ARM: clps711x: Switch to DT and Multiplatform

index abe2254..c17ac5c 100644
@@ -9,10 +9,10 @@
 
 #ifndef CONFIG_DEBUG_CLPS711X_UART2
 #define CLPS711X_UART_PADDR	(0x80000000 + 0x0000)
-#define CLPS711X_UART_VADDR	(0xfeff0000 + 0x0000)
+#define CLPS711X_UART_VADDR	(0xfeff4000 + 0x0000)
 #else
 #define CLPS711X_UART_PADDR	(0x80000000 + 0x1000)
-#define CLPS711X_UART_VADDR	(0xfeff0000 + 0x1000)
+#define CLPS711X_UART_VADDR	(0xfeff4000 + 0x1000)
 #endif
 
 #define SYSFLG		(0x0140)

index ce5a747..f1bd53f 100644
@@ -1,7 +1,7 @@
 * Clock bindings for the Cirrus Logic CLPS711X CPUs
 
 Required properties:
-- compatible       : Shall contain "cirrus,clps711x-clk".
+- compatible       : Shall contain "cirrus,ep7209-clk".
 - reg              : Address of the internal register set.
 - startup-frequency: Factory set CPU startup frequency in HZ.
 - #clock-cells     : Should be <1>.

@@ -13,7 +13,7 @@ for the full list of CLPS711X clock IDs.
 Example:
 	clks: clks at 80000000 {
 		#clock-cells = <1>;
-		compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk";
+		compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk";
 		reg = <0x80000000 0xc000>;
 		startup-frequency = <73728000>;
 	};

index cd55b52..d4c62e7 100644
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X Timer Counter
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-timer".
+- compatible: Shall contain "cirrus,ep7209-timer".
 - reg       : Address and length of the register set.
 - interrupts: The interrupt number of the timer.
 - clocks    : phandle of timer reference clock.

@@ -15,14 +15,14 @@ Example:
 	};
 
 	timer1: timer at 80000300 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000300 0x4>;
 		interrupts = <8>;
 		clocks = <&clks 5>;
 	};
 
 	timer2: timer at 80000340 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000340 0x4>;
 		interrupts = <9>;
 		clocks = <&clks 6>;

index 759339c..969b458 100644
@@ -2,7 +2,7 @@ Cirrus Logic CLPS711X Interrupt Controller
 
 Required properties:
 
-- compatible: Should be "cirrus,clps711x-intc".
+- compatible: Should be "cirrus,ep7209-intc".
 - reg: Specifies base physical address of the registers set.
 - interrupt-controller: Identifies the node as an interrupt controller.
 - #interrupt-cells: Specifies the number of cells needed to encode an

@@ -34,7 +34,7 @@ ID	Name	Description
 
 Example:
 	intc: interrupt-controller {
-		compatible = "cirrus,clps711x-intc";
+		compatible = "cirrus,ep7312-intc", "cirrus,ep7209-intc";
 		reg = <0x80000000 0x4000>;
 		interrupt-controller;
 		#interrupt-cells = <1>;

index caaeb25..07013fa 100644
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART)
 
 Required properties:
-- compatible: Should be "cirrus,clps711x-uart".
+- compatible: Should be "cirrus,ep7209-uart".
 - reg: Address and length of the register set for the device.
 - interrupts: Should contain UART TX and RX interrupt.
 - clocks: Should contain UART core clock number.

@@ -20,7 +20,7 @@ Example:
 	};
 
 	uart1: uart at 80000480 {
-		compatible = "cirrus,clps711x-uart";
+		compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart";
 		reg = <0x80000480 0x80>;
 		interrupts = <12 13>;
 		clocks = <&clks 11>;

index a183db4..c0b2028 100644
@@ -1,15 +1,14 @@
 * Cirris Logic CLPS711X PWM controller
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-pwm".
+- compatible: Shall contain "cirrus,ep7209-pwm".
 - reg: Physical base address and length of the controller's registers.
 - clocks: phandle + clock specifier pair of the PWM reference clock.
 - #pwm-cells: Should be 1. The cell specifies the index of the channel.
 
 Example:
 	pwm: pwm at 80000400 {
-		compatible = "cirrus,ep7312-pwm",
-			     "cirrus,clps711x-pwm";
+		compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm";
 		reg = <0x80000400 0x4>;
 		clocks = <&clks 8>;
 		#pwm-cells = <1>;

index e0d0446..0a304ad 100644
@@ -1,7 +1,7 @@
 Cirrus Logic CLPS711X GPIO controller
 
 Required properties:
-- compatible: Should be "cirrus,clps711x-gpio"
+- compatible: Should be "cirrus,ep7209-gpio"
 - reg: Physical base GPIO controller registers location and length.
   There should be two registers, first is DATA register, the second
   is DIRECTION.

@@ -21,7 +21,7 @@ aliases {
 };
 
 porta: gpio at 80000000 {
-	compatible = "cirrus,clps711x-gpio";
+	compatible = "cirrus,ep7312-gpio","cirrus,ep7209-gpio";
 	reg = <0x80000000 0x1>, <0x80000040 0x1>;
 	gpio-controller;
 	#gpio-cells = <2>;

index 94ae9f8..fd42e72 100644
@@ -1,7 +1,7 @@
 * ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs
 
 Required properties:
-- compatible: Should contain "cirrus,clps711x-mctrl-gpio".
+- compatible: Should contain "cirrus,ep7209-mctrl-gpio".
 - gpio-controller: Marks the device node as a gpio controller.
 - #gpio-cells: Should be two. The first cell is the pin number and
   the second cell is used to specify the gpio polarity:

@@ -11,7 +11,7 @@ Required properties:
 Example:
 	sysgpio: sysgpio {
 		compatible = "cirrus,ep7312-mctrl-gpio",
-			     "cirrus,clps711x-mctrl-gpio";
+			     "cirrus,ep7209-mctrl-gpio";
 		gpio-controller;
 		#gpio-cells = <2>;
 	};

index e68d2bb..3eed881 100644
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X matrix keypad device tree bindings
 
 Required Properties:
-- compatible:    Shall contain "cirrus,clps711x-keypad".
+- compatible:    Shall contain "cirrus,ep7209-keypad".
 - row-gpios:     List of GPIOs used as row lines.
 - poll-interval: Poll interval time in milliseconds.
 - linux,keymap:  The definition can be found at

@@ -12,7 +12,7 @@ Optional Properties:
 
 Example:
 	keypad {
-		compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad";
+		compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad";
 		autorepeat;
 		poll-interval = <120>;
 		row-gpios = <&porta 0 0>,

index d685be8..e9c6574 100644
@@ -1,7 +1,7 @@
 * Currus Logic CLPS711X Framebuffer
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-fb".
+- compatible: Shall contain "cirrus,ep7209-fb".
 - reg       : Physical base address and length of the controller's registers +
               location and size of the framebuffer memory.
 - clocks    : phandle + clock specifier pair of the FB reference clock.

@@ -18,7 +18,7 @@ Optional properties:
 
 Example:
 	fb: fb at 800002c0 {
-		compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb";
+		compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb";
 		reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 		clocks = <&clks 2>;
 		lcd-supply = <&reg5v0>;

index f711498..f21700c 100644
@@ -2,6 +2,15 @@ if ARCH_CLPS711X
 
 menu "CLPS711X/EP721X/EP731X Implementations"
 
+config MACH_CLPS711X_DT
+	bool "Device-tree support"
+	select CLKSRC_OF
+	select OF_IRQ
+	select USE_OF
+	help
+	  Select this if you want to experiment device-tree with
+	  ARMv4T Cirrus Logic chips.
+
 config ARCH_AUTCPU12
 	bool "AUTCPU12"
 	help

index f04151e..ef6df40 100644
@@ -6,6 +6,7 @@
 
 obj-y				:= common.o devices.o
 
+obj-$(CONFIG_MACH_CLPS711X_DT)	+= board-dt.o
 obj-$(CONFIG_ARCH_AUTCPU12)	+= board-autcpu12.o
 obj-$(CONFIG_ARCH_CDB89712)	+= board-cdb89712.o
 obj-$(CONFIG_ARCH_CLEP7312)	+= board-clep7312.o

index 06b6c2d..e409890 100644
@@ -104,6 +104,8 @@ dtb-$(CONFIG_ARCH_BERLIN) += \
 	berlin2q-marvell-dmp.dtb
 dtb-$(CONFIG_ARCH_BRCMSTB) += \
 	bcm7445-bcm97445svmb.dtb
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += \
 	da850-enbw-cmc.dtb \
 	da850-evm.dtb

191 lines not on this page · raw message

100 lines not on this page · raw message

new file mode 100644
index 0000000..e438f6d
@@ -0,0 +1,12 @@
+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ */
+
+#include "ep7209.dtsi"
+
+/ {
+	model = "Cirrus Logic EP7211";
+	compatible = "cirrus,ep7211", "cirrus,ep7209";
+};

deleted file mode 100644
index fc105c9..0000000
@@ -1,91 +0,0 @@
-CONFIG_KERNEL_LZMA=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_RD_LZMA=y
-CONFIG_EMBEDDED=y
-CONFIG_SLOB=y
-CONFIG_JUMP_LABEL=y
-# CONFIG_LBDAF is not set
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_CLPS711X=y
-CONFIG_ARCH_AUTCPU12=y
-CONFIG_ARCH_CDB89712=y
-CONFIG_ARCH_CLEP7312=y
-CONFIG_ARCH_EDB7211=y
-CONFIG_ARCH_P720T=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-# CONFIG_COREDUMP is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_IRTTY_SIR=y
-# CONFIG_WIRELESS is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_PLATRAM=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_GPIO=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_CADENCE is not set
-# CONFIG_NET_VENDOR_BROADCOM is not set
-CONFIG_CS89x0=y
-CONFIG_CS89x0_PLATFORM=y
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_NET_VENDOR_WIZNET is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_CLPS711X=y
-CONFIG_SERIAL_CLPS711X_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_CLPS711X=y
-CONFIG_GPIO_CLPS711X=y
-CONFIG_GPIO_GENERIC_PLATFORM=y
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-CONFIG_FB_CLPS711X=y
-CONFIG_LCD_PLATFORM=y
-CONFIG_BACKLIGHT_PWM=y
-# CONFIG_USB_SUPPORT is not set
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-# CONFIG_IOMMU_SUPPORT is not set
-CONFIG_PWM=y
-CONFIG_PWM_CLPS711X=y
-CONFIG_EXT2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_MINIX_FS=y
-# CONFIG_NETWORK_FILESYSTEMS is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_EARLY_PRINTK=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set

index f21700c..0a170e1 100644
@@ -11,37 +11,6 @@ config MACH_CLPS711X_DT
 	  Select this if you want to experiment device-tree with
 	  ARMv4T Cirrus Logic chips.
 
-config ARCH_AUTCPU12
-	bool "AUTCPU12"
-	help
-	  Say Y if you intend to run the kernel on the autronix autcpu12
-	  board. This board is based on a Cirrus Logic CS89712.
-
-config ARCH_CDB89712
-	bool "CDB89712"
-	help
-	  This is an evaluation board from Cirrus for the CS89712 processor.
-	  The board includes 2 serial ports, Ethernet, IRDA, and expansion
-	  headers.  It comes with 16 MB SDRAM and 8 MB flash ROM.
-
-config ARCH_CLEP7312
-	bool "CLEP7312"
-	help
-	  Boards based on the Cirrus Logic 7212/7312 chips.
-
-config ARCH_EDB7211
-	bool "EDB7211"
-	select ARCH_HAS_HOLES_MEMORYMODEL
-	help
-	  Say Y here if you intend to run this kernel on a Cirrus Logic EDB-7211
-	  evaluation board.
-
-config ARCH_P720T
-	bool "P720T"
-	help
-	  Say Y here if you intend to run this kernel on the ARM Prospector
-	  720T.
-
 endmenu
 
 endif

index ef6df40..d79d998 100644
@@ -1,14 +1 @@
-#
-# Makefile for the linux kernel.
-#
-
-# Object file lists.
-
-obj-y				:= common.o devices.o
-
 obj-$(CONFIG_MACH_CLPS711X_DT)	+= board-dt.o
-obj-$(CONFIG_ARCH_AUTCPU12)	+= board-autcpu12.o
-obj-$(CONFIG_ARCH_CDB89712)	+= board-cdb89712.o
-obj-$(CONFIG_ARCH_CLEP7312)	+= board-clep7312.o
-obj-$(CONFIG_ARCH_EDB7211)	+= board-edb7211.o
-obj-$(CONFIG_ARCH_P720T)	+= board-p720t.o

index eba77d3..e69de29 100644
@@ -1,5 +0,0 @@
-# The standard locations for stuff on CLPS711x type processors
-params_phys-y				:= 0xc0000100
-# Should probably have some agreement on these...
-initrd_phys-$(CONFIG_ARCH_P720T)	:= 0xc0400000
-initrd_phys-$(CONFIG_ARCH_CDB89712)	:= 0x00700000

index 88b008f..e050f18 100644
@@ -317,16 +317,9 @@ config FB_ACORN
 	  hardware found in Acorn RISC PCs and other ARM-based machines.  If
 	  unsure, say N.
 
-config FB_CLPS711X_OLD
-	tristate
-	select FB_CFB_FILLRECT
-	select FB_CFB_COPYAREA
-	select FB_CFB_IMAGEBLIT
-
 config FB_CLPS711X
 	tristate "CLPS711X LCD support"
 	depends on FB && (ARCH_CLPS711X || COMPILE_TEST)
-	select FB_CLPS711X_OLD if ARCH_CLPS711X && !ARCH_MULTIPLATFORM
 	select BACKLIGHT_LCD_SUPPORT
 	select FB_MODE_HELPERS
 	select FB_SYS_FILLRECT

index f673186..b9ec64b 100644
@@ -15,7 +15,6 @@ obj-$(CONFIG_FB_WMT_GE_ROPS)   += wmt_ge_rops.o
 obj-$(CONFIG_FB_AMIGA)            += amifb.o c2p_planar.o
 obj-$(CONFIG_FB_ARC)              += arcfb.o
 obj-$(CONFIG_FB_CLPS711X)	  += clps711x-fb.o
-obj-$(CONFIG_FB_CLPS711X_OLD)	  += clps711xfb.o
 obj-$(CONFIG_FB_CYBER2000)        += cyber2000fb.o
 obj-$(CONFIG_FB_GRVGA)            += grvga.o
 obj-$(CONFIG_FB_PM2)              += pm2fb.o

index 90542db..7a13e5a 100644
@@ -353,20 +353,6 @@ config ARM_SINGLE_ARMV7M
 	select SPARSE_IRQ
 	select USE_OF
 
-
-config ARCH_CLPS711X
-	bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
-	select ARCH_REQUIRE_GPIOLIB
-	select AUTO_ZRELADDR
-	select CLKSRC_MMIO
-	select COMMON_CLK
-	select CPU_ARM720T
-	select GENERIC_CLOCKEVENTS
-	select MFD_SYSCON
-	select SOC_BUS
-	help
-	  Support for Cirrus Logic 711x/721x/731x based boards.
-
 config ARCH_GEMINI
 	bool "Cortina Systems Gemini"
 	select ARCH_REQUIRE_GPIOLIB

index 274e8a6..10f16b3 100644
@@ -140,7 +140,6 @@ head-y		:= arch/arm/kernel/head$(MMUEXT).o
 # Text offset. This list is sorted numerically by address in order to
 # provide a means to avoid/resolve conflicts in multi-arch kernels.
 textofs-y	:= 0x00008000
-textofs-$(CONFIG_ARCH_CLPS711X) := 0x00028000
 # We don't want the htc bootloader to corrupt kernel during resume
 textofs-$(CONFIG_PM_H1940)      := 0x00108000
 # SA1111 DMA bug: we don't want the kernel to live in precious DMA-able memory

index 0a170e1..3b56197 100644
@@ -1,16 +1,15 @@
-if ARCH_CLPS711X
-
-menu "CLPS711X/EP721X/EP731X Implementations"
-
-config MACH_CLPS711X_DT
-	bool "Device-tree support"
+menuconfig ARCH_CLPS711X
+	bool "Cirrus Logic EP721x/EP731x-based"
+	depends on ARCH_MULTI_V4T
+	select ARCH_REQUIRE_GPIOLIB
+	select AUTO_ZRELADDR
+	select CLKSRC_MMIO
 	select CLKSRC_OF
+	select COMMON_CLK
+	select CPU_ARM720T
+	select GENERIC_CLOCKEVENTS
+	select MFD_SYSCON
 	select OF_IRQ
 	select USE_OF
 	help
-	  Select this if you want to experiment device-tree with
-	  ARMv4T Cirrus Logic chips.
-
-endmenu
-
-endif
+	  Select this if you use ARMv4T Cirrus Logic chips.

index d79d998..bd0b7b5 100644
@@ -1 +1 @@
-obj-$(CONFIG_MACH_CLPS711X_DT)	+= board-dt.o
+obj-y += board-dt.o

new file mode 100644
index 0000000..433eebb
@@ -0,0 +1,106 @@
+CONFIG_KERNEL_LZMA=y
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_SLOB=y
+CONFIG_JUMP_LABEL=y
+# CONFIG_LBDAF is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91RM9200=y
+CONFIG_ARCH_CLPS711X=y
+CONFIG_ARCH_INTEGRATOR=y
+CONFIG_ARCH_INTEGRATOR_AP=y
+CONFIG_INTEGRATOR_IMPD1=y
+CONFIG_INTEGRATOR_CM720T=y
+CONFIG_INTEGRATOR_CM920T=y
+CONFIG_INTEGRATOR_CM922T_XA10=y
+CONFIG_ARCH_MXC=y
+CONFIG_MACH_SCB9328=y
+CONFIG_MACH_APF9328=y
+CONFIG_MACH_IMX1_DT=y
+CONFIG_ARCH_NSPIRE=y
+CONFIG_AEABI=y
+# CONFIG_ATAGS is not set
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CPU_IDLE=y
+CONFIG_ARM_CPUIDLE=y
+CONFIG_ARM_CLPS711X_CPUIDLE=y
+# CONFIG_COREDUMP is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_PLATRAM=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_GPIO=y
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_CLPS711X=y
+CONFIG_SERIAL_CLPS711X_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_I2C_IMX=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_SPI_CLPS711X=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_IMX=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_GPIO_74XX_MMIO=y
+CONFIG_GPIO_CLPS711X=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_GPIO_SYSCON=y
+CONFIG_W1=y
+CONFIG_W1_MASTER_MXC=y
+CONFIG_W1_MASTER_GPIO=y
+CONFIG_POWER_RESET_AT91_POWEROFF=y
+CONFIG_POWER_RESET_AT91_RESET=y
+CONFIG_POWER_RESET_AT91_SAMA5D2_SHDWC=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_POWER_RESET_SYSCON_POWEROFF=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_GPIO_WATCHDOG=y
+CONFIG_AT91RM9200_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_FB=y
+CONFIG_FB_CLPS711X=y
+CONFIG_FB_IMX=y
+CONFIG_LCD_PLATFORM=y
+CONFIG_BACKLIGHT_PWM=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_CLPS711X=y
+CONFIG_PWM_IMX=y
+CONFIG_EXT2_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_CRAMFS=y
+CONFIG_MINIX_FS=y
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRC_CCITT=y