ARM: dts: cm-t335: add peripherals - part 2
cover ARM: dts: cm-t335: add peripherals - part 2
Add support for the following peripherals:
- CAN BUS
- Touchscreen
- Audio
Uri Mashiach (3):
ARM: dts: cm-t335: Add support for CAN bus
ARM: dts: cm-t335: add touchscreen support
ARM: dts: cm-t335: add audio support
arch/arm/boot/dts/am335x-cm-t335.dts | 116 +++++++++++++++++++++++++++++++++++ 1 file changed, 116 insertions(+)
Signature · 1 line
2.5.0
PATCH 1/3 ARM: dts: cm-t335: Add support for CAN bus
Add CAN bus pinmux.
Enable D_CAN bus controllers 0 and 1
The pinmux of uart1 node contradicts the pinmux of dcan0 and dcan1 nodes. U-Boot should delete the uart1 or dcan0/1 nodes.
--- arch/arm/boot/dts/am335x-cm-t335.dts | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/boot/dts/am335x-cm-t335.dts +30 -0
@@ -144,6 +144,24 @@ >; }; + dcan0_pins: pinmux_dcan0_pins { + pinctrl-single,pins = < + /* uart1_ctsn.dcan0_tx */ + AM33XX_IOPAD(0x978, PIN_OUTPUT | MUX_MODE2) + /* uart1_rtsn.dcan0_rx */ + AM33XX_IOPAD(0x97C, PIN_INPUT | MUX_MODE2) + >; + }; + + dcan1_pins: pinmux_dcan1_pins { + pinctrl-single,pins = < + /* uart1_rxd.dcan1_tx */ + AM33XX_IOPAD(0x980, PIN_OUTPUT | MUX_MODE2) + /* uart1_txd.dcan1_rx */ + AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE2) + >; + }; + ecap0_pins: pinmux_ecap0_pins { pinctrl-single,pins = < /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
@@ -448,3 +466,15 @@ status = "okay"; vwlan-supply = <&vwlan_fixed>; }; }; + +&dcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dcan0_pins>; +}; + +&dcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dcan1_pins>; +};
Signature · 1 line
2.5.0
PATCH 2/3 ARM: dts: cm-t335: add touchscreen support
In reply to Uri MashiachTouchscreen and analog digital converter configurations.
--- arch/arm/boot/dts/am335x-cm-t335.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
arch/arm/boot/dts/am335x-cm-t335.dts +17 -0
@@ -478,3 +478,20 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&dcan1_pins>; }; + +/* Touschscreen and analog digital converter */ +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x01 0x10 0x23 0x32>; + ti,charge-delay = <0x400>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; +}; +
Signature · 1 line
2.5.0
PATCH 3/3 ARM: dts: cm-t335: add audio support
In reply to Uri MashiachThe TLV320AIC23B codec is connected to the CPU by McASP controller 1 for data and I2C0 for control.
Modifications:
- Enable and configure McASP controller 1.
- Add TLV320AIC23B codec pinmux.
- Add TLV320AIC23B codec configurations.
- Use simple-audio-card as CPU to codec glue.
--- arch/arm/boot/dts/am335x-cm-t335.dts | 69 ++++++++++++++++++++++++++++++++++++ 1 file changed, 69 insertions(+)
arch/arm/boot/dts/am335x-cm-t335.dts +69 -0
@@ -56,6 +56,36 @@ brightness-levels = <0 51 53 56 62 75 101 152 255>; default-brightness-level = <8>; }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "cm-t335"; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Headphone", "Headphone Jack"; + + simple-audio-card,routing = + "Headphone Jack", "LHPOUT", + "Headphone Jack", "RHPOUT", + "LLINEIN", "Line In", + "RLINEIN", "Line In", + "MICIN", "Mic Jack"; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound_master>; + simple-audio-card,frame-master = <&sound_master>; + + simple-audio-card,cpu { + sound-dai = <&mcasp1>; + }; + + sound_master: simple-audio-card,codec { + sound-dai = <&tlv320aic23>; + system-clock-frequency = <12000000>; + }; + }; }; &am33xx_pinmux {
@@ -283,6 +313,20 @@ AM33XX_IOPAD(0x9b4, PIN_OUTPUT | MUX_MODE7) >; }; + + /* TLV320AIC23B codec */ + mcasp1_pins: pinmux_mcasp1_pins { + pinctrl-single,pins = < + /* MII1_CRS.mcasp1_aclkx */ + AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4) + /* MII1_RX_ER.mcasp1_fsx */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4) + /* MII1_COL.mcasp1_axr2 */ + AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE4) + /* RMII1_REF_CLK.mcasp1_axr3 */ + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4) + >; + }; }; &uart0 {
@@ -317,6 +361,13 @@ status = "okay"; compatible = "emmicro,em3027"; reg = <0x56>; }; + /* Audio codec */ + tlv320aic23: codec at 1a { + compatible = "ti,tlv320aic23"; + reg = <0x1a>; + #sound-dai-cells= <0>; + status = "okay"; + }; }; &usb {
@@ -495,3 +546,21 @@ status = "okay"; }; }; +/* CPU audio */ +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp1_pins>; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 16 serializers */ + num-serializer = <16>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 2 1 0 0 0 0 0 0 0 0 0 0 0 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; + + #sound-dai-cells= <0>; + status = "okay"; +};
Signature · 1 line
2.5.0
cover ARM: dts: cm-t335: add peripherals - part 2
In reply to Uri MashiachGentle ping
Quoted 13 lines · Uri Mashiach
Add support for the following peripherals:
- CAN BUS
- Touchscreen
- AudioUri Mashiach (3):
ARM: dts: cm-t335: Add support for CAN bus
ARM: dts: cm-t335: add touchscreen support
ARM: dts: cm-t335: add audio supportarch/arm/boot/dts/am335x-cm-t335.dts | 116 +++++++++++++++++++++++++++++++++++ 1 file changed, 116 insertions(+)
Signature · 2 lines
Regards, Uri
cover ARM: dts: cm-t335: add peripherals - part 2
Quoted 15 lines · Uri Mashiach
Gentle ping
Quoted 12 lines · Uri Mashiach
Add support for the following peripherals:
- CAN BUS
- Touchscreen
- AudioUri Mashiach (3):
ARM: dts: cm-t335: Add support for CAN bus
ARM: dts: cm-t335: add touchscreen support
ARM: dts: cm-t335: add audio supportarch/arm/boot/dts/am335x-cm-t335.dts | 116 +++++++++++++++++++++++++++++++++++ 1 file changed, 116 insertions(+)
Sorry for the delay, I was waiting forv4.5-rc1 and have most fixes out of the way first. Applying into omap-for-v4.6/dt.
Regards,
Tony