Skip to contentSkip to conversation

Patches for Aria G25 board based on Buildroot 2016.08

PATCH New Biagio Montaruli 3 participants 12 messages Sep 22, 2016 Arm/Microchip (AT91) SoC support

lore
Share & tools
lore

Biagio Montaruli

author
#0 lore raw

PATCH 1/3 Patches for Aria G25 board based on Buildroot 2016.08

- configs/acmesystems_aria_g25_128mb_defconfig, configs/acmesystems_aria_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/aria-g25/genimage.cfg board/acmesystems/aria-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/aria-g25/readme.txt : update documentation for Aria G25 and add notes about how to build sdcard.img

Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/aria-g25/genimage.cfg      | 35 +++++++++++++++++
 board/acmesystems/aria-g25/post-image.sh     | 14 +++++++
 board/acmesystems/aria-g25/readme.txt        | 56 ++++++++++++----------------
 configs/acmesystems_aria_g25_128mb_defconfig | 30 +++++++++++----
 configs/acmesystems_aria_g25_256mb_defconfig | 30 +++++++++++----
 5 files changed, 118 insertions(+), 47 deletions(-)
 create mode 100644 board/acmesystems/aria-g25/genimage.cfg
 create mode 100755 board/acmesystems/aria-g25/post-image.sh
board/acmesystems/aria-g25/genimage.cfg new file +35 -0
new file mode 100644
index 0000000..2e2eb12
@@ -0,0 +1,35 @@
+# Minimal SD card image for the Acmesystems Aria G25
+
+image boot.vfat {
+	vfat {
+		file zImage {
+			image = "zImage"
+		}
+
+		file at91-ariag25.dtb {
+			image = "at91-ariag25.dtb"
+		}
+
+		file boot.bin {
+			image = "at91sam9x5_aria-sdcardboot-linux-zimage-dt-3.8.6.bin"
+		}
+	}
+	size = 16M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+		size = 512M
+	}
+}
board/acmesystems/aria-g25/post-image.sh new file +14 -0
new file mode 100755
index 0000000..2846f56
@@ -0,0 +1,14 @@
+#!/bin/sh
+
+BOARD_DIR="$(dirname $0)"
+GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg"
+GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
+
+rm -rf "${GENIMAGE_TMP}"
+
+genimage  \
+	--rootpath "${TARGET_DIR}"     \
+	--tmppath "${GENIMAGE_TMP}"    \
+	--inputpath "${BINARIES_DIR}"  \
+	--outputpath "${BINARIES_DIR}" \
+	--config "${GENIMAGE_CFG}"
board/acmesystems/aria-g25/readme.txt +23 -33

74 lines not on this page · raw message

configs/acmesystems_aria_g25_128mb_defconfig +23 -7
index c4d2cd6..0ec210f 100644
@@ -1,20 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Linux headers same as kernel, a 4.1 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Aria-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/aria-g25/post-image.sh"
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
 
-# Bootloader
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
+
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/tanzilli/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="3f957cec253abc80fd10c733e5e596f46e1aef56"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="aria-128m"
+
+# Tools to build sdcard.img
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_aria_g25_256mb_defconfig +23 -7
index ba191c6..a480287 100644
@@ -1,20 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Linux headers same as kernel, a 4.1 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Aria-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/aria-g25/post-image.sh"
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
 
-# Bootloader
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
+
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/tanzilli/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="3f957cec253abc80fd10c733e5e596f46e1aef56"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="aria-256m"
+
+# Tools to build sdcard.img
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33 ++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36 ++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36 ++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -6
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
 	vfat {
 		file zImage {
 			image = "zImage"
 		}
-
+		
 		file acme-arietta.dtb {
-			image = "at91-ariag25.dtb"
+			image = "at91-ariettag25.dtb"
 		}
-
+		
 		file boot.bin {
-			image = "at91sam9x5_arietta-sdcardboot-linux-zimage-dt-3.7.bin"
-		}
+			image = "at91sam9x5_arietta-sdcardboot-linux-zimage-dt-3.8.6.bin"
+		} 
 	}
 	size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
 	--rootpath "${TARGET_DIR}"     \
 	--tmppath "${GENIMAGE_TMP}"    \
 	--inputpath "${BINARIES_DIR}"  \
 	--outputpath "${BINARIES_DIR}" \
 	--config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +14 -19
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-
-Intro
-=====
-
-This default configuration will allow you to start experimenting with the
-buildroot environment for the Arietta G25. With the current configuration
-it will bring-up the board, and allow access through the serial console.
-
-You can find additional informations, tutorials and a very comprehensive
-documentation on http://www.acmesystems.it/arietta.
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:
 

@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration choosed type:
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make
 

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called "sdcard.img"
 in the output/images/ directory.
 
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with "dd" command:
 
   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
 
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (http://www.acmesystems.it/DPI)
 
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)
+You can find additional informations, tutorials and a very comprehensive
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +21 -15
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25/post-image.sh"
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/tanzilli/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b36695b715f469f4872f47e5cc8115000"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25/post-image.sh"
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +21 -15
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25/post-image.sh"
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/tanzilli/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b36695b715f469f4872f47e5cc8115000"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25/post-image.sh"
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
Signature · 1 line
2.7.4
#2 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 11 lines

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

As stated by Thomas in a previous review this patch should have a subject like:

configs/acmesystems_arietta_g25: updated kernel ad at91bootstrap

You should do the same for the Aria patch.

Quoted 71 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33
++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36
++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36
++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -8
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
        vfat {
                file zImage {
                        image = "zImage"
                }
-
+
                file acme-arietta.dtb {
-                       image = "at91-ariag25.dtb"
+                       image = "at91-ariettag25.dtb"
                }
-
+
                file boot.bin {
-                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.7.bin"
-               }
+                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.8.6.bin"
+               }
        }
        size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
        --rootpath "${TARGET_DIR}"     \
        --tmppath "${GENIMAGE_TMP}"    \
        --inputpath "${BINARIES_DIR}"  \
        --outputpath "${BINARIES_DIR}" \
        --config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +0 -2
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-

board/acmesystems/arietta-g25/readme.txt line 1

Quoted 10 lines
board/acmesystems/arietta-g25/readme.txt +0 -9
-Intro
-=====
-
-This default configuration will allow you to start experimenting with the
-buildroot environment for the Arietta G25. With the current configuration
-it will bring-up the board, and allow access through the serial console.
-
-You can find additional informations, tutorials and a very comprehensive
-documentation on http://www.acmesystems.it/arietta.

Why remove this paragraph?

Quoted 13 lines
board/acmesystems/arietta-g25/readme.txt +3 -2
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:

board/acmesystems/arietta-g25/readme.txt else for 256MB RAM variant type: · line 18

Quoted 6 lines
board/acmesystems/arietta-g25/readme.txt +1 -1
@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration chosen type:

Typo: chosen not choosed

Quoted 25 lines
board/acmesystems/arietta-g25/readme.txt +4 -0
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called

"sdcard.img"
in the output/images/ directory.

board/acmesystems/arietta-g25/readme.txt +1 -1
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with "dd"

command:

   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/acmesystems/arietta-g25/readme.txt +3 -1
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (

http://www.acmesystems.it/DPI)

board/acmesystems/arietta-g25/readme.txt How to write the microSD card · line 45

Quoted 3 lines
board/acmesystems/arietta-g25/readme.txt +0 -3
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)

I prefer this paragraph to the one you proposed ;)

Quoted 134 lines
board/acmesystems/arietta-g25/readme.txt +2 -0
+You can find additional informations, tutorials and a very comprehensive
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +7 -3
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.

com/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github. com/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_128mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +2 -4
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +7 -3
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.

com/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github. com/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_256mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +2 -5
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
--

2.7.4

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

Signature · 4 lines
Profile: http://it.linkedin.com/in/compagnucciangelo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/6801257a/attachment.html>
author
#3 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

Hi Angelo,
for that patch I have used "Patches for Arietta G25 board based on Buildroot 2016.08" as title because it adds changes to different files and not only to the default configuration files of Arietta. Notice that I have listed the files modified and a summary of changes made to the relative files including the configuration files for Arietta; anyway I will send a new patch for Arietta with the title suggested by you (configs/acmesystems_arietta_g25: updated kernel and at91bootstrap3)

I will also include your suggestions for the readme.txt file in the new patch. Can I use the name "Arietta" instead of "arietta" in the readme.txt file ?

Best regards.
Biagio

2016-09-22 12:14 GMT+02:00 Angelo Compagnucci <[email protected]> :

Quoted 293 lines

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 11 lines

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

As stated by Thomas in a previous review this patch should have a subject like:

configs/acmesystems_arietta_g25: updated kernel ad at91bootstrap

You should do the same for the Aria patch.

Quoted 71 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33
++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36
++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36
++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -8
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
        vfat {
                file zImage {
                        image = "zImage"
                }
-
+
                file acme-arietta.dtb {
-                       image = "at91-ariag25.dtb"
+                       image = "at91-ariettag25.dtb"
                }
-
+
                file boot.bin {
-                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.7.bin"
-               }
+                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.8.6.bin"
+               }
        }
        size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
        --rootpath "${TARGET_DIR}"     \
        --tmppath "${GENIMAGE_TMP}"    \
        --inputpath "${BINARIES_DIR}"  \
        --outputpath "${BINARIES_DIR}" \
        --config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +0 -2
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-

board/acmesystems/arietta-g25/readme.txt line 1

Quoted 10 lines
board/acmesystems/arietta-g25/readme.txt +0 -9
-Intro
-=====
-
-This default configuration will allow you to start experimenting with the
-buildroot environment for the Arietta G25. With the current configuration
-it will bring-up the board, and allow access through the serial console.
-
-You can find additional informations, tutorials and a very comprehensive
-documentation on http://www.acmesystems.it/arietta.

Why remove this paragraph?

Quoted 13 lines
board/acmesystems/arietta-g25/readme.txt +3 -2
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:

board/acmesystems/arietta-g25/readme.txt else for 256MB RAM variant type: · line 18

Quoted 6 lines
board/acmesystems/arietta-g25/readme.txt +1 -1
@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration chosen type:

Typo: chosen not choosed

Quoted 25 lines
board/acmesystems/arietta-g25/readme.txt +4 -0
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called

"sdcard.img"
in the output/images/ directory.

board/acmesystems/arietta-g25/readme.txt +1 -1
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with "dd"

command:

   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/acmesystems/arietta-g25/readme.txt +3 -1
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (

http://www.acmesystems.it/DPI)

board/acmesystems/arietta-g25/readme.txt How to write the microSD card · line 45

Quoted 3 lines
board/acmesystems/arietta-g25/readme.txt +0 -3
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)

I prefer this paragraph to the one you proposed ;)

Quoted 129 lines
board/acmesystems/arietta-g25/readme.txt +2 -0
+You can find additional informations, tutorials and a very comprehensive
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +7 -3
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_128mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +2 -4
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +7 -3
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_256mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +2 -5
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
--

2.7.4

Quoted 11 lines
Quoted 5 lines

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

--
Profile: http://it.linkedin.com/in/compagnucciangelo

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/7ffe1f9c/attachment.html>

#4 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

Hi Biagio,

2016-09-22 16:06 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 9 lines

Hi Angelo,
for that patch I have used "Patches for Arietta G25 board based on Buildroot 2016.08" as title because it adds changes to different files and not only to the default configuration files of Arietta. Notice that I have listed the files modified and a summary of changes made to the relative files including the configuration files for Arietta; anyway I will send a new patch for Arietta with the title suggested by you (configs/acmesystems_arietta_g25: updated kernel and at91bootstrap3)

The general rule is to be atomic in patch subject and content, in your case is more than normal that upgrading a configuration involves touching also board files.

Quoted 4 lines

I will also include your suggestions for the readme.txt file in the new patch. Can I use the name "Arietta" instead of "arietta" in the readme.txt file ?

Yes, sure!

Sincerely, Angelo

Quoted 315 lines

Best regards.
Biagio

2016-09-22 12:14 GMT+02:00 Angelo Compagnucci <
angelo.compagnucci at gmail.com>:

Quoted 306 lines

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 11 lines

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

As stated by Thomas in a previous review this patch should have a subject like:

configs/acmesystems_arietta_g25: updated kernel ad at91bootstrap

You should do the same for the Aria patch.

Quoted 79 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33
++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36
++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36
++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -8
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
        vfat {
                file zImage {
                        image = "zImage"
                }
-
+
                file acme-arietta.dtb {
-                       image = "at91-ariag25.dtb"
+                       image = "at91-ariettag25.dtb"
                }
-
+
                file boot.bin {
-                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.7.bin"
-               }
+                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.8.6.bin"
+               }
        }
        size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
        --rootpath "${TARGET_DIR}"     \
        --tmppath "${GENIMAGE_TMP}"    \
        --inputpath "${BINARIES_DIR}"  \
        --outputpath "${BINARIES_DIR}" \
        --config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +0 -6
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-
-Intro
-=====
-
-This default configuration will allow you to start experimenting with

the
-buildroot environment for the Arietta G25. With the current configuration

board/acmesystems/arietta-g25/readme.txt line 11

Quoted 4 lines
board/acmesystems/arietta-g25/readme.txt +0 -4
-it will bring-up the board, and allow access through the serial console.
-
-You can find additional informations, tutorials and a very comprehensive
-documentation on http://www.acmesystems.it/arietta.

Why remove this paragraph?

Quoted 13 lines
board/acmesystems/arietta-g25/readme.txt +3 -2
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:

board/acmesystems/arietta-g25/readme.txt else for 256MB RAM variant type: · line 18

Quoted 6 lines
board/acmesystems/arietta-g25/readme.txt +1 -1
@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration chosen type:

Typo: chosen not choosed

Quoted 25 lines
board/acmesystems/arietta-g25/readme.txt +4 -0
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called

"sdcard.img"
in the output/images/ directory.

board/acmesystems/arietta-g25/readme.txt +1 -1
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with "dd"

command:

   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/acmesystems/arietta-g25/readme.txt +3 -1
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (

http://www.acmesystems.it/DPI)

board/acmesystems/arietta-g25/readme.txt How to write the microSD card · line 45

Quoted 3 lines
board/acmesystems/arietta-g25/readme.txt +0 -3
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)

I prefer this paragraph to the one you proposed ;)

Quoted 129 lines
board/acmesystems/arietta-g25/readme.txt +2 -0
+You can find additional informations, tutorials and a very comprehensive
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +7 -3
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_128mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +2 -4
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +7 -3
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_256mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +2 -5
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
--

2.7.4

Quoted 5 lines

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

--
Profile: http://it.linkedin.com/in/compagnucciangelo

Signature · 4 lines
Profile: http://it.linkedin.com/in/compagnucciangelo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/a1b09d2a/attachment.html>
author
#5 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

Hi Angelo,
what do you think about this version of "readme.txt" file for Arietta ? Is it good ?

Acme Systems Arietta G25

Quoted 42 lines

Intro
===

This default configuration will allow you to start experimenting with the buildroot environment for the Arietta G25. With the current configuration it will bring-up the board, and allow access through the serial console.

You can find additional informations, tutorials and a very comprehensive documentation on http://www.acmesystems.it/arietta.

Build instructions
=============

To build an image for the Arietta G25 choose the configuration corresponding to the Arietta variant.

For 128MB RAM variant type:

$ make acmesystems_arietta_g25_128mb_defconfig

else for 256MB RAM variant type:

$ make acmesystems_arietta_g25_256mb_defconfig

To customize the configuration chosen type:

$ make menuconfig

When you are ready to start building Buildroot type:

$ make

How to write the microSD card
======================

Once the build process is finished you will have an image called "sdcard.img"
in the output/images/ directory.

Copy the bootable "sdcard.img" onto an SD card with "dd":

Quoted 8 lines
  $ sudo dd if=output/images/sdcard.img of=/dev/sdX

Insert the microSD card into the Arietta slot and power it.

The image just built is fairly basic and the only output you will get is on serial console, please consider to use a DPI cable (http://www.acmesystems.it/DPI)

If for you it's OK, I will include it in the patch for Arietta.

Best regards,
Biagio.

2016-09-22 16:18 GMT+02:00 Angelo Compagnucci <[email protected]> :

Quoted 349 lines

Hi Biagio,

2016-09-22 16:06 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 9 lines

Hi Angelo,
for that patch I have used "Patches for Arietta G25 board based on Buildroot 2016.08" as title because it adds changes to different files and not only to the default configuration files of Arietta. Notice that I have listed the files modified and a summary of changes made to the relative files including the configuration files for Arietta; anyway I will send a new patch for Arietta with the title suggested by you (configs/acmesystems_arietta_g25: updated kernel and at91bootstrap3)

The general rule is to be atomic in patch subject and content, in your case is more than normal that upgrading a configuration involves touching also board files.

Quoted 4 lines

I will also include your suggestions for the readme.txt file in the new patch. Can I use the name "Arietta" instead of "arietta" in the readme.txt file ?

Yes, sure!

Sincerely, Angelo

Quoted 318 lines

Best regards.
Biagio

2016-09-22 12:14 GMT+02:00 Angelo Compagnucci <
angelo.compagnucci at gmail.com>:

Quoted 309 lines

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 11 lines

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

As stated by Thomas in a previous review this patch should have a subject like:

configs/acmesystems_arietta_g25: updated kernel ad at91bootstrap

You should do the same for the Aria patch.

Quoted 82 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33
++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36
++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36
++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -8
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
        vfat {
                file zImage {
                        image = "zImage"
                }
-
+
                file acme-arietta.dtb {
-                       image = "at91-ariag25.dtb"
+                       image = "at91-ariettag25.dtb"
                }
-
+
                file boot.bin {
-                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.7.bin"
-               }
+                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.8.6.bin"
+               }
        }
        size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
        --rootpath "${TARGET_DIR}"     \
        --tmppath "${GENIMAGE_TMP}"    \
        --inputpath "${BINARIES_DIR}"  \
        --outputpath "${BINARIES_DIR}" \
        --config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +0 -6
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-
-Intro
-=====
-
-This default configuration will allow you to start experimenting with

the
-buildroot environment for the Arietta G25. With the current configuration
-it will bring-up the board, and allow access through the serial console.

board/acmesystems/arietta-g25/readme.txt +0 -2
-
-You can find additional informations, tutorials and a very
Quoted 3 lines

comprehensive
-documentation on http://www.acmesystems.it/arietta.

Why remove this paragraph?

Quoted 13 lines
board/acmesystems/arietta-g25/readme.txt +3 -2
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:

board/acmesystems/arietta-g25/readme.txt else for 256MB RAM variant type: · line 18

Quoted 6 lines
board/acmesystems/arietta-g25/readme.txt +1 -1
@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration chosen type:

Typo: chosen not choosed

Quoted 25 lines
board/acmesystems/arietta-g25/readme.txt +4 -0
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called

"sdcard.img"
in the output/images/ directory.

board/acmesystems/arietta-g25/readme.txt +1 -1
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with

"dd" command:

   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/acmesystems/arietta-g25/readme.txt +3 -1
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (

http://www.acmesystems.it/DPI)

board/acmesystems/arietta-g25/readme.txt How to write the microSD card · line 45

Quoted 3 lines
board/acmesystems/arietta-g25/readme.txt +0 -3
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)

I prefer this paragraph to the one you proposed ;)

Quoted 130 lines

+You can find additional informations, tutorials and a very comprehensive

board/acmesystems/arietta-g25/readme.txt +1 -0
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +7 -3
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_128mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +2 -4
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +7 -3
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_256mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +2 -5
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
--

2.7.4

Quoted 5 lines

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

--
Profile: http://it.linkedin.com/in/compagnucciangelo

Quoted 3 lines

--
Profile: http://it.linkedin.com/in/compagnucciangelo

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/4083daae/attachment.html>

#6 lore raw

PATCH 2/3 Patches for Arietta G25 board based on Buildroot 2016.08

Hi Biagio!

2016-09-22 16:25 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 49 lines

Hi Angelo,
what do you think about this version of "readme.txt" file for Arietta ? Is it good ?

Acme Systems Arietta G25

Quoted 44 lines

Intro
===

This default configuration will allow you to start experimenting with the buildroot environment for the Arietta G25. With the current configuration it will bring-up the board, and allow access through the serial console.

You can find additional informations, tutorials and a very comprehensive documentation on http://www.acmesystems.it/arietta.

Build instructions
=============

To build an image for the Arietta G25 choose the configuration corresponding to the Arietta variant.

For 128MB RAM variant type:

$ make acmesystems_arietta_g25_128mb_defconfig

else for 256MB RAM variant type:

$ make acmesystems_arietta_g25_256mb_defconfig

To customize the configuration chosen type:

$ make menuconfig

When you are ready to start building Buildroot type:

$ make

How to write the microSD card
======================

Once the build process is finished you will have an image called "sdcard.img"
in the output/images/ directory.

Copy the bootable "sdcard.img" onto an SD card with "dd":

  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
Quoted 9 lines
Quoted 6 lines

Insert the microSD card into the Arietta slot and power it.

The image just built is fairly basic and the only output you will get is on serial console, please consider to use a DPI cable (http://www.acmesystems.it/DPI)

If for you it's OK, I will include it in the patch for Arietta.

For me it's ok!

Sincerely, Angelo

Quoted 361 lines

Best regards,
Biagio.

2016-09-22 16:18 GMT+02:00 Angelo Compagnucci <
angelo.compagnucci at gmail.com>:

Quoted 352 lines

Hi Biagio,

2016-09-22 16:06 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 9 lines

Hi Angelo,
for that patch I have used "Patches for Arietta G25 board based on Buildroot 2016.08" as title because it adds changes to different files and not only to the default configuration files of Arietta. Notice that I have listed the files modified and a summary of changes made to the relative files including the configuration files for Arietta; anyway I will send a new patch for Arietta with the title suggested by you (configs/acmesystems_arietta_g25: updated kernel and at91bootstrap3)

The general rule is to be atomic in patch subject and content, in your case is more than normal that upgrading a configuration involves touching also board files.

Quoted 4 lines

I will also include your suggestions for the readme.txt file in the new patch. Can I use the name "Arietta" instead of "arietta" in the readme.txt file ?

Yes, sure!

Sincerely, Angelo

Quoted 318 lines

Best regards.
Biagio

2016-09-22 12:14 GMT+02:00 Angelo Compagnucci <
angelo.compagnucci at gmail.com>:

Quoted 309 lines

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 11 lines

- configs/acmesystems_arietta_g25_128mb_defconfig, configs/acmesystems_arietta_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

- board/acmesystems/arietta-g25/genimage.cfg board/acmesystems/arietta-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/arietta-g25/readme.txt : update documentation for Arietta G25 and add notes about how to build sdcard.img

As stated by Thomas in a previous review this patch should have a subject like:

configs/acmesystems_arietta_g25: updated kernel ad at91bootstrap

You should do the same for the Aria patch.

Quoted 82 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 board/acmesystems/arietta-g25/genimage.cfg      | 12 ++++-----
 board/acmesystems/arietta-g25/post-image.sh     |  4 +--
 board/acmesystems/arietta-g25/readme.txt        | 33
++++++++++-------------
 configs/acmesystems_arietta_g25_128mb_defconfig | 36
++++++++++++++-----------
 configs/acmesystems_arietta_g25_256mb_defconfig | 36
++++++++++++++-----------
 5 files changed, 63 insertions(+), 58 deletions(-)
board/acmesystems/arietta-g25/genimage.cfg +6 -8
index 1080b0e..420f1b6 100644
@@ -1,18 +1,18 @@
 # Minimal SD card image for the Acmesystems Arietta G25
-#
+
 image boot.vfat {
        vfat {
                file zImage {
                        image = "zImage"
                }
-
+
                file acme-arietta.dtb {
-                       image = "at91-ariag25.dtb"
+                       image = "at91-ariettag25.dtb"
                }
-
+
                file boot.bin {
-                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.7.bin"
-               }
+                       image = "at91sam9x5_arietta-sdcardboot
-linux-zimage-dt-3.8.6.bin"
+               }
        }
        size = 16M
 }
board/acmesystems/arietta-g25/post-image.sh +1 -3
index c82b189..2846f56 100755
@@ -6,11 +6,9 @@ GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
 
 rm -rf "${GENIMAGE_TMP}"
 
-genimage                               \
+genimage  \
        --rootpath "${TARGET_DIR}"     \
        --tmppath "${GENIMAGE_TMP}"    \
        --inputpath "${BINARIES_DIR}"  \
        --outputpath "${BINARIES_DIR}" \
        --config "${GENIMAGE_CFG}"
-
-exit $?
board/acmesystems/arietta-g25/readme.txt +0 -6
index 485e275..1899ca2 100644
@@ -1,20 +1,10 @@
-Acmesystems Arietta G25
-
-Intro
-=====
-
-This default configuration will allow you to start experimenting with

the
-buildroot environment for the Arietta G25. With the current configuration
-it will bring-up the board, and allow access through the serial console.

board/acmesystems/arietta-g25/readme.txt +0 -2
-
-You can find additional informations, tutorials and a very
Quoted 3 lines

comprehensive
-documentation on http://www.acmesystems.it/arietta.

Why remove this paragraph?

Quoted 13 lines
board/acmesystems/arietta-g25/readme.txt +3 -2
+Acme Systems Arietta G25
 
 Build instructions
 ==================
 
-To build an image for the arietta g25 choose the configuration
-corresponding to the arietta variant.
+To build an image for the Arietta G25 choose the configuration
+corresponding to the Arietta variant.
 
 For 128MB RAM variant type:

board/acmesystems/arietta-g25/readme.txt else for 256MB RAM variant type: · line 18

Quoted 6 lines
board/acmesystems/arietta-g25/readme.txt +1 -1
@@ -24,7 +14,11 @@ else for 256MB RAM variant type:
 
 $ make acmesystems_arietta_g25_256mb_defconfig
 
-then:
+To customize the configuration chosen type:

Typo: chosen not choosed

Quoted 25 lines
board/acmesystems/arietta-g25/readme.txt +4 -0
+
+$ make menuconfig
+
+When you are ready to start building Buildroot type:
 
 $ make

@@ -34,12 +28,13 @@ How to write the microSD card
 Once the build process is finished you will have an image called

"sdcard.img"
in the output/images/ directory.

board/acmesystems/arietta-g25/readme.txt +1 -1
-Copy the bootable "sdcard.img" onto an SD card with "dd":
+Write the bootable SD card image "sdcard.img" onto an SD card with

"dd" command:

   $ sudo dd if=output/images/sdcard.img of=/dev/sdX
board/acmesystems/arietta-g25/readme.txt +3 -1
-Insert the microSD card into the arietta slot and power it.
+Insert the microSD card into the Arietta slot and power it.
+
+To get the kernel log messages you can use a DPI cable (

http://www.acmesystems.it/DPI)

board/acmesystems/arietta-g25/readme.txt How to write the microSD card · line 45

Quoted 3 lines
board/acmesystems/arietta-g25/readme.txt +0 -3
-The image just built is fairly basic and the only output
-you will get is on serial console, please consider to use a DPI
-cable (http://www.acmesystems.it/DPI)

I prefer this paragraph to the one you proposed ;)

Quoted 130 lines

+You can find additional informations, tutorials and a very comprehensive

board/acmesystems/arietta-g25/readme.txt +1 -0
+documentation on http://www.acmesystems.it/arietta.
configs/acmesystems_arietta_g25_128mb_defconfig +7 -3
index e5ddf13..a68ac57 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_128mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-128m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_128mb_defconfig +2 -4
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
configs/acmesystems_arietta_g25_256mb_defconfig +7 -3
index cf6f67b..ce9ebac 100644
@@ -1,30 +1,36 @@
 # Architecture
 BR2_arm=y
 
-# Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Kernel headers
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7=y
 
-# Kernel
+# System configuration
+BR2_TARGET_GENERIC_ISSUE="Welcome to Arietta-G25 Buildroot"
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"
+BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +10 -5
+
+# Kernel configuration
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.1"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.7.4"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariag25"
-BR2_LINUX_KERNEL_XZ=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-ariettag25"
+
+# Root filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
 
-# Bootloader
+# AT91bootstrap bootloader
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c

om/tanzilli/at91bootstrap.git" -BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="cedbde4b3669 5b715f469f4872f47e5cc8115000" +BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.c om/linux4sam/at91bootstrap.git"

configs/acmesystems_arietta_g25_256mb_defconfig +1 -2
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.6"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="arietta-256m"
 
-# Image
-BR2_ROOTFS_POST_IMAGE_SCRIPT="board/acmesystems/arietta-g25

/post-image.sh"

configs/acmesystems_arietta_g25_256mb_defconfig +2 -5
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_PACKAGE_HOST_GENIMAGE=y
+# Tools to build sdcard.img
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
 BR2_PACKAGE_HOST_MTOOLS=y
--

2.7.4

Quoted 5 lines

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

--
Profile: http://it.linkedin.com/in/compagnucciangelo

--
Profile: http://it.linkedin.com/in/compagnucciangelo

Signature · 4 lines
Profile: http://it.linkedin.com/in/compagnucciangelo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/77a6b9b1/attachment.html>
author
#7 lore raw

PATCH 3/3 Patches to update at91bootstrap3 package to 3.8.6 version

In reply to Biagio Montaruli

- boot/at91bootstrap3/Config.in :
add support for the latest version (3.8.6) of AT91bootstrap

- boot/at91bootstrap3/at91bootstrap3.hash :
add the hash file of at91bootstrap-3.8.6.tar.gz

Signed-off-by Biagio Montaruli <[email protected]>
---
 boot/at91bootstrap3/Config.in           | 4 ++--
 boot/at91bootstrap3/at91bootstrap3.hash | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)
boot/at91bootstrap3/Config.in +2 -2
index b8ebe80..237deb9 100644
@@ -15,7 +15,7 @@ choice
 	prompt "AT91 Bootstrap 3 version"
 
 config BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
-	bool "3.8"
+	bool "3.8.6"
 
 config BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT
 	bool "Custom Git repository"

@@ -40,7 +40,7 @@ endif
 
 config BR2_TARGET_AT91BOOTSTRAP3_VERSION
 	string
-	default "v3.8" if BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
+	default "v3.8.6" if BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
 	default BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION \
 		if BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT
boot/at91bootstrap3/at91bootstrap3.hash +1 -1
index eee6482..a3389b7 100644
@@ -1,2 +1,2 @@
 # Locally calculated
-sha256	ae7bb3f8e631f5216f05fd4650b37f2e76d88d0b893bd680f4f398f33b8f3470  at91bootstrap3-v3.8.tar.gz
+sha256	a2e9ec6f42ee3b5a805fe215257b63070b6c498d57c568c46fcb18fd1b38ea7e  at91bootstrap-3.8.6.tar.gz
Signature · 1 line
2.7.4
#8 lore raw

PATCH 3/3 Patches to update at91bootstrap3 package to 3.8.6 version

Hi Biagio,

2016-09-22 11:50 GMT+02:00 Biagio Montaruli <[email protected]>:

Quoted 6 lines

- boot/at91bootstrap3/Config.in :
add support for the latest version (3.8.6) of AT91bootstrap

- boot/at91bootstrap3/at91bootstrap3.hash :
add the hash file of at91bootstrap-3.8.6.tar.gz

This patch should have a subject like:

boot/at91bootstrap3: bump to version 3.8.6

Quoted 48 lines
Signed-off-by Biagio Montaruli <[email protected]>
---
 boot/at91bootstrap3/Config.in           | 4 ++--
 boot/at91bootstrap3/at91bootstrap3.hash | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)
boot/at91bootstrap3/Config.in +2 -2
index b8ebe80..237deb9 100644
@@ -15,7 +15,7 @@ choice
        prompt "AT91 Bootstrap 3 version"
 
 config BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
-       bool "3.8"
+       bool "3.8.6"
 
 config BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT
        bool "Custom Git repository"

@@ -40,7 +40,7 @@ endif
 
 config BR2_TARGET_AT91BOOTSTRAP3_VERSION
        string
-       default "v3.8" if BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
+       default "v3.8.6" if BR2_TARGET_AT91BOOTSTRAP3_LATEST_VERSION
        default BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION \
                if BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT
boot/at91bootstrap3/at91bootstrap3.hash +0 -1
index eee6482..a3389b7 100644
@@ -1,2 +1,2 @@
 # Locally calculated
-sha256 ae7bb3f8e631f5216f05fd4650b37f2e76d88d0b893bd680f4f398f33b8f3470

at91bootstrap3-v3.8.tar.gz
+sha256 a2e9ec6f42ee3b5a805fe215257b63070b6c498d57c568c46fcb18fd1b38ea7e at91bootstrap-3.8.6.tar.gz
--
2.7.4

_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot

Signature · 4 lines
Profile: http://it.linkedin.com/in/compagnucciangelo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/dfb83b35/attachment.html>
#9 lore raw

PATCH 3/3 Patches to update at91bootstrap3 package to 3.8.6 version

In reply to Biagio Montaruli

Hello,

boot/at91bootstrap3/at91bootstrap3.hash line 2

Quoted 2 lines · Biagio Montaruli
boot/at91bootstrap3/at91bootstrap3.hash +1 -1
-sha256	ae7bb3f8e631f5216f05fd4650b37f2e76d88d0b893bd680f4f398f33b8f3470  at91bootstrap3-v3.8.tar.gz
+sha256	a2e9ec6f42ee3b5a805fe215257b63070b6c498d57c568c46fcb18fd1b38ea7e  at91bootstrap-3.8.6.tar.gz

Filename should be:

	at91bootstrap3-v3.8.6.tar.gz

since we're not yet checking hashes for Git-fetched packages you didn't see the difference.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
author
#10 lore raw

PATCH 3/3 Patches to update at91bootstrap3 package to 3.8.6 version

Hello,
I have send the new patch for at91bootstrap3 package to Buildroot mailing list.
Thanks for your help.

2016-09-22 12:25 GMT+02:00 Thomas Petazzoni <
[email protected]>:

Quoted 13 lines

Hello,

Quoted 1 line · Biagio Montaruli

-sha256 ae7bb3f8e631f5216f05fd4650b37f

2e76d88d0b893bd680f4f398f33b8f3470 at91bootstrap3-v3.8.tar.gz

Quoted 1 line

+sha256 a2e9ec6f42ee3b5a805fe215257b63

070b6c498d57c568c46fcb18fd1b38ea7e at91bootstrap-3.8.6.tar.gz

Filename should be:

        at91bootstrap3-v3.8.6.tar.gz
Quoted 9 lines

since we're not yet checking hashes for Git-fetched packages you didn't see the difference.

Thomas
--
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160922/7f686651/attachment.html>

#11 lore raw

PATCH 1/3 Patches for Aria G25 board based on Buildroot 2016.08

In reply to Biagio Montaruli

Hello,

Quoted 4 lines · Biagio Montaruli

- configs/acmesystems_aria_g25_128mb_defconfig, configs/acmesystems_aria_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version

Quoted 8 lines

- board/acmesystems/aria-g25/genimage.cfg board/acmesystems/aria-g25/post-image.sh :
add support for genimage in order to build sdcard.img

- board/acmesystems/aria-g25/readme.txt : update documentation for Aria G25 and add notes about how to build sdcard.img

Signed-off-by Biagio Montaruli <[email protected]>

Applied after fixing the commit title and rewrapping the text in the readme.txt file.

Do you want to be notified for future changes, or build problems related to this configuration? If so, can you please send a patch modifying the DEVELOPERS file, like this:

N: Your name <youremail>
F: board/acmesystems/<name of the board>
F: configs/<name of the defconfig>

Thanks!

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com