Skip to contentSkip to conversation

common/Kconfig: remove NOR_BOOT's depends on NOR

PATCH New Zhiqiang Hou 5 participants 14 messages Oct 12, 2016 – Jan 5, 2017 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

PATCH 1/5 common/Kconfig: remove NOR_BOOT's depends on NOR

From: Hou Zhiqiang <[email protected]>

Remove this dependency to make the NOR_BOOT available for other SoCs which do not have the config NOR, not only for am335x.

---
 common/Kconfig | 1 -
 1 file changed, 1 deletion(-)
common/Kconfig +0 -1
index c69c141..7fd6c49 100644
@@ -101,7 +101,6 @@ menu "Boot media"
 
 config NOR_BOOT
 	bool "Support for booting from NOR flash"
-	depends on NOR
 	help
 	  Enabling this will make a U-Boot binary that is capable of being
 	  booted via NOR.  In this case we will enable certain pinmux early
Signature · 1 line
2.1.0.27.g96db324
#1 lore raw

PATCH 2/5 configs/ls104xa: enable the config NOR_BOOT

From: Hou Zhiqiang <[email protected]>

Enable the config NOR_BOOT obviously for NOR boot defconfigs of ls1043a and ls1046a.

---
 configs/ls1043aqds_defconfig             | 1 +
 configs/ls1043aqds_lpuart_defconfig      | 1 +
 configs/ls1043aqds_nor_ddr3_defconfig    | 1 +
 configs/ls1043ardb_SECURE_BOOT_defconfig | 1 +
 configs/ls1043ardb_defconfig             | 1 +
 configs/ls1046aqds_defconfig             | 1 +
 6 files changed, 6 insertions(+)
configs/ls1043aqds_defconfig +1 -0
index 9352d82..3c8ae2e 100644
@@ -5,6 +5,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_FSL_DDR4=y
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
configs/ls1043aqds_lpuart_defconfig +1 -0
index d384985..8acf732 100644
@@ -6,6 +6,7 @@ CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="LPUART"
 CONFIG_SYS_FSL_DDR4=y
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
configs/ls1043aqds_nor_ddr3_defconfig +1 -0
index 1103346..9be3b2c 100644
@@ -4,6 +4,7 @@ CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
 CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
configs/ls1043ardb_SECURE_BOOT_defconfig +1 -0
index 262769d..0848d66 100644
@@ -6,6 +6,7 @@ CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="SECURE_BOOT"
 CONFIG_SYS_FSL_DDR4=y
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_MMC=y
configs/ls1043ardb_defconfig +1 -0
index e1b75ac..3b6de1d 100644
@@ -5,6 +5,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_FSL_DDR4=y
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_MMC=y
configs/ls1046aqds_defconfig +1 -0
index 71c3b95..d97ddd9 100644
@@ -6,6 +6,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_NOR_BOOT=y
 CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
Signature · 1 line
2.1.0.27.g96db324
#2 lore raw

PATCH 2/5 configs/ls104xa: enable the config NOR_BOOT

Quoted 14 lines

-----Original Message-----
From: Zhiqiang Hou [mailto:Zhiqiang.Hou at nxp.com]
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [PATCH 2/5] configs/ls104xa: enable the config NOR_BOOT

Quoted 5 lines

From: Hou Zhiqiang <[email protected]>

Enable the config NOR_BOOT obviously for NOR boot defconfigs of ls1043a and ls1046a.

Earlier, no CONFIG for NOR boot was required. Why new variable CONFIG_NOR_BOOT is even required?

--prabhakar

author
#3 lore raw

PATCH 2/5 configs/ls104xa: enable the config NOR_BOOT

Hi Prabhakar,

Thanks for your comments!

Quoted 29 lines

-----Original Message-----
From: Prabhakar Kushwaha
Sent: 2016?10?17? 11:40
To: Z.Q. Hou <[email protected]>; u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>;
sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: RE: [PATCH 2/5] configs/ls104xa: enable the config NOR_BOOT

Quoted 5 lines

-----Original Message-----
From: Zhiqiang Hou [mailto:Zhiqiang.Hou at nxp.com]
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com;

hs at denx.de;

Quoted 1 line

yamada.masahiro at socionext.com; Ruchika Gupta

<[email protected]>;

Quoted 7 lines

eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [PATCH 2/5] configs/ls104xa: enable the config NOR_BOOT

Quoted 8 lines
Quoted 5 lines

From: Hou Zhiqiang <[email protected]>

Enable the config NOR_BOOT obviously for NOR boot defconfigs of ls1043a and ls1046a.

Earlier, no CONFIG for NOR boot was required. Why new variable CONFIG_NOR_BOOT is even required?

Now that the Boot Media configs has been introduced, it's reasonable to uniform all boot methods under this framework. And therefore the other config entry is able to be configured according to different Boot Media.

Thanks,
Zhiqiang

#4 lore raw

PATCH 2/5 configs/ls104xa: enable the config NOR_BOOT

Quoted 39 lines · Z.Q. Hou

Hi Prabhakar,

Thanks for your comments!

Quoted 35 lines

-----Original Message-----
From: Prabhakar Kushwaha
Sent: 2016?10?17? 11:40
To: Z.Q. Hou <[email protected]>; u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>;
sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: RE: [PATCH 2/5] configs/ls104xa: enable the config NOR_BOOT

Quoted 5 lines

-----Original Message-----
From: Zhiqiang Hou [mailto:Zhiqiang.Hou at nxp.com]
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com;

hs at denx.de;

Quoted 1 line

yamada.masahiro at socionext.com; Ruchika Gupta

<[email protected]>;

Quoted 12 lines

eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [PATCH 2/5] configs/ls104xa: enable the config NOR_BOOT

From: Hou Zhiqiang <[email protected]>

Enable the config NOR_BOOT obviously for NOR boot defconfigs of ls1043a and ls1046a.

Quoted 5 lines
Quoted 2 lines

Earlier, no CONFIG for NOR boot was required. Why new variable CONFIG_NOR_BOOT is even required?

Now that the Boot Media configs has been introduced, it's reasonable to uniform all boot methods under this framework. And therefore the other config entry is able to be configured according to different Boot Media.

But we also don't want to make this needlessly complicated. The general intention here is that we have some boot methods that are incompatible with others. For example, if a board lacks NOR and we try and run a binary that expects NOR, we panic today. So for beaglebone (where there is a NOR cape that you can boot from) we need a special build that does know about NOR.

At some level, once we have enough things in DM some of this special casing can go away I hope.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161017/6dcab136/attachment.sig>
#5 lore raw

PATCH 3/5 kconfig: armv8: move armv8 sec_firmware CONFIG_* to Kconfig

In reply to Zhiqiang Hou

From: Hou Zhiqiang <[email protected]>

---
 arch/arm/cpu/armv8/Kconfig            | 36 +++++++++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/Makefile           |  2 +-
 arch/arm/cpu/armv8/sec_firmware_asm.S |  4 ++--
 include/configs/ls1043ardb.h          |  4 ----
 include/configs/ls1046ardb.h          |  4 ----
 5 files changed, 39 insertions(+), 11 deletions(-)
arch/arm/cpu/armv8/Kconfig +36 -0
index 7e1fc4c..cb5a970 100644
@@ -21,4 +21,40 @@ config ARMV8_SPIN_TABLE
 	    - Reserve the code for the spin-table and the release address
 	      via a /memreserve/ region in the Device Tree.
 
+menu "ARMv8 secure monitor firmware"
+config ARMV8_SEC_FIRMWARE_SUPPORT
+	bool "Enable ARMv8 secure monitor firmware framework support"
+	select OF_LIBFDT
+	select FIT
+	help
+	  This framework is aimed at making secure monitor firmware load
+	  process brief.
+	  Note: Only FIT format image is supported.
+	  You should prepare and provide the below information:
+	    - Address of secure firmware.
+	    - Address to hold the return address from secure firmware.
+	    - Secure firmware FIT image related information.
+	      Such as: SEC_FIRMWARE_FIT_IMAGE and SEC_FIRMEWARE_FIT_CNF_NAME
+	    - The target exception level that secure monitor firmware will
+	      return to.
+
+config SPL_ARMV8_SEC_FIRMWARE_SUPPORT
+	bool "Enable ARMv8 secure monitor firmware framework support for SPL"
+	select SPL_OF_LIBFDT
+	select SPL_FIT
+	help
+	  Say Y here to support this framework in SPL phase.
+
+config ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT
+	bool "ARMv8 secure monitor firmware ERET address byteorder swap"
+	depends on ARMV8_SEC_FIRMWARE_SUPPORT || SPL_ARMV8_SEC_FIRMWARE_SUPPORT
+	help
+	  Say Y here when the endianness of the register or memory holding the
+	  Secure firmware exception return address is different with core's.
+
+endmenu
+
+config ARMV8_PSCI
+	bool "ARMv8 PSCI support"
+
 endif
arch/arm/cpu/armv8/Makefile +1 -1
index dea1465..9f65927 100644
@@ -19,7 +19,7 @@ obj-y	+= cpu-dt.o
 ifndef CONFIG_SPL_BUILD
 obj-$(CONFIG_ARMV8_SPIN_TABLE) += spin_table.o spin_table_v8.o
 endif
-obj-$(CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT) += sec_firmware.o sec_firmware_asm.o
+obj-$(CONFIG_$(SPL_)ARMV8_SEC_FIRMWARE_SUPPORT) += sec_firmware.o sec_firmware_asm.o
 
 obj-$(CONFIG_FSL_LAYERSCAPE) += fsl-layerscape/
 obj-$(CONFIG_S32V234) += s32v234/
arch/arm/cpu/armv8/sec_firmware_asm.S +2 -2
index 0c6a462..15fbe0b 100644
@@ -23,12 +23,12 @@ WEAK(_sec_firmware_entry)
 	/* Set exception return address hold pointer */
         adr	x4, 1f
         mov	x3, x4
-#ifdef SEC_FIRMWARE_ERET_ADDR_REVERT
+#ifdef CONFIG_ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT
         rev	w3, w3
 #endif
         str	w3, [x1]
         lsr	x3, x4, #32
-#ifdef SEC_FIRMWARE_ERET_ADDR_REVERT
+#ifdef CONFIG_ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT
         rev	w3, w3
 #endif
         str	w3, [x2]
include/configs/ls1043ardb.h +0 -4
index 70ee046..4b4d090 100644
@@ -10,10 +10,6 @@
 #include "ls1043a_common.h"
 
 #if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
-#define SEC_FIRMWARE_ERET_ADDR_REVERT
-#define CONFIG_ARMV8_PSCI
-
 #define CONFIG_SYS_LS_PPA_FW_IN_XIP
 #ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
 #define	CONFIG_SYS_LS_PPA_FW_ADDR	0x60500000
include/configs/ls1046ardb.h +0 -4
index 693cc8d..85a58b0 100644
@@ -10,10 +10,6 @@
 #include "ls1046a_common.h"
 
 #if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_ARMV8_PSCI
-#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
-#define CONFIG_SYS_LS_PPA_DRAM_BLOCK_MIN_SIZE		(1UL * 1024 * 1024)
-
 #define CONFIG_SYS_LS_PPA_FW_IN_XIP
 #ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
 #define	CONFIG_SYS_LS_PPA_FW_ADDR	0x40500000
Signature · 1 line
2.1.0.27.g96db324
#6 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

In reply to Zhiqiang Hou

From: Hou Zhiqiang <[email protected]>

---
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig  | 29 +++++++++++++++++++++++++++++
 arch/arm/cpu/armv8/fsl-layerscape/Makefile |  2 +-
 include/configs/ls1043ardb.h               |  7 -------
 include/configs/ls1046ardb.h               |  7 -------
 4 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +29 -0
index 94ec8d5..952db19 100644
@@ -44,6 +44,35 @@ config FSL_LSCH3
 menu "Layerscape architecture"
 	depends on FSL_LSCH2 || FSL_LSCH3
 
+menu "Layerscape PPA"
+config FSL_LS_PPA
+	bool "FSL Layerscape PPA firmware support"
+	depends on ARCH_LS1043A || ARCH_LS1046A
+	select ARMV8_PSCI
+	select ARMV8_SEC_FIRMWARE_SUPPORT
+	select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT
+	help
+	  The FSL Primary Protected Application (PPA) is a software component
+	  loaded during boot which runs in TrustZone and remains resident
+	  after boot.
+choice
+	prompt "FSL Layerscape PPA firmware storage select"
+	depends on FSL_LS_PPA
+	default SYS_LS_PPA_FW_IN_XIP
+
+config SYS_LS_PPA_FW_IN_XIP
+	bool "XIP"
+
+endchoice
+
+config SYS_LS_PPA_FW_ADDR
+	hex "Address of PPA firmware"
+	depends on FSL_LS_PPA
+	default 0x60500000 if SYS_LS_PPA_FW_IN_XIP && NOR_BOOT
+	default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
+
+endmenu
+
 config SYS_FSL_MMDC
 	bool
 
arch/arm/cpu/armv8/fsl-layerscape/Makefile +1 -1
index 51c1cee..150eb7a 100644
@@ -10,7 +10,7 @@ obj-y += soc.o
 obj-$(CONFIG_MP) += mp.o
 obj-$(CONFIG_OF_LIBFDT) += fdt.o
 obj-$(CONFIG_SPL) += spl.o
-obj-$(CONFIG_FSL_LS_PPA) += ppa.o
+obj-$(CONFIG_$(SPL_)FSL_LS_PPA) += ppa.o
 
 ifneq ($(CONFIG_FSL_LSCH3),)
 obj-y += fsl_lsch3_speed.o
include/configs/ls1043ardb.h +0 -7
index 4b4d090..3023c48 100644
@@ -9,13 +9,6 @@
 
 #include "ls1043a_common.h"
 
-#if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_SYS_LS_PPA_FW_IN_XIP
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
-#define	CONFIG_SYS_LS_PPA_FW_ADDR	0x60500000
-#endif
-#endif
-
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
include/configs/ls1046ardb.h +0 -7
index 85a58b0..3ea02f0 100644
@@ -9,13 +9,6 @@
 
 #include "ls1046a_common.h"
 
-#if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_SYS_LS_PPA_FW_IN_XIP
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
-#define	CONFIG_SYS_LS_PPA_FW_ADDR	0x40500000
-#endif
-#endif
-
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
Signature · 1 line
2.1.0.27.g96db324
#7 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

Quoted 34 lines

-----Original Message-----
From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Zhiqiang Hou
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [U-Boot] [PATCH 4/5] kconfig: fsl PPA: move CONFIG_* to Kconfig

From: Hou Zhiqiang <[email protected]>

---
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig  | 29
+++++++++++++++++++++++++++++  arch/arm/cpu/armv8/fsl-
layerscape/Makefile |  2 +-
 include/configs/ls1043ardb.h               |  7 -------
 include/configs/ls1046ardb.h               |  7 -------
 4 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +0 -0
index 94ec8d5..952db19 100644

arch/arm/cpu/armv8/fsl-layerscape/Kconfig config FSL_LSCH3 · line 53

Quoted 10 lines
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +7 -0
@@ -44,6 +44,35 @@ config FSL_LSCH3
 menu "Layerscape architecture"
 	depends on FSL_LSCH2 || FSL_LSCH3
 
+menu "Layerscape PPA"
+config FSL_LS_PPA
+	bool "FSL Layerscape PPA firmware support"
+	depends on ARCH_LS1043A || ARCH_LS1046A
+	select ARMV8_PSCI
+	select ARMV8_SEC_FIRMWARE_SUPPORT
+	select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT

' ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT' macro is not required for chassis 3 platforms like LS2088A. So there should be separate CONFIG_.. option for this.

Quoted 83 lines
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +2 -0
+	help
+	  The FSL Primary Protected Application (PPA) is a software

component

arch/arm/cpu/armv8/fsl-layerscape/Kconfig +20 -0
+	  loaded during boot which runs in TrustZone and remains resident
+	  after boot.
+choice
+	prompt "FSL Layerscape PPA firmware storage select"
+	depends on FSL_LS_PPA
+	default SYS_LS_PPA_FW_IN_XIP
+
+config SYS_LS_PPA_FW_IN_XIP
+	bool "XIP"
+
+endchoice
+
+config SYS_LS_PPA_FW_ADDR
+	hex "Address of PPA firmware"
+	depends on FSL_LS_PPA
+	default 0x60500000 if SYS_LS_PPA_FW_IN_XIP && NOR_BOOT
+	default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
+
+endmenu
+
 config SYS_FSL_MMDC
 	bool
arch/arm/cpu/armv8/fsl-layerscape/Makefile +1 -1
index 51c1cee..150eb7a 100644
@@ -10,7 +10,7 @@ obj-y += soc.o
 obj-$(CONFIG_MP) += mp.o
 obj-$(CONFIG_OF_LIBFDT) += fdt.o
 obj-$(CONFIG_SPL) += spl.o
-obj-$(CONFIG_FSL_LS_PPA) += ppa.o
+obj-$(CONFIG_$(SPL_)FSL_LS_PPA) += ppa.o
 
 ifneq ($(CONFIG_FSL_LSCH3),)
 obj-y += fsl_lsch3_speed.o
include/configs/ls1043ardb.h +0 -7
index 4b4d090..3023c48 100644
@@ -9,13 +9,6 @@
 
 #include "ls1043a_common.h"
 
-#if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_SYS_LS_PPA_FW_IN_XIP
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
-#define	CONFIG_SYS_LS_PPA_FW_ADDR	0x60500000
-#endif
-#endif
-
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
include/configs/ls1046ardb.h +0 -8
index 85a58b0..3ea02f0 100644
@@ -9,13 +9,6 @@
 
 #include "ls1046a_common.h"
 
-#if defined(CONFIG_FSL_LS_PPA)
-#define CONFIG_SYS_LS_PPA_FW_IN_XIP
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
-#define	CONFIG_SYS_LS_PPA_FW_ADDR	0x40500000
-#endif
-#endif
-
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
--

2.1.0.27.g96db324

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#8 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

Quoted 37 lines · Priyanka Jain
Quoted 37 lines

-----Original Message-----
From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Zhiqiang Hou
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [U-Boot] [PATCH 4/5] kconfig: fsl PPA: move CONFIG_* to Kconfig

From: Hou Zhiqiang <[email protected]>

---
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig  | 29
+++++++++++++++++++++++++++++  arch/arm/cpu/armv8/fsl-
layerscape/Makefile |  2 +-
 include/configs/ls1043ardb.h               |  7 -------
 include/configs/ls1046ardb.h               |  7 -------
 4 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +0 -0
index 94ec8d5..952db19 100644
@@ -44,6 +44,35 @@ config FSL_LSCH3
 menu "Layerscape architecture"
 	depends on FSL_LSCH2 || FSL_LSCH3
 
Quoted 9 lines

arch/arm/cpu/armv8/fsl-layerscape/Kconfig config FSL_LSCH3 · line 53

Quoted 7 lines
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +7 -0
+menu "Layerscape PPA"
+config FSL_LS_PPA
+	bool "FSL Layerscape PPA firmware support"
+	depends on ARCH_LS1043A || ARCH_LS1046A
+	select ARMV8_PSCI
+	select ARMV8_SEC_FIRMWARE_SUPPORT
+	select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT

' ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT' macro is not required for chassis 3 platforms like LS2088A. So there should be separate CONFIG_.. option for this.

Zhiqiang,

How will you handle lsch3?

York

author
#9 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

Hi York,

Thanks for your comments!

Quoted 62 lines

-----Original Message-----
From: york sun
Sent: 2016?11?8? 2:33
To: Priyanka Jain <[email protected]>; Z.Q. Hou <[email protected]>; u-boot at lists.denx.de; albert.u.boot at aribaud.net; sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Subject: Re: [U-Boot] [PATCH 4/5] kconfig: fsl PPA: move CONFIG_* to Kconfig

Quoted 8 lines · Priyanka Jain
Quoted 8 lines

-----Original Message-----
From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Zhiqiang Hou
Sent: Wednesday, October 12, 2016 2:56 PM
To: u-boot at lists.denx.de; albert.u.boot at aribaud.net; york sun <[email protected]>; sjg at chromium.org; bmeng.cn at gmail.com;

hs at denx.de;

Quoted 1 line
Quoted 1 line

yamada.masahiro at socionext.com; Ruchika Gupta

<[email protected]>;

Quoted 1 line
Quoted 1 line

eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar

Kushwaha

Quoted 27 lines
Quoted 27 lines

<[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Cc: Z.Q. Hou <[email protected]>
Subject: [U-Boot] [PATCH 4/5] kconfig: fsl PPA: move CONFIG_* to Kconfig

From: Hou Zhiqiang <[email protected]>

---
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig  | 29
+++++++++++++++++++++++++++++  arch/arm/cpu/armv8/fsl-
layerscape/Makefile |  2 +-
 include/configs/ls1043ardb.h               |  7 -------
 include/configs/ls1046ardb.h               |  7 -------
 4 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +0 -0
index 94ec8d5..952db19 100644
@@ -44,6 +44,35 @@ config FSL_LSCH3
 menu "Layerscape architecture"
 	depends on FSL_LSCH2 || FSL_LSCH3
 
Quoted 8 lines

arch/arm/cpu/armv8/fsl-layerscape/Kconfig config FSL_LSCH3 · line 53

Quoted 7 lines
arch/arm/cpu/armv8/fsl-layerscape/Kconfig +7 -0
+menu "Layerscape PPA"
+config FSL_LS_PPA
+	bool "FSL Layerscape PPA firmware support"
+	depends on ARCH_LS1043A || ARCH_LS1046A
+	select ARMV8_PSCI
+	select ARMV8_SEC_FIRMWARE_SUPPORT
+	select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT

' ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT' macro is not required for

Quoted 7 lines

chassis 3 platforms like LS2088A.

Quoted 1 line

So there should be separate CONFIG_.. option for this.

Zhiqiang,

How will you handle lsch3?

Will change it to 'select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT if FSL_LSCH2', since SCFG is big-endian on FSL_LSCH2 but little-endian on FSL_LSCH3.

Thanks,
Zhiqiang

#10 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

Quoted 6 lines · Z.Q. Hou
Quoted 4 lines

Zhiqiang,

How will you handle lsch3?

Will change it to 'select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT if FSL_LSCH2', since SCFG is big-endian on FSL_LSCH2 but little-endian on FSL_LSCH3.

Zhiqiang,

Have you sent out an update? If not, please rebase your code before sending it.

York

author
#11 lore raw

PATCH 4/5 kconfig: fsl PPA: move CONFIG_* to Kconfig

Hi York,

Thanks for your comments!

Quoted 19 lines

-----Original Message-----
From: york sun
Sent: 2017?1?5? 2:49
To: Z.Q. Hou <[email protected]>; Priyanka Jain <[email protected]>; u-boot at lists.denx.de; albert.u.boot at aribaud.net; sjg at chromium.org; bmeng.cn at gmail.com; hs at denx.de; yamada.masahiro at socionext.com; Ruchika Gupta <[email protected]>; eddy.petrisor at gmail.com; s.temerkhanov at gmail.com; Prabhakar Kushwaha <[email protected]>; sr at denx.de; van.freenix at gmail.com; fgretief at spaceteq.co.za; rpjday at crashcourse.ca; trini at konsulko.com; Mingkai Hu <[email protected]>
Subject: Re: [U-Boot] [PATCH 4/5] kconfig: fsl PPA: move CONFIG_* to Kconfig

Quoted 5 lines · Z.Q. Hou
Quoted 4 lines

Zhiqiang,

How will you handle lsch3?

Will change it to 'select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT if

Quoted 8 lines

FSL_LSCH2', since SCFG is big-endian on FSL_LSCH2 but little-endian on FSL_LSCH3.

Quoted 1 line

Zhiqiang,

Have you sent out an update? If not, please rebase your code before sending it.

No, I haven't. This task has not been arranged to this sprint, will add it to next sprint.

Thanks,
Zhiqiang

#12 lore raw

PATCH 5/5 fsl PPA: enable PPA for ls1043ardb and ls1046ardb

In reply to Zhiqiang Hou

From: Hou Zhiqiang <[email protected]>

Enable PPA for ls1043ardb NOR boot and ls1046ardb QSPI boot.

---
 configs/ls1043ardb_defconfig      | 1 +
 configs/ls1046ardb_qspi_defconfig | 1 +
 2 files changed, 2 insertions(+)
configs/ls1043ardb_defconfig +1 -0
index 3b6de1d..70e0c36 100644
@@ -3,6 +3,7 @@ CONFIG_TARGET_LS1043ARDB=y
 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
 CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
+CONFIG_FSL_LS_PPA=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_FSL_DDR4=y
 CONFIG_NOR_BOOT=y
configs/ls1046ardb_qspi_defconfig +1 -0
index 67ef3ce..56b39c5 100644
@@ -4,6 +4,7 @@ CONFIG_DM_SPI=y
 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
 CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
+CONFIG_FSL_LS_PPA=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
 CONFIG_QSPI_BOOT=y
Signature · 1 line
2.1.0.27.g96db324
#13 lore raw

PATCH 1/5 common/Kconfig: remove NOR_BOOT's depends on NOR

In reply to Zhiqiang Hou
Quoted 6 lines · Zhiqiang Hou

From: Hou Zhiqiang <[email protected]>

Remove this dependency to make the NOR_BOOT available for other SoCs which do not have the config NOR, not only for am335x.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161013/17c0f61f/attachment.sig>