Skip to contentSkip to conversation

drm/i915/skl: Fix typo in DPLL_CFGCR1 definition

PATCH Applied Lyude 3 participants 3 messages Feb 4, 2016 – Feb 9, 2016

Subsystems (2)
lore
Share & tools
lore

Lyude

author
#0 lore raw

PATCH 1/1 drm/i915/skl: Fix typo in DPLL_CFGCR1 definition

We accidentally point both cfgcr registers for the second shared DPLL to the same location in i915_reg.h. This results in a lot of hw pipe state mismatches whenever we try to do a modeset that requires allocating the DPLL to a CRTC:

[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)

This usually ends up causing blank monitors, since the DPLL never can get set to the right clock.

Fixes f0f59a00a1 ("drm/i915: Type safe register read/write")
---
 drivers/gpu/drm/i915/i915_reg.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_reg.h +1 -1
index 007ae83..b9a564b 100644
@@ -7514,7 +7514,7 @@ enum skl_disp_power_wells {
 #define  DPLL_CFGCR2_PDIV_7 (4<<2)
 #define  DPLL_CFGCR2_CENTRAL_FREQ_MASK	(3)
 
-#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR2)
+#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR1)
 #define DPLL_CFGCR2(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR2, _DPLL2_CFGCR2)
 
 /* BXT display engine PLL */
Signature · 6 lines
2.5.0

_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
Reviewed-by on v1 1/1
#1 lore raw
Quoted 5 lines · Lyude

We accidentally point both cfgcr registers for the second shared DPLL to the same location in i915_reg.h. This results in a lot of hw pipe state mismatches whenever we try to do a modeset that requires allocating the DPLL to a CRTC:

Quoted 8 lines

[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)

This usually ends up causing blank monitors, since the DPLL never can get set to the right clock.

Fixes f0f59a00a1 ("drm/i915: Type safe register read/write")

Actually

Fixes 086f8e84a085 ("drm/i915: Prefix raw register defines with underscore")

That's the second regression from the type safety stuff :( I guess we still don't have enough testing coverage since this has gone undetected for so long.

Quoted 25 lines
---
 drivers/gpu/drm/i915/i915_reg.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_reg.h +1 -1
index 007ae83..b9a564b 100644
@@ -7514,7 +7514,7 @@ enum skl_disp_power_wells {
 #define  DPLL_CFGCR2_PDIV_7 (4<<2)
 #define  DPLL_CFGCR2_CENTRAL_FREQ_MASK	(3)
 
-#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR2)
+#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR1)
 #define DPLL_CFGCR2(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR2, _DPLL2_CFGCR2)
 
 /* BXT display engine PLL */
Signature · 6 lines
2.5.0

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw
Quoted 15 lines · Ville Syrjälä
Quoted 5 lines · Lyude

We accidentally point both cfgcr registers for the second shared DPLL to the same location in i915_reg.h. This results in a lot of hw pipe state mismatches whenever we try to do a modeset that requires allocating the DPLL to a CRTC:

Quoted 8 lines

[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500) [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)

This usually ends up causing blank monitors, since the DPLL never can get set to the right clock.

Fixes f0f59a00a1 ("drm/i915: Type safe register read/write")
Quoted 8 lines

Actually

Fixes 086f8e84a085 ("drm/i915: Prefix raw register defines with underscore")

That's the second regression from the type safety stuff :( I guess we still don't have enough testing coverage since this has gone undetected for so long.

Queued for -next, thanks for the patch.
-Daniel

Quoted 34 lines
Quoted 26 lines
---
 drivers/gpu/drm/i915/i915_reg.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_reg.h +1 -1
index 007ae83..b9a564b 100644
@@ -7514,7 +7514,7 @@ enum skl_disp_power_wells {
 #define  DPLL_CFGCR2_PDIV_7 (4<<2)
 #define  DPLL_CFGCR2_CENTRAL_FREQ_MASK	(3)
 
-#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR2)
+#define DPLL_CFGCR1(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR1, _DPLL2_CFGCR1)
 #define DPLL_CFGCR2(id)	_MMIO_PIPE((id) - SKL_DPLL1, _DPLL1_CFGCR2, _DPLL2_CFGCR2)
 
 /* BXT display engine PLL */
Signature · 6 lines
2.5.0

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx