Skip to contentSkip to conversation

rtl8187: Enable monitor mode to fix multicast reception

PATCH In review Nils Holland 4 participants 6 messages Feb 20, 2017 – Mar 8, 2017 RTL8187 wireless driver

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 rtl8187: Enable monitor mode to fix multicast reception

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

Fix the issue by setting RTL818X_RX_CONF_MONITOR instead, which puts the card into monitor mode and resolves the problem so that multicast frames are sucessfully passed to the kernel.

The existence of the problem and the effectiveness of the solution has originally been confirmed on an 8187B based card with the USB id of 0bda:8197. Subsequent testing by Larry Finger on an 8187L based card, which follows the second (8187, i.e. "non-b") code path in the driver, has confirmed that the fix does not cause any noticeable regresssions there either.

---
 drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)
drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c +7 -9
index 231f84db9ab0..56a8686cd367 100644
@@ -946,8 +946,7 @@ static int rtl8187_start(struct ieee80211_hw *dev)
 		      (7 << 13 /* RX FIFO threshold NONE */) |
 		      (7 << 10 /* MAX RX DMA */) |
 		      RTL818X_RX_CONF_RX_AUTORESETPHY |
-		      RTL818X_RX_CONF_ONLYERLPKT |
-		      RTL818X_RX_CONF_MULTICAST;
+		      RTL818X_RX_CONF_ONLYERLPKT;
 		priv->rx_conf = reg;
 		rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
 
@@ -1319,12 +1318,11 @@ static void rtl8187_configure_filter(struct ieee80211_hw *dev,
 		priv->rx_conf ^= RTL818X_RX_CONF_FCS;
 	if (changed_flags & FIF_CONTROL)
 		priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
-	if (changed_flags & FIF_OTHER_BSS)
-		priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
-	if (*total_flags & FIF_ALLMULTI || multicast > 0)
-		priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
+	if (*total_flags & FIF_OTHER_BSS ||
+	    *total_flags & FIF_ALLMULTI || multicast > 0)
+		priv->rx_conf |= RTL818X_RX_CONF_MONITOR;
 	else
-		priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
+		priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR;
 
 	*total_flags = 0;
 
@@ -1332,10 +1330,10 @@ static void rtl8187_configure_filter(struct ieee80211_hw *dev,
 		*total_flags |= FIF_FCSFAIL;
 	if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
 		*total_flags |= FIF_CONTROL;
-	if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
+	if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) {
 		*total_flags |= FIF_OTHER_BSS;
-	if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
 		*total_flags |= FIF_ALLMULTI;
+	}
 
 	rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
 }
Signature · 1 line
2.11.1
Acked-by on v2 1/1
#1 lore raw
Quoted 9 lines · Nils Holland

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

Fix the issue by setting RTL818X_RX_CONF_MONITOR instead, which puts the card into monitor mode and resolves the problem so that multicast frames are sucessfully passed to the kernel.

Quoted 8 lines

The existence of the problem and the effectiveness of the solution has originally been confirmed on an 8187B based card with the USB id of 0bda:8197. Subsequent testing by Larry Finger on an 8187L based card, which follows the second (8187, i.e. "non-b") code path in the driver, has confirmed that the fix does not cause any noticeable regresssions there either.

Thanks,

Larry

Quoted 49 lines
---
 drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)
drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c +7 -9
index 231f84db9ab0..56a8686cd367 100644
@@ -946,8 +946,7 @@ static int rtl8187_start(struct ieee80211_hw *dev)
 		      (7 << 13 /* RX FIFO threshold NONE */) |
 		      (7 << 10 /* MAX RX DMA */) |
 		      RTL818X_RX_CONF_RX_AUTORESETPHY |
-		      RTL818X_RX_CONF_ONLYERLPKT |
-		      RTL818X_RX_CONF_MULTICAST;
+		      RTL818X_RX_CONF_ONLYERLPKT;
 		priv->rx_conf = reg;
 		rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
 
@@ -1319,12 +1318,11 @@ static void rtl8187_configure_filter(struct ieee80211_hw *dev,
 		priv->rx_conf ^= RTL818X_RX_CONF_FCS;
 	if (changed_flags & FIF_CONTROL)
 		priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
-	if (changed_flags & FIF_OTHER_BSS)
-		priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
-	if (*total_flags & FIF_ALLMULTI || multicast > 0)
-		priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
+	if (*total_flags & FIF_OTHER_BSS ||
+	    *total_flags & FIF_ALLMULTI || multicast > 0)
+		priv->rx_conf |= RTL818X_RX_CONF_MONITOR;
 	else
-		priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
+		priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR;
 
 	*total_flags = 0;
 
@@ -1332,10 +1330,10 @@ static void rtl8187_configure_filter(struct ieee80211_hw *dev,
 		*total_flags |= FIF_FCSFAIL;
 	if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
 		*total_flags |= FIF_CONTROL;
-	if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
+	if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) {
 		*total_flags |= FIF_OTHER_BSS;
-	if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
 		*total_flags |= FIF_ALLMULTI;
+	}
 
 	rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
 }
#2 lore raw
In reply to Nils Holland
Quoted 4 lines · Nils Holland

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

AFAIU you have RTL8187B chipset card only, but above message describes this as generic issue (including RTL8187 and RTL8187L).

Larry: were you able to reproduce this problem using RTL8187L? Is this workaround needed for that chipset as well? I couldn't find clear statement.

#3 lore raw
Quoted 11 lines · Rafał Miłecki
Quoted 4 lines · Nils Holland

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

AFAIU you have RTL8187B chipset card only, but above message describes this as generic issue (including RTL8187 and RTL8187L).

Larry: were you able to reproduce this problem using RTL8187L? Is this workaround needed for that chipset as well? I couldn't find clear statement.

Yes, the RTL8187L has the same problem as the RTL8187B. The fix is needed for both.

Larry

#4 lore raw
Quoted 7 lines · Larry Finger
Quoted 6 lines · Rafał Miłecki
Quoted 4 lines · Nils Holland

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

Quoted 7 lines
Quoted 5 lines

AFAIU you have RTL8187B chipset card only, but above message describes this as generic issue (including RTL8187 and RTL8187L).

Larry: were you able to reproduce this problem using RTL8187L? Is this workaround needed for that chipset as well? I couldn't find clear statement.

Yes, the RTL8187L has the same problem as the RTL8187B. The fix is needed for both.

OK, thanks for clarifying!

#5 lore raw
In reply to Nils Holland
Quoted 16 lines · Nils Holland

The rtl8187 cards don't seem to receive multicast frames, which, among other things, makes them fail to receive RAs in IPv6 networks. The cause seems to be that the RTL818X_RX_CONF_MULTICAST flag doesn't have the desired effect.

Fix the issue by setting RTL818X_RX_CONF_MONITOR instead, which puts the card into monitor mode and resolves the problem so that multicast frames are sucessfully passed to the kernel.

The existence of the problem and the effectiveness of the solution has originally been confirmed on an 8187B based card with the USB id of 0bda:8197. Subsequent testing by Larry Finger on an 8187L based card, which follows the second (8187, i.e. "non-b") code path in the driver, has confirmed that the fix does not cause any noticeable regresssions there either.

Quoted 2 lines

Patch applied to wireless-drivers-next.git, thanks.

3beb27028c44 rtl8187: Enable monitor mode to fix multicast reception

Signature · 6 lines
https://patchwork.kernel.org/patch/9581905/

Documentation about submitting wireless patches and checking status
from patchwork:

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches