misc: Add simple driver for some Nuvoton NCT6102D devices
PATCH v3 1/1 misc: Add simple driver for some Nuvoton NCT6102D devices
This simple driver provides some functions to control some of the integrated devices. The watchdog is enabled per default. This driver adds a function to disable the watchdog. Also the internal legacy UART (io address 0x3f8/0x2f8) is enabled per default.
---
v3:
- Remove misleading comment about UART
v2:
- Added macros for the constants as suggested by Bin
- Changed macro names as suggested by Bin
drivers/misc/Kconfig | 8 ++++++ drivers/misc/Makefile | 1 + drivers/misc/nuvoton_nct6102d.c | 56 +++++++++++++++++++++++++++++++++++++++++ include/nuvoton_nct6102d.h | 34 +++++++++++++++++++++++++ 4 files changed, 99 insertions(+) create mode 100644 drivers/misc/nuvoton_nct6102d.c create mode 100644 include/nuvoton_nct6102d.h
drivers/misc/Kconfig +8 -0
@@ -90,6 +90,14 @@ config MXC_OCOTP Programmable memory pages that are stored on the some Freescale i.MX processors. +config NUVOTON_NCT6102D + bool "Enable Nuvoton NCT6102D Super I/O driver" + help + If you say Y here, you will get support for the Nuvoton + NCT6102D Super I/O driver. This can be used to enable or + disable the legacy UART, the watchdog or other devices + in the Nuvoton Super IO chips on X86 platforms. + config PWRSEQ bool "Enable power-sequencing drivers" depends on DM
drivers/misc/Makefile +1 -0
@@ -24,6 +24,7 @@ obj-$(CONFIG_I2C_EEPROM) += i2c_eeprom.o obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o obj-$(CONFIG_MXC_OCOTP) += mxc_ocotp.o obj-$(CONFIG_MXS_OCOTP) += mxs_ocotp.o +obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o obj-$(CONFIG_NS87308) += ns87308.o obj-$(CONFIG_PDSP188x) += pdsp188x.o obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
drivers/misc/nuvoton_nct6102d.c new file +56 -0
56 lines not on this page · raw message
include/nuvoton_nct6102d.h new file +34 -0
@@ -0,0 +1,34 @@ +/* +* Copyright (C) 2016 Stefan Roese <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _NUVOTON_NCT6102D_H_ +#define _NUVOTON_NCT6102D_H_ + +/* I/O address of Nuvoton Super IO chip */ +#define NCT6102D_IO_PORT 0x4e + +/* Extended Function Enable Registers */ +#define NCT_EFER (NCT6102D_IO_PORT + 0) +/* Extended Function Index Register (same as EFER) */ +#define NCT_EFIR (NCT6102D_IO_PORT + 0) +/* Extended Function Data Register */ +#define NCT_EFDR (NCT_EFIR + 1) + +#define NCT_LD_SELECT_REG 0x07 + +/* Logical device number */ +#define NCT6102D_LD_UARTA 0x02 +#define NCT6102D_LD_WDT 0x08 + +#define NCT6102D_UARTA_ENABLE 0x30 +#define NCT6102D_WDT_TIMEOUT 0xf1 + +#define NCT_ENTRY_KEY 0x87 +#define NCT_EXIT_KEY 0xaa + +int nct6102d_wdt_disable (void ); + +#endif /* _NUVOTON_NCT6102D_H_ */
Signature · 1 line
2.9.2
PATCH v3 1/1 misc: Add simple driver for some Nuvoton NCT6102D devices
Quoted 16 lines · Stefan Roese
This simple driver provides some functions to control some of the integrated devices. The watchdog is enabled per default. This driver adds a function to disable the watchdog. Also the internal legacy UART (io address 0x3f8/0x2f8) is enabled per default.
Signed-off-by Stefan Roese <[email protected]>Reviewed-by Bin Meng <[email protected]>Cc Simon Glass <[email protected]>---
v3:
- Remove misleading comment about UARTv2:
- Added macros for the constants as suggested by Bin
- Changed macro names as suggested by Bin
Quoted 8 lines
drivers/misc/Kconfig | 8 ++++++ drivers/misc/Makefile | 1 + drivers/misc/nuvoton_nct6102d.c | 56 +++++++++++++++++++++++++++++++++++++++++ include/nuvoton_nct6102d.h | 34 +++++++++++++++++++++++++ 4 files changed, 99 insertions(+) create mode 100644 drivers/misc/nuvoton_nct6102d.c create mode 100644 include/nuvoton_nct6102d.h
applied to u-boot-x86, thanks!