatible = "intel,me", },
+	{ }
+};
+
+U_BOOT_DRIVER(syscon_intel_me) = {
+	.name = "intel_me_syscon",
+	.id = UCLASS_SYSCON,
+	.of_match = ivybridge_syscon_ids,
+};
arch/x86/cpu/ivybridge/sdram.c +13 -7
index 6105cc0..696351b 100644
@@ -286,7 +286,8 @@ static int recovery_mode_enabled(void)
  * @dev: Northbridge device
  * @pei_data: configuration data for UEFI PEI reference code
  */
-int sdram_initialise(struct udevice *dev, struct pei_data *pei_data)
+int sdram_initialise(struct udevice *dev, struct udevice *me_dev,
+		     struct pei_data *pei_data)
 {
 	unsigned version;
 	const char *data;
@@ -296,10 +297,10 @@ int sdram_initialise(struct udevice *dev, struct pei_data *pei_data)
 	report_platform_info();
 
 	/* Wait for ME to be ready */
-	ret = intel_early_me_init();
+	ret = intel_early_me_init(me_dev);
 	if (ret)
 		return ret;
-	ret = intel_early_me_uma_size();
+	ret = intel_early_me_uma_size(me_dev);
 	if (ret < 0)
 		return ret;
 
@@ -378,9 +379,9 @@ int sdram_initialise(struct udevice *dev, struct pei_data *pei_data)
 	dm_pci_read_config16(dev, PCI_DEVICE_ID, &done);
 	done &= BASE_REV_MASK;
 	if (BASE_REV_SNB == done)
-		intel_early_me_init_done(ME_INIT_STATUS_SUCCESS);
+		intel_early_me_init_done(dev, me_dev, ME_INIT_STATUS_SUCCESS);
 	else
-		intel_early_me_status();
+		intel_early_me_status(me_dev);
 
 	post_system_agent_init(pei_data);
 	report_memory_config();
@@ -730,7 +731,7 @@ int dram_init(void)
 			{ 0, 4, 0x0000 }, /* P13= Empty */
 		},
 	};
-	struct udevice *dev;
+	struct udevice *dev, *me_dev;
 	int ret;
 
 	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &dev);
@@ -738,12 +739,17 @@ int dram_init(void)
 		return ret;
 	if (!dev)
 		return -ENODEV;
+	ret = uclass_first_device(UCLASS_SYSCON, &me_dev);
+	if (ret)
+		return ret;
+	if (!me_dev)
+		return -ENODEV;
 	debug("Boot mode %d\n", gd->arch.pei_boot_mode);
 	debug("mrc_input %p\n", pei_data.mrc_input);
 	pei_data.boot_mode = gd->arch.pei_boot_mode;
 	ret = copy_spd(&pei_data);
 	if (!ret)
-		ret = sdram_initialise(dev, &pei_data);
+		ret = sdram_initialise(dev, me_dev, &pei_data);
 	if (ret)
 		return ret;
 
arch/x86/dts/chromebook_link.dts +6 -0
index 54f2043..329eae8 100644
@@ -220,6 +220,12 @@
 			intel,pch-backlight = <0x04000000>;
 		};
 
+		me at 16,0 {
+			reg = <0x0000b000 0 0 0 0>;
+			compatible = "intel,me";
+			u-boot,dm-pre-reloc;
+		};
+
 		pch at 1f,0 {
 			reg = <0x0000f800 0 0 0 0>;
 			compatible = "intel,bd82x6x", "intel,pch9";
arch/x86/include/asm/arch-ivybridge/me.h +40 -5

52 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#107 lore raw

PATCH v2 45/55 x86: ivybridge: Convert SDRAM init to use driver model

Quoted 8 lines · Simon Glass

SDRAM init needs access to the Northbridge controller and the Intel Management Engine device. Add the latter to the device tree and convert all of this code to driver model.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/early_me.c        | 68 ++++++++++++++++++++------------
 arch/x86/cpu/ivybridge/sdram.c           | 20 ++++++----
 arch/x86/dts/chromebook_link.dts         |  6 +++
 arch/x86/include/asm/arch-ivybridge/me.h | 45 ++++++++++++++++++---
 4 files changed, 101 insertions(+), 38 deletions(-)

applied to u-boot-x86/master, thanks!

#108 lore raw

PATCH v2 46/55 x86: ivybridge: Convert report_platform to DM PCI API

In reply to Simon Glass

Convert these functions to use the driver model PCI API.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/report_platform.c          | 11 ++++++-----
 arch/x86/cpu/ivybridge/sdram.c                    |  2 +-
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  2 +-
 3 files changed, 8 insertions(+), 7 deletions(-)
arch/x86/cpu/ivybridge/report_platform.c +6 -5
index 4493870..c78322a 100644
@@ -10,6 +10,7 @@
 #include <asm/cpu.h>
 #include <asm/pci.h>
 #include <asm/arch/pch.h>
+#include <asm/arch/sandybridge.h>
 
 static void report_cpu_info(void)
 {
@@ -63,27 +64,27 @@ static struct {
 	{0x1E5F, "NM70"},
 };
 
-static void report_pch_info(void)
+static void report_pch_info(struct udevice *dev)
 {
 	const char *pch_type = "Unknown";
 	int i;
 	u16 dev_id;
 	uint8_t rev_id;
 
-	dev_id = x86_pci_read_config16(PCH_LPC_DEV, 2);
+	dm_pci_read_config16(dev, 2, &dev_id);
 	for (i = 0; i < ARRAY_SIZE(pch_table); i++) {
 		if (pch_table[i].dev_id == dev_id) {
 			pch_type = pch_table[i].dev_name;
 			break;
 		}
 	}
-	rev_id = x86_pci_read_config8(PCH_LPC_DEV, 8);
+	dm_pci_read_config8(dev, 8, &rev_id);
 	debug("PCH type: %s, device id: %x, rev id %x\n", pch_type, dev_id,
 	      rev_id);
 }
 
-void report_platform_info(void)
+void report_platform_info(struct udevice *dev)
 {
 	report_cpu_info();
-	report_pch_info();
+	report_pch_info(dev);
 }
arch/x86/cpu/ivybridge/sdram.c +1 -1
index 696351b..3e5be4e 100644
@@ -294,7 +294,7 @@ int sdram_initialise(struct udevice *dev, struct udevice *me_dev,
 	uint16_t done;
 	int ret;
 
-	report_platform_info();
+	report_platform_info(dev);
 
 	/* Wait for ME to be ready */
 	ret = intel_early_me_init(me_dev);
arch/x86/include/asm/arch-ivybridge/sandybridge.h +1 -1
index af8a9f7..ce8d030 100644
@@ -110,7 +110,7 @@
 
 int bridge_silicon_revision(void);
 
-void report_platform_info(void);
+void report_platform_info(struct udevice *dev);
 
 void sandybridge_early_init(int chipset_type);
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#109 lore raw

PATCH v2 46/55 x86: ivybridge: Convert report_platform to DM PCI API

Quoted 4 lines · Simon Glass

Convert these functions to use the driver model PCI API.

Quoted 9 lines

---

Changes in v2: None

 arch/x86/cpu/ivybridge/report_platform.c          | 11 ++++++-----
 arch/x86/cpu/ivybridge/sdram.c                    |  2 +-
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  2 +-
 3 files changed, 8 insertions(+), 7 deletions(-)

applied to u-boot-x86/master, thanks!

#110 lore raw

PATCH v2 47/55 x86: ivybridge: Convert pch.c to use DM PCI API

In reply to Simon Glass

Convert this file to use the driver model PCI API.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c              | 10 ++++----
 arch/x86/cpu/ivybridge/pch.c              | 35 ++++++++++++++------------
 arch/x86/cpu/ivybridge/sata.c             | 21 +++++++++++-----
 arch/x86/include/asm/arch-ivybridge/pch.h | 42 +++++++++++++++++++++++++++----
 4 files changed, 76 insertions(+), 32 deletions(-)
arch/x86/cpu/ivybridge/lpc.c +5 -5
index 0cf55c5..12e86cb 100644
@@ -354,10 +354,10 @@ static void enable_clock_gating(struct udevice *pch)
 	reg16 |= (1 << 2) | (1 << 11);
 	dm_pci_write_config16(pch, GEN_PMCON_1, reg16);
 
-	pch_iobp_update(0xEB007F07, ~0UL, (1 << 31));
-	pch_iobp_update(0xEB004000, ~0UL, (1 << 7));
-	pch_iobp_update(0xEC007F07, ~0UL, (1 << 31));
-	pch_iobp_update(0xEC004000, ~0UL, (1 << 7));
+	pch_iobp_update(pch, 0xEB007F07, ~0UL, (1 << 31));
+	pch_iobp_update(pch, 0xEB004000, ~0UL, (1 << 7));
+	pch_iobp_update(pch, 0xEC007F07, ~0UL, (1 << 31));
+	pch_iobp_update(pch, 0xEC004000, ~0UL, (1 << 7));
 
 	reg32 = readl(RCB_REG(CG));
 	reg32 |= (1 << 31);
@@ -573,7 +573,7 @@ static int lpc_init_extra(struct udevice *dev)
 	pch_power_options(pch);
 
 	/* Initialize power management */
-	switch (pch_silicon_type()) {
+	switch (pch_silicon_type(pch)) {
 	case PCH_TYPE_CPT: /* CougarPoint */
 		cpt_pm_init(pch);
 		break;
arch/x86/cpu/ivybridge/pch.c +19 -16
index bbab646..c7ce408 100644
@@ -14,32 +14,34 @@
 static int pch_revision_id = -1;
 static int pch_type = -1;
 
-int pch_silicon_revision(void)
+int pch_silicon_revision(struct udevice *dev)
 {
-	pci_dev_t dev;
+	u8 val;
 
-	dev = PCH_LPC_DEV;
+	if (pch_revision_id < 0) {
+		dm_pci_read_config8(dev, PCI_REVISION_ID, &val);
+		pch_revision_id = val;
+	}
 
-	if (pch_revision_id < 0)
-		pch_revision_id = x86_pci_read_config8(dev, PCI_REVISION_ID);
 	return pch_revision_id;
 }
 
-int pch_silicon_type(void)
+int pch_silicon_type(struct udevice *dev)
 {
-	pci_dev_t dev;
+	u8 val;
 
-	dev = PCH_LPC_DEV;
+	if (pch_type < 0) {
+		dm_pci_read_config8(dev, PCI_DEVICE_ID + 1, &val);
+		pch_type = val;
+	}
 
-	if (pch_type < 0)
-		pch_type = x86_pci_read_config8(dev, PCI_DEVICE_ID + 1);
 	return pch_type;
 }
 
-int pch_silicon_supported(int type, int rev)
+int pch_silicon_supported(struct udevice *dev, int type, int rev)
 {
-	int cur_type = pch_silicon_type();
-	int cur_rev = pch_silicon_revision();
+	int cur_type = pch_silicon_type(dev);
+	int cur_rev = pch_silicon_revision(dev);
 
 	switch (type) {
 	case PCH_TYPE_CPT:
@@ -78,7 +80,8 @@ static inline int iobp_poll(void)
 	return 0;
 }
 
-void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue)
+void pch_iobp_update(struct udevice *dev, u32 address, u32 andvalue,
+		     u32 orvalue)
 {
 	u32 data;
 
@@ -86,7 +89,7 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue)
 	writel(address, RCB_REG(IOBPIRI));
 
 	/* READ OPCODE */
-	if (pch_silicon_supported(PCH_TYPE_CPT, PCH_STEP_B0))
+	if (pch_silicon_supported(dev, PCH_TYPE_CPT, PCH_STEP_B0))
 		writel(IOBPS_RW_BX, RCB_REG(IOBPS));
 	else
 		writel(IOBPS_READ_AX, RCB_REG(IOBPS));
@@ -109,7 +112,7 @@ void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue)
 	data |= orvalue;
 
 	/* WRITE OPCODE */
-	if (pch_silicon_supported(PCH_TYPE_CPT, PCH_STEP_B0))
+	if (pch_silicon_supported(dev, PCH_TYPE_CPT, PCH_STEP_B0))
 		writel(IOBPS_RW_BX, RCB_REG(IOBPS));
 	else
 		writel(IOBPS_WRITE_AX, RCB_REG(IOBPS));
arch/x86/cpu/ivybridge/sata.c +15 -6
index 21e11d1..a59d9ed 100644
@@ -51,7 +51,7 @@ static void common_sata_init(struct udevice *dev, unsigned int port_map)
 	dm_pci_write_config32(dev, 0x94, ((port_map ^ 0x3f) << 24) | 0x183);
 }
 
-static void bd82x6x_sata_init(struct udevice *dev)
+static void bd82x6x_sata_init(struct udevice *dev, struct udevice *pch)
 {
 	unsigned int port_map, speed_support, port_tx;
 	const void *blob = gd->fdt_blob;
@@ -170,11 +170,11 @@ static void bd82x6x_sata_init(struct udevice *dev)
 	/* Set Gen3 Transmitter settings if needed */
 	port_tx = fdtdec_get_int(blob, node, "intel,sata-port0-gen3-tx", 0);
 	if (port_tx)
-		pch_iobp_update(SATA_IOBP_SP0G3IR, 0, port_tx);
+		pch_iobp_update(pch, SATA_IOBP_SP0G3IR, 0, port_tx);
 
 	port_tx = fdtdec_get_int(blob, node, "intel,sata-port1-gen3-tx", 0);
 	if (port_tx)
-		pch_iobp_update(SATA_IOBP_SP1G3IR, 0, port_tx);
+		pch_iobp_update(pch, SATA_IOBP_SP1G3IR, 0, port_tx);
 
 	/* Additional Programming Requirements */
 	sir_write(dev, 0x04, 0x00001600);
@@ -199,8 +199,8 @@ static void bd82x6x_sata_init(struct udevice *dev)
 	sir_write(dev, 0xc8, 0x0c0c0c0c);
 	sir_write(dev, 0xd4, 0x10000000);
 
-	pch_iobp_update(0xea004001, 0x3fffffff, 0xc0000000);
-	pch_iobp_update(0xea00408a, 0xfffffcff, 0x00000100);
+	pch_iobp_update(pch, 0xea004001, 0x3fffffff, 0xc0000000);
+	pch_iobp_update(pch, 0xea00408a, 0xfffffcff, 0x00000100);
 }
 
 static void bd82x6x_sata_enable(struct udevice *dev)
@@ -226,10 +226,19 @@ static void bd82x6x_sata_enable(struct udevice *dev)
 
 static int bd82x6x_sata_probe(struct udevice *dev)
 {
+	struct udevice *pch;
+	int ret;
+
+	ret = uclass_first_device(UCLASS_PCH, &pch);
+	if (ret)
+		return ret;
+	if (!pch)
+		return -ENODEV;
+
 	if (!(gd->flags & GD_FLG_RELOC))
 		bd82x6x_sata_enable(dev);
 	else
-		bd82x6x_sata_init(dev);
+		bd82x6x_sata_init(dev, pch);
 
 	return 0;
 }
arch/x86/include/asm/arch-ivybridge/pch.h +37 -5

52 lines not on this page · raw message

Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#111 lore raw

PATCH v2 47/55 x86: ivybridge: Convert pch.c to use DM PCI API

Quoted 6 lines · Simon Glass

Convert this file to use the driver model PCI API.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c              | 10 ++++----
 arch/x86/cpu/ivybridge/pch.c              | 35 ++++++++++++++------------
 arch/x86/cpu/ivybridge/sata.c             | 21 +++++++++++-----
 arch/x86/include/asm/arch-ivybridge/pch.h | 42 +++++++++++++++++++++++++++----
 4 files changed, 76 insertions(+), 32 deletions(-)

applied to u-boot-x86/master, thanks!

#112 lore raw

PATCH v2 48/55 x86: ivybridge: Move code from pch.c to bd82x6x.c

In reply to Simon Glass

This code relates to the PCH, so we should move it into the same file.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile           |   1 -
 arch/x86/cpu/ivybridge/bd82x6x.c          | 129 ++++++++++++++++++++++++++++++
 arch/x86/cpu/ivybridge/pch.c              | 126 -----------------------------
 arch/x86/include/asm/arch-ivybridge/pch.h |  18 -----
 4 files changed, 129 insertions(+), 145 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/pch.c
arch/x86/cpu/ivybridge/Makefile +0 -1
index 259a5df..7007d5f 100644
@@ -14,7 +14,6 @@ obj-y += me_status.o
 obj-y += model_206ax.o
 obj-y += microcode_intel.o
 obj-y += northbridge.o
-obj-y += pch.o
 obj-y += report_platform.o
 obj-y += sata.o
 obj-y += sdram.o
arch/x86/cpu/ivybridge/bd82x6x.c +129 -0

141 lines not on this page · raw message

arch/x86/cpu/ivybridge/pch.c deleted +0 -126

126 lines not on this page · raw message

arch/x86/include/asm/arch-ivybridge/pch.h +0 -18
index 0f1aa01..af3e8e7 100644
@@ -466,14 +466,6 @@
 #define TCO2_STS	0x66
 
 /**
- * pch_silicon_revision() - Read silicon revision ID from the PCH
- *
- * @dev:	PCH device
- * @return silicon revision ID
- */
-int pch_silicon_revision(struct udevice *dev);
-
-/**
  * pch_silicon_revision() - Read silicon device ID from the PCH
  *
  * @dev:	PCH device
@@ -482,16 +474,6 @@ int pch_silicon_revision(struct udevice *dev);
 int pch_silicon_type(struct udevice *dev);
 
 /**
- * pch_silicon_supported() - Check if a certain revision is supported
- *
- * @dev:	PCH device
- * @type:	PCH type
- * @rev:	Minimum required resion
- * @return 0 if not supported, 1 if supported
- */
-int pch_silicon_supported(struct udevice *dev, int type, int rev);
-
-/**
  * pch_pch_iobp_update() - Update a pch register
  *
  * @dev:	PCH device
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#113 lore raw

PATCH v2 48/55 x86: ivybridge: Move code from pch.c to bd82x6x.c

Quoted 6 lines · Simon Glass

This code relates to the PCH, so we should move it into the same file.

---

Quoted 9 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile           |   1 -
 arch/x86/cpu/ivybridge/bd82x6x.c          | 129 ++++++++++++++++++++++++++++++
 arch/x86/cpu/ivybridge/pch.c              | 126 -----------------------------
 arch/x86/include/asm/arch-ivybridge/pch.h |  18 -----
 4 files changed, 129 insertions(+), 145 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/pch.c

applied to u-boot-x86/master, thanks!

#114 lore raw

PATCH v2 49/55 x86: ivybridge: Sort out the calls to bridge_silicon_revision()

In reply to Simon Glass

This function is called all over the place. Convert it use the driver model PCI API, and rationalise the calls.

---

Changes in v2:
- Fix incorrect bits in bridge_silicon_revision() comment

 arch/x86/cpu/ivybridge/gma.c                      | 33 ++++++++--------
 arch/x86/cpu/ivybridge/northbridge.c              | 47 +++++++++++------------
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  8 +++-
 3 files changed, 46 insertions(+), 42 deletions(-)
arch/x86/cpu/ivybridge/gma.c +17 -16
index b94536c..f9b03f2 100644
@@ -353,14 +353,13 @@ static int gtt_poll(void *bar, u32 reg, u32 mask, u32 value)
 	return 0;
 }
 
-static int gma_pm_init_pre_vbios(void *gtt_bar)
+static int gma_pm_init_pre_vbios(void *gtt_bar, int rev)
 {
 	u32 reg32;
 
-	debug("GT Power Management Init, silicon = %#x\n",
-	      bridge_silicon_revision());
+	debug("GT Power Management Init, silicon = %#x\n", rev);
 
-	if (bridge_silicon_revision() < IVB_STEP_C0) {
+	if (rev < IVB_STEP_C0) {
 		/* 1: Enable force wake */
 		gtt_write(gtt_bar, 0xa18c, 0x00000001);
 		gtt_poll(gtt_bar, 0x130090, (1 << 0), (1 << 0));
@@ -370,14 +369,14 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 		gtt_poll(gtt_bar, 0x130040, (1 << 0), (1 << 0));
 	}
 
-	if ((bridge_silicon_revision() & BASE_REV_MASK) == BASE_REV_SNB) {
+	if ((rev & BASE_REV_MASK) == BASE_REV_SNB) {
 		/* 1d: Set GTT+0x42004 [15:14]=11 (SnB C1+) */
 		reg32 = gtt_read(gtt_bar, 0x42004);
 		reg32 |= (1 << 14) | (1 << 15);
 		gtt_write(gtt_bar, 0x42004, reg32);
 	}
 
-	if (bridge_silicon_revision() >= IVB_STEP_A0) {
+	if (rev >= IVB_STEP_A0) {
 		/* Display Reset Acknowledge Settings */
 		reg32 = gtt_read(gtt_bar, 0x45010);
 		reg32 |= (1 << 1) | (1 << 0);
@@ -386,7 +385,7 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 
 	/* 2: Get GT SKU from GTT+0x911c[13] */
 	reg32 = gtt_read(gtt_bar, 0x911c);
-	if ((bridge_silicon_revision() & BASE_REV_MASK) == BASE_REV_SNB) {
+	if ((rev & BASE_REV_MASK) == BASE_REV_SNB) {
 		if (reg32 & (1 << 13)) {
 			debug("SNB GT1 Power Meter Weights\n");
 			gtt_write_powermeter(gtt_bar, snb_pm_gt1);
@@ -435,13 +434,13 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 	reg32 = gtt_read(gtt_bar, 0xa180);
 	reg32 |= (1 << 26) | (1 << 31);
 	/* (bit 20=1 for SNB step D1+ / IVB A0+) */
-	if (bridge_silicon_revision() >= SNB_STEP_D1)
+	if (rev >= SNB_STEP_D1)
 		reg32 |= (1 << 20);
 	gtt_write(gtt_bar, 0xa180, reg32);
 
 	/* 6a: for SnB step D2+ only */
-	if (((bridge_silicon_revision() & BASE_REV_MASK) == BASE_REV_SNB) &&
-	    (bridge_silicon_revision() >= SNB_STEP_D2)) {
+	if (((rev & BASE_REV_MASK) == BASE_REV_SNB) &&
+	    (rev >= SNB_STEP_D2)) {
 		reg32 = gtt_read(gtt_bar, 0x9400);
 		reg32 |= (1 << 7);
 		gtt_write(gtt_bar, 0x9400, reg32);
@@ -453,7 +452,7 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 		gtt_poll(gtt_bar, 0x941c, (1 << 1), (0 << 1));
 	}
 
-	if ((bridge_silicon_revision() & BASE_REV_MASK) == BASE_REV_IVB) {
+	if ((rev & BASE_REV_MASK) == BASE_REV_IVB) {
 		reg32 = gtt_read(gtt_bar, 0x907c);
 		reg32 |= (1 << 16);
 		gtt_write(gtt_bar, 0x907c, reg32);
@@ -505,7 +504,7 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 	gtt_write(gtt_bar, 0xa070, 0x0000000a); /* RP Idle Hysteresis */
 
 	/* 11a: Enable Render Standby (RC6) */
-	if ((bridge_silicon_revision() & BASE_REV_MASK) == BASE_REV_IVB) {
+	if ((rev & BASE_REV_MASK) == BASE_REV_IVB) {
 		/*
 		 * IvyBridge should also support DeepRenderStandby.
 		 *
@@ -539,14 +538,14 @@ static int gma_pm_init_pre_vbios(void *gtt_bar)
 	return 0;
 }
 
-int gma_pm_init_post_vbios(void *gtt_bar, const void *blob, int node)
+int gma_pm_init_post_vbios(int rev, void *gtt_bar, const void *blob, int node)
 {
 	u32 reg32, cycle_delay;
 
 	debug("GT Power Management Init (post VBIOS)\n");
 
 	/* 15: Deassert Force Wake */
-	if (bridge_silicon_revision() < IVB_STEP_C0) {
+	if (rev < IVB_STEP_C0) {
 		gtt_write(gtt_bar, 0xa18c, gtt_read(gtt_bar, 0xa18c) & ~1);
 		gtt_poll(gtt_bar, 0x130090, (1 << 0), (0 << 0));
 	} else {
@@ -805,6 +804,7 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 	ulong base;
 	u32 reg32;
 	int ret;
+	int rev;
 
 	/* Enable PCH Display Port */
 	writew(0x0010, RCB_REG(DISPBDF));
@@ -813,6 +813,7 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 	ret = uclass_first_device(UCLASS_NORTHBRIDGE, &nbridge);
 	if (!nbridge)
 		return -ENODEV;
+	rev = bridge_silicon_revision(nbridge);
 	sandybridge_setup_graphics(nbridge, dev);
 
 	/* IGD needs to be Bus Master */
@@ -827,7 +828,7 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 
 	gtt_bar = (void *)dm_pci_read_bar32(dev, 0);
 	debug("GT bar %p\n", gtt_bar);
-	ret = gma_pm_init_pre_vbios(gtt_bar);
+	ret = gma_pm_init_pre_vbios(gtt_bar, rev);
 	if (ret)
 		return ret;
 
@@ -838,7 +839,7 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 	debug("BIOS ran in %lums\n", get_timer(start));
 #endif
 	/* Post VBIOS init */
-	ret = gma_pm_init_post_vbios(gtt_bar, blob, node);
+	ret = gma_pm_init_post_vbios(rev, gtt_bar, blob, node);
 	if (ret)
 		return ret;
 
arch/x86/cpu/ivybridge/northbridge.c +22 -25

100 lines not on this page · raw message

arch/x86/include/asm/arch-ivybridge/sandybridge.h +7 -1
index ce8d030..d137d67 100644
@@ -108,7 +108,13 @@
 
 #define DMIBAR_REG(x)	(DEFAULT_DMIBAR + x)
 
-int bridge_silicon_revision(void);
+/**
+ * bridge_silicon_revision() - Get the Northbridge revision
+ *
+ * @dev:	Northbridge device
+ * @return revision ID (bits 3:0) and bridge ID (bits 7:4)
+ */
+int bridge_silicon_revision(struct udevice *dev);
 
 void report_platform_info(struct udevice *dev);
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#115 lore raw

PATCH v2 49/55 x86: ivybridge: Sort out the calls to bridge_silicon_revision()

Quoted 6 lines · Simon Glass

This function is called all over the place. Convert it use the driver model PCI API, and rationalise the calls.

---

Quoted 8 lines

Changes in v2:
- Fix incorrect bits in bridge_silicon_revision() comment

 arch/x86/cpu/ivybridge/gma.c                      | 33 ++++++++--------
 arch/x86/cpu/ivybridge/northbridge.c              | 47 +++++++++++------------
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  8 +++-
 3 files changed, 46 insertions(+), 42 deletions(-)
#116 lore raw

PATCH v2 49/55 x86: ivybridge: Sort out the calls to bridge_silicon_revision()

Quoted 10 lines · Bin Meng
Quoted 9 lines · Simon Glass

This function is called all over the place. Convert it use the driver model PCI API, and rationalise the calls.

---

Changes in v2:
- Fix incorrect bits in bridge_silicon_revision() comment

Quoted 7 lines
Quoted 5 lines
 arch/x86/cpu/ivybridge/gma.c                      | 33 ++++++++--------
 arch/x86/cpu/ivybridge/northbridge.c              | 47 +++++++++++------------
 arch/x86/include/asm/arch-ivybridge/sandybridge.h |  8 +++-
 3 files changed, 46 insertions(+), 42 deletions(-)

applied to u-boot-x86/master, thanks!

#117 lore raw

PATCH v2 50/55 x86: ivybridge: Drop special EHCI init

In reply to Simon Glass

This is not needed. On reset wake-on-disconnect is already set. It may a problem during a soft reset or resume, but for now it does not seem important. Also drop the command register update since PCI auto-config does it for us.

---

Changes in v2:
- Rename from 'Convert EHCI init to use the DM PCI API'
- Drop this init
- Fix the USB PCI address in the device tree

 arch/x86/cpu/ivybridge/Makefile               |  1 -
 arch/x86/cpu/ivybridge/bd82x6x.c              |  3 ---
 arch/x86/cpu/ivybridge/usb_ehci.c             | 29 ---------------------------
 arch/x86/dts/chromebook_link.dts              | 12 +++++++++++
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 12 insertions(+), 34 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/usb_ehci.c
arch/x86/cpu/ivybridge/Makefile +0 -1
index 7007d5f..ac41853 100644
@@ -17,5 +17,4 @@ obj-y += northbridge.o
 obj-y += report_platform.o
 obj-y += sata.o
 obj-y += sdram.o
-obj-y += usb_ehci.o
 obj-y += usb_xhci.o
arch/x86/cpu/ivybridge/bd82x6x.c +0 -3
index 70a0aea..2591b20 100644
@@ -159,9 +159,6 @@ static int bd82x6x_probe(struct udevice *dev)
 	/* Cause the SATA device to do its init */
 	uclass_first_device(UCLASS_DISK, &dev);
 
-	bd82x6x_usb_ehci_init(PCH_EHCI1_DEV);
-	bd82x6x_usb_ehci_init(PCH_EHCI2_DEV);
-
 	gma_node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_GMA);
 	if (gma_node < 0) {
 		debug("%s: Cannot find GMA node\n", __func__);
arch/x86/cpu/ivybridge/usb_ehci.c deleted +0 -29
deleted file mode 100644
index da11aee..0000000
@@ -1,29 +0,0 @@
-/*
- * From Coreboot
- * Copyright (C) 2008-2009 coresystems GmbH
- *
- * SPDX-License-Identifier:	GPL-2.0
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/pci.h>
-#include <asm/arch/pch.h>
-
-void bd82x6x_usb_ehci_init(pci_dev_t dev)
-{
-	u32 reg32;
-
-	/* Disable Wake on Disconnect in RMH */
-	reg32 = readl(RCB_REG(0x35b0));
-	reg32 |= 0x22;
-	writel(reg32, RCB_REG(0x35b0));
-
-	debug("EHCI: Setting up controller.. ");
-	reg32 = x86_pci_read_config32(dev, PCI_COMMAND);
-	reg32 |= PCI_COMMAND_MASTER;
-	/* reg32 |= PCI_COMMAND_SERR; */
-	x86_pci_write_config32(dev, PCI_COMMAND, reg32);
-
-	debug("done.\n");
-}
arch/x86/dts/chromebook_link.dts +12 -0
index 329eae8..662e5d9 100644
@@ -12,6 +12,8 @@
 
 	aliases {
 		spi0 = "/pci/pch/spi";
+		usb0 = &usb_0;
+		usb1 = &usb_1;
 	};
 
 	config {
@@ -226,6 +228,16 @@
 			u-boot,dm-pre-reloc;
 		};
 
+		usb_1: usb at 1a,0 {
+			reg = <0x0000d000 0 0 0 0>;
+			compatible = "ehci-pci";
+		};
+
+		usb_0: usb at 1d,0 {
+			reg = <0x0000e800 0 0 0 0>;
+			compatible = "ehci-pci";
+		};
+
 		pch at 1f,0 {
 			reg = <0x0000f800 0 0 0 0>;
 			compatible = "intel,bd82x6x", "intel,pch9";
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index bb3a6c9..5959717 100644
@@ -7,7 +7,6 @@
 #ifndef _ASM_ARCH_BD82X6X_H
 #define _ASM_ARCH_BD82X6X_H
 
-void bd82x6x_usb_ehci_init(pci_dev_t dev);
 void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
 
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#118 lore raw

PATCH v2 50/55 x86: ivybridge: Drop special EHCI init

Quoted 13 lines · Simon Glass

This is not needed. On reset wake-on-disconnect is already set. It may a problem during a soft reset or resume, but for now it does not seem important. Also drop the command register update since PCI auto-config does it for us.

---

Changes in v2:
- Rename from 'Convert EHCI init to use the DM PCI API'
- Drop this init
- Fix the USB PCI address in the device tree

Quoted 8 lines
 arch/x86/cpu/ivybridge/Makefile               |  1 -
 arch/x86/cpu/ivybridge/bd82x6x.c              |  3 ---
 arch/x86/cpu/ivybridge/usb_ehci.c             | 29 ---------------------------
 arch/x86/dts/chromebook_link.dts              | 12 +++++++++++
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 12 insertions(+), 34 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/usb_ehci.c
#119 lore raw

PATCH v2 50/55 x86: ivybridge: Drop special EHCI init

Quoted 23 lines · Bin Meng
Quoted 13 lines · Simon Glass

This is not needed. On reset wake-on-disconnect is already set. It may a problem during a soft reset or resume, but for now it does not seem important. Also drop the command register update since PCI auto-config does it for us.

---

Changes in v2:
- Rename from 'Convert EHCI init to use the DM PCI API'
- Drop this init
- Fix the USB PCI address in the device tree

Quoted 8 lines
 arch/x86/cpu/ivybridge/Makefile               |  1 -
 arch/x86/cpu/ivybridge/bd82x6x.c              |  3 ---
 arch/x86/cpu/ivybridge/usb_ehci.c             | 29 ---------------------------
 arch/x86/dts/chromebook_link.dts              | 12 +++++++++++
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 5 files changed, 12 insertions(+), 34 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/usb_ehci.c
Quoted 1 line

applied to u-boot-x86/master, thanks!

#120 lore raw

PATCH v2 51/55 x86: ivybridge: Drop XHCI support

In reply to Simon Glass

This is not used on link which is the only ivybridge board. Drop this code.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile               |  1 -
 arch/x86/cpu/ivybridge/usb_xhci.c             | 32 ---------------------------
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 34 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/usb_xhci.c
arch/x86/cpu/ivybridge/Makefile +0 -1
index ac41853..45ef141 100644
@@ -17,4 +17,3 @@ obj-y += northbridge.o
 obj-y += report_platform.o
 obj-y += sata.o
 obj-y += sdram.o
-obj-y += usb_xhci.o
arch/x86/cpu/ivybridge/usb_xhci.c deleted +0 -32
deleted file mode 100644
index f77b804..0000000
@@ -1,32 +0,0 @@
-/*
- * From Coreboot
- * Copyright (C) 2008-2009 coresystems GmbH
- *
- * SPDX-License-Identifier:	GPL-2.0
- */
-
-#include <common.h>
-#include <asm/pci.h>
-#include <asm/arch/pch.h>
-
-void bd82x6x_usb_xhci_init(pci_dev_t dev)
-{
-	u32 reg32;
-
-	debug("XHCI: Setting up controller.. ");
-
-	/* lock overcurrent map */
-	reg32 = x86_pci_read_config32(dev, 0x44);
-	reg32 |= 1;
-	x86_pci_write_config32(dev, 0x44, reg32);
-
-	/* Enable clock gating */
-	reg32 = x86_pci_read_config32(dev, 0x40);
-	reg32 &= ~((1 << 20) | (1 << 21));
-	reg32 |= (1 << 19) | (1 << 18) | (1 << 17);
-	reg32 |= (1 << 10) | (1 << 9) | (1 << 8);
-	reg32 |= (1 << 31); /* lock */
-	x86_pci_write_config32(dev, 0x40, reg32);
-
-	debug("done.\n");
-}
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +0 -1
index 5959717..2607da6 100644
@@ -7,7 +7,6 @@
 #ifndef _ASM_ARCH_BD82X6X_H
 #define _ASM_ARCH_BD82X6X_H
 
-void bd82x6x_usb_xhci_init(pci_dev_t dev);
 int gma_func0_init(struct udevice *dev, const void *blob, int node);
 
 #endif
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#121 lore raw

PATCH v2 51/55 x86: ivybridge: Drop XHCI support

Quoted 6 lines · Simon Glass

This is not used on link which is the only ivybridge board. Drop this code.

---

Quoted 8 lines

Changes in v2: None

 arch/x86/cpu/ivybridge/Makefile               |  1 -
 arch/x86/cpu/ivybridge/usb_xhci.c             | 32 ---------------------------
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  1 -
 3 files changed, 34 deletions(-)
 delete mode 100644 arch/x86/cpu/ivybridge/usb_xhci.c

applied to u-boot-x86/master, thanks!

#122 lore raw

PATCH v2 52/55 x86: ivybridge: Drop the SMM-locking code

In reply to Simon Glass

U-Boot does not support SMM yet, so we can drop this code. It is easy to bring back when needed.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c | 57 --------------------------------------------
 1 file changed, 57 deletions(-)
arch/x86/cpu/ivybridge/lpc.c +0 -57
index 12e86cb..9ab5ed3 100644
@@ -379,59 +379,6 @@ static void enable_clock_gating(struct udevice *pch)
 	setbits_le32(RCB_REG(0x3564), 0x3);
 }
 
-#if CONFIG_HAVE_SMI_HANDLER
-static void pch_lock_smm(pci_dev_t dev)
-{
-#if TEST_SMM_FLASH_LOCKDOWN
-	u8 reg8;
-#endif
-
-	if (acpi_slp_type != 3) {
-#if ENABLE_ACPI_MODE_IN_COREBOOT
-		debug("Enabling ACPI via APMC:\n");
-		outb(0xe1, 0xb2); /* Enable ACPI mode */
-		debug("done.\n");
-#else
-		debug("Disabling ACPI via APMC:\n");
-		outb(0x1e, 0xb2); /* Disable ACPI mode */
-		debug("done.\n");
-#endif
-	}
-
-	/* Don't allow evil boot loaders, kernels, or
-	 * userspace applications to deceive us:
-	 */
-	smm_lock();
-
-#if TEST_SMM_FLASH_LOCKDOWN
-	/* Now try this: */
-	debug("Locking BIOS to RO... ");
-	reg8 = x86_pci_read_config8(dev, 0xdc);	/* BIOS_CNTL */
-	debug(" BLE: %s; BWE: %s\n", (reg8 & 2) ? "on" : "off",
-	      (reg8 & 1) ? "rw" : "ro");
-	reg8 &= ~(1 << 0);			/* clear BIOSWE */
-	x86_pci_write_config8(dev, 0xdc, reg8);
-	reg8 |= (1 << 1);			/* set BLE */
-	x86_pci_write_config8(dev, 0xdc, reg8);
-	debug("ok.\n");
-	reg8 = x86_pci_read_config8(dev, 0xdc);	/* BIOS_CNTL */
-	debug(" BLE: %s; BWE: %s\n", (reg8 & 2) ? "on" : "off",
-	      (reg8 & 1) ? "rw" : "ro");
-
-	debug("Writing:\n");
-	writeb(0, 0xfff00000);
-	debug("Testing:\n");
-	reg8 |= (1 << 0);			/* set BIOSWE */
-	x86_pci_write_config8(dev, 0xdc, reg8);
-
-	reg8 = x86_pci_read_config8(dev, 0xdc);	/* BIOS_CNTL */
-	debug(" BLE: %s; BWE: %s\n", (reg8 & 2) ? "on" : "off",
-	      (reg8 & 1) ? "rw" : "ro");
-	debug("Done.\n");
-#endif
-}
-#endif
-
 static void pch_disable_smm_only_flashing(struct udevice *pch)
 {
 	u8 reg8;
@@ -596,10 +543,6 @@ static int lpc_init_extra(struct udevice *dev)
 
 	pch_disable_smm_only_flashing(pch);
 
-#if CONFIG_HAVE_SMI_HANDLER
-	pch_lock_smm(dev);
-#endif
-
 	pch_fixups(pch);
 
 	return 0;
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#123 lore raw

PATCH v2 52/55 x86: ivybridge: Drop the SMM-locking code

Quoted 12 lines · Simon Glass

U-Boot does not support SMM yet, so we can drop this code. It is easy to bring back when needed.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/lpc.c | 57 --------------------------------------------
 1 file changed, 57 deletions(-)

applied to u-boot-x86/master, thanks!

#124 lore raw

PATCH v2 53/55 x86: Set up a shared syscon numbering schema

In reply to Simon Glass

Each system controller can have a number to identify it. It can then be accessed using syscon_get_by_driver_data(). Put this in a shared header file and update the only current user.

---

Changes in v2:
- Enable SYSCON and REGMAP for panther to avoid a build error

 arch/x86/cpu/ivybridge/early_me.c   | 3 ++-
 arch/x86/cpu/ivybridge/sdram.c      | 6 +++---
 arch/x86/include/asm/cpu.h          | 9 +++++++++
 configs/chromebox_panther_defconfig | 2 ++
 4 files changed, 16 insertions(+), 4 deletions(-)
arch/x86/cpu/ivybridge/early_me.c +2 -1
index 612c910..f0d6899 100644
@@ -10,6 +10,7 @@
 #include <dm.h>
 #include <errno.h>
 #include <asm/pci.h>
+#include <asm/cpu.h>
 #include <asm/processor.h>
 #include <asm/arch/me.h>
 #include <asm/arch/pch.h>
@@ -189,7 +190,7 @@ int intel_early_me_init_done(struct udevice *dev, struct udevice *me_dev,
 }
 
 static const struct udevice_id ivybridge_syscon_ids[] = {
-	{ .compatible = "intel,me", },
+	{ .compatible = "intel,me", .data = X86_SYSCON_ME },
 	{ }
 };
 
arch/x86/cpu/ivybridge/sdram.c +3 -3
index 3e5be4e..e23c422 100644
@@ -18,6 +18,8 @@
 #include <rtc.h>
 #include <spi.h>
 #include <spi_flash.h>
+#include <syscon.h>
+#include <asm/cpu.h>
 #include <asm/processor.h>
 #include <asm/gpio.h>
 #include <asm/global_data.h>
@@ -739,11 +741,9 @@ int dram_init(void)
 		return ret;
 	if (!dev)
 		return -ENODEV;
-	ret = uclass_first_device(UCLASS_SYSCON, &me_dev);
+	ret = syscon_get_by_driver_data(X86_SYSCON_ME, &me_dev);
 	if (ret)
 		return ret;
-	if (!me_dev)
-		return -ENODEV;
 	debug("Boot mode %d\n", gd->arch.pei_boot_mode);
 	debug("mrc_input %p\n", pei_data.mrc_input);
 	pei_data.boot_mode = gd->arch.pei_boot_mode;
arch/x86/include/asm/cpu.h +9 -0
index c70183c..76cdf47 100644
@@ -45,6 +45,15 @@ enum {
 	GDT_BASE_HIGH_MASK	= 0xf,
 };
 
+/*
+ * System controllers in an x86 system. We mostly need to just find these and
+ * use them on PCI. At some point these might have their own uclass.
+ */
+enum {
+	X86_NONE,
+	X86_SYSCON_ME,		/* Intel Management Engine */
+};
+
 struct cpuid_result {
 	uint32_t eax;
 	uint32_t ebx;
configs/chromebox_panther_defconfig +2 -0
index 4b78292..bb6c5d4 100644
@@ -16,6 +16,8 @@ CONFIG_CMD_BOOTSTAGE=y
 CONFIG_CMD_TPM=y
 CONFIG_CMD_TPM_TEST=y
 CONFIG_OF_CONTROL=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
 CONFIG_CMD_CROS_EC=y
 CONFIG_CROS_EC=y
 CONFIG_CROS_EC_LPC=y
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#125 lore raw

PATCH v2 53/55 x86: Set up a shared syscon numbering schema

Quoted 8 lines · Simon Glass

Each system controller can have a number to identify it. It can then be accessed using syscon_get_by_driver_data(). Put this in a shared header file and update the only current user.

---

Quoted 9 lines

Changes in v2:
- Enable SYSCON and REGMAP for panther to avoid a build error

 arch/x86/cpu/ivybridge/early_me.c   | 3 ++-
 arch/x86/cpu/ivybridge/sdram.c      | 6 +++---
 arch/x86/include/asm/cpu.h          | 9 +++++++++
 configs/chromebox_panther_defconfig | 2 ++
 4 files changed, 16 insertions(+), 4 deletions(-)

applied to u-boot-x86/master, thanks!

#126 lore raw

PATCH v2 54/55 x86: ivybridge: Use syscon for the GMA device

In reply to Simon Glass

Until we have a proper video uclass we can use syscon to handle the GMA device, and avoid the special device tree and PCI searching. Update the code to work this way.

---

Changes in v2: None

 arch/x86/cpu/ivybridge/bd82x6x.c              | 14 +++++---------
 arch/x86/cpu/ivybridge/early_me.c             |  1 +
 arch/x86/cpu/ivybridge/gma.c                  |  8 +++++---
 arch/x86/dts/chromebook_link.dts              |  3 ++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  2 +-
 arch/x86/include/asm/cpu.h                    |  4 +++-
 6 files changed, 17 insertions(+), 15 deletions(-)
arch/x86/cpu/ivybridge/bd82x6x.c +5 -9
index 2591b20..2b172d4 100644
@@ -9,6 +9,8 @@
 #include <fdtdec.h>
 #include <malloc.h>
 #include <pch.h>
+#include <syscon.h>
+#include <asm/cpu.h>
 #include <asm/io.h>
 #include <asm/lapic.h>
 #include <asm/pci.h>
@@ -149,8 +151,7 @@ void pch_iobp_update(struct udevice *dev, u32 address, u32 andvalue,
 
 static int bd82x6x_probe(struct udevice *dev)
 {
-	const void *blob = gd->fdt_blob;
-	int gma_node;
+	struct udevice *gma_dev;
 	int ret;
 
 	if (!(gd->flags & GD_FLG_RELOC))
@@ -159,15 +160,10 @@ static int bd82x6x_probe(struct udevice *dev)
 	/* Cause the SATA device to do its init */
 	uclass_first_device(UCLASS_DISK, &dev);
 
-	gma_node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_GMA);
-	if (gma_node < 0) {
-		debug("%s: Cannot find GMA node\n", __func__);
-		return -EINVAL;
-	}
-	ret = dm_pci_bus_find_bdf(PCH_VIDEO_DEV, &dev);
+	ret = syscon_get_by_driver_data(X86_SYSCON_GMA, &gma_dev);
 	if (ret)
 		return ret;
-	ret = gma_func0_init(dev, blob, gma_node);
+	ret = gma_func0_init(gma_dev);
 	if (ret)
 		return ret;
 
arch/x86/cpu/ivybridge/early_me.c +1 -0
index f0d6899..b1df77d 100644
@@ -191,6 +191,7 @@ int intel_early_me_init_done(struct udevice *dev, struct udevice *me_dev,
 
 static const struct udevice_id ivybridge_syscon_ids[] = {
 	{ .compatible = "intel,me", .data = X86_SYSCON_ME },
+	{ .compatible = "intel,gma", .data = X86_SYSCON_GMA },
 	{ }
 };
 
arch/x86/cpu/ivybridge/gma.c +5 -3
index f9b03f2..3b6291e 100644
@@ -538,8 +538,10 @@ static int gma_pm_init_pre_vbios(void *gtt_bar, int rev)
 	return 0;
 }
 
-int gma_pm_init_post_vbios(int rev, void *gtt_bar, const void *blob, int node)
+int gma_pm_init_post_vbios(struct udevice *dev, int rev, void *gtt_bar)
 {
+	const void *blob = gd->fdt_blob;
+	int node = dev->of_offset;
 	u32 reg32, cycle_delay;
 
 	debug("GT Power Management Init (post VBIOS)\n");
@@ -794,7 +796,7 @@ void sandybridge_setup_graphics(struct udevice *dev, struct udevice *video_dev)
 	writel(reg32, MCHBAR_REG(0x5418));
 }
 
-int gma_func0_init(struct udevice *dev, const void *blob, int node)
+int gma_func0_init(struct udevice *dev)
 {
 #ifdef CONFIG_VIDEO
 	ulong start;
@@ -839,7 +841,7 @@ int gma_func0_init(struct udevice *dev, const void *blob, int node)
 	debug("BIOS ran in %lums\n", get_timer(start));
 #endif
 	/* Post VBIOS init */
-	ret = gma_pm_init_post_vbios(rev, gtt_bar, blob, node);
+	ret = gma_pm_init_post_vbios(dev, rev, gtt_bar);
 	if (ret)
 		return ret;
 
arch/x86/dts/chromebook_link.dts +2 -1
index 662e5d9..d148d6e 100644
@@ -209,7 +209,8 @@
 			u-boot,dm-pre-reloc;
 		};
 
-		gma {
+		gma at 2,0 {
+			reg = <0x00001000 0 0 0 0>;
 			compatible = "intel,gma";
 			intel,dp_hotplug = <0 0 0x06>;
 			intel,panel-port-select = <1>;
arch/x86/include/asm/arch-ivybridge/bd82x6x.h +1 -1
index 2607da6..e866580 100644
@@ -7,6 +7,6 @@
 #ifndef _ASM_ARCH_BD82X6X_H
 #define _ASM_ARCH_BD82X6X_H
 
-int gma_func0_init(struct udevice *dev, const void *blob, int node);
+int gma_func0_init(struct udevice *dev);
 
 #endif
arch/x86/include/asm/cpu.h +3 -1
index 76cdf47..18b0345 100644
@@ -47,11 +47,13 @@ enum {
 
 /*
  * System controllers in an x86 system. We mostly need to just find these and
- * use them on PCI. At some point these might have their own uclass.
+ * use them on PCI. At some point these might have their own uclass (e.g.
+ * UCLASS_VIDEO for the GMA device).
  */
 enum {
 	X86_NONE,
 	X86_SYSCON_ME,		/* Intel Management Engine */
+	X86_SYSCON_GMA,		/* Intel Graphics Media Accelerator */
 };
 
 struct cpuid_result {
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#127 lore raw

PATCH v2 54/55 x86: ivybridge: Use syscon for the GMA device

Quoted 10 lines · Simon Glass

Until we have a proper video uclass we can use syscon to handle the GMA device, and avoid the special device tree and PCI searching. Update the code to work this way.

---

Changes in v2: None

Quoted 8 lines
 arch/x86/cpu/ivybridge/bd82x6x.c              | 14 +++++---------
 arch/x86/cpu/ivybridge/early_me.c             |  1 +
 arch/x86/cpu/ivybridge/gma.c                  |  8 +++++---
 arch/x86/dts/chromebook_link.dts              |  3 ++-
 arch/x86/include/asm/arch-ivybridge/bd82x6x.h |  2 +-
 arch/x86/include/asm/cpu.h                    |  4 +++-
 6 files changed, 17 insertions(+), 15 deletions(-)

applied to u-boot-x86/master, thanks!

#128 lore raw

PATCH v2 55/55 x86: fdt: Drop the unused compatible strings in fdtdec

In reply to Simon Glass

We have drivers for several more devices now, so drop the strings which are no-longer used.

---

Changes in v2:
- Drop bd82x6x_pci_init() function and associated DM-conversion patch
- Drop LPC init method an 'Add an init() method to the LPC uclass' patch

 arch/x86/cpu/ivybridge/lpc.c | 6 ------
 include/fdtdec.h             | 5 -----
 lib/fdtdec.c                 | 5 -----
 3 files changed, 16 deletions(-)
arch/x86/cpu/ivybridge/lpc.c +0 -6
index 9ab5ed3..deda2f5 100644
@@ -491,8 +491,6 @@ static int lpc_early_init(struct udevice *dev)
 static int lpc_init_extra(struct udevice *dev)
 {
 	struct udevice *pch = dev->parent;
-	const void *blob = gd->fdt_blob;
-	int node;
 
 	debug("pch: lpc_init\n");
 	dm_pci_write_bar32(pch, 0, 0);
@@ -501,10 +499,6 @@ static int lpc_init_extra(struct udevice *dev)
 	dm_pci_write_bar32(pch, 3, 0x800);
 	dm_pci_write_bar32(pch, 4, 0x900);
 
-	node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_PCH);
-	if (node < 0)
-		return -ENOENT;
-
 	/* Set the value for PCI command register. */
 	dm_pci_write_config16(pch, PCI_COMMAND, 0x000f);
 
include/fdtdec.h +0 -5
index 27b350e..e545866 100644
@@ -155,15 +155,10 @@ enum fdt_compat_id {
 	COMPAT_SAMSUNG_EXYNOS_SYSMMU,	/* Exynos sysmmu */
 	COMPAT_INTEL_MICROCODE,		/* Intel microcode update */
 	COMPAT_MEMORY_SPD,		/* Memory SPD information */
-	COMPAT_INTEL_PANTHERPOINT_AHCI,	/* Intel Pantherpoint AHCI */
-	COMPAT_INTEL_MODEL_206AX,	/* Intel Model 206AX CPU */
-	COMPAT_INTEL_GMA,		/* Intel Graphics Media Accelerator */
 	COMPAT_AMS_AS3722,		/* AMS AS3722 PMIC */
-	COMPAT_INTEL_ICH_SPI,		/* Intel ICH7/9 SPI controller */
 	COMPAT_INTEL_QRK_MRC,		/* Intel Quark MRC */
 	COMPAT_INTEL_X86_PINCTRL,	/* Intel ICH7/9 pin control */
 	COMPAT_SOCIONEXT_XHCI,		/* Socionext UniPhier xHCI */
-	COMPAT_INTEL_PCH,		/* Intel PCH */
 	COMPAT_INTEL_IRQ_ROUTER,	/* Intel Interrupt Router */
 	COMPAT_ALTERA_SOCFPGA_DWMAC,	/* SoCFPGA Ethernet controller */
 	COMPAT_ALTERA_SOCFPGA_DWMMC,	/* SoCFPGA DWMMC controller */
lib/fdtdec.c +0 -5
index b50d105..3c05559 100644
@@ -60,15 +60,10 @@ static const char * const compat_names[COMPAT_COUNT] = {
 	COMPAT(SAMSUNG_EXYNOS_SYSMMU, "samsung,sysmmu-v3.3"),
 	COMPAT(INTEL_MICROCODE, "intel,microcode"),
 	COMPAT(MEMORY_SPD, "memory-spd"),
-	COMPAT(INTEL_PANTHERPOINT_AHCI, "intel,pantherpoint-ahci"),
-	COMPAT(INTEL_MODEL_206AX, "intel,model-206ax"),
-	COMPAT(INTEL_GMA, "intel,gma"),
 	COMPAT(AMS_AS3722, "ams,as3722"),
-	COMPAT(INTEL_ICH_SPI, "intel,ich-spi"),
 	COMPAT(INTEL_QRK_MRC, "intel,quark-mrc"),
 	COMPAT(INTEL_X86_PINCTRL, "intel,x86-pinctrl"),
 	COMPAT(SOCIONEXT_XHCI, "socionext,uniphier-xhci"),
-	COMPAT(COMPAT_INTEL_PCH, "intel,bd82x6x"),
 	COMPAT(COMPAT_INTEL_IRQ_ROUTER, "intel,irq-router"),
 	COMPAT(ALTERA_SOCFPGA_DWMAC, "altr,socfpga-stmmac"),
 	COMPAT(ALTERA_SOCFPGA_DWMMC, "altr,socfpga-dw-mshc"),
Signature · 1 line
2.6.0.rc2.230.g3dd15c0
#129 lore raw

PATCH v2 55/55 x86: fdt: Drop the unused compatible strings in fdtdec

Hi Simon,

Quoted 7 lines · Simon Glass

We have drivers for several more devices now, so drop the strings which are no-longer used.

---

Quoted 9 lines

Changes in v2:
- Drop bd82x6x_pci_init() function and associated DM-conversion patch
- Drop LPC init method an 'Add an init() method to the LPC uclass' patch

 arch/x86/cpu/ivybridge/lpc.c | 6 ------
 include/fdtdec.h             | 5 -----
 lib/fdtdec.c                 | 5 -----
 3 files changed, 16 deletions(-)

This patch does not apply on existing u-boot-x86/master. I tried to rebase u-boot-x86/master on top of latest u-boot/master, but it still does not apply. Please rebase this patch on top of current u-boot-x86/master and submit a new version. Thanks!

Regards,
Bin