ath10k raw mode
Dear All,
could you please someone send me or let me know where I can download a firmware with raw mode flag enabled for my QCA988X card.
Thanks,
Andreas
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 3 lines · Andreas Christoforou
Dear All,
could you please someone send me or let me know where I can download a firmware with raw mode flag enabled for my QCA988X card.
You can check this:
https://github.com/kvalo/ath10k-firmware/tree/master/QCA988X/hw2.0/10.2.4.70
At the very least 10.2.4.70.54 should support it (at least it does advertise it). It probably makes sense to have this (list of raw-mode supporting firmware revisions) listed somewhere on
https://wireless.wiki.kernel.org/en/users/drivers/ath10k - any volunteers? :)
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
A message that is not in the archive (sent off-list or not yet received): CAPd_300YffoiqezwWx82GuMiSHgC7kg6JCF8KNZ2_ytj=gnfzQ@mail.gmail.com
Quoted 43 lines · Andreas Christoforou
Dear Michal,
unfortunately I am getting the following error
[ 50.416483] ath10k_pci 0000:07:00.0: firmware crashed! (uuid bdf6b230-c8f5-4e61-b174-93b0980ee5dc) [ 50.425506] ath10k_pci 0000:07:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 1 hwcrypto 0 features no-p2p,raw-mode [ 50.444686] ath10k_pci 0000:07:00.0: debug 1 debugfs 1 tracing 1 dfs 0 testmode 1 [ 50.454283] ath10k_pci 0000:07:00.0: firmware register dump: [ 50.460008] ath10k_pci 0000:07:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000 [ 50.467940] ath10k_pci 0000:07:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.475908] ath10k_pci 0000:07:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.483865] ath10k_pci 0000:07:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.491869] ath10k_pci 0000:07:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5 [ 50.499851] ath10k_pci 0000:07:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000 [ 50.507784] ath10k_pci 0000:07:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.515756] ath10k_pci 0000:07:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.523721] ath10k_pci 0000:07:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.531692] ath10k_pci 0000:07:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.539649] ath10k_pci 0000:07:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.547592] ath10k_pci 0000:07:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.555547] ath10k_pci 0000:07:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.563519] ath10k_pci 0000:07:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000 [ 50.571478] ath10k_pci 0000:07:00.0: [56]: 0x00000000 0x00000000
0x000000000x00000000
Quoted 8 lines
[ 50.583360] ath10k_warn: 6 callbacks suppressed [ 50.587916] ath10k_pci 0000:07:00.0: failed to start WMI vdev 0: -108 [ 50.594461] ath10k_pci 0000:07:00.0: failed to start vdev 0 addr 00:00:00:00:00:00 on freq 2412: -108 [ 50.705799] ieee80211 phy0: Hardware restart was requested [ 50.712476] ath10k_pci 0000:07:00.0: failed to flush transmit queue (skip 1 ar-state 2): 500 [ 50.722235] ath10k_pci 0000:07:00.0: failed to delete WMI vdev 0: -108
All I can tell from this is seems to crash when you try to start an interface. Is it a monitor interface? If you intend to inject frames - it's not supported. I'm not sure if anyone tried monitor mode for sniffing with raw-mode enabled.
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k