network: test_net.sh: allow to run network tests on a single machine

index dc52d95..f5321d7 100644
@@ -20,6 +20,31 @@
 
 [ -z "$TST_LIB_LOADED" ] && . test.sh
 
+init_ltp_netspace()
+{
+	if [ ! -f /var/run/netns/ltp_ns ]; then
+		ROD ip net add ltp_ns
+		ROD ip li add name ltp_ns_veth1 type veth peer name ltp_ns_veth2
+		ROD ip li set dev ltp_ns_veth1 netns ltp_ns
+	fi
+
+	LHOST_IFACES=${LHOST_IFACES:-"ltp_ns_veth2"}
+	RHOST_IFACES=${RHOST_IFACES:-"ltp_ns_veth1"}
+
+	export TST_INIT_NETNS="no"
+	export LTP_NETNS=${LTP_NETNS:-"ip netns exec ltp_ns"}
+
+	tst_init_iface
+	tst_init_iface rhost
+
+	tst_add_ipaddr
+	tst_add_ipaddr rhost
+
+	TST_IPV6=6 tst_add_ipaddr
+	TST_IPV6=6 tst_add_ipaddr rhost
+
+}
+
 # Run command on remote host.
 # Options:
 # -b run in background

@@ -67,6 +92,9 @@ tst_rhost_run()
 	if [ -n "$TST_USE_SSH" ]; then
 		output=`ssh -n -q $user@$RHOST "sh -c \
 			'$pre_cmd $cmd $post_cmd'" $out 2>&1 || echo 'RTERR'`
+	elif [ -n "$TST_USE_NETNS" ]; then
+		output=`$LTP_NETNS sh -c \
+			"$pre_cmd $cmd $post_cmd" $out 2>&1 || echo 'RTERR'`
 	else
 		output=`rsh -n -l $user $RHOST "sh -c \
 			'$pre_cmd $cmd $post_cmd'" $out 2>&1 || echo 'RTERR'`

@@ -346,22 +374,13 @@ tst_ping()
 }
 
 # Management Link
-[ -z "$RHOST" ] && tst_brkm TBROK "RHOST variable not defined"
+[ -z "$RHOST" ] && TST_USE_NETNS="yes"
 export RHOST="$RHOST"
 export PASSWD=${PASSWD:-""}
 # Don't use it in new tests, use tst_rhost_run() from test_net.sh instead.
 export LTP_RSH=${LTP_RSH:-"rsh -n"}
 
 # Test Links
-# Warning: make sure to set valid interface names and IP addresses below.
-# Set names for test interfaces, e.g. "eth0 eth1"
-export LHOST_IFACES=${LHOST_IFACES:-"eth0"}
-export RHOST_IFACES=${RHOST_IFACES:-"eth0"}
-
-# Set corresponding HW addresses, e.g. "00:00:00:00:00:01 00:00:00:00:00:02"
-export LHOST_HWADDRS=${LHOST_HWADDRS:-"$(tst_get_hwaddrs lhost)"}
-export RHOST_HWADDRS=${RHOST_HWADDRS:-"$(tst_get_hwaddrs rhost)"}
-
 # Set first three octets of the network address, default is '10.0.0'
 export IPV4_NETWORK=${IPV4_NETWORK:-"10.0.0"}
 # Set local host last octet, default is '2'

@@ -408,5 +427,15 @@ export UPLOAD_REGFILESIZE=${UPLOAD_REGFILESIZE:-"1024"}
 export MCASTNUM_NORMAL=${MCASTNUM_NORMAL:-"20"}
 export MCASTNUM_HEAVY=${MCASTNUM_HEAVY:-"40000"}
 
+[ -n "$TST_USE_NETNS" -a "$TST_INIT_NETNS" != "no" ] && init_ltp_netspace
+
+# Warning: make sure to set valid interface names and IP addresses below.
+# Set names for test interfaces, e.g. "eth0 eth1"
+export LHOST_IFACES=${LHOST_IFACES:-"eth0"}
+export RHOST_IFACES=${RHOST_IFACES:-"eth0"}
+# Set corresponding HW addresses, e.g. "00:00:00:00:00:01 00:00:00:00:00:02"
+export LHOST_HWADDRS=${LHOST_HWADDRS:-"$(tst_get_hwaddrs lhost)"}
+export RHOST_HWADDRS=${RHOST_HWADDRS:-"$(tst_get_hwaddrs rhost)"}
+
 # More information about network parameters can be found
 # in the following document: testcases/network/stress/README

81 lines not on this page · raw message