PS3 controller (SIXAXIS) never gets into "IdleTimeout"
Hello,
I want to use my PS3 controller on my Linux system. This, so far, seems to work pretty well, but if I forget to turn off the controller when leaving my PC, then the battery keeps discharging until it is finally empty.
There is a setting "IdleTimeout" in "input.conf", but at least for me this doesn't work for the PS3 controller.
I think the reason is, that the controller keeps sending information even if it is placed on my desk and noone is touching it. If I run "evtest" on the event device, created for the controller, then I get something like this (only short snippet):
Event: time 1453228629.616457, -------------- SYN_REPORT ------------
Event: time 1453228629.651514, type 3 (EV_ABS), code 1 (ABS_Y), value 124
Event: time 1453228629.651514, type 3 (EV_ABS), code 61 (ABS_MT_TOOL_Y), value 491
Event: time 1453228629.651514, -------------- SYN_REPORT ------------
Event: time 1453228629.683436, type 3 (EV_ABS), code 1 (ABS_Y), value 123
Event: time 1453228629.683436, type 3 (EV_ABS), code 2 (ABS_Z), value 132
Event: time 1453228629.683436, type 3 (EV_ABS), code 61 (ABS_MT_TOOL_Y), value 490
Event: time 1453228629.683436, -------------- SYN_REPORT ------------
Seems like the controller keeps sending axis information even if the axis aren't touched at all.
Is there any chance to add some handling into bluez to get the controller disabled, even if it keeps sending information in "idle state"?
Thank you very much in advance.
Best regards,
Manuel
Quoted 2 lines · On Tue, 19 Jan 2016 19:57:46 +0100 Manuel Reimer <[email protected]>…
Hello,
Hi Manuel,
Quoted 23 lines
I want to use my PS3 controller on my Linux system. This, so far, seems to work pretty well, but if I forget to turn off the controller when leaving my PC, then the battery keeps discharging until it is finally empty.
There is a setting "IdleTimeout" in "input.conf", but at least for me this doesn't work for the PS3 controller.
I think the reason is, that the controller keeps sending information even if it is placed on my desk and noone is touching it. If I run "evtest" on the event device, created for the controller, then I get something like this (only short snippet):
Event: time 1453228629.616457, --------------
SYN_REPORT------------
Event: time 1453228629.651514, type 3 (EV_ABS), code 1 (ABS_Y), value 124
Event: time 1453228629.651514, type 3 (EV_ABS), code 61 (ABS_MT_TOOL_Y), value 491
Event: time 1453228629.651514, --------------SYN_REPORT------------
Event: time 1453228629.683436, type 3 (EV_ABS), code 1 (ABS_Y), value 123
Event: time 1453228629.683436, type 3 (EV_ABS), code 2 (ABS_Z), value 132
Event: time 1453228629.683436, type 3 (EV_ABS), code 61 (ABS_MT_TOOL_Y), value 490
Event: time 1453228629.683436, --------------SYN_REPORT------------
Quoted 3 lines
Seems like the controller keeps sending axis information even if the axis aren't touched at all.
IIRC this is because the controller has a lot of axes and they end up in the multi touch range (ABS_MT_*) which apparently sends event continuously.
I remember I did some experiments about remapping the axes to a more meaningful setup and there were some improvements but that work depended on some experimental changes to the linux input layer from David Herrmann (the ABS2 proposal) and I do not know if the latter ever reached mainline. This is a linux-input topic BTW.
Quoted 3 lines
Is there any chance to add some handling into bluez to get the controller disabled, even if it keeps sending information in "idle state"?
If you disconnect the device from bluez (either from an applet or from command line) the sixaxis should turn off.
JFYI a possible hardware way is to keep pushed the PS button for some seconds, this also should turn the sixaxis off.
Ciao ciao,
Antonio
Signature · 6 lines
Antonio Ospite http://ao2.it A: Because it messes up the order in which people normally read text. See http://en.wikipedia.org/wiki/Posting_style Q: Why is top-posting such a bad thing?
Quoted 8 lines · Antonio Ospite
Quoted 3 lines
Seems like the controller keeps sending axis information even if the axis aren't touched at all.
IIRC this is because the controller has a lot of axes and they end up in the multi touch range (ABS_MT_*) which apparently sends event continuously.
Quoted 5 lines
I remember I did some experiments about remapping the axes to a more meaningful setup and there were some improvements but that work depended on some experimental changes to the linux input layer from David Herrmann (the ABS2 proposal) and I do not know if the latter ever reached mainline. This is a linux-input topic BTW.
I guess that those are just the numbers, used by Sony, directly sent out, right?
Quoted 5 lines
If you disconnect the device from bluez (either from an applet or from command line) the sixaxis should turn off.
JFYI a possible hardware way is to keep pushed the PS button for some seconds, this also should turn the sixaxis off.
Both ways work. Thank you.
Just to be sure if this is not another linux-input topic:
If I first connect my PS3 controller via bluetooth, then all LEDs are turned off after some flashing. I think a better default configuration would be to set the first LED to be on. If all are off it is not obvious that the controller is turned on...
Thanks in advance
Best regards,
Manuel