Skip to contentSkip to conversation

raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

PATCH Superseded Peter Seiderer 5 participants 12 messages May 2, 2016 – Sep 19, 2016 Broadcom BCM2711/BCM2835 Arm architecture

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig

---
Changes v1 --> v2:
- use pi3-miniuart-bt instead of pi3-disable-bt
- fix post-image.sh to add overlay lines only once
- add overlay description (and alternative solution) to readme.txt

---
 board/raspberrypi/genimage-raspberrypi3.cfg |  1 +
 board/raspberrypi/post-image.sh             | 13 +++++++++++++
 board/raspberrypi/readme.txt                |  8 +++++++-
 configs/raspberrypi3_defconfig              |  3 ++-
 4 files changed, 23 insertions(+), 2 deletions(-)
board/raspberrypi/genimage-raspberrypi3.cfg +1 -0
index 7ba89c5..baab0c4 100644
@@ -7,6 +7,7 @@ image boot.vfat {
       "rpi-firmware/config.txt",
       "rpi-firmware/fixup.dat",
       "rpi-firmware/start.elf",
+      "rpi-firmware/overlays",
       "kernel-marked/zImage"
     }
   }
board/raspberrypi/post-image.sh +13 -0
index 73ffd65..c009752 100755
@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"
 GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
+case "${2}" in
+	--add-pi3-miniuart-bt-overlay)
+	if ! grep -qE '^dtoverlay=' "${BINARIES_DIR}/rpi-firmware/config.txt"; then
+		echo "Adding 'dtoverlay=pi3-miniuart-bt' to config.txt (fixes ttyAMA0 serial console)."
+		cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt"
+
+# fixes rpi3 ttyAMA0 serial console
+dtoverlay=pi3-miniuart-bt
+__EOF__
+	fi
+	;;
+esac
+
 # Mark the kernel as DT-enabled
 mkdir -p "${BINARIES_DIR}/kernel-marked"
 ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \
board/raspberrypi/readme.txt +7 -1
index a170f8f..03178ff 100644
@@ -60,7 +60,8 @@ After building, you should obtain this tree:
     |   +-- cmdline.txt
     |   +-- config.txt
     |   +-- fixup.dat
-    |   `-- start.elf
+    |   +-- start.elf
+    |   `-- overlays/               [3]
     +-- sdcard.img
     `-- zImage
 
@@ -69,6 +70,11 @@ After building, you should obtain this tree:
 
 [2] This is the mkknlimg DT-marked kernel.
 
+[3] Only for the Raspberry Pi 3 Model (overlay pi3-miniuart-bt is needed
+    to enable the RPi3 serial console otherwise occupied by the bluetooth
+    chip). Alternative would be to disable the serial console in cmdline.txt
+    and /etc/inittab.
+
 How to write the SD card
 ========================
 
configs/raspberrypi3_defconfig +2 -1
index 4eb5333..8600cd8 100644
@@ -21,7 +21,7 @@ BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="bcm2710-rpi-3-b"
 
 BR2_PACKAGE_RPI_FIRMWARE=y
-# BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS is not set
+BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
 
 # Required tools to create the SD image
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh"
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay"
Signature · 1 line
2.8.1
#1 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hi Peter Seiderer,

What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

Best regards.

Oscar Gomez Fuente.

Quoted 109 lines · Peter Seiderer

- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig

---
Changes v1 --> v2:
- use pi3-miniuart-bt instead of pi3-disable-bt
- fix post-image.sh to add overlay lines only once
- add overlay description (and alternative solution) to readme.txt

---
 board/raspberrypi/genimage-raspberrypi3.cfg |  1 +
 board/raspberrypi/post-image.sh             | 13 +++++++++++++
 board/raspberrypi/readme.txt                |  8 +++++++-
 configs/raspberrypi3_defconfig              |  3 ++-
 4 files changed, 23 insertions(+), 2 deletions(-)
board/raspberrypi/genimage-raspberrypi3.cfg +1 -0
index 7ba89c5..baab0c4 100644
@@ -7,6 +7,7 @@ image boot.vfat {
       "rpi-firmware/config.txt",
       "rpi-firmware/fixup.dat",
       "rpi-firmware/start.elf",
+      "rpi-firmware/overlays",
       "kernel-marked/zImage"
     }
   }
board/raspberrypi/post-image.sh +3 -0
index 73ffd65..c009752 100755
@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"
 GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg"
 GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
+case "${2}" in
+       --add-pi3-miniuart-bt-overlay)
+       if ! grep -qE '^dtoverlay='

"${BINARIES_DIR}/rpi-firmware/config.txt"; then
+ echo "Adding 'dtoverlay=pi3-miniuart-bt' to config.txt
(fixes ttyAMA0 serial console)."

board/raspberrypi/post-image.sh +9 -0
+               cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt"
+
+# fixes rpi3 ttyAMA0 serial console
+dtoverlay=pi3-miniuart-bt
+__EOF__
+       fi
+       ;;
+esac
+
 # Mark the kernel as DT-enabled
 mkdir -p "${BINARIES_DIR}/kernel-marked"
 ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \
board/raspberrypi/readme.txt +5 -1
index a170f8f..03178ff 100644
@@ -60,7 +60,8 @@ After building, you should obtain this tree:
     |   +-- cmdline.txt
     |   +-- config.txt
     |   +-- fixup.dat
-    |   `-- start.elf
+    |   +-- start.elf
+    |   `-- overlays/               [3]
     +-- sdcard.img
     `-- zImage
 
@@ -69,6 +70,11 @@ After building, you should obtain this tree:
 
 [2] This is the mkknlimg DT-marked kernel.
 
+[3] Only for the Raspberry Pi 3 Model (overlay pi3-miniuart-bt is needed
+    to enable the RPi3 serial console otherwise occupied by the bluetooth
+    chip). Alternative would be to disable the serial console in

cmdline.txt

board/raspberrypi/readme.txt +2 -0
+    and /etc/inittab.
+
 How to write the SD card
 ========================
configs/raspberrypi3_defconfig +2 -2
index 4eb5333..8600cd8 100644
@@ -21,7 +21,7 @@ BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="bcm2710-rpi-3-b"
 
 BR2_PACKAGE_RPI_FIRMWARE=y
-# BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS is not set
+BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
 
 # Required tools to create the SD image
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh"
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay"
--
Quoted 3 lines

2.8.1

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160503/1ca24628/attachment.html>

#2 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Oscar" == Oscar Gomez Fuente <[email protected]> writes:

Hi Peter Seiderer,
What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

From the names I would guess it is the difference between completely disabling access to the bluetooth module and providing access to it though the secondary (mini) uart.

The miniuart has some limitations, but I guess basic bluetooth stuff should work with it.

Signature · 2 lines
Venlig hilsen,
Peter Korsgaard 
#3 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

All,

Quoted 9 lines · Peter Korsgaard
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Oscar" == Oscar Gomez Fuente <[email protected]> writes:

Hi Peter Seiderer,
What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

Quoted 6 lines

From the names I would guess it is the difference between completely disabling access to the bluetooth module and providing access to it though the secondary (mini) uart.

The miniuart has some limitations, but I guess basic bluetooth stuff should work with it.

I've got a bit lost in the rpi3 serial console issues but as i understand the current situation all you need to do is set enable_uart=1 in config.txt. See
https://github.com/raspberrypi/firmware/issues/553#issuecomment-199486644.
I've not tested this.

I think you also need to change cmdline.txt to use console=serial0 as
the pi3-miniuart-bt will replace it with the correct serial device
(ttyAMA0 or ttyS0) depending if it's enabled or not. See the comments
in https://github.com/raspberrypi/linux/blob/rpi-4.1.y/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts.

Thanks

Martin

Quoted 8 lines

--
Venlig hilsen,
Peter Korsgaard
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

#4 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hello Martin,

Quoted 25 lines · Martin Bark

All,

Quoted 9 lines · Peter Korsgaard
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Oscar" == Oscar Gomez Fuente <[email protected]> writes:

Hi Peter Seiderer,
What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

Quoted 6 lines

From the names I would guess it is the difference between completely disabling access to the bluetooth module and providing access to it though the secondary (mini) uart.

The miniuart has some limitations, but I guess basic bluetooth stuff should work with it.

I've got a bit lost in the rpi3 serial console issues but as i understand the current situation all you need to do is set enable_uart=1 in config.txt. See
https://github.com/raspberrypi/firmware/issues/553#issuecomment-199486644.
I've not tested this.

Quoted 5 lines

I think you also need to change cmdline.txt to use console=serial0 as
the pi3-miniuart-bt will replace it with the correct serial device
(ttyAMA0 or ttyS0) depending if it's enabled or not. See the comments
in https://github.com/raspberrypi/linux/blob/rpi-4.1.y/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts.

This works too, not sure whats the better solution, explicit via device tree overlay or some firmware magic....

- pi3-miniuart-bt 'dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200
[    0.001320] console [tty1] enabled
[    0.318181] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 50000000) is a 16550
[    2.008162] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    3.296233] console [ttyAMA0] enabled

- enable-uart=1, serial0 dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyS0,115200
[    0.001318] console [tty1] enabled
[    0.318270] console [ttyS0] disabled
[    0.318389] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 31250000) is a 16550
[    1.042714] console [ttyS0] enabled
[    3.020277] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2

Regards,
Peter

Quoted 12 lines

Thanks

Martin

Quoted 8 lines

--
Venlig hilsen,
Peter Korsgaard
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

#5 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Peter,

Quoted 45 lines · Peter Seiderer

Hello Martin,

Quoted 25 lines · Martin Bark

All,

Quoted 9 lines · Peter Korsgaard
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Oscar" == Oscar Gomez Fuente <[email protected]> writes:

Hi Peter Seiderer,
What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

Quoted 6 lines

From the names I would guess it is the difference between completely disabling access to the bluetooth module and providing access to it though the secondary (mini) uart.

The miniuart has some limitations, but I guess basic bluetooth stuff should work with it.

I've got a bit lost in the rpi3 serial console issues but as i understand the current situation all you need to do is set enable_uart=1 in config.txt. See
https://github.com/raspberrypi/firmware/issues/553#issuecomment-199486644.
I've not tested this.

Quoted 5 lines

I think you also need to change cmdline.txt to use console=serial0 as
the pi3-miniuart-bt will replace it with the correct serial device
(ttyAMA0 or ttyS0) depending if it's enabled or not. See the comments
in https://github.com/raspberrypi/linux/blob/rpi-4.1.y/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts.

This works too, not sure whats the better solution, explicit via device tree overlay or some firmware magic....

- pi3-miniuart-bt 'dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200
[    0.001320] console [tty1] enabled
[    0.318181] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 50000000) is a 16550
[    2.008162] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    3.296233] console [ttyAMA0] enabled
Quoted 8 lines

- enable-uart=1, serial0 dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyS0,115200
[    0.001318] console [tty1] enabled
[    0.318270] console [ttyS0] disabled
[    0.318389] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 31250000) is a 16550
[    1.042714] console [ttyS0] enabled
[    3.020277] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2

I wonder if the solution is to just document the situation in board/raspberrypi/readme.txt. The documentation could just detail the available choices for Bluetooth and serial console on the rpi3 and how to configure each manually. A summary of the available choices is:

1) Default setup - Serial console does not work, Bluetooth works
2) Add enable-uart=1 - Serial console works but the core frequency is fixed. Serial console max baud rate is less than the rpi2. Bluetooth works.
3) Use pi3-miniuart-bt - Serial console works the same as the rpi2 but Bluetooth runs slow.
4) Use pi3-disable-bt - Serial console works the same as the rpi2 but Bluetooth is disabled.

What do you think?

Thanks

Martin

Quoted 17 lines

Regards,
Peter

Quoted 12 lines

Thanks

Martin

Quoted 8 lines

--
Venlig hilsen,
Peter Korsgaard
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

#6 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hello Martin,

Quoted 71 lines · Martin Bark

Peter,

Quoted 45 lines · Peter Seiderer

Hello Martin,

Quoted 25 lines · Martin Bark

All,

Quoted 9 lines · Peter Korsgaard
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Oscar" == Oscar Gomez Fuente <[email protected]> writes:

Hi Peter Seiderer,
What's the difference between enabling pi3-miniuart-bt instead of pi3-disable-bt?

With pi3-disable-bt enables it works fine the serial console on (14 [TxD] & 15 [RxD] pins).

Quoted 6 lines

From the names I would guess it is the difference between completely disabling access to the bluetooth module and providing access to it though the secondary (mini) uart.

The miniuart has some limitations, but I guess basic bluetooth stuff should work with it.

I've got a bit lost in the rpi3 serial console issues but as i understand the current situation all you need to do is set enable_uart=1 in config.txt. See
https://github.com/raspberrypi/firmware/issues/553#issuecomment-199486644.
I've not tested this.

Quoted 5 lines

I think you also need to change cmdline.txt to use console=serial0 as
the pi3-miniuart-bt will replace it with the correct serial device
(ttyAMA0 or ttyS0) depending if it's enabled or not. See the comments
in https://github.com/raspberrypi/linux/blob/rpi-4.1.y/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts.

This works too, not sure whats the better solution, explicit via device tree overlay or some firmware magic....

- pi3-miniuart-bt 'dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200
[    0.001320] console [tty1] enabled
[    0.318181] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 50000000) is a 16550
[    2.008162] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    3.296233] console [ttyAMA0] enabled
Quoted 8 lines

- enable-uart=1, serial0 dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyS0,115200
[    0.001318] console [tty1] enabled
[    0.318270] console [ttyS0] disabled
[    0.318389] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 31250000) is a 16550
[    1.042714] console [ttyS0] enabled
[    3.020277] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2

I wonder if the solution is to just document the situation in board/raspberrypi/readme.txt. The documentation could just detail the available choices for Bluetooth and serial console on the rpi3 and how to configure each manually. A summary of the available choices is:

1) Default setup - Serial console does not work, Bluetooth works
2) Add enable-uart=1 - Serial console works but the core frequency is fixed. Serial console max baud rate is less than the rpi2. Bluetooth works.
3) Use pi3-miniuart-bt - Serial console works the same as the rpi2 but Bluetooth runs slow.
4) Use pi3-disable-bt - Serial console works the same as the rpi2 but Bluetooth is disabled.

Quoted 1 line

What do you think?

Agreed, with bias to 3) as the default (or one of the other solutions with serial console enabled)...

Regards,
Peter

Quoted 22 lines

Thanks

Martin

Quoted 17 lines

Regards,
Peter

Quoted 12 lines

Thanks

Martin

Quoted 8 lines

--
Venlig hilsen,
Peter Korsgaard
_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

#7 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hello,

Quoted 14 lines · Peter Seiderer
Quoted 14 lines

I wonder if the solution is to just document the situation in board/raspberrypi/readme.txt. The documentation could just detail the available choices for Bluetooth and serial console on the rpi3 and how to configure each manually. A summary of the available choices is:

1) Default setup - Serial console does not work, Bluetooth works
2) Add enable-uart=1 - Serial console works but the core frequency is fixed. Serial console max baud rate is less than the rpi2. Bluetooth works.
3) Use pi3-miniuart-bt - Serial console works the same as the rpi2 but Bluetooth runs slow.
4) Use pi3-disable-bt - Serial console works the same as the rpi2 but Bluetooth is disabled.

Quoted 4 lines
Quoted 1 line

What do you think?

Agreed, with bias to 3) as the default (or one of the other solutions with serial console enabled)...

Yes, sounds like a good idea.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#8 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

In reply to Peter Seiderer

Hello,

Quoted 10 lines · Peter Seiderer

This works too, not sure whats the better solution, explicit via device tree overlay or some firmware magic....

- pi3-miniuart-bt 'dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200
[    0.001320] console [tty1] enabled
[    0.318181] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 50000000) is a 16550
[    2.008162] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    3.296233] console [ttyAMA0] enabled
Quoted 7 lines

- enable-uart=1, serial0 dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyS0,115200
[    0.001318] console [tty1] enabled
[    0.318270] console [ttyS0] disabled
[    0.318389] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 31250000) is a 16550
[    1.042714] console [ttyS0] enabled
[    3.020277] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2

For the Buildroot defconfig, I believe passing enable-uart=1 in config.txt would be the easiest solution. Could you send a patch that does this instead of messing with the overlays ?

Thanks!

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#9 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hello Thomas,

Quoted 22 lines · Thomas Petazzoni

Hello,

Quoted 10 lines · Peter Seiderer

This works too, not sure whats the better solution, explicit via device tree overlay or some firmware magic....

- pi3-miniuart-bt 'dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyAMA0,115200
[    0.001320] console [tty1] enabled
[    0.318181] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 50000000) is a 16550
[    2.008162] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    3.296233] console [ttyAMA0] enabled
Quoted 7 lines

- enable-uart=1, serial0 dmesg | grep tty':

[    0.000000] Kernel command line: 8250.nr_uarts=1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1200 bcm2709.boardrev=0xa02082 bcm2709.serial=0xa60340 smsc95xx.macaddr=B8:27:EB:A6:03:40 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  root=/dev/mmcblk0p2 rootwait console=tty1 console=ttyS0,115200
[    0.001318] console [tty1] enabled
[    0.318270] console [ttyS0] disabled
[    0.318389] 3f215040.uart: ttyS0 at MMIO 0x3f215040 (irq = 59, base_baud = 31250000) is a 16550
[    1.042714] console [ttyS0] enabled
[    3.020277] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
Quoted 3 lines

For the Buildroot defconfig, I believe passing enable-uart=1 in config.txt would be the easiest solution. Could you send a patch that does this instead of messing with the overlays ?

Sorry for the delay, I tried the 'enable-uart=1' solution some time ago and it did not work (I think I messed something up), retried today and it worked, patch will follow...

Regards,
Peter

Quoted 4 lines

Thanks!

Thomas

#10 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

In reply to Peter Seiderer

Hello,

Quoted 11 lines · Peter Seiderer

- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig

---
Changes v1 --> v2:
- use pi3-miniuart-bt instead of pi3-disable-bt
- fix post-image.sh to add overlay lines only once
- add overlay description (and alternative solution) to readme.txt

Quoted 6 lines
---
 board/raspberrypi/genimage-raspberrypi3.cfg |  1 +
 board/raspberrypi/post-image.sh             | 13 +++++++++++++
 board/raspberrypi/readme.txt                |  8 +++++++-
 configs/raspberrypi3_defconfig              |  3 ++-
 4 files changed, 23 insertions(+), 2 deletions(-)

What I understood from the discussions on your new patch "raspberrypi3:
fix serial console (add enable_uart=1", this older proposal is actually what is preferred. It is a bit more complicated than just passing enable_uart=1, but it allows to have the UART *and* run the CPU as its normal frequency.

So, I've applied this patch, and marked the newer one (enable_uart=1) as rejected.

It would be good if you could rebuild the raspberrypi3_defconfig, and check that it works for you. While you're at it, it would be useful if you could look at the bug report
https://bugs.busybox.net/show_bug.cgi?id=9196 and see if you can reproduce the issue and/or help solve the problem.

Thanks a lot for your contribution!

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#11 lore raw

PATCH v2 1/1 raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

Hello Thomas,

Quoted 27 lines · Thomas Petazzoni

Hello,

Quoted 11 lines · Peter Seiderer

- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig

---
Changes v1 --> v2:
- use pi3-miniuart-bt instead of pi3-disable-bt
- fix post-image.sh to add overlay lines only once
- add overlay description (and alternative solution) to readme.txt

Quoted 6 lines
---
 board/raspberrypi/genimage-raspberrypi3.cfg |  1 +
 board/raspberrypi/post-image.sh             | 13 +++++++++++++
 board/raspberrypi/readme.txt                |  8 +++++++-
 configs/raspberrypi3_defconfig              |  3 ++-
 4 files changed, 23 insertions(+), 2 deletions(-)

What I understood from the discussions on your new patch "raspberrypi3:
fix serial console (add enable_uart=1", this older proposal is actually what is preferred. It is a bit more complicated than just passing enable_uart=1, but it allows to have the UART *and* run the CPU as its normal frequency.

Quoted 5 lines

So, I've applied this patch, and marked the newer one (enable_uart=1) as rejected.

It would be good if you could rebuild the raspberrypi3_defconfig, and check that it works for you. While you're at it, it would be useful if

Still works as expected for me, tested with buildroot git d4db4277ffbd1fae478ba748c626eddc7c220e67, login via serial and login via hdmi/usb-keyboard possible...

Quoted 3 lines

you could look at the bug report
https://bugs.busybox.net/show_bug.cgi?id=9196 and see if you can reproduce the issue and/or help solve the problem.

Will check the systemd case tomorrow...

Regards,
Peter

Quoted 4 lines

Thanks a lot for your contribution!

Thomas