Skip to contentSkip to conversation

ARM: dts: sun8i: Add dt nodes for sdio wifi

PATCH New Hans de Goede 3 participants 13 messages Aug 26, 2016 – Sep 5, 2016

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover ARM: dts: sun8i: Add dt nodes for sdio wifi

Hi Maxime,

Now that Ulf has merged the post-power-on-delay-ms mmc-pwrseq patches in his mmc/next tree and Rob Herring has accepted the esp8089 dt bindings (and specifically the esp,crystal-26M-en property), these are ready for merging.

Thanks & Regards,

Hans

#1 lore raw

PATCH 1/3 ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407

The polaroid-mid2407 tablet has an esp8089 wifi chip, add a dt node describing it.

---
 .../boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts   | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts +42 -0
index e300442..4789aac 100644
@@ -47,4 +47,46 @@
 / {
 	model = "Polaroid MID2407PXE03 tablet";
 	compatible = "polaroid,mid2407pxe03", "allwinner,sun8i-a23";
+
+	aliases {
+		ethernet0 = &esp8089;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_pwrseq_pin_mid2407>;
+		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+		/* The esp8089 needs 200 ms after driving wifi-en high */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	esp8089: sdio_wifi at 1 {
+		compatible = "esp,esp8089";
+		reg = <1>;
+		esp,crystal-26M-en = <2>;
+	};
+};
+
+&mmc1_pins_a {
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&r_pio {
+	wifi_pwrseq_pin_mid2407: wifi_pwrseq_pin at 0 {
+		allwinner,pins = "PL6";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 };
Signature · 1 line
2.9.3
#2 lore raw

PATCH 1/3 ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407

Quoted 4 lines · Hans de Goede

The polaroid-mid2407 tablet has an esp8089 wifi chip, add a dt node describing it.

Applied, thanks!
Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160827/6fec7e29/attachment.sig>
#3 lore raw

PATCH 2/3 ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809

In reply to Hans de Goede

The polaroid-mid2809 tablet has an esp8089 wifi chip, add a dt node describing it.

---
 .../boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts   | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts +42 -0
index 6d06e24..c9213ca 100644
@@ -47,4 +47,46 @@
 / {
 	model = "Polaroid MID2809PXE04 tablet";
 	compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23";
+
+	aliases {
+		ethernet0 = &esp8089;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_pwrseq_pin_mid2809>;
+		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+		/* The esp8089 needs 200 ms after driving wifi-en high */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	esp8089: sdio_wifi at 1 {
+		compatible = "esp,esp8089";
+		reg = <1>;
+		esp,crystal-26M-en = <2>;
+	};
+};
+
+&mmc1_pins_a {
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&r_pio {
+	wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin at 0 {
+		allwinner,pins = "PL6";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 };
Signature · 1 line
2.9.3
#4 lore raw

PATCH 2/3 ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809

Quoted 4 lines · Hans de Goede

The polaroid-mid2809 tablet has an esp8089 wifi chip, add a dt node describing it.

Applied, Thanks!
Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160827/192cfdd3/attachment.sig>
#5 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

In reply to Hans de Goede

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and RTL8189FTV wifi controllers.

---
 arch/arm/boot/dts/sun8i-q8-common.dtsi | 49 ++++++++++++++++++++++++++++++++++
 1 file changed, 49 insertions(+)
arch/arm/boot/dts/sun8i-q8-common.dtsi +49 -0
index 60fa958..29f837a 100644
@@ -42,10 +42,59 @@
 #include "sunxi-reference-design-tablet.dtsi"
 #include "sun8i-reference-design-tablet.dtsi"
 
+/ {
+	aliases {
+		serial0 = &r_uart;
+		/* Make u-boot set mac-address for wifi without an eeprom */
+		ethernet0 = &sdio_wifi;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		/*
+		 * Q8 boards use various PL# pins as wifi-en. On other boards
+		 * these may be connected to a wifi module output pin. To avoid
+		 * short-circuits we configure these as inputs with pull-ups via
+		 * pinctrl, instead of listing them as active-low reset-gpios.
+		 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_pwrseq_pin_q8>;
+		/* The esp8089 needs 200 ms after driving wifi-en high */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
 &ehci0 {
 	status  = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: sdio_wifi at 1 {
+		reg = <1>;
+	};
+};
+
+&mmc1_pins_a {
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&r_pio {
+	wifi_pwrseq_pin_q8: wifi_pwrseq_pin at 0 {
+		allwinner,pins = "PL6", "PL7", "PL11";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_dldo1>;
 };
Signature · 1 line
2.9.3
#6 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

Quoted 8 lines · Hans de Goede

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

No, because that grabs PINs that might or might not be supposed to be used for that, it leaves clocks and regulators enabled, which draw power, to no end. And that's even worth since most boards will not use it.

You can put the definition of the nodes in the DTSI, but the final status will have to be in the (relevant) DTS.

Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160829/b1c25ce3/attachment.sig>
#7 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

Hi,

Quoted 10 lines · Maxime Ripard
Quoted 8 lines · Hans de Goede

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

Quoted 7 lines

No, because that grabs PINs that might or might not be supposed to be used for that, it leaves clocks and regulators enabled, which draw power, to no end. And that's even worth since most boards will not use it.

You can put the definition of the nodes in the DTSI, but the final status will have to be in the (relevant) DTS.

This is again the q8-tablet thing where china produces a new variant every 2 weeks. So we've sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts which try to be generic dts files for these tablets, since creating a custom dts per variant is madness.

This commit puts the node in sun8i-q8-common.dtsi because the A23 and A33 are pin compatible and we've tablets where the only difference is the SoC soldered on there, the use the _exact_ same PCB and components otherwise, so we have all the sun8i q8 stuff in a common place for sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts, those are the only users of this dtsi file.

You've already merged the bits which handle the variants with an USB attached wifi module (enabling ehci0 also on boards where nothing is connected). This is the counter-part for PCB's which use a sdio wifi module (about 90% of all boards in my experience). As for turning a regulator on unnecessary, both the wifi and sdio wifi solution use the same regulator, so that is already turned on through the usb bits and it needs to be in either case.

The only downside of this approach is that we either have the USB controller turned on unnecessarily (in most cases) or the mmc controller (in the rare A23 tablet which still uses an USB wifi module).

This all actually fits neatly into the plans to do hardware autodetection for these tablets which I'm working on, in this case we can just let the kernel handle things without additional code (think the beaglebone capemanager) since both busses are discoverable.

Once we have the q8-hardwaremgr I'm working on and hope to post an RFC of soon, we could even make that turn off the unused controller (as a future enhancement).

I hope this explains things.

Regards,

Hans

#8 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

Hi Hans,

Quoted 16 lines · Hans de Goede
Quoted 15 lines · Maxime Ripard
Quoted 8 lines · Hans de Goede

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

No, because that grabs PINs that might or might not be supposed to be used for that, it leaves clocks and regulators enabled, which draw power, to no end. And that's even worth since most boards will not use it.

Quoted 7 lines
Quoted 2 lines

You can put the definition of the nodes in the DTSI, but the final status will have to be in the (relevant) DTS.

This is again the q8-tablet thing where china produces a new variant every 2 weeks. So we've sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts which try to be generic dts files for these tablets, since creating a custom dts per variant is madness.

This is almost unrelated, and probably some wishful thinking, but I'd really prefer to support *one* board properly, with all its features, rather than supporting every random Allwinner device with half baked support, because no one ever updated the DT, or there's simply no driver. But hey, I can't force you to work on something either :)

Quoted 8 lines

This commit puts the node in sun8i-q8-common.dtsi because the A23 and A33 are pin compatible and we've tablets where the only difference is the SoC soldered on there, the use the _exact_ same PCB and components otherwise, so we have all the sun8i q8 stuff in a common place for sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts, those are the only users of this dtsi file.

Quoted 5 lines

You've already merged the bits which handle the variants with an USB attached wifi module (enabling ehci0 also on boards where nothing is connected). This is the counter-part for PCB's which use a sdio wifi module (about 90% of all boards in my experience).

I'm confused. Are most boards using an USB wifi chip, like you were stating in your commit log, or an SDIO wifi chip like you just said?

Quoted 3 lines

As for turning a regulator on unnecessary, both the wifi and sdio wifi solution use the same regulator, so that is already turned on through the usb bits and it needs to be in either case.

Ok, so indeed, that's not as bad as it sounds.

Quoted 11 lines

The only downside of this approach is that we either have the USB controller turned on unnecessarily (in most cases) or the mmc controller (in the rare A23 tablet which still uses an USB wifi module).

This all actually fits neatly into the plans to do hardware autodetection for these tablets which I'm working on, in this case we can just let the kernel handle things without additional code (think the beaglebone capemanager) since both busses are discoverable.

Quoted 3 lines

Once we have the q8-hardwaremgr I'm working on and hope to post an RFC of soon, we could even make that turn off the unused controller (as a future enhancement).

If that's on your to-do-list, that's fine by me.

Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160901/9ab81153/attachment.sig>
#9 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

Hi Maxime,

Quoted 27 lines · Maxime Ripard

Hi Hans,

Quoted 16 lines · Hans de Goede
Quoted 15 lines · Maxime Ripard
Quoted 8 lines · Hans de Goede

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

No, because that grabs PINs that might or might not be supposed to be used for that, it leaves clocks and regulators enabled, which draw power, to no end. And that's even worth since most boards will not use it.

Quoted 7 lines
Quoted 2 lines

You can put the definition of the nodes in the DTSI, but the final status will have to be in the (relevant) DTS.

This is again the q8-tablet thing where china produces a new variant every 2 weeks. So we've sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts which try to be generic dts files for these tablets, since creating a custom dts per variant is madness.

Quoted 5 lines

This is almost unrelated, and probably some wishful thinking, but I'd really prefer to support *one* board properly, with all its features, rather than supporting every random Allwinner device with half baked support, because no one ever updated the DT, or there's simply no driver. But hey, I can't force you to work on something either :)

The q8 tablets are somewhat special, to the end consumer they are one board, but they differ a lot per badge. These are 40 (or less) usd tablets, which get whatever wifi / touchscreen-controller / accelerometer which is cheapest on the Chenzen market when the badge gets produces.

For the end user to actually figure out what is in there requires opening the tablet, or poking around with adb to learn the exact internals / drivers used by android.

I actually own 10 of these (3 a13, 5 a23, 2 a33) and have access to 2 more a33 models which friends of me have, and they are *all* different. For a list of all tablets I've see:
https://github.com/jwrdegoede/sunxi-fedora-scripts/blob/master/hansg-tablet-info

Given the price of these they are really nice to thinker with / turn into a little normal linux touch device, so I would like to support them as best as we can in a somewhat user-friendly way. Also see the RFC patch for the q8-hardwaremgr I posted recently. In the end these tablets are the "*one* board" which I'm trying to support properly, except that they are only one board on the outside not on the outside.

TL;DR: q8 tablets are special, but also quite popular and I would like to support them properly, which requires some special handling.

Quoted 8 lines
Quoted 8 lines

This commit puts the node in sun8i-q8-common.dtsi because the A23 and A33 are pin compatible and we've tablets where the only difference is the SoC soldered on there, the use the _exact_ same PCB and components otherwise, so we have all the sun8i q8 stuff in a common place for sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts, those are the only users of this dtsi file.

Quoted 8 lines
Quoted 5 lines

You've already merged the bits which handle the variants with an USB attached wifi module (enabling ehci0 also on boards where nothing is connected). This is the counter-part for PCB's which use a sdio wifi module (about 90% of all boards in my experience).

I'm confused. Are most boards using an USB wifi chip, like you were stating in your commit log, or an SDIO wifi chip like you just said?

My bad, the commit msg. is wrong of the 9 sun8i q8 tablets I've access to only 1 uses usb wifi.

So the first part of the commit msg should read "Most of the sun8i q8 boards have a sdio wifi controller"

Quoted 17 lines
Quoted 3 lines

As for turning a regulator on unnecessary, both the wifi and sdio wifi solution use the same regulator, so that is already turned on through the usb bits and it needs to be in either case.

Ok, so indeed, that's not as bad as it sounds.

Quoted 11 lines

The only downside of this approach is that we either have the USB controller turned on unnecessarily (in most cases) or the mmc controller (in the rare A23 tablet which still uses an USB wifi module).

This all actually fits neatly into the plans to do hardware autodetection for these tablets which I'm working on, in this case we can just let the kernel handle things without additional code (think the beaglebone capemanager) since both busses are discoverable.

Quoted 5 lines
Quoted 3 lines

Once we have the q8-hardwaremgr I'm working on and hope to post an RFC of soon, we could even make that turn off the unused controller (as a future enhancement).

If that's on your to-do-list, that's fine by me.

I've just added it to my to-do list :)

So I assume with that done, that you are ok with taking this patch now ? Please fixup the commit msg mistake, or let me know if you want a v2.

Regards,

Hans

#10 lore raw

PATCH 3/3 ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers

Hi,

Quoted 102 lines · Hans de Goede
Quoted 25 lines · Hans de Goede
Quoted 16 lines · Maxime Ripard
Quoted 15 lines · Hans de Goede
Quoted 8 lines

Most of the sun8i q8 boards have an usb wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller.

The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg.

No, because that grabs PINs that might or might not be supposed to be used for that, it leaves clocks and regulators enabled, which draw power, to no end. And that's even worth since most boards will not use it.

Quoted 7 lines
Quoted 2 lines

You can put the definition of the nodes in the DTSI, but the final status will have to be in the (relevant) DTS.

This is again the q8-tablet thing where china produces a new variant every 2 weeks. So we've sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts which try to be generic dts files for these tablets, since creating a custom dts per variant is madness.

Quoted 5 lines

This is almost unrelated, and probably some wishful thinking, but I'd really prefer to support *one* board properly, with all its features, rather than supporting every random Allwinner device with half baked support, because no one ever updated the DT, or there's simply no driver. But hey, I can't force you to work on something either :)

The q8 tablets are somewhat special, to the end consumer they are one board, but they differ a lot per badge. These are 40 (or less) usd tablets, which get whatever wifi / touchscreen-controller / accelerometer which is cheapest on the Chenzen market when the badge gets produces.

For the end user to actually figure out what is in there requires opening the tablet, or poking around with adb to learn the exact internals / drivers used by android.

I actually own 10 of these (3 a13, 5 a23, 2 a33) and have access to 2 more a33 models which friends of me have, and they are *all* different. For a list of all tablets I've see:
https://github.com/jwrdegoede/sunxi-fedora-scripts/blob/master/hansg-tablet-info

Given the price of these they are really nice to thinker with / turn into a little normal linux touch device, so I would like to support them as best as we can in a somewhat user-friendly way. Also see the RFC patch for the q8-hardwaremgr I posted recently. In the end these tablets are the "*one* board" which I'm trying to support properly, except that they are only one board on the outside not on the outside.

TL;DR: q8 tablets are special, but also quite popular and I would like to support them properly, which requires some special handling.

Quoted 8 lines
Quoted 8 lines

This commit puts the node in sun8i-q8-common.dtsi because the A23 and A33 are pin compatible and we've tablets where the only difference is the SoC soldered on there, the use the _exact_ same PCB and components otherwise, so we have all the sun8i q8 stuff in a common place for sun8i-a23-q8-tablet.dts and sun8i-a33-q8-tablet.dts, those are the only users of this dtsi file.

Quoted 8 lines
Quoted 5 lines

You've already merged the bits which handle the variants with an USB attached wifi module (enabling ehci0 also on boards where nothing is connected). This is the counter-part for PCB's which use a sdio wifi module (about 90% of all boards in my experience).

I'm confused. Are most boards using an USB wifi chip, like you were stating in your commit log, or an SDIO wifi chip like you just said?

My bad, the commit msg. is wrong of the 9 sun8i q8 tablets I've access to only 1 uses usb wifi.

So the first part of the commit msg should read "Most of the sun8i q8 boards have a sdio wifi controller"

Quoted 21 lines
Quoted 3 lines

As for turning a regulator on unnecessary, both the wifi and sdio wifi solution use the same regulator, so that is already turned on through the usb bits and it needs to be in either case.

Ok, so indeed, that's not as bad as it sounds.

Quoted 14 lines

The only downside of this approach is that we either have the USB controller turned on unnecessarily (in most cases) or the mmc controller (in the rare A23 tablet which still uses an USB wifi module).

This all actually fits neatly into the plans to do hardware autodetection for these tablets which I'm working on, in this case we can just let the kernel handle things without additional code (think the beaglebone capemanager) since both busses are discoverable.

Once we have the q8-hardwaremgr I'm working on and hope to post an RFC of soon, we could even make that turn off the unused controller (as a future enhancement).

Quoted 7 lines
Quoted 1 line

If that's on your to-do-list, that's fine by me.

I've just added it to my to-do list :)

So I assume with that done, that you are ok with taking this patch now ? Please fixup the commit msg mistake, or let me know if you want a v2.

Yeah, I just applied it and fixed the commit log.

Thanks!
Maxime

Signature · 10 lines
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160905/e13d4468/attachment.sig>
#11 lore raw

cover ARM: dts: sun8i: Add dt nodes for sdio wifi

In reply to Hans de Goede

26.08.2016, 22:58, "Hans de Goede" <[email protected]>:

Quoted 6 lines

Hi Maxime,

Now that Ulf has merged the post-power-on-delay-ms mmc-pwrseq patches in his mmc/next tree and Rob Herring has accepted the esp8089 dt bindings (and specifically the esp,crystal-26M-en property), these are ready for merging.

Can the driver now work without broken-cd?

Quoted 9 lines

Thanks & Regards,

Hans

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#12 lore raw

cover ARM: dts: sun8i: Add dt nodes for sdio wifi

Hi,

Quoted 11 lines · Icenowy Zheng

26.08.2016, 22:58, "Hans de Goede" <[email protected]>:

Quoted 6 lines

Hi Maxime,

Now that Ulf has merged the post-power-on-delay-ms mmc-pwrseq patches in his mmc/next tree and Rob Herring has accepted the esp8089 dt bindings (and specifically the esp,crystal-26M-en property), these are ready for merging.

Can the driver now work without broken-cd?

Sort-off, my fork of the esp8089 driver has a workaround so that it does not need broken-cd. I'm also working together with Ulf (the mmc maintainer) to come up with a clean upstream solution for this.

Regards,

Hans