mtd: nand: gpio: make nCE GPIO optional
Subsystems (2)
PATCH 1/1 mtd: nand: gpio: make nCE GPIO optional
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/mtd/nand/gpio.c +12 -6
@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);
@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }
@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Signature · 1 line
2.10.1
Quoted 1 line · Christophe Leroy
On some hardware,
Can you be more specific or is that confidential ? Anyway, that's just my curiosity, what hardware is done like that.
Quoted 5 lines
the nCE signal is wired to the ChipSelect associated
to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.Signed-off-by Christophe Leroy <[email protected]>
but please wait for the NAND experts ...
Quoted 48 lines
--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)drivers/mtd/nand/gpio.c +12
-6@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Signature · 2 lines
Best regards, Marek Vasut
Quoted 3 lines · On Fri, 10 Feb 2017 15:01:10 +0100 (CET) Christophe Leroy…
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Hm, I'm not sure how this can work, because, AFAIR, the nCE line needs to stay low for the whole CMD+ADDR[+CMD] cycle, and with your patch it's not guaranteed.
Can you tell us more about your NAND controller?
Quoted 49 lines
Signed-off-by Christophe Leroy <[email protected]>--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)drivers/mtd/nand/gpio.c +12
-6@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Quoted 10 lines · Boris Brezillon
Quoted 3 lines · On Fri, 10 Feb 2017 15:01:10 +0100 (CET) Christophe Leroy…
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Hm, I'm not sure how this can work, because, AFAIR, the nCE line needs to stay low for the whole CMD+ADDR[+CMD] cycle, and with your patch it's not guaranteed.
Anyway, the patch just makes it possible to register the device allthough nCE GPIO is not defined. For people defining the nCE GPIO properly, the patch introduces no change at all.
Quoted 2 lines
Can you tell us more about your NAND controller?
[ 0.498490] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 0.504906] nand: Micron MT29F2G08ABAEAWP [ 0.508918] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Diagrams on datasheet shows that CE\ can optionnaly go up between each access. See attached exemple.
Quoted 50 lines
Quoted 50 lines
Signed-off-by Christophe Leroy <[email protected]>--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)drivers/mtd/nand/gpio.c +12
-6@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Quoted 8 lines · On Mon, 13 Feb 2017 13:58:24 +0100 Christophe LEROY <[email protected]>…
Quoted 7 lines · Boris Brezillon
Quoted 3 lines · On Fri, 10 Feb 2017 15:01:10 +0100 (CET) Christophe Leroy…
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Quoted 8 lines
Quoted 3 lines
Hm, I'm not sure how this can work, because, AFAIR, the nCE line needs to stay low for the whole CMD+ADDR[+CMD] cycle, and with your patch it's not guaranteed.
Anyway, the patch just makes it possible to register the device allthough nCE GPIO is not defined.
For people defining the nCE GPIO properly, the patch introduces no change at all.
Yes, I know that, just wanted to make sure that not explicitly controlling the CE line was permitted. Modern controllers are indeed controlling the CE line, but they usually ask you to specify the whole CMD+ADDR[+CMD][+DATA] sequence.
Quoted 11 lines
Quoted 3 lines
Can you tell us more about your NAND controller?
[ 0.498490] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 0.504906] nand: Micron MT29F2G08ABAEAWP [ 0.508918] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048,OOB size: 64
Diagrams on datasheet shows that CE\ can optionnaly go up between each access. See attached exemple.
I had a closer look at several datasheets (and the ONFI spec), and it seems to be allowed as long as you follow the tCS and tCH requirements, which I guess your controller is ensuring.
Quoted 53 lines
Quoted 53 lines
Quoted 53 lines
Signed-off-by Christophe Leroy <[email protected]>--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)drivers/mtd/nand/gpio.c +12
-6@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Boris Brezillon
AppliedQuoted 3 lines · On Fri, 10 Feb 2017 15:01:10 +0100 (CET) Christophe Leroy…
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Applied.
Thanks,
Boris
Quoted 49 lines
Signed-off-by Christophe Leroy <[email protected]>--- drivers/mtd/nand/gpio.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-)drivers/mtd/nand/gpio.c +12
-6@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)gpio_nand_dosync (gpiomtd);if (ctrl &NAND_CTRL_CHANGE ) { -gpio_set_value (gpiomtd->plat.gpio_nce, !(ctrl &NAND_NCE )); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce, + !(ctrl &NAND_NCE ));gpio_set_value (gpiomtd->plat.gpio_cle, !!(ctrl &NAND_CLE ));gpio_set_value (gpiomtd->plat.gpio_ale, !!(ctrl &NAND_ALE ));gpio_nand_dosync (gpiomtd);@@ -201,7 +203,8 @@ static int gpio_nand_remove(struct platform_device *pdev)if (gpio_is_valid (gpiomtd->plat.gpio_nwp))gpio_set_value (gpiomtd->plat.gpio_nwp,0 ); -gpio_set_value (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) +gpio_set_value (gpiomtd->plat.gpio_nce,1 );return 0 ; }@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)if (ret)return ret; - ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce,"NAND NCE" ); -if (ret) -return ret; -gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); +if (gpio_is_valid (gpiomtd->plat.gpio_nce)) { + ret =devm_gpio_request (&pdev->dev, gpiomtd->plat.gpio_nce, +"NAND NCE" ); +if (ret) +return ret; +gpio_direction_output (gpiomtd->plat.gpio_nce,1 ); + }if (gpio_is_valid (gpiomtd->plat.gpio_nwp)) { ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
Quoted 5 lines · Christophe Leroy
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Signed-off-by Christophe Leroy <[email protected]>
Not really a problem with this patch exactly, but FYI you're only making this optional for the non-DT case. For device tree, this is kinda hard to do, since the current binding suggests we retrieve the GPIOs based on index position, not by name. So if you leave one off...I guess we well just be off-by-1 on the indeces until we hit a non-optional one...which I guess is "CLE".
If we wanted this to work for DT, we'd need to extend this driver (and binding doc) to support requesting GPIOs by name.
Brian
Quoted 14 lines · Brian Norris
Quoted 5 lines · Christophe Leroy
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Signed-off-by Christophe Leroy <[email protected]>Not really a problem with this patch exactly, but FYI you're only making this optional for the non-DT case. For device tree, this is kinda hard to do, since the current binding suggests we retrieve the GPIOs based on index position, not by name. So if you leave one off...I guess we well just be off-by-1 on the indeces until we hit a non-optional one...which I guess is "CLE".
Quoted 3 lines
If we wanted this to work for DT, we'd need to extend this driver (and binding doc) to support requesting GPIOs by name.
It works for me with devicetree.
I have the following definition in my DT:
nand@1,0 {
compatible = "gpio-control-nand";
reg = <1 0x0 0x01>;
#address-cells = <1>;
#size-cells = <1>;
gpios = <&qe_pio_c 24 1 // RDY
0 // nCE
&qe_pio_c 26 1 // ALE
&qe_pio_c 25 1 // CLE
0>; // nwp
};Christophe
Quoted 23 lines · On Tue, 2 May 2017 07:47:40 +0200 Christophe LEROY <[email protected]>…
Quoted 14 lines · Brian Norris
Quoted 5 lines · Christophe Leroy
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Signed-off-by Christophe Leroy <[email protected]>Not really a problem with this patch exactly, but FYI you're only making this optional for the non-DT case. For device tree, this is kinda hard to do, since the current binding suggests we retrieve the GPIOs based on index position, not by name. So if you leave one off...I guess we well just be off-by-1 on the indeces until we hit a non-optional one...which I guess is "CLE".
Quoted 3 lines
If we wanted this to work for DT, we'd need to extend this driver (and binding doc) to support requesting GPIOs by name.
It works for me with devicetree.
I have the following definition in my DT:
Quoted 12 lines
nand@1,0 {
compatible = "gpio-control-nand";
reg = <1 0x0 0x01>;
#address-cells = <1>;
#size-cells = <1>;
gpios = <&qe_pio_c 24 1 // RDY
0 // nCE
&qe_pio_c 26 1 // ALE
&qe_pio_c 25 1 // CLE
0>; // nwp
};Yep, it's perfectly fine to have 'empty' gpio entries (entries with phandle set to 0/NULL), we're using this trick in the atmel_nand driver as well.
Hi Christophe, Boris,
Quoted 39 lines · Boris Brezillon
Quoted 23 lines · On Tue, 2 May 2017 07:47:40 +0200 Christophe LEROY <[email protected]>…
Quoted 14 lines · Brian Norris
Quoted 5 lines · Christophe Leroy
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO.
Signed-off-by Christophe Leroy <[email protected]>Not really a problem with this patch exactly, but FYI you're only making this optional for the non-DT case. For device tree, this is kinda hard to do, since the current binding suggests we retrieve the GPIOs based on index position, not by name. So if you leave one off...I guess we well just be off-by-1 on the indeces until we hit a non-optional one...which I guess is "CLE".
Quoted 3 lines
If we wanted this to work for DT, we'd need to extend this driver (and binding doc) to support requesting GPIOs by name.
It works for me with devicetree.
I have the following definition in my DT:
Quoted 12 lines
nand@1,0 { compatible = "gpio-control-nand"; reg = <1 0x0 0x01>; #address-cells = <1>; #size-cells = <1>; gpios = <&qe_pio_c 24 1 // RDY 0 // nCE &qe_pio_c 26 1 // ALE &qe_pio_c 25 1 // CLE 0>; // nwp };
Quoted 3 lines
Yep, it's perfectly fine to have 'empty' gpio entries (entries with phandle set to 0/NULL), we're using this trick in the
atmel_nanddriver as well.
I wasn't aware. In that case, you need to change the binding doc to note that nCE is optional now.
Brian