spi: ich: Configure SPI BIOS parameters
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Without configuring these registers in the SPI controller, the Linux MTD device driver is not able to correctly read/write to the SPI NOR chip at all. In fact, the chip is not detected at all.
---
v3:
- Moved defines from C-file into header file
- Changed some enum's into macros in ich.h for consistency
- Used these newly introduced defines
v2:
- Moved code into the ICH SPI driver as suggested by Simon and Bin
drivers/spi/ich.c | 18 ++++++++++++++++++ drivers/spi/ich.h | 45 ++++++++++++++++++++++++++++++++++++++------- 2 files changed, 56 insertions(+), 7 deletions(-)
drivers/spi/ich.c +18 -0
@@ -111,6 +111,17 @@ static int ich9_can_do_33mhz(struct udevice *dev)return speed ==1 ; } +/* +* Configure SPI controller so that the Linux MTD driver can fully +* access the SPI NOR chip +*/ +static void spi_controller_config (struct ich_spi_priv *ctlr) +{ +ich_writew (ctlr,SPI_OPTYPE , ctlr->optype); +ich_writel (ctlr,SPI_OPMENU_LOWER , ctlr->opmenu); +ich_writel (ctlr,SPI_OPMENU_UPPER , ctlr->opmenu +sizeof (u32)); +} +static int ich_init_controller (struct udevice *dev,struct ich_spi_platdata *plat,struct ich_spi_priv *ctlr)
@@ -172,6 +183,13 @@ static int ich_init_controller(struct udevice *dev,ich_set_bbar (ctlr,0 ); +/* +* Configure the SPI-NOR controller in a way that the Linux +* MTD SPI-NOR device driver has full read-write access to +* the SPI-NOR chips +*/ +spi_controller_config (ctlr); +return 0 ; }
drivers/spi/ich.h +38 -7
57 lines not on this page · raw message
Signature · 1 line
2.11.1
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Stefan,
Quoted 76 lines · Stefan Roese
Without configuring these registers in the SPI controller, the Linux MTD device driver is not able to correctly read/write to the SPI NOR chip at all. In fact, the chip is not detected at all.
Signed-off-by Stefan Roese <[email protected]>Cc Bin Meng <[email protected]>Cc Simon Glass <[email protected]>Cc Jagan Teki <[email protected]>---
v3:
- Moved defines from C-file into header file
- Changed some enum's into macros inich.hfor consistency
- Used these newly introduced definesv2:
- Moved code into the ICH SPI driver as suggested by Simon and Bindrivers/spi/ich.c | 18 ++++++++++++++++++ drivers/spi/ich.h | 45 ++++++++++++++++++++++++++++++++++++++------- 2 files changed, 56 insertions(+), 7 deletions(-)drivers/spi/ich.c +18
-0@@ -111,6 +111,17 @@ static int ich9_can_do_33mhz(struct udevice *dev)return speed ==1 ; } +/* +* Configure SPI controller so that the Linux MTD driver can fully +* access the SPI NOR chip +*/ +static void spi_controller_config (struct ich_spi_priv *ctlr) +{ +ich_writew (ctlr,SPI_OPTYPE , ctlr->optype); +ich_writel (ctlr,SPI_OPMENU_LOWER , ctlr->opmenu); +ich_writel (ctlr,SPI_OPMENU_UPPER , ctlr->opmenu +sizeof (u32)); +} +static int ich_init_controller (struct udevice *dev,struct ich_spi_platdata *plat,struct ich_spi_priv *ctlr)@@ -172,6 +183,13 @@ static int ich_init_controller(struct udevice *dev,ich_set_bbar (ctlr,0 ); +/* +* Configure the SPI-NOR controller in a way that the Linux +* MTD SPI-NOR device driver has full read-write access to +* the SPI-NOR chips +*/ +spi_controller_config (ctlr); +return 0 ; }drivers/spi/ich.h +0
-7@@ -102,13 +102,6 @@ enum { };enum { -SPI_OPCODE_TYPE_READ_NO_ADDRESS =0 , -SPI_OPCODE_TYPE_WRITE_NO_ADDRESS =1 , -SPI_OPCODE_TYPE_READ_WITH_ADDRESS =2 , -SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS =3 -}; - -enum {ICH_MAX_CMD_LEN =5 , };
drivers/spi/ich.h struct spi_trans { · line 127
Quoted 8 lines
drivers/spi/ich.h +5
-0@@ -127,6 +120,44 @@ struct spi_trans {#define SPI_OPCODE_WREN 0x06#define SPI_OPCODE_FAST_READ 0x0b +#define SPI_OPCODE_TYPE_READ_NO_ADDRESS 0 +#define SPI_OPCODE_TYPE_WRITE_NO_ADDRESS 1 +#define SPI_OPCODE_TYPE_READ_WITH_ADDRESS 2 +#define SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS 3 +
Thanks for changing this.
Quoted 14 lines
drivers/spi/ich.h +14
-0+#define SPI_OPMENU_0 0x01/* WRSR: Write Status Register */ +#define SPI_OPTYPE_0 SPI_OPCODE_TYPE_WRITE_NO_ADDRESS + +#define SPI_OPMENU_1 0x02/* BYPR: Byte Program */ +#define SPI_OPTYPE_1 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_2 0x03/* READ: Read Data */ +#define SPI_OPTYPE_2 SPI_OPCODE_TYPE_READ_WITH_ADDRESS + +#define SPI_OPMENU_3 0x05/* RDSR: Read Status Register */ +#define SPI_OPTYPE_3 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_4 0x20/* SE20: Sector Erase 0x20 */ +#define SPI_OPTYPE_4 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS
drivers/spi/ich.h struct spi_trans { · line 151
Quoted 10 lines
drivers/spi/ich.h +10
-0+ +#define SPI_OPMENU_5 0x9f/* RDID: Read ID */ +#define SPI_OPTYPE_5 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_6 0xd8/* BED8: Block Erase 0xd8 */ +#define SPI_OPTYPE_6 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_7 0x0b/* FAST: Fast Read */ +#define SPI_OPTYPE_7 SPI_OPCODE_TYPE_READ_WITH_ADDRESS +
These are SPI flash commands. Should we name them similarly like SPI_OPCODE_WREN and SPI_OPCODE_FAST_READ?
drivers/spi/ich.h struct spi_trans { · line 160
Quoted 9 lines
drivers/spi/ich.h +9
-0+#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \ + (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) | \ + (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) | \ + (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0 << 0)) +#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \ + (SPI_OPMENU_5 << 8) | (SPI_OPMENU_4 << 0)) +#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \ + (SPI_OPMENU_1 << 8) | (SPI_OPMENU_0 << 0)) +
What if the board mounts a flash with a different SPI flash command set? Will this work?
drivers/spi/ich.h struct spi_trans {
Quoted 4 lines
drivers/spi/ich.h +0
-1enum ich_version {ICHV_7 ,ICHV_9 , --
Regards,
Bin
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Bin,
On 10.02.2017 06:45, Bin Meng wrote:
<snip>
Quoted 31 lines
drivers/spi/ich.h struct spi_trans { · line 127
Quoted 9 lines
drivers/spi/ich.h +5
-0@@ -127,6 +120,44 @@ struct spi_trans {#define SPI_OPCODE_WREN 0x06#define SPI_OPCODE_FAST_READ 0x0b +#define SPI_OPCODE_TYPE_READ_NO_ADDRESS 0 +#define SPI_OPCODE_TYPE_WRITE_NO_ADDRESS 1 +#define SPI_OPCODE_TYPE_READ_WITH_ADDRESS 2 +#define SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS 3 +Thanks for changing this.
Quoted 19 lines
drivers/spi/ich.h +19
-0+#define SPI_OPMENU_0 0x01/* WRSR: Write Status Register */ +#define SPI_OPTYPE_0 SPI_OPCODE_TYPE_WRITE_NO_ADDRESS + +#define SPI_OPMENU_1 0x02/* BYPR: Byte Program */ +#define SPI_OPTYPE_1 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_2 0x03/* READ: Read Data */ +#define SPI_OPTYPE_2 SPI_OPCODE_TYPE_READ_WITH_ADDRESS + +#define SPI_OPMENU_3 0x05/* RDSR: Read Status Register */ +#define SPI_OPTYPE_3 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_4 0x20/* SE20: Sector Erase 0x20 */ +#define SPI_OPTYPE_4 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_5 0x9f/* RDID: Read ID */ +#define SPI_OPTYPE_5 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_6 0xd8/* BED8: Block Erase 0xd8 */
Quoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 151
Quoted 5 lines
drivers/spi/ich.h +5
-0+#define SPI_OPTYPE_6 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_7 0x0b/* FAST: Fast Read */ +#define SPI_OPTYPE_7 SPI_OPCODE_TYPE_READ_WITH_ADDRESS +These are SPI flash commands. Should we name them similarly like
SPI_OPCODE_WRENandSPI_OPCODE_FAST_READ?
I've thought about this as well but neglected doing this (for now). If you think its "better" that way, I'll send a v4 shortly. Just let me know.
Quoted 4 lines
Quoted 4 lines
drivers/spi/ich.h +4
-0+#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \ + (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) | \ + (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) | \ + (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0 << 0))
Quoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 160
Quoted 5 lines
drivers/spi/ich.h +5
-0+#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \ + (SPI_OPMENU_5 << 8) | (SPI_OPMENU_4 << 0)) +#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \ + (SPI_OPMENU_1 << 8) | (SPI_OPMENU_0 << 0)) +What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
An easy way to do this, would be to make the newly created function spi_controller_config() a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.
Thanks,
Stefan
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Stefan,
Quoted 50 lines · Stefan Roese
Hi Bin,
On 10.02.2017 06:45, Bin Meng wrote:
<snip>
Quoted 33 lines
drivers/spi/ich.h struct spi_trans { · line 127
Quoted 9 lines
drivers/spi/ich.h +5
-0@@ -127,6 +120,44 @@ struct spi_trans {#define SPI_OPCODE_WREN 0x06#define SPI_OPCODE_FAST_READ 0x0b +#define SPI_OPCODE_TYPE_READ_NO_ADDRESS 0 +#define SPI_OPCODE_TYPE_WRITE_NO_ADDRESS 1 +#define SPI_OPCODE_TYPE_READ_WITH_ADDRESS 2 +#define SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS 3 +Thanks for changing this.
Quoted 20 lines
drivers/spi/ich.h +20
-0+#define SPI_OPMENU_0 0x01/* WRSR: Write Status Register */ +#define SPI_OPTYPE_0 SPI_OPCODE_TYPE_WRITE_NO_ADDRESS + +#define SPI_OPMENU_1 0x02/* BYPR: Byte Program */ +#define SPI_OPTYPE_1 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_2 0x03/* READ: Read Data */ +#define SPI_OPTYPE_2 SPI_OPCODE_TYPE_READ_WITH_ADDRESS + +#define SPI_OPMENU_3 0x05/* RDSR: Read Status Register */ +#define SPI_OPTYPE_3 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_4 0x20/* SE20: Sector Erase 0x20 */ +#define SPI_OPTYPE_4 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_5 0x9f/* RDID: Read ID */ +#define SPI_OPTYPE_5 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_6 0xd8/* BED8: Block Erase 0xd8 */ +#define SPI_OPTYPE_6 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESSQuoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 151
Quoted 4 lines
drivers/spi/ich.h +4
-0+ +#define SPI_OPMENU_7 0x0b/* FAST: Fast Read */ +#define SPI_OPTYPE_7 SPI_OPCODE_TYPE_READ_WITH_ADDRESS +These are SPI flash commands. Should we name them similarly like
SPI_OPCODE_WRENandSPI_OPCODE_FAST_READ?
Quoted 4 lines
I've thought about this as well but neglected doing this (for now). If you think its "better" that way, I'll send a v4 shortly. Just let me know.
OK, let's leave it for now.
Quoted 24 lines
Quoted 7 lines
Quoted 7 lines
drivers/spi/ich.h +6
-0+#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \ + (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) | \ + (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) | \ + (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0 << 0)) +#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \ + (SPI_OPMENU_5 << 8) | (SPI_OPMENU_4 << 0))Quoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 160
Quoted 4 lines
drivers/spi/ich.h +3
-0+#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \ + (SPI_OPMENU_1 << 8) | (SPI_OPMENU_0 << 0)) +What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
Quoted 7 lines
An easy way to do this, would be to make the newly created function
spi_controller_config()a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.
I am OK with the weak implementation, but I know Simon dislikes weak :) Maybe he has a better idea.
Let's hear what others think.
Regards,
Bin
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi,
Quoted 92 lines · Bin Meng
Hi Stefan,
Quoted 50 lines · Stefan Roese
Hi Bin,
On 10.02.2017 06:45, Bin Meng wrote:
<snip>
Quoted 33 lines
drivers/spi/ich.h struct spi_trans { · line 127
Quoted 9 lines
drivers/spi/ich.h +5
-0@@ -127,6 +120,44 @@ struct spi_trans {#define SPI_OPCODE_WREN 0x06#define SPI_OPCODE_FAST_READ 0x0b +#define SPI_OPCODE_TYPE_READ_NO_ADDRESS 0 +#define SPI_OPCODE_TYPE_WRITE_NO_ADDRESS 1 +#define SPI_OPCODE_TYPE_READ_WITH_ADDRESS 2 +#define SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS 3 +Thanks for changing this.
Quoted 20 lines
drivers/spi/ich.h +20
-0+#define SPI_OPMENU_0 0x01/* WRSR: Write Status Register */ +#define SPI_OPTYPE_0 SPI_OPCODE_TYPE_WRITE_NO_ADDRESS + +#define SPI_OPMENU_1 0x02/* BYPR: Byte Program */ +#define SPI_OPTYPE_1 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_2 0x03/* READ: Read Data */ +#define SPI_OPTYPE_2 SPI_OPCODE_TYPE_READ_WITH_ADDRESS + +#define SPI_OPMENU_3 0x05/* RDSR: Read Status Register */ +#define SPI_OPTYPE_3 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_4 0x20/* SE20: Sector Erase 0x20 */ +#define SPI_OPTYPE_4 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS + +#define SPI_OPMENU_5 0x9f/* RDID: Read ID */ +#define SPI_OPTYPE_5 SPI_OPCODE_TYPE_READ_NO_ADDRESS + +#define SPI_OPMENU_6 0xd8/* BED8: Block Erase 0xd8 */ +#define SPI_OPTYPE_6 SPI_OPCODE_TYPE_WRITE_WITH_ADDRESSQuoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 151
Quoted 4 lines
drivers/spi/ich.h +4
-0+ +#define SPI_OPMENU_7 0x0b/* FAST: Fast Read */ +#define SPI_OPTYPE_7 SPI_OPCODE_TYPE_READ_WITH_ADDRESS +These are SPI flash commands. Should we name them similarly like
SPI_OPCODE_WRENandSPI_OPCODE_FAST_READ?Quoted 4 lines
I've thought about this as well but neglected doing this (for now). If you think its "better" that way, I'll send a v4 shortly. Just let me know.
OK, let's leave it for now.
Quoted 24 lines
Quoted 7 lines
Quoted 7 lines
drivers/spi/ich.h +6
-0+#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \ + (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) | \ + (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) | \ + (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0 << 0)) +#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \ + (SPI_OPMENU_5 << 8) | (SPI_OPMENU_4 << 0))Quoted 8 lines
drivers/spi/ich.h struct spi_trans { · line 160
Quoted 4 lines
drivers/spi/ich.h +3
-0+#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \ + (SPI_OPMENU_1 << 8) | (SPI_OPMENU_0 << 0)) +What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
Quoted 7 lines
An easy way to do this, would be to make the newly created function
spi_controller_config()a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.
Quoted 4 lines
I am OK with the weak implementation, but I know Simon dislikes weak :) Maybe he has a better idea.
Let's hear what others think.
Well how about crossing that bridge when we come to it? For now, perhaps this is good enough. You are right, I'm not keen on weak functions as I see them as ad-hoc APIs. Better, I believe, to think about it and define a real API. For example in this case I wonder if the remove() method of the SPI driver could do something? Or perhaps add another method like finalise()?
Regards,
Simon
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Simon,
On 22.02.2017 04:59, Simon Glass wrote:
<snip>
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
Quoted 2 lines
What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
An easy way to do this, would be to make the newly created function
spi_controller_config()a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.
Quoted 7 lines
Quoted 4 lines
I am OK with the weak implementation, but I know Simon dislikes weak :) Maybe he has a better idea.
Let's hear what others think.
Well how about crossing that bridge when we come to it? For now, perhaps this is good enough.
Thanks.
Quoted 5 lines
You are right, I'm not keen on weak
functions as I see them as ad-hoc APIs. Better, I believe, to think about it and define a real API. For example in this case I wonder if theremove()method of the SPI driver could do something? Or perhaps add another method likefinalise()?
Okay, lets think about this in more detail, once its necessary.
Thanks,
Stefan
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Stefan, Simon,
Quoted 39 lines · Stefan Roese
Hi Simon,
On 22.02.2017 04:59, Simon Glass wrote:
<snip>
Quoted 21 lines
Quoted 21 lines
Quoted 19 lines
Quoted 2 lines
What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
An easy way to do this, would be to make the newly created function
spi_controller_config()a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.Quoted 8 lines
Quoted 4 lines
I am OK with the weak implementation, but I know Simon dislikes weak :) Maybe he has a better idea.
Let's hear what others think.
Well how about crossing that bridge when we come to it? For now, perhaps this is good enough.
Thanks.
Quoted 9 lines
Quoted 5 lines
You are right, I'm not keen on weak
functions as I see them as ad-hoc APIs. Better, I believe, to think about it and define a real API. For example in this case I wonder if theremove()method of the SPI driver could do something? Or perhaps add another method likefinalise()?Okay, lets think about this in more detail, once its necessary.
What's next step for this patch? I see Stefan has done some patches on dm core.
Regards,
Bin
PATCH v3 1/1 spi: ich: Configure SPI BIOS parameters
Hi Bin,
Quoted 40 lines · Bin Meng
Quoted 40 lines
Quoted 21 lines
Quoted 21 lines
Quoted 19 lines
Quoted 2 lines
What if the board mounts a flash with a different SPI flash command set? Will this work?
Frankly, I can't tell for sure but its very likely. As you might have guessed, these defines are taken from coreboot where they are usually board specific and written in the last stage before booting into the OS (IIRC). It would definitely make sense to add a mechanism to configure these BIOS parameters in a board-specific way. So that boards can choose to (optionally) provide different values.
An easy way to do this, would be to make the newly created function
spi_controller_config()a wear default. This way, board can always overwrite these default values (and / or do other stuff) in their board specific code. This could also be added in a follow up patch once this is needed though. I still have to see such a case of an "incompatible" SPI flash on x86, and IIRC all values in coreboot were identical.Quoted 8 lines
Quoted 4 lines
I am OK with the weak implementation, but I know Simon dislikes weak :) Maybe he has a better idea.
Let's hear what others think.
Well how about crossing that bridge when we come to it? For now, perhaps this is good enough.
Thanks.
Quoted 5 lines
You are right, I'm not keen on weak
functions as I see them as ad-hoc APIs. Better, I believe, to think about it and define a real API. For example in this case I wonder if theremove()method of the SPI driver could do something? Or perhaps add another method likefinalise()?
Quoted 5 lines
Quoted 2 lines
Okay, lets think about this in more detail, once its necessary.
What's next step for this patch? I see Stefan has done some patches on dm core.
Correct, and this one would fit perfectly into this new DM removal / finalization framework. Additionally, I've just noticed yesterday, that this SPI patch is enough for the Linux Intel SPI NOR driver to correctly detect the NOR chip. But writing is not possible, since the SPI NOR seem to be protected. I still need to investigate here to fix this.
So I suggest to postpone this SPI patch until I have a newer, better version, perhaps already based on this DM remove framework.
Thanks,
Stefan