ath10k QCA988x firmware not supporting monitor mode
Hi!
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2
We are not able to run the wlan1 interface in monitor mode. The following error comes when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-modeath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 ath10k_pci 0001:03:00.0: firmware register dump:ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000 ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5 ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
------------[ cut here ]------------ WARNING: at fb83c3b8 [verbose debug info unavailable] Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O) uio_pdrv_genirq CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23 task: e6415500 ti: ef02a000 task.ti: ef02a000 NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0 REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+) MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0 NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211] LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
Call Trace:
[ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
[ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
[ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
[ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
[ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
[ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
[ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
[ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
[ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
[ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
--- Exception: c01 at 0xff4ff8c
LR = 0xffed2c0
Instruction dump:
39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
---[ end trace c9df4859ac192be7 ]---ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
Thank you
Regards
Diganta Jena
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi!
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2
We are not able to run the wlan1 interface in monitor mode. The following error comes when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
ath10k_pci 0001:03:00.0: firmware crashed! (uuid n/a)ath10k_pci 0001:03:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff sub 0000:0000) fw 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-modeath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 ath10k_pci 0001:03:00.0: firmware register dump:ath10k_pci 0001:03:00.0: [00]: 0x4100016C 0x00000000 0x0097F8D5 0x00000000 ath10k_pci 0001:03:00.0: [04]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [08]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [12]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [16]: 0x00000000 0x00000000 0x00000000 0x0097F8D5 ath10k_pci 0001:03:00.0: [20]: 0x00000000 0x00401930 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [24]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [28]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [32]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [36]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [40]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [44]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [48]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [52]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: [56]: 0x00000000 0x00000000 0x00000000 0x00000000 ath10k_pci 0001:03:00.0: failed to set 2g txpower 0: -108ath10k_pci 0001:03:00.0: failed to setup tx power 0: -108ath10k_pci 0001:03:00.0: failed to recalc tx power: -108
------------[ cut here ]------------ WARNING: at fb83c3b8 [verbose debug info unavailable] Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O) uio_pdrv_genirq CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23 task: e6415500 ti: ef02a000 task.ti: ef02a000 NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0 REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+) MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000
GPR00: fb83c3a8 ef02bd60 e6415500 ffffff94 eb865a40 00000152 00000000 00000000
GPR08: 00000000 00000001 00000000 00021002 84ad2e42 10025578 10100000 00000000
GPR16: 00000000 1000acb4 1001d264 1001d264 1001d1f8 ef98200c 00000000 e0e44000
GPR24: e0e44480 ffffffff 00000001 00000000 e0e44704 e0e40000 ffffff94 ef7ccba0 NIP [fb83c3b8] ieee80211_add_virtual_monitor+0xd8/0x1c0 [mac80211] LR [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211]
Call Trace:
[ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable)
[ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211]
[ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160
[ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180
[ef02be10] [c04d785c] dev_change_flags+0x1c/0x70
[ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0
[ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0
[ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0
[ef02bf10] [c0115520] SyS_ioctl+0x40/0x80
[ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c
--- Exception: c01 at 0xff4ff8c
LR = 0xffed2c0
Instruction dump:
39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd
7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0
---[ end trace c9df4859ac192be7 ]---ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdown
Please help me to set monitor mode on WiFi node.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
------- End of Forwarded Message -------
Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 9 lines · KAVITA MATHUR
Hi!
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2
[shafi] worth trying updated firmware
https://source.codeaurora.org/quic/qsdk/oss/firmware/ath10k-firmware/plain/ath10k/QCA988X/hw2.0/
Quoted 5 lines
We are not able to run the wlan1 interface in monitor mode. The following error comes when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
[shafi] can you please confirm the below fix is already available (its cced to stable though)
https://patchwork.kernel.org/patch/8481281/
and if you see still see the issue in latest backports
http://buildbot.w1.fi/backports-wireless-testing/
please revert back
Quoted 93 lines
ath10k_pci0001:03:00.0: firmware crashed! (uuid n/a)ath10k_pci0001:03:00.0: qca988x hw2.0 (0x4100016c,0x043202ffsub 0000:0000) fw 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-modeath10k_pci0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0ath10k_pci0001:03:00.0: firmware register dump:ath10k_pci0001:03:00.0: [00]:0x4100016C0x000000000x0097F8D50x00000000ath10k_pci0001:03:00.0: [04]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [08]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [12]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [16]:0x000000000x000000000x000000000x0097F8D5ath10k_pci0001:03:00.0: [20]:0x000000000x004019300x000000000x00000000ath10k_pci0001:03:00.0: [24]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [28]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [32]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [36]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [40]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [44]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [48]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [52]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [56]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: failed to set 2g txpower 0: -108ath10k_pci0001:03:00.0: failed to setup tx power 0: -108ath10k_pci0001:03:00.0: failed to recalc tx power: -108------------[ cut here ]------------ WARNING: at fb83c3b8 [verbose debug info unavailable] Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O) uio_pdrv_genirq CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23 task: e6415500 ti: ef02a000 task.ti: ef02a000 NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0 REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+) MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000GPR00:
fb83c3a8ef02bd60e6415500ffffff94eb865a4000000152 00000000 00000000
GPR08: 00000000 00000001 00000000 0002100284ad2e4210025578 10100000 00000000
GPR16: 000000001000acb41001d2641001d2641001d1f8ef98200c00000000e0e44000
GPR24:e0e44480ffffffff 00000001 00000000e0e44704e0e40000ffffff94ef7ccba0NIP [fb83c3b8]ieee80211_add_virtual_monitor+0xd8/0x1c0[mac80211] LR [fb83c3a8]ieee80211_add_virtual_monitor+0xc8/0x1c0[mac80211]Call Trace: [ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable) [ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211] [ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160 [ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180 [ef02be10] [c04d785c] dev_change_flags+0x1c/0x70 [ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0 [ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0 [ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0 [ef02bf10] [c0115520] SyS_ioctl+0x40/0x80 [ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c --- Exception: c01 at 0xff4ff8c LR = 0xffed2c0 Instruction dump: 39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd 7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0 ---[ end trace c9df4859ac192be7 ]---ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdownPlease help me to set monitor mode on WiFi node.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
------- End of Forwarded Message -------Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it
Quoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Hi,
Thanks a lot..
Now I am able to set monitor mode after applying the patch and latest firmware.
Thanks & Regards,
Kavita
On Wed, 1 Mar 2017 10:52:42 +0530, Mohammed Shafi Shajakhan wrote
Quoted 5 lines · KAVITA MATHUR
Quoted 4 lines
Hi!
Quoted 8 lines
Quoted 5 lines
We are using Atheros QCA9880 mPCIe module with ath10k drivers and firmware.
Kernel: 3.12
Backports: 4.4
Firmware:10.2.4.70.59-2[shafi] worth trying updated firmware
https://source.codeaurora.org/quic/qsdk/oss/firmware/ath10k-firmware/plain/ath10k/QCA988X/hw2.0/
Quoted 7 lines
Quoted 6 lines
We are not able to run the wlan1 interface in monitor mode. The following error comes when we do
iw phy phy1 interface add wlan1 type monitor
ifconfig wlan1 up
Quoted 106 lines
[shafi] can you please confirm the below fix is already available (its cced to stable though)
https://patchwork.kernel.org/patch/8481281/and if you see still see the issue in latest backports
http://buildbot.w1.fi/backports-wireless-testing/please revert back
Quoted 97 lines
ath10k_pci0001:03:00.0: firmware crashed! (uuid n/a)ath10k_pci0001:03:00.0: qca988x hw2.0 (0x4100016c,0x043202ffsub 0000:0000) fw 10.2.4.70.59-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-modeath10k_pci0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0ath10k_pci0001:03:00.0: firmware register dump:ath10k_pci0001:03:00.0: [00]:0x4100016C0x000000000x0097F8D50x00000000ath10k_pci0001:03:00.0: [04]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [08]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [12]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [16]:0x000000000x000000000x000000000x0097F8D5ath10k_pci0001:03:00.0: [20]:0x000000000x004019300x000000000x00000000ath10k_pci0001:03:00.0: [24]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [28]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [32]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [36]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [40]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [44]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [48]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [52]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: [56]:0x000000000x000000000x000000000x00000000ath10k_pci0001:03:00.0: failed to set 2g txpower 0: -108ath10k_pci0001:03:00.0: failed to setup tx power 0: -108ath10k_pci0001:03:00.0: failed to recalc tx power: -108------------[ cut here ]------------ WARNING: at fb83c3b8 [verbose debug info unavailable] Modules linked in: ath10k_pci(O) ath10k_core(O) mac80211(O) ath(O) cfg80211(O) compat(O) uio_pdrv_genirq CPU: 0 PID: 17173 Comm: ifconfig Tainted: G O 3.12.37-rt51+ #23 task: e6415500 ti: ef02a000 task.ti: ef02a000 NIP: fb83c3b8 LR: fb83c3a8 CTR: c00788f0 REGS: ef02bcb0 TRAP: 0700 Tainted: G O (3.12.37-rt51+) MSR: 00029002 <CE,EE,ME> CR: 84008482 XER: 20000000GPR00:
fb83c3a8ef02bd60e6415500ffffff94eb865a4000000152 00000000 00000000
GPR08: 00000000 00000001 00000000 0002100284ad2e4210025578 10100000 00000000
GPR16: 000000001000acb41001d2641001d2641001d1f8ef98200c00000000e0e44000
GPR24:e0e44480ffffffff 00000001 00000000e0e44704e0e40000ffffff94ef7ccba0NIP [fb83c3b8]ieee80211_add_virtual_monitor+0xd8/0x1c0[mac80211] LR [fb83c3a8]ieee80211_add_virtual_monitor+0xc8/0x1c0[mac80211]Call Trace: [ef02bd60] [fb83c3a8] ieee80211_add_virtual_monitor+0xc8/0x1c0 [mac80211] (unreliable) [ef02bd80] [fb83d168] ieee80211_do_open+0x4e8/0xa30 [mac80211] [ef02bdc0] [c04d73a8] __dev_open+0xe8/0x160 [ef02bdf0] [c04d76a0] __dev_change_flags+0xa0/0x180 [ef02be10] [c04d785c] dev_change_flags+0x1c/0x70 [ef02be30] [c057d930] devinet_ioctl+0x600/0x8e0 [ef02be90] [c04ba6f4] sock_ioctl+0x224/0x2e0 [ef02beb0] [c0115150] do_vfs_ioctl+0x410/0x7a0 [ef02bf10] [c0115520] SyS_ioctl+0x40/0x80 [ef02bf40] [c000fb04] ret_from_syscall+0x0/0x3c --- Exception: c01 at 0xff4ff8c LR = 0xffed2c0 Instruction dump: 39200008 913d038c 7fa3eb78 93dd000c 4bffe349 7fe3fb78 7fa4eb78 4bfee2cd 7c690034 5529d97e 7c7e1b78 69290001 <0f090000> 2f890000 7fa3eb78 40de00a0 ---[ end trace c9df4859ac192be7 ]---ieee80211 phy1: Hardware restart was requested
SIOCSIFFLAGS: Cannot send after transport endpoint shutdownPlease help me to set monitor mode on WiFi node.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any action in reliance on the contents of this information is strictly prohibited. The
sender does not accept liability for any errors or omissions in the contents of this
message, which arise as a result
------- End of Forwarded Message -------Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k