Skip to contentSkip to conversation

dmaengine: sun6i: Upgrade for audio transfers

PATCH Superseded Jean-Francois Moine 2 participants 7 messages Apr 22, 2016 – Apr 26, 2016

Subsystems (2)

v5 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v5 cover dmaengine: sun6i: Upgrade for audio transfers

This patch series contains most of the required changes to the sun6i DMA driver for audio streaming (tested in
a Allwinner H3 - Orange PI 2).
It is based on the previous series 'dmaengine: sun6i: Fixes' (2016-04-22).
The lacking patch (Add 4 as a possible burst value for H3) will be submitted when a consensus with Maxime Ripard will be found.

v5
- fix checkpatch error (Vinod Koul)
v4
- remove 'Add 4 as a possible burst value for H3'
(no consensus yet)
- remove 'Simplify some macros' (Maxime Ripard)
- remove 'Compact a bit some config constants' (not critical)
- split 'lli setting' into 'simplify' and 'default burst and bus width' (Maxime Ripard)
v3
- do some optimizations
- add a check about the maxburst value '4' (Maxime Ripard)
- remove the driver fixes
v2 (comments from Vinod Koul and Sergei Shtylyov - thanks)
- typo fixes
- change some comments
- better handling of burst and bus width
- remove useless code in the cyclic capability patch

Jean-Francois Moine (3):
dmaengine: sun6i: Simplify lli setting
dmaengine: sun6i: Set default maxburst size and bus width
dmaengine: sun6i: Add cyclic capability

 drivers/dma/sun6i-dma.c | 246 ++++++++++++++++++++++++++++++++++++------------
 1 file changed, 184 insertions(+), 62 deletions(-)
Signature · 1 line
2.8.1
#1 lore raw

PATCH v5 1/3 dmaengine: sun6i: Simplify lli setting

Checking the DMA config before setting the lli list avoids to do tests inside the setting loop.

---
 drivers/dma/sun6i-dma.c | 102 ++++++++++++++++++++++--------------------------
 1 file changed, 47 insertions(+), 55 deletions(-)
drivers/dma/sun6i-dma.c +47 -55
index 3579ee7..b08245e 100644
@@ -276,45 +276,6 @@ static void *sun6i_dma_lli_add(struct sun6i_dma_lli *prev,
 	return next;
 }
 
-static inline int sun6i_dma_cfg_lli(struct sun6i_dma_lli *lli,
-				    dma_addr_t src,
-				    dma_addr_t dst, u32 len,
-				    struct dma_slave_config *config)
-{
-	s8 src_width, dst_width, src_burst, dst_burst;
-
-	if (!config)
-		return -EINVAL;
-
-	src_burst = convert_burst(config->src_maxburst);
-	if (src_burst < 0)
-		return src_burst;
-
-	dst_burst = convert_burst(config->dst_maxburst);
-	if (dst_burst < 0)
-		return dst_burst;
-
-	src_width = convert_buswidth(config->src_addr_width);
-	if (src_width < 0)
-		return src_width;
-
-	dst_width = convert_buswidth(config->dst_addr_width);
-	if (dst_width < 0)
-		return dst_width;
-
-	lli->cfg = DMA_CHAN_CFG_SRC_BURST(src_burst) |
-		DMA_CHAN_CFG_SRC_WIDTH(src_width) |
-		DMA_CHAN_CFG_DST_BURST(dst_burst) |
-		DMA_CHAN_CFG_DST_WIDTH(dst_width);
-
-	lli->src = src;
-	lli->dst = dst;
-	lli->len = len;
-	lli->para = NORMAL_WAIT;
-
-	return 0;
-}
-
 static inline void sun6i_dma_dump_lli(struct sun6i_vchan *vchan,
 				      struct sun6i_dma_lli *lli)
 {
@@ -502,6 +463,35 @@ static irqreturn_t sun6i_dma_interrupt(int irq, void *dev_id)
 	return ret;
 }
 
+static int set_config(struct sun6i_dma_dev *sdev,
+			struct dma_slave_config *sconfig,
+			enum dma_transfer_direction direction,
+			u32 *p_cfg)
+{
+	s8 src_width, dst_width, src_burst, dst_burst;
+
+	src_burst = convert_burst(sconfig->src_maxburst);
+	src_width = convert_buswidth(sconfig->src_addr_width);
+	dst_burst = convert_burst(sconfig->dst_maxburst);
+	dst_width = convert_buswidth(sconfig->dst_addr_width);
+
+	if (src_burst < 0)
+		return src_burst;
+	if (src_width < 0)
+		return src_width;
+	if (dst_burst < 0)
+		return dst_burst;
+	if (dst_width < 0)
+		return dst_width;
+
+	*p_cfg = DMA_CHAN_CFG_SRC_BURST(src_burst) |
+		DMA_CHAN_CFG_SRC_WIDTH(src_width) |
+		DMA_CHAN_CFG_DST_BURST(dst_burst) |
+		DMA_CHAN_CFG_DST_WIDTH(dst_width);
+
+	return 0;
+}
+
 static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_memcpy(
 		struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 		size_t len, unsigned long flags)
@@ -569,6 +559,7 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 	struct sun6i_desc *txd;
 	struct scatterlist *sg;
 	dma_addr_t p_lli;
+	u32 lli_cfg;
 	int i, ret;
 
 	if (!sgl)
@@ -579,6 +570,12 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 		return NULL;
 	}
 
+	ret = set_config(sdev, sconfig, dir, &lli_cfg);
+	if (ret) {
+		dev_err(chan2dev(chan), "Invalid DMA configuration\n");
+		return NULL;
+	}
+
 	txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
 	if (!txd)
 		return NULL;
@@ -588,14 +585,14 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 		if (!v_lli)
 			goto err_lli_free;
 
-		if (dir == DMA_MEM_TO_DEV) {
-			ret = sun6i_dma_cfg_lli(v_lli, sg_dma_address(sg),
-						sconfig->dst_addr, sg_dma_len(sg),
-						sconfig);
-			if (ret)
-				goto err_cur_lli_free;
+		v_lli->len = sg_dma_len(sg);
+		v_lli->para = NORMAL_WAIT;
 
-			v_lli->cfg |= DMA_CHAN_CFG_DST_IO_MODE |
+		if (dir == DMA_MEM_TO_DEV) {
+			v_lli->src = sg_dma_address(sg);
+			v_lli->dst = sconfig->dst_addr;
+			v_lli->cfg = lli_cfg |
+				DMA_CHAN_CFG_DST_IO_MODE |
 				DMA_CHAN_CFG_SRC_LINEAR_MODE |
 				DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
 				DMA_CHAN_CFG_DST_DRQ(vchan->port);
@@ -607,13 +604,10 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 				sg_dma_len(sg), flags);
 
 		} else {
-			ret = sun6i_dma_cfg_lli(v_lli, sconfig->src_addr,
-						sg_dma_address(sg), sg_dma_len(sg),
-						sconfig);
-			if (ret)
-				goto err_cur_lli_free;
-
-			v_lli->cfg |= DMA_CHAN_CFG_DST_LINEAR_MODE |
+			v_lli->src = sconfig->src_addr;
+			v_lli->dst = sg_dma_address(sg);
+			v_lli->cfg = lli_cfg |
+				DMA_CHAN_CFG_DST_LINEAR_MODE |
 				DMA_CHAN_CFG_SRC_IO_MODE |
 				DMA_CHAN_CFG_DST_DRQ(DRQ_SDRAM) |
 				DMA_CHAN_CFG_SRC_DRQ(vchan->port);
@@ -634,8 +628,6 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 
 	return vchan_tx_prep(&vchan->vc, &txd->vd, flags);
 
-err_cur_lli_free:
-	dma_pool_free(sdev->pool, v_lli, p_lli);
 err_lli_free:
 	for (prev = txd->v_lli; prev; prev = prev->v_lli_next)
 		dma_pool_free(sdev->pool, prev, virt_to_phys(prev));
Signature · 1 line
2.8.1
Applied
#2 lore raw

PATCH v5 1/3 dmaengine: sun6i: Simplify lli setting

Quoted 2 lines · Jean-Francois Moine

Checking the DMA config before setting the lli list avoids to do tests inside the setting loop.

Applied, thanks

Signature · 1 line
~Vinod
#3 lore raw

PATCH v5 2/3 dmaengine: sun6i: Set default maxburst size and bus width

In reply to Jean-Francois Moine

Some DMA clients, as audio, don't set the maxburst size and bus width on the memory side when starting DMA transfers.
This patch prevents such transfers to be aborted by providing system default values to the lacking ones.

---
 drivers/dma/sun6i-dma.c | 23 +++++++++++++++++++----
 1 file changed, 19 insertions(+), 4 deletions(-)
drivers/dma/sun6i-dma.c +19 -4
index b08245e..821fc4f 100644
@@ -470,10 +470,25 @@ static int set_config(struct sun6i_dma_dev *sdev,
 {
 	s8 src_width, dst_width, src_burst, dst_burst;
 
-	src_burst = convert_burst(sconfig->src_maxburst);
-	src_width = convert_buswidth(sconfig->src_addr_width);
-	dst_burst = convert_burst(sconfig->dst_maxburst);
-	dst_width = convert_buswidth(sconfig->dst_addr_width);
+	if (direction == DMA_MEM_TO_DEV) {
+		src_burst = convert_burst(sconfig->src_maxburst ?
+					sconfig->src_maxburst : 8);
+		src_width = convert_buswidth(sconfig->src_addr_width !=
+						DMA_SLAVE_BUSWIDTH_UNDEFINED ?
+				sconfig->src_addr_width :
+				DMA_SLAVE_BUSWIDTH_4_BYTES);
+		dst_burst = convert_burst(sconfig->dst_maxburst);
+		dst_width = convert_buswidth(sconfig->dst_addr_width);
+	} else {	/* DMA_DEV_TO_MEM */
+		src_burst = convert_burst(sconfig->src_maxburst);
+		src_width = convert_buswidth(sconfig->src_addr_width);
+		dst_burst = convert_burst(sconfig->dst_maxburst ?
+					sconfig->dst_maxburst : 8);
+		dst_width = convert_buswidth(sconfig->dst_addr_width !=
+						DMA_SLAVE_BUSWIDTH_UNDEFINED ?
+				sconfig->dst_addr_width :
+				DMA_SLAVE_BUSWIDTH_4_BYTES);
+	}
 
 	if (src_burst < 0)
 		return src_burst;
Signature · 1 line
2.8.1
#4 lore raw

PATCH v5 2/3 dmaengine: sun6i: Set default maxburst size and bus width

Quoted 22 lines · Jean-Francois Moine

Some DMA clients, as audio, don't set the maxburst size and bus width on the memory side when starting DMA transfers.
This patch prevents such transfers to be aborted by providing system default values to the lacking ones.

---
 drivers/dma/sun6i-dma.c | 23 +++++++++++++++++++----
 1 file changed, 19 insertions(+), 4 deletions(-)
drivers/dma/sun6i-dma.c +0 -4
index b08245e..821fc4f 100644
@@ -470,10 +470,25 @@ static int set_config(struct sun6i_dma_dev *sdev,
 {
 	s8 src_width, dst_width, src_burst, dst_burst;
 
-	src_burst = convert_burst(sconfig->src_maxburst);
-	src_width = convert_buswidth(sconfig->src_addr_width);
-	dst_burst = convert_burst(sconfig->dst_maxburst);
-	dst_width = convert_buswidth(sconfig->dst_addr_width);

drivers/dma/sun6i-dma.c static int set_config(struct sun6i_dma_dev *sdev, · line 482

Quoted 10 lines
drivers/dma/sun6i-dma.c +10 -0
+	if (direction == DMA_MEM_TO_DEV) {
+		src_burst = convert_burst(sconfig->src_maxburst ?
+					sconfig->src_maxburst : 8);
+		src_width = convert_buswidth(sconfig->src_addr_width !=
+						DMA_SLAVE_BUSWIDTH_UNDEFINED ?
+				sconfig->src_addr_width :
+				DMA_SLAVE_BUSWIDTH_4_BYTES);
+		dst_burst = convert_burst(sconfig->dst_maxburst);
+		dst_width = convert_buswidth(sconfig->dst_addr_width);
+	} else {	/* DMA_DEV_TO_MEM */

Else can be any other direction, I would prefer we check that. Also swicth would be better

Quoted 12 lines
drivers/dma/sun6i-dma.c +9 -0
+		src_burst = convert_burst(sconfig->src_maxburst);
+		src_width = convert_buswidth(sconfig->src_addr_width);
+		dst_burst = convert_burst(sconfig->dst_maxburst ?
+					sconfig->dst_maxburst : 8);
+		dst_width = convert_buswidth(sconfig->dst_addr_width !=
+						DMA_SLAVE_BUSWIDTH_UNDEFINED ?
+				sconfig->dst_addr_width :
+				DMA_SLAVE_BUSWIDTH_4_BYTES);
+	}
 
 	if (src_burst < 0)
 		return src_burst;
Signature · 1 line
~Vinod
#5 lore raw

PATCH v5 3/3 dmaengine: sun6i: Add cyclic capability

In reply to Jean-Francois Moine

DMA cyclic transfers are required by audio streaming.

---
 drivers/dma/sun6i-dma.c | 129 +++++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 122 insertions(+), 7 deletions(-)
drivers/dma/sun6i-dma.c +122 -7
index 821fc4f..f0c4a53 100644
@@ -146,6 +146,8 @@ struct sun6i_vchan {
 	struct dma_slave_config	cfg;
 	struct sun6i_pchan	*phy;
 	u8			port;
+	u8			irq_type;
+	bool			cyclic;
 };
 
 struct sun6i_dma_dev {
@@ -254,6 +256,30 @@ static inline s8 convert_buswidth(enum dma_slave_buswidth addr_width)
 	return addr_width >> 1;
 }
 
+static size_t sun6i_get_chan_size(struct sun6i_pchan *pchan)
+{
+	struct sun6i_desc *txd = pchan->desc;
+	struct sun6i_dma_lli *lli;
+	size_t bytes;
+	dma_addr_t pos;
+
+	pos = readl(pchan->base + DMA_CHAN_LLI_ADDR);
+	bytes = readl(pchan->base + DMA_CHAN_CUR_CNT);
+
+	if (pos == LLI_LAST_ITEM)
+		return bytes;
+
+	for (lli = txd->v_lli; lli; lli = lli->v_lli_next) {
+		if (lli->p_lli_next == pos) {
+			for (lli = lli->v_lli_next; lli; lli = lli->v_lli_next)
+				bytes += lli->len;
+			break;
+		}
+	}
+
+	return bytes;
+}
+
 static void *sun6i_dma_lli_add(struct sun6i_dma_lli *prev,
 			       struct sun6i_dma_lli *next,
 			       dma_addr_t next_phy,
@@ -342,8 +368,12 @@ static int sun6i_dma_start_desc(struct sun6i_vchan *vchan)
 	irq_reg = pchan->idx / DMA_IRQ_CHAN_NR;
 	irq_offset = pchan->idx % DMA_IRQ_CHAN_NR;
 
+	vchan->irq_type = vchan->cyclic ? DMA_IRQ_PKG : DMA_IRQ_QUEUE;
+
 	irq_val = readl(sdev->base + DMA_IRQ_EN(irq_reg));
-	irq_val |= DMA_IRQ_QUEUE << (irq_offset * DMA_IRQ_CHAN_WIDTH);
+	irq_val &= ~((DMA_IRQ_HALF | DMA_IRQ_PKG | DMA_IRQ_QUEUE) <<
+			(irq_offset * DMA_IRQ_CHAN_WIDTH));
+	irq_val |= vchan->irq_type << (irq_offset * DMA_IRQ_CHAN_WIDTH);
 	writel(irq_val, sdev->base + DMA_IRQ_EN(irq_reg));
 
 	writel(pchan->desc->p_lli, pchan->base + DMA_CHAN_LLI_ADDR);
@@ -440,11 +470,12 @@ static irqreturn_t sun6i_dma_interrupt(int irq, void *dev_id)
 		writel(status, sdev->base + DMA_IRQ_STAT(i));
 
 		for (j = 0; (j < DMA_IRQ_CHAN_NR) && status; j++) {
-			if (status & DMA_IRQ_QUEUE) {
-				pchan = sdev->pchans + j;
-				vchan = pchan->vchan;
-
-				if (vchan) {
+			pchan = sdev->pchans + j;
+			vchan = pchan->vchan;
+			if (vchan && (status & vchan->irq_type)) {
+				if (vchan->cyclic) {
+					vchan_cyclic_callback(&pchan->desc->vd);
+				} else {
 					spin_lock(&vchan->vc.lock);
 					vchan_cookie_complete(&pchan->desc->vd);
 					pchan->done = pchan->desc;
@@ -650,6 +681,78 @@ err_lli_free:
 	return NULL;
 }
 
+static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_cyclic(
+					struct dma_chan *chan,
+					dma_addr_t buf_addr,
+					size_t buf_len,
+					size_t period_len,
+					enum dma_transfer_direction dir,
+					unsigned long flags)
+{
+	struct sun6i_dma_dev *sdev = to_sun6i_dma_dev(chan->device);
+	struct sun6i_vchan *vchan = to_sun6i_vchan(chan);
+	struct dma_slave_config *sconfig = &vchan->cfg;
+	struct sun6i_dma_lli *v_lli, *prev = NULL;
+	struct sun6i_desc *txd;
+	dma_addr_t p_lli;
+	u32 lli_cfg;
+	unsigned int i, periods = buf_len / period_len;
+	int ret;
+
+	ret = set_config(sdev, sconfig, dir, &lli_cfg);
+	if (ret) {
+		dev_err(chan2dev(chan), "Invalid DMA configuration\n");
+		return NULL;
+	}
+
+	txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
+	if (!txd)
+		return NULL;
+
+	for (i = 0; i < periods; i++) {
+		v_lli = dma_pool_alloc(sdev->pool, GFP_NOWAIT, &p_lli);
+		if (!v_lli) {
+			dev_err(sdev->slave.dev, "Failed to alloc lli memory\n");
+			goto err_lli_free;
+		}
+
+		v_lli->len = period_len;
+		v_lli->para = NORMAL_WAIT;
+
+		if (dir == DMA_MEM_TO_DEV) {
+			v_lli->src = buf_addr + period_len * i;
+			v_lli->dst = sconfig->dst_addr;
+			v_lli->cfg = lli_cfg |
+				DMA_CHAN_CFG_DST_IO_MODE |
+				DMA_CHAN_CFG_SRC_LINEAR_MODE |
+				DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
+				DMA_CHAN_CFG_DST_DRQ(vchan->port);
+		} else {
+			v_lli->src = sconfig->src_addr;
+			v_lli->dst = buf_addr + period_len * i;
+			v_lli->cfg = lli_cfg |
+				DMA_CHAN_CFG_DST_LINEAR_MODE |
+				DMA_CHAN_CFG_SRC_IO_MODE |
+				DMA_CHAN_CFG_DST_DRQ(DRQ_SDRAM) |
+				DMA_CHAN_CFG_SRC_DRQ(vchan->port);
+		}
+
+		prev = sun6i_dma_lli_add(prev, v_lli, p_lli, txd);
+	}
+
+	prev->p_lli_next = txd->p_lli;		/* cyclic list */
+
+	vchan->cyclic = true;
+
+	return vchan_tx_prep(&vchan->vc, &txd->vd, flags);
+
+err_lli_free:
+	for (prev = txd->v_lli; prev; prev = prev->v_lli_next)
+		dma_pool_free(sdev->pool, prev, virt_to_phys(prev));
+	kfree(txd);
+	return NULL;
+}
+
 static int sun6i_dma_config(struct dma_chan *chan,
 			    struct dma_slave_config *config)
 {
@@ -719,6 +822,16 @@ static int sun6i_dma_terminate_all(struct dma_chan *chan)
 
 	spin_lock_irqsave(&vchan->vc.lock, flags);
 
+	if (vchan->cyclic) {
+		vchan->cyclic = false;
+		if (pchan && pchan->desc) {
+			struct virt_dma_desc *vd = &pchan->desc->vd;
+			struct virt_dma_chan *vc = &vchan->vc;
+
+			list_add_tail(&vd->node, &vc->desc_completed);
+		}
+	}
+
 	vchan_get_all_descriptors(&vchan->vc, &head);
 
 	if (pchan) {
@@ -766,7 +879,7 @@ static enum dma_status sun6i_dma_tx_status(struct dma_chan *chan,
 	} else if (!pchan || !pchan->desc) {
 		bytes = 0;
 	} else {
-		bytes = readl(pchan->base + DMA_CHAN_CUR_CNT);
+		bytes = sun6i_get_chan_size(pchan);
 	}
 
 	spin_unlock_irqrestore(&vchan->vc.lock, flags);
@@ -970,6 +1083,7 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 	dma_cap_set(DMA_PRIVATE, sdc->slave.cap_mask);
 	dma_cap_set(DMA_MEMCPY, sdc->slave.cap_mask);
 	dma_cap_set(DMA_SLAVE, sdc->slave.cap_mask);
+	dma_cap_set(DMA_CYCLIC, sdc->slave.cap_mask);
 
 	INIT_LIST_HEAD(&sdc->slave.channels);
 	sdc->slave.device_free_chan_resources	= sun6i_dma_free_chan_resources;
@@ -977,6 +1091,7 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 	sdc->slave.device_issue_pending		= sun6i_dma_issue_pending;
 	sdc->slave.device_prep_slave_sg		= sun6i_dma_prep_slave_sg;
 	sdc->slave.device_prep_dma_memcpy	= sun6i_dma_prep_dma_memcpy;
+	sdc->slave.device_prep_dma_cyclic	= sun6i_dma_prep_dma_cyclic;
 	sdc->slave.copy_align			= DMAENGINE_ALIGN_4_BYTES;
 	sdc->slave.device_config		= sun6i_dma_config;
 	sdc->slave.device_pause			= sun6i_dma_pause;
Signature · 1 line
2.8.1
#6 lore raw

PATCH v5 3/3 dmaengine: sun6i: Add cyclic capability

Quoted 95 lines · Jean-Francois Moine

DMA cyclic transfers are required by audio streaming.

---
 drivers/dma/sun6i-dma.c | 129 +++++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 122 insertions(+), 7 deletions(-)
drivers/dma/sun6i-dma.c +44 -6
index 821fc4f..f0c4a53 100644
@@ -146,6 +146,8 @@ struct sun6i_vchan {
 	struct dma_slave_config	cfg;
 	struct sun6i_pchan	*phy;
 	u8			port;
+	u8			irq_type;
+	bool			cyclic;
 };
 
 struct sun6i_dma_dev {
@@ -254,6 +256,30 @@ static inline s8 convert_buswidth(enum dma_slave_buswidth addr_width)
 	return addr_width >> 1;
 }
 
+static size_t sun6i_get_chan_size(struct sun6i_pchan *pchan)
+{
+	struct sun6i_desc *txd = pchan->desc;
+	struct sun6i_dma_lli *lli;
+	size_t bytes;
+	dma_addr_t pos;
+
+	pos = readl(pchan->base + DMA_CHAN_LLI_ADDR);
+	bytes = readl(pchan->base + DMA_CHAN_CUR_CNT);
+
+	if (pos == LLI_LAST_ITEM)
+		return bytes;
+
+	for (lli = txd->v_lli; lli; lli = lli->v_lli_next) {
+		if (lli->p_lli_next == pos) {
+			for (lli = lli->v_lli_next; lli; lli = lli->v_lli_next)
+				bytes += lli->len;
+			break;
+		}
+	}
+
+	return bytes;
+}
+
 static void *sun6i_dma_lli_add(struct sun6i_dma_lli *prev,
 			       struct sun6i_dma_lli *next,
 			       dma_addr_t next_phy,
@@ -342,8 +368,12 @@ static int sun6i_dma_start_desc(struct sun6i_vchan *vchan)
 	irq_reg = pchan->idx / DMA_IRQ_CHAN_NR;
 	irq_offset = pchan->idx % DMA_IRQ_CHAN_NR;
 
+	vchan->irq_type = vchan->cyclic ? DMA_IRQ_PKG : DMA_IRQ_QUEUE;
+
 	irq_val = readl(sdev->base + DMA_IRQ_EN(irq_reg));
-	irq_val |= DMA_IRQ_QUEUE << (irq_offset * DMA_IRQ_CHAN_WIDTH);
+	irq_val &= ~((DMA_IRQ_HALF | DMA_IRQ_PKG | DMA_IRQ_QUEUE) <<
+			(irq_offset * DMA_IRQ_CHAN_WIDTH));
+	irq_val |= vchan->irq_type << (irq_offset * DMA_IRQ_CHAN_WIDTH);
 	writel(irq_val, sdev->base + DMA_IRQ_EN(irq_reg));
 
 	writel(pchan->desc->p_lli, pchan->base + DMA_CHAN_LLI_ADDR);
@@ -440,11 +470,12 @@ static irqreturn_t sun6i_dma_interrupt(int irq, void *dev_id)
 		writel(status, sdev->base + DMA_IRQ_STAT(i));
 
 		for (j = 0; (j < DMA_IRQ_CHAN_NR) && status; j++) {
-			if (status & DMA_IRQ_QUEUE) {
-				pchan = sdev->pchans + j;
-				vchan = pchan->vchan;
-
-				if (vchan) {
+			pchan = sdev->pchans + j;
+			vchan = pchan->vchan;
+			if (vchan && (status & vchan->irq_type)) {
+				if (vchan->cyclic) {
+					vchan_cyclic_callback(&pchan->desc->vd);
+				} else {
 					spin_lock(&vchan->vc.lock);
 					vchan_cookie_complete(&pchan->desc->vd);
 					pchan->done = pchan->desc;
@@ -650,6 +681,78 @@ err_lli_free:
 	return NULL;
 }
 
+static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_cyclic(
+					struct dma_chan *chan,
+					dma_addr_t buf_addr,
+					size_t buf_len,
+					size_t period_len,
+					enum dma_transfer_direction dir,
+					unsigned long flags)

drivers/dma/sun6i-dma.c err_lli_free: · line 700

Quoted 10 lines
drivers/dma/sun6i-dma.c +10 -0
+{
+	struct sun6i_dma_dev *sdev = to_sun6i_dma_dev(chan->device);
+	struct sun6i_vchan *vchan = to_sun6i_vchan(chan);
+	struct dma_slave_config *sconfig = &vchan->cfg;
+	struct sun6i_dma_lli *v_lli, *prev = NULL;
+	struct sun6i_desc *txd;
+	dma_addr_t p_lli;
+	u32 lli_cfg;
+	unsigned int i, periods = buf_len / period_len;
+	int ret;

typically we check if direction is slave or not..

Quoted 20 lines
drivers/dma/sun6i-dma.c +20 -0
+
+	ret = set_config(sdev, sconfig, dir, &lli_cfg);
+	if (ret) {
+		dev_err(chan2dev(chan), "Invalid DMA configuration\n");
+		return NULL;
+	}
+
+	txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
+	if (!txd)
+		return NULL;
+
+	for (i = 0; i < periods; i++) {
+		v_lli = dma_pool_alloc(sdev->pool, GFP_NOWAIT, &p_lli);
+		if (!v_lli) {
+			dev_err(sdev->slave.dev, "Failed to alloc lli memory\n");
+			goto err_lli_free;
+		}
+
+		v_lli->len = period_len;
+		v_lli->para = NORMAL_WAIT;

drivers/dma/sun6i-dma.c err_lli_free: · line 730

Quoted 10 lines
drivers/dma/sun6i-dma.c +10 -0
+
+		if (dir == DMA_MEM_TO_DEV) {
+			v_lli->src = buf_addr + period_len * i;
+			v_lli->dst = sconfig->dst_addr;
+			v_lli->cfg = lli_cfg |
+				DMA_CHAN_CFG_DST_IO_MODE |
+				DMA_CHAN_CFG_SRC_LINEAR_MODE |
+				DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
+				DMA_CHAN_CFG_DST_DRQ(vchan->port);
+		} else {

if we check direction above, then this is fine

Signature · 1 line
~Vinod