ARM: imx6: add support for SolidRun Hummingboard2
Subsystems (3)
PATCH 1/1 ARM: imx6: add support for SolidRun Hummingboard2
Aka: Hummingboard Edge and Hummingboard Gate
This currently only supports the pieces I was able to test:
- RTC
- SD card with UHS modes
- eMMC
- SGTL5000 sound
- All standard host USB ports
- mini PCIe
- IR receiver
- HDMI output
Functions routed out to the pin headers are not enabled and have not been tested.
--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-hummingboard2.dts | 50 ++++ arch/arm/boot/dts/imx6q-hummingboard2.dts | 58 +++++ arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi | 372 +++++++++++++++++++++++++++ 4 files changed, 482 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-hummingboard2.dts create mode 100644 arch/arm/boot/dts/imx6q-hummingboard2.dts create mode 100644 arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi
arch/arm/boot/dts/Makefile +2 -0
@@ -348,6 +348,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw552x.dtb \ imx6dl-gw553x.dtb \ imx6dl-hummingboard.dtb \ + imx6dl-hummingboard2.dtb \ imx6dl-icore.dtb \ imx6dl-nit6xlite.dtb \ imx6dl-nitrogen6x.dtb \
@@ -390,6 +391,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw553x.dtb \ imx6q-h100.dtb \ imx6q-hummingboard.dtb \ + imx6q-hummingboard2.dtb \ imx6q-icore.dtb \ imx6q-icore-rqs.dtb \ imx6q-marsboard.dtb \
arch/arm/boot/dts/imx6dl-hummingboard2.dts new file +50 -0
50 lines not on this page · raw message
arch/arm/boot/dts/imx6q-hummingboard2.dts new file +58 -0
58 lines not on this page · raw message
arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi new file +372 -0
372 lines not on this page · raw message
Signature · 1 line
2.9.3
PATCH 1/1 ARM: imx6: add support for SolidRun Hummingboard2
Quoted 12 lines · Lucas Stach
Aka: Hummingboard Edge and Hummingboard Gate
This currently only supports the pieces I was able to test:
- RTC
- SD card with UHS modes
- eMMC
- SGTL5000 sound
- All standard host USB ports
- mini PCIe
- IR receiver
- HDMI output
Quoted 2 lines
Functions routed out to the pin headers are not enabled and have not been tested.
It would be nice if you talked to me or at least Jon, as I'm SolidRun's "official" path to getting support for their boards merged - and rather than having a Lucas special independently created DT file merged, we can have one which closer resembles the one in the SolidRun tree.
I know working with manufacters isn't seen to be a good thing to do in Open Source, but it would really help if people did at least try.
I've been holding off on the HB2 DT patches because there's changes I needed which I need to talk to Jon about before I send them upstream.
You can find the changes in my "hb2" branch.
Signature · 3 lines
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up according to speedtest.net.